4.6. PBB Show, Clear, and Debug Command Reference

This section describes the PBB show, clear, and debug command reference.

4.6.1. Command Hierarchies

4.6.1.1. Show Commands

show
association [ma-index] [detail]
cfm-stack-table port [{all-ports | all-sdps | all-virtuals}] [level 0 to 7] [direction up | down]
cfm-stack-table port-id [vlan qtag[.qtag]] [level 0 to 7] [direction up | down]
cfm-stack-table sdp sdp-id[:vc-id] [level 0 to 7] [direction up| down]
cfm-stack-table virtual service-id [level 0 to 7]
cfm-stack-table facility [{all-ports | all-lags | all-lag-ports | all-tunnel-meps | all-router-interfaces}] [level 0 to 7] [direction up | down]
cfm-stack-table facility collect-lmm-stats
cfm-stack-table facility lag id [tunnel 1 to 4094] [level 0 to 7] [direction up | down]
cfm-stack-table facility port id [level 0 to 7] [direction up | down]
cfm-stack-table facility router-interface ip-int-name [level 0 to 7] [direction up | down]
domain [md-index] [association ma-index | all-associations [detail]]
mep mep-id domain md-index association ma-index [loopback] [linktrace]
— service
id service-id
i-vpls
mrp-policy mac [ieee-address]
mrp
— spb
adjacency [detail]
base
fid [fid] fate-sharing
fid [fid] user-service
fid [fid] fdb
fid [fid] mfib [group-mac ieee-address]
fid [fid] mfib [isid isid]
mfib [detail]
routes
spf
status
mrp-policy [mrp-policy]
mrp-policy mrp-policy [association]
mrp-policy mrp-policy [entry entry-id]
— pbb
base
mac-name [detail]

4.6.1.2. Clear Commands

clear
— service
— statistics
id service-id
mesh-sdp sdp-id[:vc-id] {all | counters | stp | mrp}
mrp
spoke-sdp sdp-id[:vc-id] {all | counters | stp | mrp}
stp
spb
adjacency [detail]
status
sap sap-id {all | counters | stp | l2pt | mrp}

4.6.1.3. Debug Commands

debug
— service
id service-id
[no] mrp
[no] applicant-sm
[no] leave-all-sm
[no] mmrp-mac ieee-address
[no] mrpdu
[no] periodic-sm
[no] registrant-sm
[no] sap sap-id
[no] sdp sdp-id:vc-id

4.6.2. Command Descriptions

4.6.2.1. PBB Show Commands

The following command outputs are examples only; actual displays may differ depending on supported functionality and user configuration.

eth-cfm

Syntax 
eth-cfm
Context 
show
Description 

This command displays 802.1ag CFM information.

association

Syntax 
association [ma-index] [detail]
Context 
show>eth-cfm
Description 

Shows association information.

Parameters 
ma-index—
Specifies the MA index value
Values—
1 to 4294967295

 

detail—
Displays all association detail
Output 

The following output is an example of ETH-CFM association information.

Sample Output
ALU-IPD# show eth-cfm association
===============================================================================
CFM Association Table
===============================================================================
Md-index   Ma-index   Name                     Int  Hold  Bridge-id  MEPS TxSid
-------------------------------------------------------------------------------
10         1          port1/1/1                10   n/a   none       1    no
12         1          ipinterface192.168.2.0   1    n/a   none       2    yes
12         4000       vpls-4000-l2             1    n/a   4000       2    yes
12         4001       vpls-4001-l2             1    n/a   4001       2    yes
12         5001       vprn-5001-10.101.28.1    1    n/a   5001       2    no
13         1000       vpls-1000-l3             1    n/a   1000       3    yes
13         1500       epipe-1500-13            1    n/a   1500       2    yes
13         2000       vpls-2000-l3             1    n/a   2000       5    yes
13         2002       vpls-2002-13             1    n/a   2002       2    yes
13         3000       vpls-3000-l3             1    n/a   3000       4    yes
13         4000       vpls-4000-l3             1    n/a   4000       2    yes
13         4001       vpls-4001-l3             1    n/a   4001       2    yes
14         100        vpls-100-l4              1    n/a   100        4    yes
14         1000       vpls-1000-l4             10   n/a   1000       1    no
14         2000       vpls-2000-l4             10   n/a   2000       0    yes
14         4000       vpls-4000-l4             10   n/a   4000       0    yes
14         4001       vpls-4001-l4             1    n/a   4001       1    yes
15         1000       vpls-1000-l5             10   n/a   1000       0    no
15         2000       vpls-2000-l5             10   n/a   2000       0    yes
15         4000       vpls-4000-l5             10   n/a   4000       0    yes
===============================================================================
ALU-IPD#

cfm-stack-table

Syntax 
cfm-stack-table
cfm-stack-table [{all-ports | all-sdps | all-virtuals}] [level 0 to 7] [direction up | down]
cfm-stack-table port port-id [vlan qtag[.qtag]] [level 0 to 7] [direction up | down]
cfm-stack-table sdp sdp-id[:vc-id] [level 0 to 7] [direction up | down]
cfm-stack-table virtual service-id [level 0 to 7]
cfm-stack-table facility [{all-ports | all-lags | all-lag-ports | all-tunnel-meps | all-router-interfaces}] [level 0 to 7] [direction up | down]
cfm-stack-table facility collect-lmm-stats
cfm-stack-table facility lag lag-id [tunnel 1 to 4094] [level 0 to 7] [direction up | down]
cfm-stack-table facility port port-id [level 0 to 7] [direction up | down]
cfm-stack-table facility router-interface ip-int-name [level 0 to 7] [direction up | down]
Context 
show>eth-cfm
Description 

This command displays stack table information. This stack table is used to display the various management points MEPs and MIPs that are configured on the system. These can be Service based or facility based. The various option allow the operator to be specific. If no parameters are include then the entire stack table will be displayed.

Parameters 
all-ports—
Displays stack table information for all ports
all-sdps—
Displays stack table information for all SDPs
all-virtuals—
Displays stack table information for all virtual circuits
all-lags—
Displays stack table information for all LAGs
all-lag-parts—
Displays stack table information for all LAG parts
all-tunnel-meps—
Displays stack table information for all tunnel MEPs
all-router-interfaces—
Displays stack table information for all router interfaces
level 0 to 7
Displays the MD level of the maintenance point
Values—
0 to 7

 

direction up | down—
Displays the direction in which the MP faces on the bridge port
port-id—
Displays the bridge port or aggregated port on which MEPs or MHFs are configured
lag-id—
Displays stack table information for the specified LAG
qtag—
Specifies a VLAN qtag
service-id—
Displays CFM stack table information for the specified SDP
tunnel 1 to 4094
Displays information for the specified tunnel
Values—
1 to 4094

 

facility—
Displays the CFM stack table information for facility MEPs. The base command will display all the facility MEPs. Options may be included in order to further parse the table for specific facility MEP information.
sdp-id[:vc-id]
Displays CFM stack table information for the specified SDP
ip-int-name—
Displays stack table information for the specified IP interface
collect-lmm-stats—
Displays collected LMM statistics for the facility
Output 

The following output is an example of ETH-CFM stack table information.

Sample Output
show eth-cfm cfm-stack-table
===============================================================================
CFM Stack Table Defect Legend:
R = Rdi, M = MacStatus, C = RemoteCCM, E = ErrorCCM, X = XconCCM
A = AisRx, L = CSF LOS Rx, F = CSF AIS/FDI rx, r = CSF RDI rx
G = receiving grace PDU (MCC-ED or VSM) from at least one peer
===============================================================================
CFM SAP Stack Table
===============================================================================
Sap                Lvl Dir Md-index   Ma-index  MepId  Mac-address     Defect G
-------------------------------------------------------------------------------
1/2/1:51.28          2 D         12       5001   28 d8:1c:01:02:00:01 --C---- -
1/2/1:1000.1000      3 U         13       1000   28 00:00:00:00:00:28 ---E--- -
1/2/1:1001.1001      1 B          0          0  MIP d8:1c:01:02:00:01 ------- -
1/2/1:1500.1500      3 U         13       1500   28 00:00:00:00:00:28 ------- -
1/2/1:2000.2000      3 U         13       2000  128 d8:1c:01:02:00:01 ------- -
1/2/1:2000.2000      4 B         14       2000  MIP 00:00:00:00:01:28 ------- -
1/2/1:3000.3000      4 B          0          0  MIP d8:1c:01:02:00:01 ------- -
1/2/1:4000.*         3 U         13       4000   28 00:00:00:00:00:28 ------- -
1/2/1:4001.*         3 U         13       4001   28 00:00:00:00:00:28 ------- -
1/2/1:4001.*         4 D         14       4001   28 00:00:00:00:00:28 ------- -
===============================================================================
 
===============================================================================
CFM Ethernet Tunnel Stack Table
===============================================================================
Eth-tunnel         Lvl Dir Md-index   Ma-index  MepId  Mac-address     Defect G
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================
 
===============================================================================
CFM Ethernet Ring Stack Table
===============================================================================
Eth-ring           Lvl Dir Md-index   Ma-index  MepId  Mac-address     Defect G
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================
 
===============================================================================
CFM Facility Port Stack Table
===============================================================================
Port     Tunnel    Lvl Dir Md-index   Ma-index  MepId  Mac-address     Defect G
-------------------------------------------------------------------------------
1/1/1     0          0 D         10          1   28 d8:1c:01:01:00:01 ------- -
===============================================================================
 
===============================================================================
CFM Facility LAG Stack Table
===============================================================================
Lag      Tunnel    Lvl Dir Md-index   Ma-index  MepId  Mac-address     Defect G
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================
 
===============================================================================
CFM Facility Tunnel Stack Table
===============================================================================
Port/Lag Tunnel    Lvl Dir Md-index   Ma-index  MepId  Mac-address     Defect G
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================
 
===============================================================================
CFM Facility Interface Stack Table
===============================================================================
Interface          Lvl Dir Md-index   Ma-index  MepId  Mac-address     Defect G
-------------------------------------------------------------------------------
v28-v29-1/1/6        2 D         12          1   28 00:00:00:00:00:28 ------- -
===============================================================================
 
===============================================================================
CFM SAP Primary VLAN Stack Table
===============================================================================
Sap
  Primary VlanId   Lvl Dir Md-index   Ma-index  MepId  Mac-address     Defect G
-------------------------------------------------------------------------------
1/1/10:2002.*
    2002             3 U         13       2002   28 00:00:00:00:00:28 ------- -
1/2/1:4000.*
    4000             4 B         14       4000  MIP d8:1c:01:02:00:01 ------- -
    4000             5 B         15       4000  MIP d8:1c:01:02:00:01 ------- -
===============================================================================
 
===============================================================================
CFM SDP Stack Table
===============================================================================
Sdp                Lvl Dir Md-index   Ma-index  MepId  Mac-address     Defect G
-------------------------------------------------------------------------------
2829:4001            2 D         12       4001   28 00:00:00:00:00:28 ------- -
===============================================================================
 
===============================================================================
CFM SDP Primary VLAN Stack Table
===============================================================================
Sdp
  Primary VlanId   Lvl Dir Md-index   Ma-index  MepId  Mac-address     Defect G
-------------------------------------------------------------------------------
2829:4000
    4000             2 D         12       4000   28 00:00:00:00:00:28 ------- -
    4000             4 B         14       4000  MIP d8:1c:ff:00:00:00 ------- -
    4000             5 B         15       4000  MIP d8:1c:ff:00:00:00 ------- -
===============================================================================
 
===============================================================================
CFM Virtual Stack Table
===============================================================================
Service            Lvl Dir Md-index   Ma-index  MepId  Mac-address     Defect G
-------------------------------------------------------------------------------
100                  4 U         14        100   28 00:00:00:00:00:28 ------- -
1000                 4 U         14       1000   28 d8:1c:ff:00:00:00 ---E--- -
2000                 3 U         13       2000   28 00:00:00:00:00:28 ------- -
3000                 3 U         13       3000   28 00:00:00:00:00:28 R-C---- -
===============================================================================

domain

Syntax 
domain [md-index] [association ma-index | all-associations [detail]]
Context 
show>eth-cfm>domain
Description 

This command displays domain information.

Parameters 
md-index—
Specifies the maintenance domain (MD) index value
Values—
1 to 4294967295

 

ma-index—
Specifies the MA index value
Values—
1 to 4294967295

 

all-associations—
Displays information all maintenance associations
detail—
Displays detailed information.
Output 

The following output is an example of ETH-CFM domain information.

Sample Output
*A:node-1# show eth-cfm domain
===============================================================================
CFM Domain Table
===============================================================================
Md-index   Level Name                                       Format
-------------------------------------------------------------------------------
10         0     InfrastructureL0                           CharString
12         2                                                none
13         3                                                none
14         4                                                none
15         5                                                none
===============================================================================

mep

Syntax 
mep mep-id domain md-index association ma-index [loopback] [linktrace]
Context 
show>eth-cfm>domain
Description 

This command displays Maintenance Endpoint (MEP) information.

Parameters 
mep-id—
Specifies the maintenance association end point identifier
Values—
1 to 8191

 

md-index—
Specifies the maintenance domain (MD) index value
Values—
1 to 4294967295

 

ma-index—
Specifies the MA index value
Values—
1 to 4294967295

 

loopback—
Displays loopback information for the specified MEP
linktrace—
Displays linktrace information for specified MEP
Output 

The following output is an example of ETH-CFM MEP information.

Sample Output
# show eth-cfm mep 28 domain 13 association 1000
===============================================================================
Eth-Cfm MEP Configuration Information
===============================================================================
Md-index         : 13                       Direction         : Up
Ma-index         : 1000                     Admin             : Enabled
MepId            : 28                       CCM-Enable        : Enabled
IfIndex          : 37781504                 PrimaryVid        : 65537000
Description      : (Not Specified)
FngAlarmTime     : 0                        FngResetTime      : 1000
FngState         : fngReset                 ControlMep        : False
LowestDefectPri  : xcon                     HighestDefect     : none
Defect Flags     : bDefErrorCCM
Mac Address      : 00:00:00:00:00:28        Collect LMM Stats : disabled
LMM FC Stats     : None
LMM FC In Prof   : None
TxAis            : noTransmit               TxGrace           : noTransmit
Facility Fault   : disabled
CcmLtmPriority   : 7                        CcmPaddingSize    : 0 octets
CcmTx            : 189745                   CcmSequenceErr    : 0
CcmTxIfStatus    : Up                       CcmTxPortStatus   : Up
CcmTxRdi         : False                    CcmTxCcmStatus    : transmit
CcmIgnoreTLVs    : (Not Specified)
Fault Propagation: disabled                 FacilityFault     : n/a
MA-CcmInterval   : 1                        MA-CcmHoldTime    : 0ms
MA-Primary-Vid   : Disabled
Eth-1Dm Threshold: 3(sec)                   MD-Level          : 3
Eth-1Dm Last Dest: 00:00:00:00:00:00
Eth-Dmm Last Dest: 00:00:00:00:00:00
Eth-Ais          : Disabled
Eth-Ais Tx defCCM: allDef
Eth-Tst          : Enabled                  Eth-Tst Pattern   : allZerosNoCrc
Eth-Tst dataLeng*: 64                       Eth-Tst Priority  : 7
Eth-Tst Dest Mac : 00:00:00:00:00:00        Eth-Tst Dest MEP  : 0
Eth-Tst Threshold: 1(bitError)
Eth-Tst Last Dest: 00:00:00:00:00:00
Eth-CSF          : Disabled
Eth-Cfm Grace Tx : Enabled                  Eth-Cfm Grace Rx  : Enabled
Eth-Cfm ED Tx    : Disabled                 Eth-Cfm ED Rx     : Enabled
Eth-Cfm ED Rx Max: 0
Eth-Cfm ED Tx Pri: CcmLtmPri (7)
Redundancy:
    MC-LAG State : n/a
CcmLastFailure Frame:
    None
XconCcmFailure Frame:
    None
===============================================================================
* indicates that the corresponding row element may have been truncated.
 
show eth-cfm mep 28 domain 13 association 1000 all-remote-mepids
=============================================================================
Eth-CFM Remote-Mep Table
=============================================================================
R-mepId AD Rx CC RxRdi Port-Tlv If-Tlv Peer Mac Addr     CCM status since
-----------------------------------------------------------------------------
29         True  False Up       Up     00:00:00:00:00:29 01/04/2017 06:03:05
31         True  False Up       Up     00:00:00:00:00:31 01/04/2017 06:03:09
=============================================================================
Entries marked with a 'T' under the 'AD' column have been auto-discovered.
 
show eth-cfm mep 28 domain 13 association 1000 all-remote-mepids detail
===============================================================================
Eth-CFM Remote-MEP Information
===============================================================================
Remote MEP ID    : 29                   CC Rx State      : True
Auto Discovered  : False                RDI              : False
Port Status TLV  : Up                   I/F Status TLV   : Up
MAC Address      : 00:00:00:00:00:29    CCM Last Change  : 01/04/2017 06:03:05
Chass. ID SubType: chassisComponent
Chassis ID       : 63:73:65:73:2D:76:32:39
                   "cses-v29"
Remote MEP ID    : 31                   CC Rx State      : True
Auto Discovered  : False                RDI              : False
Port Status TLV  : Up                   I/F Status TLV   : Up
MAC Address      : 00:00:00:00:00:31    CCM Last Change  : 01/04/2017 06:03:09
Chass. ID SubType: chassisComponent
Chassis ID       : 63:73:65:73:2D:56:33:31
                   "cses-V31"
===============================================================================
 
show eth-cfm mep 28 domain 13 association 1000 remote-mepid 29     
=============================================================================
Eth-CFM Remote-Mep Table
=============================================================================
R-mepId AD Rx CC RxRdi Port-Tlv If-Tlv Peer Mac Addr     CCM status since
-----------------------------------------------------------------------------
29         True  False Up       Up     00:00:00:00:00:29 01/04/2017 06:03:05
=============================================================================
Entries marked with a 'T' under the 'AD' column have been auto-discovered.
 
show eth-cfm mep 28 domain 13 association 1000 remote-mepid 29 detail
===============================================================================
Eth-CFM Remote-MEP Information
===============================================================================
Remote MEP ID    : 29                   CC Rx State      : True
Auto Discovered  : False                RDI              : False
Port Status TLV  : Up                   I/F Status TLV   : Up
MAC Address      : 00:00:00:00:00:29    CCM Last Change  : 01/04/2017 06:03:05
Chass. ID SubType: chassisComponent
Chassis ID       : 63:73:65:73:2D:76:32:39
                   "cses-v29"
===============================================================================

i-vpls

Syntax 
i-vpls
Context 
show>service>id
Description 

Displays I-VPLS services associated with the B-VPLS service. This command only applies when the service is a B-VPLS.

Output 

The following output is an example of service I-VPLS information.

Sample Output
*A:SetupCLI# show service id 2002 i-vpls 
================================================================
Related iVpls services for bVpls service 2002
================================================================
iVpls SvcId         Oper ISID           Admin               Oper
-------------------------------------------------------------------------------
2001                122                 Up                  Down
-------------------------------------------------------------------------------
Number of Entries : 1
-------------------------------------------------------------------------------
*A:alcag1-R6#
*A:term17>show>service>id# i-vpls
===============================================================================
Related iVpls services for bVpls service 2000
===============================================================================
iVpls SvcId         Oper ISID           Admin               Oper
-------------------------------------------------------------------------------
2100                2100                Up                  Up
2110                123                 Up                  Up
-------------------------------------------------------------------------------
Number of Entries : 2
-------------------------------------------------------------------------------
*A:SetupCLI#

base

Syntax 
base
Context 
show>service>pbb
Description 

This command displays information about a PBB base.

Output 

The following output is an example of PBB base information.

Sample
*A:Dut-B# show service pbb base 
======================================================================
PBB MAC Information
======================================================================
MAC-Notif Count : 3
MAC-Notif Interval : 1
Source BMAC : Default
======================================================================

mac-name

Syntax 
mac-name [detail]
Context 
show>service>pbb
Description 

This command displays information on a specific MAC name.

Parameters 
detail—
Displays detailed MAC name information.
Output 

The following output is an example of PBB MAC information.

Sample
*A:Dut-B# show service pbb mac-name 
=====================================================================
MAC Name Table
=====================================================================
MAC-Name MAC-Address
---------------------------------------------------------------------
test 00:03:03:03:03:02
=====================================================================
*A:Dut-B# show service pbb mac-name test detail 
=====================================================================
Services Using MAC name='test' addr='00:03:03:03:03:02'
=====================================================================
Svc-Id ISID
---------------------------------------------------------------------
501 501
---------------------------------------------------------------------
Number of services: 1
=====================================================================
*A:Dut-B# 

id

Syntax 
id service-id
Context 
show>service
Description 

This command displays information on a specific service ID.

Parameters 
service-id—
Specifies the service ID.
Output 

The following output is an example of service ID information.

Sample
*A:Dut-B# show service id 1 all 
===============================================================================
Service Detailed Information
===============================================================================
Service Id : 1 Vpn Id : 0
Service Type : b-VPLS
Description : (Not Specified)
Customer Id : 1
Last Status Change: 05/17/2009 19:33:11
Last Mgmt Change : 05/17/2009 19:31:59
Admin State : Up Oper State : Up
MTU : 2000 Def. Mesh VC Id : 1
SAP Count : 1 SDP Bind Count : 0
Snd Flush on Fail : Disabled Host Conn Verify : Disabled
Propagate MacFlush: Disabled
Oper Backbone Src : 00:03:00:00:04:01 Use SAP B-MAC : enabled 
i-Vpls Count : 0
Epipe Count : 900
*A:Dut-B# show service id 501 all
===============================================================================
Service Detailed Information
===============================================================================
Service Id : 501 Vpn Id : 0
Service Type : Epipe
Description : (Not Specified)
Customer Id : 1
Last Status Change: 05/17/2009 19:41:32
Last Mgmt Change : 05/17/2009 19:40:03
Admin State : Up Oper State : Up
MTU : 1514
Vc Switching : False
SAP Count : 1 SDP Bind Count : 0
-------------------------------------------------------------------------------
PBB Tunnel Point
-------------------------------------------------------------------------------
B-vpls Backbone-dest-MAC Isid AdmMTU OperState Flood Oper-dest-MAC
-------------------------------------------------------------------------------
1 test 501 2000 Up Yes 00:03:03:03:03:02
-------------------------------------------------------------------------------
*A:Dut-B# 

mrp

Syntax 
mrp
Context 
show>service>id
Description 

This command displays information on a a per service MRP configuration.

Output 

The following output is an example of service MRP information.

Sample Output
*A:PE-A# show service id 10 mrp
-------------------------------------------------------------------------------
MRP Information
-------------------------------------------------------------------------------
Admin State        : Up                 Failed Register Cnt: 0
Max Attributes     : 2048               Attribute Count    : 10
Flood Time         : Off
-------------------------------------------------------------------------------
*A:PE-A#

mrp-policy

Syntax 
mrp-policy [mrp-policy]
mrp-policy mrp-policy [association]
mrp-policy mrp-policy [entry entry-id]
Context 
show>service
Description 

This command displays MRP policy information.

Parameters 
mrp-policy—
Specifies the MRP policy.
Values—
32 chars max

 

entry-id—
Specifies the entry ID.
Values—
1 to 65535

 

association—
Displays associations for the specified MRP policy.

mmrp

Syntax 
mmrp mac [ieee-address]
Context 
show>service>id
Description 

This command displays information on MACs. If a MAC address is specified, information will be displayed relevant to the specific group. No parameter will display information on all group MACs on a server.

Parameters 
ieee-address—
Specifies a MAC address as a hex string in the form of xx:xx:xx:xx:xx:xx: or xx-xx-xx-xx-xx-xx
Output 

The following output is an example of service MRRP MAC information.

Sample Output
*A:PE-A# show service id 10 mmrp mac 01:1E:83:00:00:65
-------------------------------------------------------------------------------
SAP/SDP                                 MAC Address       Registered  Declared
-------------------------------------------------------------------------------
sap:1/1/4:10                            01:1e:83:00:00:65 No          Yes
sap:1/2/2:10                            01:1e:83:00:00:65 No          Yes
sap:2/2/5:10                            01:1e:83:00:00:65 Yes         Yes
-------------------------------------------------------------------------------
*A:PE-A#
 
*A:PE-A# show service id 10 mmrp mac
-------------------------------------------------------------------------------
SAP/SDP                                 MAC Address       Registered  Declared
-------------------------------------------------------------------------------
sap:1/1/4:10                            01:1e:83:00:00:65 No          Yes
sap:1/1/4:10                            01:1e:83:00:00:66 No          Yes
sap:1/1/4:10                            01:1e:83:00:00:67 No          Yes
sap:1/1/4:10                            01:1e:83:00:00:68 No          Yes
sap:1/1/4:10                            01:1e:83:00:00:69 No          Yes
sap:1/1/4:10                            01:1e:83:00:00:6a No          Yes
sap:1/1/4:10                            01:1e:83:00:00:6b No          Yes
sap:1/1/4:10                            01:1e:83:00:00:6c No          Yes
sap:1/1/4:10                            01:1e:83:00:00:6d No          Yes
sap:1/1/4:10                            01:1e:83:00:00:6e No          Yes
sap:1/2/2:10                            01:1e:83:00:00:65 No          Yes
sap:1/2/2:10                            01:1e:83:00:00:66 No          Yes
sap:1/2/2:10                            01:1e:83:00:00:67 No          Yes
sap:1/2/2:10                            01:1e:83:00:00:68 No          Yes
sap:1/2/2:10                            01:1e:83:00:00:69 No          Yes
sap:1/2/2:10                            01:1e:83:00:00:6a No          Yes
sap:1/2/2:10                            01:1e:83:00:00:6b No          Yes
sap:1/2/2:10                            01:1e:83:00:00:6c No          Yes
sap:1/2/2:10                            01:1e:83:00:00:6d No          Yes
sap:1/2/2:10                            01:1e:83:00:00:6e No          Yes
sap:2/2/5:10                            01:1e:83:00:00:65 Yes         Yes
sap:2/2/5:10                            01:1e:83:00:00:66 Yes         Yes
sap:2/2/5:10                            01:1e:83:00:00:67 Yes         Yes
sap:2/2/5:10                            01:1e:83:00:00:68 Yes         Yes
sap:2/2/5:10                            01:1e:83:00:00:69 Yes         Yes
sap:2/2/5:10                            01:1e:83:00:00:6a Yes         Yes
sap:2/2/5:10                            01:1e:83:00:00:6b Yes         Yes
sap:2/2/5:10                            01:1e:83:00:00:6c Yes         Yes
sap:2/2/5:10                            01:1e:83:00:00:6d Yes         Yes
sap:2/2/5:10                            01:1e:83:00:00:6e Yes         Yes
-------------------------------------------------------------------------------
*A:PE-A#

spb

Syntax 
spb
Context 
clear>service>id
Description 

This command clears STP related data.

adjacency

Syntax 
adjacency [detail]
Context 
show>service>id>spb
Description 

This command displays SPB adjacency information.

Parameters 
detail—
Shows detailed information
Output 

The following output is an example of service SPB adjacency information.

Sample Output
===============================================================================
ISIS Adjacency
===============================================================================
System ID                Usage State Hold Interface                     MT Enab
-------------------------------------------------------------------------------
Dut-B                    L1    Up    19   sap:1/2/2:1.1                 No
Dut-C                    L1    Up    21   sap:1/2/3:1.1                 No
-------------------------------------------------------------------------------
Adjacencies : 2
===============================================================================

base

Syntax 
base
Context 
show>service>id>spb
Description 

This command displays SPB base information.

Output 

The following output is an example of service SPB base information.

Sample Output
*A:Dut-A# show service id 100001 spb base
===============================================================================
Service SPB Information
===============================================================================
Admin State        : Up                 Oper State         : Up
ISIS Instance      : 1024               FID                : 1
Bridge Priority    : 8                  Fwd Tree Top Ucast : spf
Fwd Tree Top Mcast : st
Bridge Id          : 80:00.00:10:00:01:00:01
Mcast Desig Bridge : 80:00.00:10:00:01:00:01
 
===============================================================================
ISIS Interfaces
===============================================================================
Interface                        Level CircID  Oper State   L1/L2 Metric
-------------------------------------------------------------------------------
sap:1/2/2:1.1                    L1    65536   Up           10/-
sap:1/2/3:1.1                    L1    65537   Up           10/-
-------------------------------------------------------------------------------
Interfaces : 2
===============================================================================
FID ranges using ECT Algorithm
-------------------------------------------------------------------------------
1-99      low-path-id
100-100   high-path-id
101-4095  low-path-id
===============================================================================

database

Syntax 
database
Context 
show>service>id>spb
Description 

This command displays SPB database information.

Output 

The following output is an example of service SPB database information.

Sample Output
*A:Dut-A# show service id 100001 spb database
===============================================================================
ISIS Database
===============================================================================
LSP ID                                  Sequence  Checksum Lifetime Attributes
-------------------------------------------------------------------------------
 
Displaying Level 1 database
-------------------------------------------------------------------------------
Dut-A.00-00                             0xc       0xbaba   1103     L1
Dut-B.00-00                             0x13      0xe780   1117     L1
Dut-C.00-00                             0x13      0x85a    1117     L1
Dut-D.00-00                             0xe       0x174a   1119     L1
Level (1) LSP Count : 4
===============================================================================

fate-sharing

Syntax 
fate-sharing
Context 
show>service>id>spb
Description 

This command displays SPB fate-sharing information on User B-VPLS service, in correspond to associated Control B-VPLS service.

Output 

The following output is an example of service SPB fate sharing information.

Sample Output
*A:Dut-A# Node show service id spb fate-sharing
===============================================================================
User service fate-shared sap/sdp-bind information
===============================================================================
Control   Control Sap/             FID       User      User Sap/
SvcId     SdpBind                            SvcId     SdpBind
-------------------------------------------------------------------------------
500       1/1/20:500               502       502       1/1/20:502
===============================================================================

fdb

Syntax 
fdb
Context 
show>service>id>spb
Description 

This command displays SPB Forwarding database information (FDB).

Output 

The following output is an example of service SPB FDB information.

Sample Output
*A:Dut-A# show service id 100001 spb fdb
==============================================================================
User service FDB information
==============================================================================
MacAddr           UCast Source          State   MCast Source          State
------------------------------------------------------------------------------
00:10:00:01:00:02 1/2/2:1.1             ok      1/2/2:1.1             ok
00:10:00:01:00:03 1/2/3:1.1             ok      1/2/3:1.1             ok
00:10:00:01:00:04 1/2/2:1.1             ok      1/2/2:1.1             ok
------------------------------------------------------------------------------
Entries found: 3
==============================================================================

fid

Syntax 
fid [fid] fate-sharing
fid [fid] user-service
fid [fid] fdb
fid [fid] mfib [group-mac ieee-address]
fid [fid] mfib [isid isid]
Context 
show>service>id>spb
Description 

This command displays SPB control service FID information.

Parameters 
fid—
A user service FID may be specified. All user service FIDs are displayed if the FID is not specified.
Values—
1 to 4095

 

fate-sharing—
Displays fate-sharing information
user-service—
Specifies user VPLS information for each control VPLS per forwarding data-base identifier. A user service FID may be specified. All user service FIDs are displayed if the FID is not specified.
fdb—
Displays forwarding database (FDB) information
mfib—
Displays multicast forwarding information base (MFIB) information
ieee-address—
Specifies the 48-bit IEEE 802.3 group MAC address
isid—
Specifies the value of ISID of the group MAC address of this entry
Values—
0 to 16777215

 

Output 

The following output is an example of service SPB FID fare sharing information.

Sample Output
*A:Dut-A# show service id 100001 spb fid fate-sharing
===============================================================================
Control service fate-shared sap/sdp-bind information
===============================================================================
Control   Control Sap/             FID       User      User Sap/
SvcId     SdpBind                            SvcId     SdpBind
-------------------------------------------------------------------------------
500       1/1/20:500               502       502       1/1/20:502
=============================================================================== 
 
*A:Dut-A# show service id 100001 spb fid fdb
===============================================================================
Control service FDB information
===============================================================================
Fid        MacAddr            UCast Source             MCast Source
                              Last Update              Last Update
-------------------------------------------------------------------------------
1          00:10:00:01:00:01  local                    local
                              04/04/2012 15:11:24      04/04/2012 15:11:24
1          00:10:00:01:00:02  1/2/2:1.1                1/2/2:1.1
                              04/04/2012 15:51:45      04/04/2012 15:51:45
1          00:10:00:01:00:03  1/2/3:1.1                1/2/3:1.1
                              04/04/2012 15:51:56      04/04/2012 15:51:56
1          00:10:00:01:00:04  1/2/2:1.1                1/2/2:1.1
                              04/04/2012 15:52:11      04/04/2012 15:52:11
-------------------------------------------------------------------------------
Entries found: 4
===============================================================================
*A:Dut-A# show service id 100001 spb fid mfib
===============================================================================
Control service MFIB information
===============================================================================
FID   MacAddr           ISID      Source                   Last Update
-------------------------------------------------------------------------------
1     01:1E:83:00:27:11 10001     1/2/2:1.1                04/04/2012 15:51:45
                                  1/2/3:1.1                04/04/2012 15:51:56
                                  local                    04/04/2012 15:42:44
100   01:1E:83:00:27:12 10002     1/2/2:1.1                04/04/2012 15:51:45
                                  1/2/3:1.1                04/04/2012 15:51:56
                                  local                    04/04/2012 15:43:09
-------------------------------------------------------------------------------
Entries found: 6
===============================================================================

hostname

Syntax 
hostname
Context 
show>service>id>spb
Description 

This command displays SPB system-id to hostname mapping.

Output 

The following output is an example of service SPB hostname information.

Sample Output
*A:Dut-A# show service id 100001 spb hostname
===============================================================================
Hosts
===============================================================================
System Id                Hostname
-------------------------------------------------------------------------------
0000.00AA.AAAA           cses-B02
0000.00BB.BBBB           cses-B07
===============================================================================

interface

Syntax 
interface
Context 
show>service>id>spb
Description 

This command displays SPB interfaces.

Output 

The following output is an example of service SPB interface information.

Sample Output
*A:Dut-A# show service id 100001 spb interface
===============================================================================
ISIS Interfaces
===============================================================================
Interface                        Level CircID  Oper State   L1/L2 Metric
-------------------------------------------------------------------------------
sap:1/1/20:500                   L1    65536   Up           10/-
-------------------------------------------------------------------------------
Interfaces : 1
===============================================================================

mfib

Syntax 
mfib [group-mac ieee-address] [isid isid]
Context 
show>service>id>spb
Description 

This command displays multicast forwarding data-base (MFIB) information.

Parameters 
ieee-address—
Specifies a MAC address
Values—
xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx

 

isid —
Specifies an I-SID
Values—
0 to 16777215

 

Output 

The following output is an example of service SPB MFIB information.

Sample Output
*A:Dut-A# show service id 100001 spb mfib
===============================================================================
User service MFIB information
===============================================================================
MacAddr           ISID     Status
-------------------------------------------------------------------------------
01:1E:83:00:27:11 10001    Ok
-------------------------------------------------------------------------------
Entries found: 1
===============================================================================

routes

Syntax 
routes
Context 
show>service>id>spb
Description 

This command displays SPB route information.

Output 

The following output is an example of service SPB route information.

Sample Output
*A:Dut-A# show service id 100001 spb routes
================================================================
MAC Route Table
================================================================
Fid  MAC                                          Ver.   Metric
      NextHop If                    SysID
----------------------------------------------------------------
 
Fwd Tree: unicast
----------------------------------------------------------------
1    00:10:00:01:00:02                            10     10
      sap:1/2/2:1.1                 Dut-B
1    00:10:00:01:00:03                            10     10
      sap:1/2/3:1.1                 Dut-C
1    00:10:00:01:00:04                            10     20
      sap:1/2/2:1.1                 Dut-B
100  00:10:00:02:00:02                            10     10
      sap:1/2/2:1.1                 Dut-B
100  00:10:00:02:00:03                            10     10
      sap:1/2/3:1.1                 Dut-C
100  00:10:00:02:00:04                            10     20
      sap:1/2/3:1.1                 Dut-C
 
Fwd Tree: multicast
----------------------------------------------------------------
1    00:10:00:01:00:02                            10     10
      sap:1/2/2:1.1                 Dut-B
1    00:10:00:01:00:03                            10     10
      sap:1/2/3:1.1                 Dut-C
1    00:10:00:01:00:04                            10     20
      sap:1/2/2:1.1                 Dut-B
100  00:10:00:02:00:02                            10     10
      sap:1/2/2:1.1                 Dut-B
100  00:10:00:02:00:03                            10     10
      sap:1/2/3:1.1                 Dut-C
100  00:10:00:02:00:04                            10     20
      sap:1/2/3:1.1                 Dut-C
----------------------------------------------------------------
No. of MAC Routes: 12
================================================================
 
================================================================
ISID Route Table
================================================================
Fid  ISID                                         Ver.
      NextHop If                    SysID
----------------------------------------------------------------
1    10001                                        10
      sap:1/2/2:1.1                 Dut-B
      sap:1/2/3:1.1                 Dut-C
100  10002                                        10
      sap:1/2/2:1.1                 Dut-B
      sap:1/2/3:1.1                 Dut-C
----------------------------------------------------------------
No. of ISID Routes: 2
================================================================ 
A:Dut-A#  show service id spb fate-sharing
===============================================================================
User service fate-shared sap/sdp-bind information
===============================================================================
Control   Control Sap/             FID       User      User Sap/
SvcId     SdpBind                            SvcId     SdpBind
-------------------------------------------------------------------------------
500       1/1/20:500               502       502       1/1/20:502
===============================================================================

spf

Syntax 
spf
Context 
show>service>id>spb
Description 

This command displays SPF information.

Output 

The following output is an example of service SPB SPF information.

Sample Output
A:cses-B01#  show service id spb spf
===============================================================================
Path Table
===============================================================================
Node                            Interface                  Nexthop
-------------------------------------------------------------------------------
 
Fwd Tree: unicast,   ECT Alg: low-path-id
-------------------------------------------------------------------------------
cses-B07.00                     sap:1/1/20:500             cses-B07
cses-B01.00                  sap:1/1/20:500             cses-B07
cses-B07.00                     sap:1/1/20:500             cses-B07
 
Fwd Tree: unicast,   ECT Alg: high-path-id
-------------------------------------------------------------------------------
cses-B07.00                     sap:1/1/20:500             cses-B07
cses-B01.00                 sap:1/1/20:500             cses-B07
cses-B07.00                     sap:1/1/20:500             cses-B07
 
Fwd Tree: multicast,   ECT Alg: low-path-id
-------------------------------------------------------------------------------
cses-B07.00                     sap:1/1/20:500             cses-B07
cses-B01.00                  sap:1/1/20:500             cses-B07
cses-B07.00                     sap:1/1/20:500             cses-B07
 
Fwd Tree: multicast,   ECT Alg: high-path-id
-------------------------------------------------------------------------------
cses-B07.00                     sap:1/1/20:500             cses-B07
cses-B01.00                 sap:1/1/20:500             cses-B07
cses-B07.00                     sap:1/1/20:500             cses-B07
===============================================================================

spf-log

Syntax 
spf-log
Context 
show>service>id>spb
Description 

This command displays SPF Log information.

Output 

The following output is an example of service SPB SPF log information.

Sample Output
A:cses-B01#  show service id spb spf-log
===============================================================================
ISIS SPF Log
===============================================================================
When                 Duration       L1 Nodes   L2 Nodes   Event Count      Type
-------------------------------------------------------------------------------
07/23/2012 16:01:13  <0.01s         1          0          1                Reg
07/23/2012 16:01:19  <0.01s         1          0          4                Reg
07/23/2012 16:01:24  <0.01s         3          0          2                Reg
07/23/2012 16:01:29  <0.01s         4          0          1                Reg
-------------------------------------------------------------------------------
Log Entries : 4
-------------------------------------------------------------------------------

statistics

Syntax 
statistics
Context 
show>service>id>spb
Description 

This command displays SPB statistics.

Output 

The following output is an example of service SPB statistics information.

Sample Output
A:cses-B01#  show service id spb statistics
===============================================================================
ISIS Statistics
===============================================================================
ISIS Instance     : 1024                    SPF Runs       : 4
Purge Initiated   : 0                       LSP Regens.    : 11
 
CSPF Statistics
Requests          : 0                       Request Drops  : 0
Paths Found       : 0                       Paths Not Found: 0
 
-------------------------------------------------------------------------------
PDU Type   Received   Processed  Dropped    Sent       Retransmitted
-------------------------------------------------------------------------------
LSP        31         31         0          9          0
IIH        532        532        0          533        0
CSNP       479        479        0          479        0
PSNP       9          9          0          27         0
Unknown    0          0          0          0          0
===============================================================================

status

Syntax 
status
Context 
show>service>id>spb
Description 

This command displays SPB status.

Output 

The following output is an example of service SPB status information.

Sample Output
A:cses-B01#  show service id spb status
===============================================================================
ISIS Status
===============================================================================
System Id            : 0000.00AA.AAAA
Admin State          : Up
Oper State           : Up
SPB Routing          : Enabled
Last Enabled         : 07/23/2012 16:01:06
Level Capability     : L1
Authentication Check : True
Authentication Type  : None
CSNP-Authentication  : Enabled
HELLO-Authentication : Enabled
PSNP-Authentication  : Enabled
Overload-On-Boot Tim*: 0
LSP Lifetime         : 1200
LSP Wait             : 5 sec (Max)   0 sec (Initial)   1 sec (Second)
LSP MTU Size         : 1492  (Config)  1492  (Oper)
Adjacency Check      : loose
L1 Auth Type         : none
L1 CSNP-Authenticati*: Enabled
L1 HELLO-Authenticat*: Enabled
L1 PSNP-Authenticati*: Enabled
L1 Preference        : 15
L1 Ext. Preference   : 160
L1 Wide Metrics      : Enabled
L1 LSDB Overload     : Disabled
L1 LSPs              : 4
L1 Default Metric    : 10
L1 IPv6 Def Metric   : 10
Last SPF             : 07/23/2012 16:01:29
SPF Wait             : 10 sec (Max)   1000 ms (Initial)   1000 ms (Second)
Multi-topology       : Disabled
Area Addresses       : 00
Total Exp Routes(L1) : 0
IID TLV              : Disabled
All-L1-MacAddr       : 01:80:c2:00:00:14
=============================================================================== 

4.6.2.2. PBB Clear Commands

counters

Syntax 
counters
Context 
clear>service>statistics>id
Description 

This command clears all traffic queue counters associated with the service ID.

mesh-sdp

Syntax 
mesh-sdp sdp-id[:vc-id] {all | counters |stp | mrp}
Context 
clear>service>statistics>id
Description 

This command clears the statistics for a particular mesh SDP bind.

Parameters 
sdp-id—
Specifies the SDP ID for which to display information
Default—
All SDPs.
Values—
1 to 17407

 

vc-id—
Displays information about the virtual circuit identifier.
Values—
1 to 4294967295

 

all—
Clears all queue statistics and STP statistics associated with the SDP
counters—
Clears all queue statistics associated with the SDP
stp—
Clears all STP statistics associated with the SDP
mrp—
Clears all MRP statistics associated with the SDP

mrp

Syntax 
mrp
Context 
clear>service>statistics>id
Description 

This command clears all MRP statistics for the service ID.

spoke-sdp

Syntax 
spoke-sdp sdp-id[:vc-id] {all | counters | stp| l2pt | mrp}
Context 
clear>service>statistics>id
Description 

This command clears statistics for the spoke SDP bound to the service.

Parameters 
sdp-id—
The spoke SDP ID for which to clear statistics
Values—
1 to 17407

 

vc-id—
The virtual circuit ID on the SDP ID to be reset
Values—
1 to 4294967295

 

all—
Clears all queue statistics and STP statistics associated with the SDP
counters—
Clears all queue statistics associated with the SDP
stp—
Clears all STP statistics associated with the SDP
l2pt—
Clears all L2PT statistics associated with the SDP
mrp—
Clears all MRP statistics associated with the SDP

sap

Syntax 
sap sap-id {all | counters | stp| l2pt | mrp}
Context 
clear>service>statistics>id
Description 

This command clears statistics for the SAP.

Parameters 
sap-id—
The SAP ID for which to clear statistics
all—
Clears all queue statistics and STP statistics associated with the SAP
counters—
Clears all queue statistics associated with the SAP
stp—
Clears all STP statistics associated with the SAP
l2pt—
Clears all L2PT statistics associated with the SAP
mrp—
Clears all MRP statistics associated with the SAP

stp

Syntax 
stp
Context 
clear>service>statistics>id
Description 

Clears all spanning tree statistics for the service ID.

4.6.2.3. PBB Debug Commands

mrp

Syntax 
[no] mrp
Context 
debug>service>id
Description 

This command enables and configures MRP debugging.

all-events

Syntax 
all-events
Context 
debug>service>id>mrp
Description 

This command enables MRP debugging for the applicant, leave all, periodic and registrant state machines and enables debugging of received and transmitted MRP PDUs.

applicant-sm

Syntax 
[no] applicant-sm
Context 
debug>service>id>mrp
Description 

This command enables debugging of the applicant state machine.

The no form of the command disables debugging of the applicant state machine.

leave-all-sm

Syntax 
[no] leave-all-sm
Context 
debug>service>id>mrp
Description 

This command enables debugging of the leave all state machine.

The no form of the command disables debugging of the leave all state machine.

mmrp-mac

Syntax 
[no] mmrp-mac ieee-address
Context 
debug>service>id>mrp
Description 

This command filters debug events and only shows events related to the MAC address specified.

The no form of the command removes the debug filter.

Parameters 
ieee-address—
xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx (cannot be all zeros)

mrpdu

Syntax 
[no] mrpdu
Context 
debug>service>id>mrp
Description 

This command enables debugging of the MRP PDUs that are received or transmitted.

The no form of the command disables debugging of MRP PDUs.

periodic-sm

Syntax 
[no] periodic-sm
Context 
debug>service>id>mrp
Description 

This command enables debugging of the periodic state machine.

The no form of the command disables debugging of the periodic state machine.

registrant-sm

Syntax 
[no] registrant-sm
Context 
debug>service>id>mrp
Description 

This command enables debugging of the registrant state machine.

The no form of the command disables debugging of the registrant state machine.

sap

Syntax 
[no] sap sap-id
Context 
debug>service>id>mrp
Description 

This command filters debug events and only shows events for the particular SAP.

The no form of the command removes the debug filter.

Parameters 
sap-id—
The SAP ID.

sdp

Syntax 
[no] sdp sdp-id:vc-id
Context 
debug>service>id>mrp
Description 

This command filters debug events and only shows events for the particular SDP.

The no form of the command removes the debug filter.

Parameters 
sdp-id—
Specifies the SDP ID for which to display information
Default—
All SDPs
Values—
1 to 17407

 

vc-id—
Displays information about the virtual circuit identifier.
Values—
1 to 4294967295