The use and configuration of EVPN-VPWS services is described in EVPN-VPWS for VXLAN tunnels with the following differences when the EVPN-VPWS services use MPLS tunnels instead of VXLAN.
When MPLS tunnels are used, the bgp-evpn>mpls context must be configured in the Epipe. As an example, if Epipe 2 is an EVPN-VPWS service that uses MPLS tunnels between PE2 and PE4, this would be its configuration:
PE2>config>service>epipe(2)#
-----------------------
bgp
exit
bgp-evpn
evi 2
local-attachment-circuit "AC-1"
eth-tag 200
exit
remote-attachment-circuit "AC-2"
eth-tag 200
exit
mpls bgp 1
ecmp 2
no shutdown
exit
sap 1/1/1:1 create
PE4>config>service>epipe(2)#
-----------------------
bgp
exit
bgp-evpn
evi 2
local-attachment-circuit "AC-2"
eth-tag 200
exit
remote-attachment-circuit "AC-1"
eth-tag 100
exit
mpls bgp 1
ecmp 2
no shutdown
exit
spoke-sdp 1:1
Where the following BGP-EVPN commands, specific to MPLS tunnels, are supported in the same way as in VPLS services:
mpls auto-bind-tunnel
mpls control-word
mpls entropy-label
mpls force-vlan-vc-forwarding
mpls shutdown
EVPN-VPWS Epipes with MPLS tunnels can also be configured with the following characteristics.
Access attachment circuits can be SAPs or spoke SDPs. Manually configured and BGP-VPWS spoke SDPs are supported. The VC switching configuration is not supported on BGP-EVPN-enabled pipes.
EVPN-VPWS Epipes using null SAPs can be configured with sap>ethernet>llf. When enabled, upon removing the EVPN destination, the port is brought oper-down with flag LinkLossFwd, however the AD per EVI route for the SAP is still advertised (the SAP is kept oper-up). When the EVPN destination is created, the port is brought oper-up and the flag cleared.
EVPN-VPWS Epipes for MPLS tunnels support endpoints. The parameter endpoint endpoint name is configurable along with bgp-evpn>local-attachment-circuit and bgp-evpn>remote-attachment-circuit. The following conditions apply to endpoints on EVPN-VPWS Epipes with MPLS tunnels.
Up to two explicit endpoints are allowed per Epipe service with BGP-EVPN configured.
A limited endpoint configuration is allowed in Epipes with BGP-EVPN. Specifically, neither active-hold-delay nor revert-time are configurable.
When bgp-evpn>remote-attachment-circuit is added to an explicit endpoint with a spoke SDP, the spoke-sdp>precedence command is not allowed. The spoke SDP always has a precedence of four, which is always higher than the EVPN precedence. Therefore, the EVPN-MPLS destination is used for transmission if it is created, and the spoke SDP is only used when the EVPN-MPLS destination is removed.
EVPN-VPWS Epipes for MPLS tunnels support control word and entropy labels. When a control word is configured, the PE sets the C bit in its AD per-EVI advertisement and sends the control word in the data path. In this case, the PE expects the control word to be received. If there is a mismatch between the received control word and the configured control word, the system does not set up the EVPN destination; as a result, the service does not come up.
EVPN-VPWS Epipes support force-qinq-vc-forwarding [c-tag-c-tag | s-tag-c-tag] under bgp-evpn>mpls and qinq-vlan-translation s-tag.c-tag on ingress QinQ SAPs.
When QinQ VLAN translation is configured at the ingress QinQ SAP, the service-delimiting outer and inner VLAN values can be translated to the configured values. The command force-qinq-vc-forwarding s-tag-c-tag must be configured to preserve the translated QinQ tags in the payload when sending EVPN packets. This translation and preservation behavior is aligned with the ‟normalization” concept described in draft-ietf-bess-evpn-vpws-fxc. The VLAN tag processing described in Epipe service pseudowire VLAN tag processing applies to EVPN destinations in EVPN-VPWS services too.
The following features, described in EVPN-VPWS for VXLAN tunnels, are also supported for MPLS tunnels:
Advertisement of the Layer-2 MTU and consistency checking of the MTU of the AD per-EVI routes.
Use of A/S PW and MC-LAG at access.
EVPN multihoming, including:
Single-active and all-active
Regular or virtual ESs
All existing DF election modes