frame-relay
config>port>tdm>ds1>channel-group
config>port>tdm>ds3
config>port>tdm>e1>channel-group
config>port>tdm>e3
config>port>serial>v35>channel-group
config>port>serial>x21>channel-group
This command allows access to the context to configure the frame relay LMI operational parameters for a DS1/E1 channel group, a V.35 or X.21 SDI channel group, a DS-3/E-3 clear channel port, or a channelized DS3.
The no form of this command removes the frame relay LMI operational parameters.
lmi-type {ansi | itu | none | rev1}
no lmi-type
config>port>tdm>ds1>channel-group>frame-relay
config>port>tdm>ds3>frame-relay
config>port>tdm>e1>channel-group>frame-relay
config>port>tdm>e3>frame-relay
config>port>serial>v35>channel-group>frame-relay
config>port>serial>x21>channel-group>frame-relay
This command configures the LMI type for frame relay interfaces. LMIs are sets of enhancements to the basic frame relay specification.
itu
specifies ANSI T1.617 Annex D
specifies ITU-T Q933 Annex A
disable frame relay LMI on the port/channel
specifies Rev 1 version of ANSI T1.617 Annex D
mode {dce | dte | bidir}
no lmi-type
config>port>tdm>ds1>channel-group>frame-relay
config>port>tdm>ds3>frame-relay
config>port>tdm>e1>channel-group>frame-relay
config>port>tdm>e3>frame-relay
config>port>serial>v35>channel-group>frame-relay
config>port>serial>x21>channel-group>frame-relay
This command sets the frame relay interface to the DCE, DTE, or bidirectional mode of LMI operation. The DTE mode causes the router to send status enquiries over the interface. The DCE mode causes the router to respond to status enquiries. In bidirectional mode, the router performs both DTE and DCE operation over the FR interface. The bidirectional mode applies to the ANSI and ITU LMI types only.
This feature is used when two routers are connected back-to-back, running frame relay encapsulation.
dce
specifies the DCE mode
specifies the DTE mode
the bidirectional mode for LMI types ANSI and ITU
n391dte intervals
no n391dte
config>port>tdm>ds1>channel-group>frame-relay
config>port>tdm>ds3>frame-relay
config>port>tdm>e1>channel-group>frame-relay
config>port>tdm>e3>frame-relay
config>port>serial>v35>channel-group>frame-relay
config>port>serial>x21>channel-group>frame-relay
This command configures the DTE full status polling interval for the frame relay LMI. The number specifies the frequency at which inquiries expect a full status report.
The no form of this command returns the n391dte counter to the default value.
6
sets the number of exchanges to be done before requesting a full-status report. A value of 1 specifies to receive full-status messages only.
n392dce threshold
no n392dce
config>port>tdm>ds1>channel-group>frame-relay
config>port>tdm>ds3>frame-relay
config>port>tdm>e1>channel-group>frame-relay
config>port>tdm>e3>frame-relay
config>port>serial>v35>channel-group>frame-relay
config>port>serial>x21>channel-group>frame-relay
This command configures the DCE error threshold for the frame relay LMI. The threshold specifies the number of errors needed to bring down a link.
The no form of this command returns the n392dce counter to the default value.
3
sets the number of errors that will put the channel in an operationally down state
n392dte threshold
no n392dte
config>port>tdm>ds1>channel-group>frame-relay
config>port>tdm>ds3>frame-relay
config>port>tdm>e1>channel-group>frame-relay
config>port>tdm>e3>frame-relay
config>port>serial>v35>channel-group>frame-relay
config>port>serial>x21>channel-group>frame-relay
This command configures the DTE error threshold for the frame relay LMI. The threshold specifies the number of errors needed to bring down a link.
The no form of this command returns the n392dte counter to the default value.
3
sets the number of errors that will put the channel in an operationally down state
n393dce count
no n393dce
config>port>tdm>ds1>channel-group>frame-relay
config>port>tdm>ds3>frame-relay
config>port>tdm>e1>channel-group>frame-relay
config>port>tdm>e3>frame-relay
config>port>serial>v35>channel-group>frame-relay
config>port>serial>x21>channel-group>frame-relay
This command configures the DCE monitored event count for the frame relay LMI.
The no form of this command returns the n393dce counter to the default value.
4
sets the diagnostic window used to verify link integrity on the DCE interface
n393dte count
no n393dte
config>port>tdm>ds1>channel-group>frame-relay
config>port>tdm>ds3>frame-relay
config>port>tdm>e1>channel-group>frame-relay
config>port>tdm>e3>frame-relay
config>port>serial>v35>channel-group>frame-relay
config>port>serial>x21>channel-group>frame-relay
This command configures the DTE monitored event count for the frame relay LMI.
The no form of this command returns the n393dte counter to the default value.
4
sets the diagnostic window used to verify link integrity on the DTE interface
t391dte keepalive
no t391dte
config>port>tdm>ds1>channel-group>frame-relay
config>port>tdm>ds3>frame-relay
config>port>tdm>e1>channel-group>frame-relay
config>port>tdm>e3>frame-relay
config>port>serial>v35>channel-group>frame-relay
config>port>serial>x21>channel-group>frame-relay
This command configures the DTE keepalive timer for the frame relay LMI.
This number specifies the interval at which the DTE sends out a keepalive response request to the DCE.
The no form of this command returns the t391dte keepalive timer to the default value.
10
sets the interval, in seconds, between status inquiries issued by the DTE
t392dce keepalive
no t392dce
config>port>tdm>ds1>channel-group>frame-relay
config>port>tdm>ds3>frame-relay
config>port>tdm>e1>channel-group>frame-relay
config>port>tdm>e3>frame-relay
config>port>serial>v35>channel-group>frame-relay
config>port>serial>x21>channel-group>frame-relay
This command configures the DCE keepalive timer for the frame relay LMI.
This number specifies the interval at which the DCE checks for keepalive responses from the DTE.
The no form of this command returns the t392dce keepalive timer to the default value.
15
sets the expected interval, in seconds, between status inquiries issued by the DTE