All-active multihoming service model

The following shows an example PE1 configuration that provides all-active multihoming to the CE2 shown in Figure: Aliasing .

*A:PE1>config>lag(1)# info 
----------------------------------------------
  mode access
  encap-type dot1q
  port 1/1/2
  lacp active administrative-key 1 system-id 00:00:00:00:00:22
  no shutdown

*A:PE1>config>service>system>bgp-evpn# info 
----------------------------------------------
  route-distinguisher 10.1.1.1:0
  ethernet-segment "ESI2" create
    esi 01:12:12:12:12:12:12:12:12:12
    multi-homing all-active
    service-carving
    lag 1 
    no shutdown

*A:PE1>config>redundancy>evpn-multi-homing# info 
----------------------------------------------
    boot-timer 120
    es-activation-timer 10

*A:PE1>config>service>vpls# info 
----------------------------------------------
  description "evpn-mpls-service with all-active multihoming"
  bgp
  bgp-evpn
    evi 10
    mpls bgp 1
      no shutdown
      auto-bind-tunnel resolution any
  sap lag-1:1 create 
  exit

In the same way, PE2 is configured as follows:

*A:PE1>config>lag(1)# info 
----------------------------------------------
  mode access
  encap-type dot1q
  port 1/1/1
  lacp active administrative-key 1 system-id 00:00:00:00:00:22
  no shutdown

*A:PE1>config>service>system>bgp-evpn# info 
----------------------------------------------
  route-distinguisher 10.1.1.1:0
  ethernet-segment "ESI12" create
    esi 01:12:12:12:12:12:12:12:12:12
    multi-homing all-active
    service-carving
    lag 1 
    no shutdown

*A:PE1>config>redundancy>evpn-multi-homing# info 
----------------------------------------------
    boot-timer 120
    es-activation-timer 10

*A:PE1>config>service>vpls# info 
----------------------------------------------
  description "evpn-mpls-service with all-active multihoming"
  bgp
    route-distinguisher 65001:60
    route-target target:65000:60
  bgp-evpn
    evi 10
    mpls bgp 1
      no shutdown
      auto-bind-tunnel resolution any
  sap lag-1:1 create 
  exit

The preceding configuration enables the all-active multihoming procedures. The following must be considered:

• The ethernet-segment must be configured with a name and a 10-byte esi:

  • config>service>system>bgp-evpn# ethernet-segment<es_name> create

  • config>service> system>bgp-evpn>ethernet-segment# esi <value>

• When configuring the esi, the system enforces the 6 high-order octets after the type to be different from zero (so that the auto-derived route-target for the ES route is different from zero). Other than that, the entire esi value must be unique in the system.

• Only a LAG or a PW port can be associated with the all-active ethernet-segment. This LAG is exclusively used for EVPN multihoming. Other LAG ports in the system can be still used for MC-LAG and other services.

• When the LAG is configured on PE1 and PE2, the same admin-key, system-priority, and system-id must be configured on both PEs, so that CE2 responds as though it is connected to the same system.

• The same ethernet-segment may be used for EVPN-MPLS, EVPN-VXLAN and PBB-EVPN services.

  Note: The source-bmac-lsb attribute must be defined for PBB-EVPN (so that it is only used in PBB-EVPN, and ignored by EVPN). Other than EVPN-MPLS, EVPN-VXLAN and PBB-EVPN I-VPLS/Epipe services, no other Layer 2 services are allowed in the same ethernet-segment (regular VPLS defined on the ethernet-segment is kept operationally down).

• Only one SAP per service can be part of the same ethernet-segment.