lldp
config>system
Supported on all 7210 SAS platforms as described in this document
Commands in this context configure system-wide Link Layer Discovery Protocol parameters.
lldp-med
config>system>lldp
7210 SAS-Dxp
This command creates the context to configure system-wide LLDP Media Endpoint Discovery (LLDP-MED) information.
network-policy network-policy-id [create]
no network-policy network-policy-id
config>system>lldp>lldp-med
7210 SAS-Dxp
This command configures network policies, which send configuration information using LLDP-MED TLVs. The configured policy specifies the network policy configuration that must be provided to the LLDP-MED endpoint device. Multiple policies can be configured with different application types.
By default, the system creates network policy 1, which is not associated with a port. The user must explicitly configure a policy for use with a port, or use the default network policy 1, and enable transmission and reception of LLDP-MED TLVs on the port.
The no form of the command removes the configured network policy ID.
Specifies the network policy ID.
Keyword to create a network policy.
application-type {voice | voice-signaling | guest-voice | guest-voice-signaling | soft-phone-voice | video-conferencing | streaming-video | video-signaling}
no application-type
config>system>lldp>lldp-med>network-policy
7210 SAS-Dxp
This command configures the application type for the specified network policy.
The configured application-type is used to match with the application type received from an LLDP-MED endpoint device and provides the endpoint device with the network policy configured for the requested application type.
The no form of this command configures the Network Policy TLV to send the application type value ‟not_specified” to the LLDP-MED endpoint device.
no application-type
Keyword to configure the voice application type for the network policy.
Keyword to configure the voice signaling application type for the network policy.
Keyword to configure the guest voice application type for the network policy.
Keyword to configure the guest voice signaling application type for the network policy.
Keyword to configure the soft phone voice application type for the network policy.
Keyword to configure the video conferencing application type for the network policy.
Keyword to configure the video streaming application type for the network policy.
Keyword to configure the video signaling application type for the network policy.
dot1p dot1p-value
no dot1p
config>system>lldp>lldp-med>network-policy
7210 SAS-Dxp
This command configures the dot1p value for the network policy.
The no form of this command reverts to the default value.
dot1p 0
Specifies the dot1p value.
ip-dscp ip-dscp
no ip-dscp
config>system>lldp>lldp-med>network-policy
7210 SAS-Dxp
This command configures the IP DSCP value for the network policy.
The no form of this command reverts to the default value.
ip-dscp 0
Specifies the IP DSCP value.
vlan-id vlan-id
no vlan-id
config>system>lldp>lldp-med>network-policy
7210 SAS-Dxp
This command configures the VLAN ID for the network policy.
The no form of this command reverts to the default value.
vlan-id 0
Specifies the VLAN ID.
[no] vlan-tag-present
config>system>lldp>lldp-med>network-policy
7210 SAS-Dxp
This command configures the application specified by the application-type to use a VLAN tagged packet, using the configured VLAN ID in the VLAN tag.
The no form of this command disables the use of a VLAN tag.
no vlan-tag-present
message-fast-tx time
no message-fast-tx
config>system>lldp
Supported on all 7210 SAS platforms as described in this document
This command configures the duration of the fast transmission period.
Specifies the fast transmission period, in seconds.
message-fast-tx-init count
no message-fast-tx-init
config>system>lldp
Supported on all 7210 SAS platforms as described in this document
This command configures the number of LLDPDUs to send during the fast transmission period.
Specifies the number of LLDPDUs to send during the fast transmission period.
notification-interval time
no notification-interval
config>system>lldp
Supported on all 7210 SAS platforms as described in this document
This command configures the minimum time between change notifications.
Specifies the minimum time, in seconds, between change notifications.
reinit-delay time
no reinit-delay
config>system>lldp
Supported on all 7210 SAS platforms as described in this document
This command configures the time before reinitializing LLDP on a port.
Specifies the time, in seconds, before reinitializing LLDP on a port.
tx-credit-max count
no tx-credit-max
config>system>lldp
Supported on all 7210 SAS platforms as described in this document
This command configures the maximum consecutive LLDPDUs transmitted.
Specifies the maximum consecutive LLDPDUs transmitted.
tx-hold-multiplier multiplier
no tx-hold-multiplier
config>system>lldp
Supported on all 7210 SAS platforms as described in this document
This command configures the multiplier of the tx-interval.
Specifies the multiplier of the tx-interval.
tx-interval interval
no tx-interval
config>system>lldp
Supported on all 7210 SAS platforms as described in this document
This command configures the LLDP transmit interval time.
Specifies the LLDP transmit interval time.