dot1p dot1p-value [dot1p-mask]
no dot1p
config>qos>sap-ingress>mac-criteria>entry
Supported on all 7210 SAS platforms as described in this document, including those operating in access-uplink mode
This command configures the IEEE 802.1p value to be used as the match criterion.
The no form of this command removes the dot1p value as the match criterion.
Specifies the IEEE 802.1p value in decimal.
Specifies a 3-bit mask that can be configured using the following formats:
| Format Style | Format Syntax | Example |
|---|---|---|
Decimal |
D |
4 |
Hexadecimal |
0xH |
0x4 |
Binary |
0bBBB |
0b100 |
To select a range from 4 up to 7, specify p-value of 4 and a mask of 0b100 for value and mask.
dst-mac ieee-address [ieee-address-mask]
no dst-mac
config>qos>sap-ingress>mac-criteria>entry
Supported on all 7210 SAS platforms as described in this document, including those operating in access-uplink mode
This command configures a destination MAC address or range to be used as a Service Ingress QoS policy match criterion.
The no form of this command removes the destination mac address as the match criterion.
Specifies the MAC address to be used as a match criterion.
Specifies a 48-bit mask to match a range of MAC address values.
This 48-bit mask can be configured using the following formats:
| Format Style | Format Syntax | Example |
|---|---|---|
Decimal |
DDDDDDDDDDDDDD |
281474959933440 |
Hexadecimal |
0xHHHHHHHHHHHH |
0x0FFFFF000000 |
Binary |
0bBBBBBBB...B |
0b11110000...B |
All packets with a source MAC OUI value of 00-03-FA subject to a match condition should be specified as: 0003FA000000 0x0FFFFF000000
etype etype-value
no etype
config>qos>sap-ingress>mac-criteria>entry
Supported on all 7210 SAS platforms as described in this document, including those operating in access-uplink mode
This command configures an Ethernet type II value for use as a service ingress QoS policy match criterion.
The Ethernet type field is a two-byte field used to identify the protocol carried by the Ethernet frame. For example, 0800 is used to identify IPv4 packets.
The Ethernet type field is used by the Ethernet version-II frames. IEEE 802.3 Ethernet frames use the dsap, ssap or snap-pid fields as match criteria; the Ethernet type field is not used.
The snap-pid, etype, ssap, and dsap fields are mutually exclusive and cannot be part of the same match criteria.
The dataplane processes a maximum of two VLAN tags in a received packet. The Ethertype used in the MAC matching criteria for ACLs is the Ethertype that is found in the packet after processing single-tagged frames, double-tagged frames, and no-tag frames
The packet is considered to have no tags if at least one of the following criteria is true:
the packet is a null-tagged frame
the packet is a priority-tagged frame
the outermost Ethertype does not match the default Ethertype (0x8100)
the outermost Ethertype does not match the configured dot1q-etype on Dot1q encapsulated ports
the outermost Ethertype does not match the configured qinq-etype on QinQ encapsulated ports
The packet is considered to have a single tag if at least one of the following criteria is true:
the outermost Ethertype matches the default Ethertype (0x8100)
the outermost Ethertype matches the configured dot1q-etype on Dot1q encapsulated ports
the outermost Ethertype matches the configured qinq-etype on QinQ encapsulated ports
The packet is considered to have double tags if at least one of the following criteria is true:
the outermost Ethertype matches the default Ethernet type (0x8100)
the configured dot1q-etype on Dot1q encapsulated ports and the immediately following Ethertype match the default Ethertype (0x8100)
the configured qinq-etype on QinQ encapsulated ports and the immediately following Ethertype match the default Ethertype (0x8100)
The no form of this command removes the previously entered etype field as the match criteria.
Specifies the Ethernet type II frame Ethertype value to be used as a match criterion, expressed in decimal or hexadecimal.
src-mac ieee-address [ieee-address-mask]
no src-mac
config>qos>sap-ingress>mac-criteria>entry>match
Supported on all 7210 SAS platforms as described in this document, including those operating in access-uplink mode
This command configures a source MAC address or range to be used as a service ingress QoS policy match criterion.
The no form of this command removes the source mac as the match criteria.
Specifies the 48-bit IEEE MAC address to be used as a match criterion.
Specifies a 48-bit mask. This 48 bit mask can be configured using the following formats:
| Format Style | Format Syntax | Example |
|---|---|---|
Decimal |
DDDDDDDDDDDDDD |
281474959933440 |
Hexadecimal |
0xHHHHHHHHHHHH |
0x0FFFFF000000 |
Binary |
0bBBBBBBB...B |
0b11110000...B |
To configure all packets with a source MAC OUI value of 00-03-FA are subject to a match condition, then the entry should be specified as: 003FA000000 0xFFFFFF000000