sap sap-id [create]
no sap sap-id
config>service>vprn>if
7210 SAS-K 2F6C4T and 7210 SAS-K 3SFP+ 8C
This command creates a Service Access Point (SAP) within a service. A SAP is a combination of port and encapsulation parameters that identify the service access point on the interface and within the 7210 SAS. Each SAP must be unique.
All SAPs must be explicitly created. If no SAPs are created within a service or on an IP interface, a SAP does not exist on that object.
Enter an existing SAP without the create keyword to edit SAP parameters. The SAP is owned by the service in which it was created.
A SAP can be associated with only a single service. A SAP can be defined only on a port that has been configured as an access port using the config port port-id ethernet mode access command.
If a port is shut down, all SAPs on that port become operationally down. When a service is shut down, SAPs for the service are not displayed as operationally down, although all traffic traversing the service is discarded. The operational state of a SAP is relative to the operational state of the port on which the SAP is defined.
The no form of this command deletes the SAP with the specified port. When a SAP is deleted, all configuration parameters for the SAP are also deleted.
A VPRN SAP must be defined on an Ethernet interface.
Specifies the physical port identifier portion of the SAP definition. See Common CLI command descriptions for command syntax.
Specifies the physical port ID in the slot/mda/port format.
If the card in the slot has Media Dependent Adapters (MDAs) installed, the port-id must be in the slot_number/MDA_number/port_number format. For example 2/3 specifies port 3 on MDA 2 in slot.
The port-id must reference a valid port type. The port must be configured as an access port.
Keyword used to create a SAP instance.
tod-suite tod-suite-name
no tod-suite
config>service>vprn>if>sap
7210 SAS-K 2F6C4T and 7210 SAS-K 3SFP+ 8C
This command applies a time-based policy (filter or QoS policy) to the SAP. The suite name must already exist in the config>cron context.
no tod-suite
Specifies a collection of policies (ACLs, QoS) including time-ranges that define the full or partial behavior of a SAP or a subscriber. The suite can be applied to more than one SAP.
accounting-policy acct-policy-id
no accounting-policy
config>service>vprn>if>sap
7210 SAS-K 2F6C4T and 7210 SAS-K 3SFP+ 8C
This command creates the accounting policy that can be applied to an interface SAP or interface SAP spoke-SDP.
An accounting policy must be defined before it can be associated with a SAP. If the policy-id does not exist, an error message is generated.
A maximum of one accounting policy can be associated with a SAP at one time. Accounting policies are configured in the config>log context.
The no form of this command removes the accounting policy association from the SAP, and the accounting policy reverts to the default.
Specifies the accounting policy-id as configured in the config>log>accounting-policy context.
[no] collect-stats
config>service>vprn>if>sap
7210 SAS-K 2F6C4T and 7210 SAS-K 3SFP+ 8C
This command enables accounting and statistical data collection for either an interface SAP or interface SAP spoke-SDP, or network port. When applying accounting policies, by default the data is collected in the appropriate records and written to the designated billing file.
When the no collect-stats command is issued, the statistics are still accumulated by the IOM cards. However, the CPU will not obtain the results and write them to the billing file. If a subsequent collect-stats command is issued, the counters written to the billing file include all the traffic while the no collect-stats command was in effect.
no collect-stats