The following displays PBB configuration examples:
Ethernet links on BEB1:
BEB1 to BEB1 L1:
BEB1 to BCB1 L1: 1/1/1 – Member port of LAG-emulation ET1, terminate ET3
BEB1 to BCB1 L2: 2/1/1 – Member port of LAG-emulation ET1
BEB1 to BCB1 L3: 3/1/1 – Member port of LAG-emulation ET1
BEB1 to BCB2: 4/1/1 – terminate ET3
*A:7750_ALU>config>eth-tunnel 1
description "LAG-emulation to BCB1 ET1"
protection-type loadsharing
ethernet
mac 00:11:11:11:11:12
encap-type dot1q
exit
ccm-hold-time down 5 up 10 // 50 ms down, 1 sec up
lag-emulation
access adapt-qos distribute
path-threshold 1
exit
path 1
member 1/1/1
control-tag 0
eth-cfm
…
exit
no shutdown
exit
path 2
member 2/1/1
control-tag 0
eth-cfm
…
exit
no shutdown
exit
path 3
member 3/1/1
control-tag 0
eth-cfm
…
exit
no shutdown
exit
no shutdown
--------------------------------------------------
*A:7750_ALU>config>eth-tunnel 3
description "G.8031 tunnel ET3"
protection-type 8031_1to1
ethernet
mac 00:11:11:11:11:11
encap-type dot1q
exit
ccm-hold-time down 5 // 50 ms down, no up hold-down
path 1
member 1/1/1
control-tag 5
precedence primary
eth-cfm
mep 2 domain 1 association 1
ccm-enable
control-mep
no shutdown
exit
exit
no shutdown
exit
path 2
member 4/1/1
control-tag 5
eth-cfm
mep 2 domain 1 association 2
ccm-enable
control-mep
no shutdown
exit
exit
no shutdown
exit
no shutdown
--------------------------------------------------
# Service config
--------------------------------------------------
*A:7750_ALU>config>service vpls 1 customer 1 m-vpls b-vpls create
description "m-VPLS for multipoint traffic"
stp
mst-name "BVPLS"
mode p-mstp
mst-instance 10
mst-priority 4096
vlan-range 100-199
exit
mst-instance 20
mst-priority 8192
vlan-range 200-299
exit
no shutdown
exit
sap eth-tunnel-1 create // BSAP0 to BCB E
sap 4/1/1:0 create // physical link to BCB F (NOTE 0 or 0.*)
// indicate untagged for m-VPLS)
exit
no shutdown
---------------------------------------------------
# Service config: one of the same-fate SAP over
# loadsharing tunnel
---------------------------------------------------
A:7750_ALU>config service vpls 100 customer 1 b-vpls create
sap eth-tunnel-1:1 create //to BCB E
// must specify tags for each path for loadsharing
eth-tunnel
path 1 tag 100
path 2 tag 100
path 3 tag 100
exit
no shutdown …
sap 3/1/1:200 // to BCBF
…
A:7750_ALU>config service vpls 1000 customer 1 i-vpls create
pbb backbone-vpls 100 isid 1000
sap 4/1/1:200 // access SAP to QinQ
…
--------------------------------------------------
# Service config: one of epipes into b-VPLS protected tunnel
# as per R7.0 R4
--------------------------------------------------
A:7750_ALU>config service service vpls 3 customer 1 b-vpls create
sap eth-tunnel-3 create
…
service epipe 2000
pbb-tunnel 100 backbone-dest-mac to-AS20 isid 2000
sap 3/1/1:400 create
Example:
port 1/1/1
— ethernet
— encap-type dot1q
port 2/2/2
— ethernet
— encap-type dot1q
config eth-tunnel 1
— path 1
— member 1/1/1
— control-tag 100
— precedence primary
— eth-cfm
— mep 51 domain 1 association 1 direction down
— ccm-enable
— low-priority-defect allDef
— mac-address 00:AE:AE:AE:AE:AE
— control-mep
— no shutdown
— no shutdown
— path 2
— member 2/2/2
— control-tag 200
— eth-cfm
— mep
— mep 52 domain 1 association 2 direction down
— ccm-enable
— low-priority-defect allDef
— mac-address 00:BE:BE:BE:BE:BE
— control-mep
— no shutdown
— no shutdown
config service vpls 1 b-vpls
— sap eth-tunnel-1
config service epipe 1000
— pbb-tunnel 1 backbone-dest-mac remote-beb
— sap 3/1/1:400.10