dot1p-classification policy-id
no dot1p-classification
config>qos>sap-ingress
Supported on all 7210 SAS platforms as described in this document
This command specifies that the SAP ingress policy uses the dot1p classification for the specified policy ID.
The no form of this command reverts to the default.
policy-id 1
Specifies the SAP ingress policy ID that will use the dot1p classification.
dscp-classification policy-id
no dscp-classification
config>qos>sap-ingress
Supported on all 7210 SAS platforms as described in this document
This command specifies that the SAP ingress policy uses the DSCP classification for the specified policy ID.
The no form of this command reverts to the default.
policy id 1
Specifies the DSCP classification policy ID that the SAP ingress policy will use.
fc-meter-map policy-id [create]
no fc-meter-map policy-id
config>qos
7210 SAS-Mxp
This command specifies an FC meter map for a SAP ingress policy. The user cannot modify the FC meter map if it is being referenced by a SAP. The user must update the map before attaching SAP ingress policies on the SAPs.
A single user configurable fc-meter-map policy is available to be used by all SAP ingress policies.
The no form of this command reverts to the default FC meter map policy.
fc-meter-map 1
Specifies the policy ID for the FC meter map policy.
Specifies an FC meter map policy that is not the default.
counter-mode counter-mode
no counter-mode
config>qos>fc-meter-map
7210 SAS-Mxp
This command is used to configure a counter mode for an FC meter map policy. The in-out-profile-count parameter specifies that in-profile and out-profile packets and octets are counted per meter. The forward-drop-count parameter specifies that forwarded and dropped packets and octets are counted per meter. For all counter modes, packets and bytes are counted simultaneously. The counter counts the in-profile and out-profile packets and octets based on the final profile assigned by the meter/policer using the configured rates.
The no form of this command reverts to the default counter mode.
in-out-profile-count
Specifies which counter mode the FC meter map policy uses.
fc fc-name [create]
no fc fc-name
config>qos>fc-meter-map
7210 SAS-Mxp
This command configures FC to meter mappings for an FC meter map policy.
The no form of this command removes all the explicit FC to meter mappings and reverts to the default.
fc be
Specifies the forwarding class that is assigned as the default FC.
Keyword to create an FC for an FC meter map policy that is not the default.
broadcast-meter meter-id
no broadcast-meter
config>qos>fc-meter-map>fc
7210 SAS-Mxp
This command overrides the default broadcast forwarding type meter mapping for the fc fc-name command.
The meter-id parameter must exist within the policy before the mapping can be made. After the forwarding class mapping is executed, all broadcast traffic on a SAP that is using this policy is forwarded using the meter-id parameter specified.
The broadcast forwarding type usually tracks the multicast forwarding type definition. This command overrides that default behavior. For more information, see Use of the keyword ‟multipoint” for default meter ‟11” and Service ingress meter selection rules.
The no form of this command reverts the broadcast forwarding type meter-id parameter to the default of tracking the multicast forwarding type meter mapping.
Specifies the meter ID for the broadcast meter.
meter meter-id
no meter
config>qos>fc-meter-map>fc
7210 SAS-Mxp
This command overrides the default unicast forwarding type meter mapping for the fc fc-name command. The specified meter-id parameter must exist within the policy before the mapping can be made. After the forwarding class mapping is executed, all unicast traffic on a SAP using this policy is forwarded using the meter-id parameter specified.
If meter 11 is not configured in the policy, all multipoint traffic (that is, multicast, broadcast, and unknown-unicast traffic) is forwarded using the meter-id. For more information, see Use of the keyword ‟multipoint” for default meter ‟11” and Service ingress meter selection rules.
The no form of this command reverts the unicast meter-id to the default meter for the FC.
Specifies the meter ID for the meter.
multicast-meter meter-id
no multicast-meter
config>qos>fc-meter-map>fc
7210 SAS-Mxp
This command overrides the default multicast forwarding type meter mapping for the fc fc-name command. The specified meter-id parameter must exist within the policy before the mapping can be made. After the forwarding class mapping is executed, all multicast traffic on a SAP using this policy is forwarded using the meter-id.
The multicast forwarding type includes the unknown unicast forwarding type and the broadcast forwarding type unless each is explicitly defined to a different meter. When the unknown and broadcast forwarding types are left as default, they track the defined meter for the multicast forwarding type. For more information, see Use of the keyword ‟multipoint” for default meter ‟11” and Service ingress meter selection rules.
The no form of this command reverts the multicast forwarding type meter-id to the default meter for the forwarding class. If the broadcast and unknown forwarding types are not explicitly defined to a multipoint meter, they are also reverted to the default multipoint meter. By default, the multicast forwarding type uses meter 1, unless the default multipoint meter 11 is configured.
Specifies the meter ID for the multicast meter.
unknown-meter meter-id
no unknown-meter
config>qos>fc-meter-map>fc
7210 SAS-Mxp
This command overrides the default unknown unicast forwarding type meter mapping for the fc fc-name command. The specified meter-id parameter must exist within the policy before the mapping can be made. After the forwarding class mapping is executed, all unknown traffic on a SAP using this policy is forwarded using the meter-id.
The unknown forwarding type usually tracks the multicast forwarding type definition. This command overrides that default behavior. For more information, see Use of the keyword ‟multipoint” for default meter ‟11” and Service ingress meter selection rules.
The no form of this command reverts the unknown forwarding type to the default of tracking the multicast forwarding type meter mapping.
Specifies the meter ID for the unknown meter.
meter meter-id [create]
no meter meter-id
config>qos>fc-meter-map
7210 SAS-Mxp
This command configures a meter for an FC meter map policy.
Specifies the meter ID for the FC meter map policy.
Keyword to create a meter.