6.7. Facility Alarms Command Reference

6.7.1. Command Hierarchies

Facility Alarm Configuration Commands
Show Commands

6.7.1.1. Facility Alarm Configuration Commands

config

— system

— alarms

— max-cleared maximum

— [no] shutdown

6.7.1.2. Show Commands

show

— system

— alarms [cleared] [severity severity-level] [count count] [newer-than days]

6.7.2. Command Descriptions

6.7.2.1. Configuration Commands

alarms

Syntax

alarms

Context

config>system

Supported Platforms

Supported on all 7210 SAS platforms as described in this document, including those configured in the access-uplink operating mode.

Description

This command enables the context to configure facility alarm parameters.

max-cleared

Syntax

max-cleared maximum

Context

config>system>alarms

Supported Platforms

Supported on all 7210 SAS platforms as described in this document, including those configured in the access-uplink operating mode

Description

This command configures the maximum number of cleared alarms that the system will store and display.

Default

500

Parameters

maximum—

Specifies the maximum number of cleared alarms.

Values—

0 to 500

shutdown

Syntax

[no] shutdown

Context

config>system>alarms

Supported Platforms

Supported on all 7210 SAS platforms as described in this document, including those configured in the access-uplink operating mode

Description

This command enables or disables the facility alarm functionality. When enabled, the facility alarm sub-system tracks active and cleared facility alarms and controls the alarm LEDs on the CPMs and CFMs. When facility alarm functionality is enabled, the alarms are viewed using the show system alarms commands.

Note:

Shutting down the system alarms clears all existing alarms (raised and cleared). Performing no shutdown will not bring back the earlier raised alarm.

Default

no shutdown

6.7.2.2. Show Commands

alarms

Syntax

alarms [cleared] [severity severity-level] [count count] [newer-than days]

Context

show>system

Supported Platforms

Supported on all 7210 SAS platforms as described in this document, including those configured in the access-uplink operating mode

Description

This command displays facility alarms on the system.

Parameters

cleared—

Displays the cleared alarm queue.

severity-level—

Specifies the severity level of the alarm.

Values—

critical | major | minor | warning

days—

Displays alarms that are newer than the number of days specified.

Values—

1 to 365

Output

The following output is an example of facility alarm information, and Table 66 describes the output fields.

Sample Output

*A:7210SAS# show system alarms

===============================================================================

Alarms [Critical:1 Major:2 Minor:0 Warning:0 Total:3]

===============================================================================

Index Date/Time Severity Alarm Resource

Details

-------------------------------------------------------------------------------

13 2014/11/13 14:34:39.20 MAJOR 7-2005-1 Chassis 1

Chassis: Temperature too high

12 2014/11/13 14:34:13.70 MAJOR 7-3002-1 Alarm Input Module 2

Alarm Input "Pin 2" ("2") has changed status to "alarm"

"Alarm Input

Triggered"

11 2014/11/13 14:32:37.00 CRITICAL 7-3001-1 Alarm Input Module 1

Alarm Input "Pin 1" ("1") has changed status to "alarm"

"Alarm Input

Triggered"

===============================================================================

*A:7210SAS#

Cleared alarms table:

A:Dut-A# show system alarms cleared

===============================================================================

Cleared Alarms [Size:500 Total:5 (not wrapped)]

===============================================================================

Index Date/Time Severity Alarm Resource

Details

-------------------------------------------------------------------------------

5 2011/04/01 18:11:55.00 MAJOR 7-2005-1 Chassis 1

Clear Chassis temperature too high alarm

3 2011/04/01 18:11:54.50 CRITICAL 7-2051-1 Power Supply 1

Clear Power Supply failure

2 2011/04/01 18:11:54.40 CRITICAL 7-2050-1 Power Supply 1

Clear Power Supply failure

4 2011/04/01 18:11:54.10 MINOR 7-2004-1 Fan 1

Clear Fan wrong type failure

1 2011/04/01 18:11:54.00 CRITICAL 7-2007-1 Power Supply 1

Clear Power Supply failure

===============================================================================

Table 66: Output Fields: Alarms

Label	Description
Index	Displays the alarm index number
Date/Time	Displays the date and time string for the alarm
Severity	Displays the severity level of the alarm
Alarm	Displays the alarm identifier
Resource	Displays the facility associated with the alarm
Details	Displays the description of the alarm