Non-system IPv4 and IPv6 VXLAN termination in VPLS, R-VPLS, and Epipe services

Prerequisites

By default, only VXLAN packets with the same IP destination address as the system IPv4 address of the router can be terminated and processed for a subsequent MAC lookup. A router can simultaneously terminate VXLAN tunnels destined for its system IP address and three additional non-system IPv4 or IPv6 addresses, which can be on the base router or VPRN instances. This section describes the configuration requirements for services to terminate VXLAN packets destined for a non-system loopback IPv4 or IPv6 address on the base router or VPRN.

About this task

Perform the following steps to configure a service with non-system IPv4 or IPv6 VXLAN termination:

Procedure

Create the FPE (see FPE Creation)
Associate the FPE with VXLAN termination (see FPE Association with VXLAN Termination)
Configure the router loopback interface (see VXLAN Router Loopback Interface)
Configure VXLAN termination (non-system) VTEP addresses (see VXLAN Termination VTEP Addresses)
Add the service configuration (see VXLAN Services)

What to do next

The following actions must be considered when the aforementioned steps are completed.

FPE Creation

A Forwarding Path Extension (FPE) is required to terminate non-system IPv4 or IPv6 VXLAN tunnels.

In a non-system IPv4 VXLAN termination, the FPE function is used for additional processing required at ingress (VXLAN tunnel termination) only, and not at egress (VXLAN tunnel origination).

If the IPv6 VXLAN terminates on a VPLS or Epipe service, the FPE function is used at ingress only, and not at egress.

For R-VPLS services terminating IPv6 VXLAN tunnels and also for VPRN VTEPs, the FPE is used for the egress as well as the VXLAN termination function. In the case of R-VPLS, an internal static SDP is created to allow the required extra processing.

For information about FPE configuration and functions, see the 7450 ESS, 7750 SR, 7950 XRS, and VSR Interface Configuration Guide, "Forwarding Path Extension".
FPE Association with VXLAN Termination

The FPE must be associated with the VXLAN termination application. The following example configuration shows two FPEs and their corresponding association. FPE 1 uses the base router and FPE 2 is configured for VXLAN termination on VPRN 10.
```
configure
   fwd-path-ext
       fpe 1 create
             path pxc pxc-1
             vxlan-termination
       fpe 2 create
             path pxc pxc-2
             vxlan-termination router 10
```
VXLAN Router Loopback Interface

Create the interface that terminates and originates the VXLAN packets. The interface is created as a router interface, which is added to the Interior Gateway Protocol (IGP) and used by the BGP as the EVPN NLRI next hop.

Because the system cannot terminate the VXLAN on a local interface address, a subnet must be assigned to the loopback interface and not a host IP address that is /32 or /128. In the following example, all the addresses in subnet 11.11.11.0/24 (except 11.11.11.1, which is the interface IP) and subnet 10.1.1.0/24 (except 10.1.1.1) can be used for tunnel termination. The subnet is advertised using the IGP and is configured on either the base router or a VPRN. In the example, two subnets are assigned, in the base router and VPRN 10 respectively.
```
configure 
  router 
       interface "lo1"
            loopback
            address 10.11.11.1/24 
       isis
            interface "lo1"
                 passive
                 no shutdown
```
```
configure
    service
        vprn 10 name "vprn10" customer 1 create
            interface "lo1"
                loopback
                address 10.1.1.1/24
            isis 
                interface "lo1" 
                    passive 
                    no shutdown 
```
A local interface address cannot be configured as a VXLAN tunnel-termination IP address in the CLI, as shown in the following example.
```
*A:PE-3# configure service system vxlan tunnel-termination 192.0.2.3 fpe 1 create
MINOR: SVCMGR #8353 VXLAN Tunnel termination IP address cannot be configured -
 IP address in use by another application or matches a local interface IP address
```
The subnet can be up to 31 bits. For example, to use 10.11.11.1 as the VXLAN termination address, the subnet should be configured and advertised as shown in the following example configuration.
```
 interface "lo1"
            address 10.11.11.0/31
            loopback
            no shutdown
        exit
        isis 0
            interface "lo1"
                passive
                no shutdown
            exit
            no shutdown
        exit
```
It is not a requirement for the remote PEs and NVEs to have the specific /32 or /128 IP address in their RTM to resolve the BGP EVPN NLRI next hop or forward the VXLAN packets. An RTM with a subnet that contains the remote VTEP can also perform these tasks.
Note: The system does not check for a pre-existing local base router loopback interface with a subnet corresponding to the VXLAN tunnel termination address. If a tunnel termination address is configured and the FPE is operationally up, the system starts terminating VXLAN traffic and responding ICMP messages for that address. The following conditions are ignored in this scenario:
- the presence of a loopback interface in the base router
- the presence of an interface with the address contained in the configured subnet, and no loopback
The following example output includes an IPv6 address in the base router. It could also be configured in a VPRN instance.
```
configure 
  router 
      interface "lo1" 
           loopback
           address 10.11.11.1/24 
           ipv6
               address 2001:db8::/127
           exit
      isis
           interface "lo1"
               passive
               no shutdown
```

VXLAN Termination VTEP Addresses

The service>system>vxlan>tunnel-termination context allows the user to configure non-system IP addresses that can terminate the VXLAN and their corresponding FPEs.

As shown in the following example, an IP address may be associated with a new or existing FPE already terminating the VXLAN. The list of addresses that can terminate the VXLAN can include IPv4 and IPv6 addresses.

config service system vxlan# 
       tunnel-termination 10.11.11.1 fpe 1 create
       tunnel-termination 2001:db8:1000::1 fpe 1 create 
        
config service vprn 10 vxlan# 
       tunnel-termination 10.1.1.2 fpe 2 create

The tunnel-termination command creates internal loopback interfaces that can respond to ICMP requests. In the following sample output, an internal loopback is created when the tunnel termination address is added (for 10.11.11.1 and 2001:db8:1000::1). The internal FPE router interfaces created by the VXLAN termination function are also shown in the output. Similar loopback and interfaces are created for tunnel termination addresses in a VPRN (not shown).

*A:PE1# show router interface 
===============================================================================
Interface Table (Router: Base)
===============================================================================
Interface-Name                   Adm       Opr(v4/v6)  Mode    Port/SapId
   IP-Address                                                  PfxState
-------------------------------------------------------------------------------
_tmnx_fpe_1.a                    Up        Up/Up       Network pxc-2.a:1
   fe80::100/64                                                PREFERRED
_tmnx_fpe_1.b                    Up        Up/Up       Network pxc-2.b:1
   fe80::101/64                                                PREFERRED
_tmnx_vli_vxlan_1_131075         Up        Up/Up       Network loopback
   10.11.11.1/32                                               n/a
   2001:db8:1000::1                                            PREFERRED
   fe80::6cfb:ffff:fe00:0/64                                   PREFERRED
lo1                              Up        Up/Down     Network loopback
   10.11.11.0/31                                               n/a
system                           Up        Up/Down     Network system
   1.1.1.1/32                                                  n/a
<snip>

VXLAN Services

By default, the VXLAN services use the system IP address as the source VTEP of the VXLAN encapsulated frames. The vxlan-src-vtep command in the config>service>vpls or config>service>epipe context enables the system to use a non-system IPv4 or IPv6 address as the source VTEP for the VXLAN tunnels in that service.

A different vxlan-src-vtep can be used for different services, as shown in the following example where two different services use different non-system IP addresses as source VTEPs.
```
configure service vpls 1 
   vxlan-src-vtep 10.11.11.1
 
configure service vpls 2
   vxlan-src-vtep 2001:db8:1000::1
```
In addition, if a vxlan-src-vtep is configured and the service uses EVPN, the IP address is also used to set the BGP NLRI next hop in EVPN route advertisements for the service.
Note:
The BGP EVPN next hop can be overridden by the use of export policies based on the following rules.
- A BGP peer policy can override a next hop pushed by the vxlan-src-vtep configuration.
- If the VPLS service is IPv6 (that is, the vxlan-src-vtep is IPv6) and a BGP peer export policy is configured with next-hop-self, the BGP next-hop is overridden with an IPv6 address auto-derived from the IP address of the system. The auto-derivation is based on RFC 4291. For example, ::ffff:10.20.1.3 is auto-derived from system IP 10.20.1.3.
- The policy checks the address type of the next hop provided by the vxlan-src-vtep command. If the command provides an IPv6 next hop, the policy is unable use an IPv4 address to override the IPv6 address provided by the vxlan-src-vtep command.
After the preceding steps are performed to configure a VXLAN termination, the VPLS, R-VPLS, or Epipe service can be used normally, except that the service terminates VXLAN tunnels with a non-system IPv4 or IPv6 destination address (in the base router or a VPRN instance) instead of the system IP address only.

The FPE vxlan-termination function creates internal router interfaces and loopbacks that are displayed by the show commands. When configuring IPv6 VXLAN termination on an R-VPLS service, as well as the internal router interfaces and loopbacks, the system creates internal SDP bindings for the required egress processing. The following output shows an example of an internal FPE-type SDP binding created for IPv6 R-VPLS egress processing.
```
*A:PE1# show service sdp-using  
===============================================================================
SDP Using
===============================================================================
SvcId      SdpId              Type   Far End              Opr   I.Label E.Label
                                                          State         
-------------------------------------------------------------------------------
2002       17407:2002         Fpe    fpe_1.b              Up    262138  262138
-------------------------------------------------------------------------------
Number of SDPs : 1
-------------------------------------------------------------------------------
===============================================================================
```
When BGP EVPN is used, the BGP peer over which the EVPN-VXLAN updates are received can be an IPv4 or IPv6 peer, regardless of whether the next-hop is an IPv4 or IPv6 address.

The same VXLAN tunnel termination address cannot be configured on different router instances; that is, on two different VPRN instances or on a VPRN and the base router.