[no] ipv6
config>service>ies>if
7210 SAS-D, 7210 SAS-Dxp
Commands in this context configure IPv6 for an IES interface.
IES interface IPv6 commands are only supported for access-uplink SAPs on the 7210 SAS-D and 7210 SAS-Dxp.
address ipv6-address/prefix-length [eui-64]
no address ipv6-address/prefix-length
config>service>ies>if>ipv6
7210 SAS-D, 7210 SAS-Dxp
This command assigns an IPv6 address to the IES interface.
Specifies the IPv6 address on the interface.
Keyword that specifies that a complete IPv6 address from the supplied prefix and 64-bit interface identifier is formed. The 64-bit interface identifier is derived from the MAC address on Ethernet interfaces. For interfaces without a MAC address, for example ATM interfaces, the Base MAC address of the chassis is used.
icmp6
config>service>ies>if>ipv6
7210 SAS-D, 7210 SAS-Dxp
This command configures ICMPv6 parameters for the IES interface.
packet-too-big [number seconds]
no packet-too-big
config>service>ies>if>ipv6>icmp6
7210 SAS-D, 7210 SAS-Dxp
This command specifies whether ‟packet-too-big” ICMPv6 messages should be sent. When enabled, ICMPv6 ‟packet-too-big” messages are generated by this interface.
The no form of this command disables the sending of ICMPv6 ‟packet-too-big” messages.
100 10
Specifies the number of ‟packet-too-big” ICMPv6 messages to send in the time frame specified by the seconds parameter.
Specifies the time frame in seconds that is used to limit the number of ‟packet-too-big” ICMPv6 messages issued.
param-problem [number seconds]
no param-problem
config>service>ies>if>ipv6>icmp6
7210 SAS-D, 7210 SAS-Dxp
This command specifies whether ‟parameter-problem” ICMPv6 messages should be sent. When enabled, ‟parameter-problem” ICMPv6 messages are generated by this interface.
The no form of this command disables the sending of ‟parameter-problem” ICMPv6 messages.
100 10
Specifies the number of ‟parameter-problem” ICMPv6 messages to send in the time frame specified by the seconds parameter.
Specifies the time frame in seconds that is used to limit the number of ‟parameter-problem” ICMPv6 messages issued.
redirects [number seconds]
no redirects
config>service>ies>if>ipv6>icmp6
7210 SAS-D, 7210 SAS-Dxp
This command configures ICMPv6 ‟redirect” messages. When enabled, ICMPv6 redirects are generated when routes are not optimal on this router, and another router on the same subnetwork has a better route to alert that node that a better route is available.
The no form of this command disables the sending of ICMPv6 ‟redirect” messages.
100 10
Specifies the number of version 6 redirects are to be issued in the time frame specified by the seconds parameter.
Specifies the time frame in seconds that is used to limit the number of version 6 redirects issued.
time-exceeded [number seconds]
no time-exceeded
config>service>ies>if>ipv6>icmp6
7210 SAS-D, 7210 SAS-Dxp
This command specifies whether ‟time-exceeded” ICMPv6 messages should be sent. When enabled, ICMPv6 ‟time-exceeded” messages are generated by this interface.
The no form of this command disables the sending of ICMPv6 ‟time-exceeded” messages.
100 10
Specifies the number of ‟time-exceeded” ICMPv6 messages are to be issued in the time frame specified by the seconds parameter.
Specifies the time frame in seconds that is used to limit the number of ‟time-exceeded” ICMPv6 message to be issued.
unreachables [number seconds]
no unreachables
config>service>ies>if>ipv6>icmp6
7210 SAS-D, 7210 SAS-Dxp
This command specifies that ICMPv6 host and network ‟unreachables” messages are generated by this interface.
The no form of this command disables the sending of ICMPv6 host and network ‟unreachables” messages.
100 10
Specifies the number of destination ‟unreachables” ICMPv6 messages are issued in the time frame specified by the seconds parameter.
Specifies the time frame in seconds that is used to limit the number of destination ‟unreachables” ICMPv6 messages to be issued.
link-local-address ipv6-address [preferred]
no link-local-address
config>service>ies>if>ipv6
7210 SAS-D, 7210 SAS-Dxp
This command configures the IPv6 link local address.
Specifies the IPv6 link local address.
Specifies that the IPv6 address is the preferred IPv6 address for this interface. A preferred address is an address assigned to an interface whose use by upper layer protocols is unrestricted. A preferred addresses may be used as the source (or destination) address of packets sent from (or to) the interface.
neighbor ipv6-address mac-address
no neighbor ipv6-address
config>service>ies>if>ipv6
7210 SAS-D, 7210 SAS-Dxp
This command configures IPv6-to-MAC address mapping on the IES interface.
Specifies the IPv6 address of the interface for which to display information.
Specifies the 48-bit MAC address for the IPv6-to-MAC address mapping in the form aa:bb:cc:dd:ee:ff or aa-bb-cc-dd-ee-ff, where aa, bb, cc, dd, ee and ff are hexadecimal numbers. Allowed values are any non-broadcast, non-multicast MAC and non-IEEE reserved MAC addresses.