Enter the fwd-path-ext context
16.0.R1
All
Enter the fpe list instance
configure fwd-path-ext fpe number
16.0.R1
All
FPE ID
configure fwd-path-ext fpe number
1 to 64
This element is part of a list key.
16.0.R1
All
Enter the application context
configure fwd-path-ext fpe number application
16.0.R1
All
Use FPE to set up FPE PW cross-connect
configure fwd-path-ext fpe number application pw-port boolean
false
16.0.R1
All
Enable the srv6 context
configure fwd-path-ext fpe number application srv6
21.5.R1
7450 ESS, 7750 SR, 7750 SR-s, 7950 XRS, VSR
Enter the interface-a context
Commands in this context configure the parameters of network interface-a of the SRv6 FPE.
21.5.R2
7450 ESS, 7750 SR, 7750 SR-s, 7950 XRS, VSR
Enter the qos context
21.5.R2
7450 ESS, 7750 SR, 7750 SR-s, 7950 XRS, VSR
Network QoS policy applied to the SRv6 FPE interfaces
configure fwd-path-ext fpe number application srv6 interface-a qos network-policy reference
21.5.R2
7450 ESS, 7750 SR, 7750 SR-s, 7950 XRS, VSR
Enter the interface-b context
Commands in this context configure the parameters of network interface-b of the SRv6 FPE.
21.5.R2
7450 ESS, 7750 SR, 7750 SR-s, 7950 XRS, VSR
MTU size of SRv6 origination FPE interface-b
configure fwd-path-ext fpe number application srv6 interface-b mtu number
This command configures the Maximum Transfer Unit (MTU) of interface-b of the SRv6 origination FPE.
The MTU is used to check if an IPv4 service packet should be fragmented and if an IPv6 service packet should be dropped when tunneled over SRv6.
The minimum value is the IPv6 minimum MTU value. The maximum value is set to the FP4 maximum Ethernet port MTU (9800) minus 14 bytes for Null Ethernet encapsulation.
0 | 1280 to 9786
21.5.R2
7450 ESS, 7750 SR, 7750 SR-s, 7950 XRS, VSR
Enter the qos context
21.5.R2
7450 ESS, 7750 SR, 7750 SR-s, 7950 XRS, VSR
Network QoS policy applied to the SRv6 FPE interfaces
configure fwd-path-ext fpe number application srv6 interface-b qos network-policy reference
21.5.R2
7450 ESS, 7750 SR, 7750 SR-s, 7950 XRS, VSR
SRv6 FPE application type
configure fwd-path-ext fpe number application srv6 type keyword
This command specifies if the SRv6 FPE application is used for origination or termination of SRv6 tunnels.
A dedicated SRv6 FPE is required for origination and termination of SRv6 tunnels on services and they cannot share the same FPE.
A single FPE can be configured for SRv6 origination. One or more FPEs can be configured for SRv6 termination, where a termination SRv6 FPE is assigned one or more configured locators.
Transit SRv6 routers do not require SRv6 FPEs.
origination, termination
21.5.R1
7450 ESS, 7750 SR, 7750 SR-s, 7950 XRS, VSR
Reserve FPE for hybrid access bonding
configure fwd-path-ext fpe number application sub-mgmt-extension boolean
false
16.0.R1
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Enable the vxlan-termination context
16.0.R1
All
Router name or VPRN service name
configure fwd-path-ext fpe number application vxlan-termination router-instance string
Base
16.0.R1
All
Text description
configure fwd-path-ext fpe number description string
1 to 80
16.0.R1
All
Enter the path context
configure fwd-path-ext fpe number path
16.0.R1
All
Cross connect port ID
configure fwd-path-ext fpe number path pxc reference
The following are part of a choice: pxc or (xc-lag-a and xc-lag-b).
16.0.R1
All
LAG name
configure fwd-path-ext fpe number path xc-lag-a reference
The following are part of a choice: pxc or (xc-lag-a and xc-lag-b).
16.0.R4
All
LAG name
configure fwd-path-ext fpe number path xc-lag-b reference
The following are part of a choice: pxc or (xc-lag-a and xc-lag-b).
16.0.R4
All
Enable the sdp-id-range context
16.0.R1
All
Upper bound of the SDP ID range
configure fwd-path-ext sdp-id-range end number
1 to 32767
This element is mandatory.
16.0.R1
All
Lower bound of the SDP ID range
configure fwd-path-ext sdp-id-range start number
1 to 32767
This element is mandatory.
16.0.R1
All