id service-id
clear>service
clear>service>statistics
Supported on all 7210 SAS platforms as described in this document, including those operating in access-uplink mode
This command clears commands for a specific service.
Specifies the ID that uniquely identifies a service.
statistics
clear>service>stats
Supported on all 7210 SAS platforms as described in this document, including those operating in access-uplink mode
This command clears session statistics for this service.
fdb {all | mac ieee-address | sap sap-id] | mesh-sdp sdp-id[:vc-id] | spoke-sdp sdp-id:vc-id}
clear>service>id
Supported on all 7210 SAS platforms as described in this document, including those operating in access-uplink mode
This command clears FDB entries for the service.
Clears all FDB entries.
Clears only FDB entries in the FDB table with the specified 48-bit MAC address. The MAC address can be expressed in the form aa:bb:cc:dd:ee:ff or aa-bb-cc-dd-ee-ff where aa, bb, cc, dd, ee and ff are hexadecimal numbers. This parameter is not supported on 7210 SAS platforms operating in access-uplink mode.
Specifies the physical port identifier portion of the SAP definition. See Common CLI command descriptions for command syntax.
Clears only service FDB entries associated with the specified mesh SDP ID. For a mesh SDP, the VC ID is optional. This parameter is not supported on 7210 SAS platforms operating in access-uplink mode.
Clears only service FDB entries associated with the specified spoke-SDP ID. For a spoke-SDP, the VC ID must be specified. This parameter is not supported on 7210 SAS platforms operating in access-uplink mode.
Specifies the SDP ID for which to clear associated FDB entries. This parameter is not supported on 7210 SAS platforms operating in access-uplink mode.
Specifies the virtual circuit ID on the SDP ID for which to clear associated FDB entries. This parameter is not supported on 7210 SAS platforms operating in access-uplink mode.
mesh-sdp sdp-id[:vc-id] ingress-vc-label
clear>service>id
Supported on all 7210 SAS platforms as described in this document, except those operating in access-uplink mode
This command clears and resets the mesh SDP bindings for the service.
Specifies the mesh SDP ID to be reset.
Specifies the virtual circuit ID on the SDP ID to be reset.
spoke-sdp sdp-id[:vc-id] {all | counters | stp | l2pt}}
clear>service>id
Supported on all 7210 SAS platforms as described in this document, except those operating in access-uplink mode
This command clears and resets the spoke-SDP bindings for the service.
The spoke-SDP ID to be reset.
The virtual circuit ID on the SDP ID to be reset.
Clears all queue statistics and STP statistics associated with the SDP.
Clears all queue statistics associated with the SDP.
Clears all STP statistics associated with the SDP.
Clears all L2PT statistics associated with the SDP.
sap sap-id
clear>service>statistics
Supported on all 7210 SAS platforms as described in this document, including those operating in access-uplink mode
This command clears statistics for the SAP bound to the service.
See Common CLI command descriptions for command syntax.
Clears all queue statistics and STP statistics associated with the SAP.
Clears all queue statistics associated with the SAP.
counters
clear>service>statistics>id
Supported on all 7210 SAS platforms as described in this document, including those operating in access-uplink mode
This command clears all traffic counters associated with the service ID.
l2pt
clear>service>statistics>id
Supported on all 7210 SAS platforms as described in this document, including those operating in access-uplink mode
This command clears the l2pt statistics for this service.
mesh-sdp sdp-id[:vc-id] {all | counters | stp | mrp}
clear>service>statistics>id
Supported on all 7210 SAS platforms as described in this document, except those operating in access-uplink mode
This command clears the statistics for a particular mesh SDP bind.
sdp-id - [1..17407]
vc-id - [1..4294967295]
Clears all queue statistics and STP statistics associated with the SDP.
Clears all queue statistics associated with the SDP.
Clears all STP statistics associated with the SDP.
Clears all MRP statistics associated with the SDP.
spoke-sdp sdp-id[:vc-id] {all | counters | stp | l2pt}
clear>service>statistics>id
Supported on all 7210 SAS platforms as described in this document, except those operating in access-uplink mode
This command clears statistics for the spoke-SDP bound to the service.
The spoke-SDP ID for which to clear statistics.
The virtual circuit ID on the SDP ID to be reset.
Clears all queue statistics and STP statistics associated with the SDP.
Clears all queue statistics associated with the SDP.
Clears all STP statistics associated with the SDP.
Clears all L2PT statistics associated with the SDP.
stp
clear>service>statistics>id
Supported on all 7210 SAS platforms as described in this document, including those operating in access-uplink mode
Clears all spanning tree statistics for the service ID.
detected-protocols {all | sap sap-id}
clear>service>id>stp
Supported on all 7210 SAS platforms as described in this document, including those operating in access-uplink mode
RSTP automatically falls back to STP mode when it receives an STP BPDU. The clear detected-protocols command forces the system to revert to the default RSTP mode on the SAP.
Clears all detected protocol statistics.
Clears the specified lease state SAP information. See Common CLI command descriptions for command syntax.
igmp-snooping
clear>service>id
Supported on all 7210 SAS platforms as described in this document, including those operating in access-uplink mode
Commands in this context clear IGMP snooping data.
port-db [sap sap-id] [group grp-address]
port-db sdp sdp-id:vc-id [group grp-address]
clear>service>id>igmp-snooping
Supported on all 7210 SAS platforms as described in this document, including those operating in access-uplink mode
This command clears the information about the IGMP snooping port database for the VPLS service.
Clears IGMP snooping statistics matching the specified SAP ID and optional encapsulation value. See Common CLI command descriptions for command syntax.
Clears only IGMP snooping entries associated with the specified mesh SDP or spoke-SDP. For a spoke-SDP, the VC ID must be specified, for a mesh SDP, the VC ID is optional.
Specifies the virtual circuit ID on the SDP ID for which to clear information.
Clears IGMP snooping statistics matching the specified group address.
querier
clear>service>id>igmp-snooping
Supported on all 7210 SAS platforms as described in this document, including those operating in access-uplink mode
This command clears the information about the IGMP snooping queriers for the VPLS service.