sap-ingress [policy-id] [association | match-criteria | detail]
show>qos
Supported on all 7210 SAS platforms as described in this document
This command displays the accounting status of a SAP-ingress policy along with other details of the policy. When frame-based-accounting is enabled, accounting is shown as frame-based, otherwise it is shown as packet-based.
Displays information about the specific policy ID.
Displays the associations of the SAP-ingress policy.
Displays the match criteria of the SAP-ingress policy.
Displays the detailed information of the SAP-ingress policy.
The following output is an example of SAP-ingress QoS policy information, and Table: Output fields: QoS SAP-ingress describes the output fields.
Sample output*A:Dut-1# show qos sap-ingress 1
===============================================================================
QoS Sap Ingress
===============================================================================
-------------------------------------------------------------------------------
Sap Ingress Policy (1)
-------------------------------------------------------------------------------
Policy-id : 1 Scope : Template
Default FC : be
Criteria-type : None
Accounting : frame-based
Classifiers Allowed: 16 Meters Allowed : 8
Classifiers Used : 2 Meters Used : 2
Description : Default SAP ingress QoS policy.
===============================================================================
*A:Dut-1#
|
Label |
Description |
|---|---|
|
Policy-Id |
Displays the ID that uniquely identifies the policy. |
|
Scope |
Exclusive Implies that this policy can only be applied to a single SAP. |
|
Template Implies that this policy can be applied to multiple SAPs on the router. |
|
|
Default FC |
Specifies the default FC for the policy. |
|
Criteria-type |
IP Specifies that an IP criteria-based SAP-ingress policy is used to select the appropriate ingress meter and corresponding FC for matched traffic. |
|
Accounting |
Packet-based Specifies that the meters associated with this policy do not account for packet framing overheads (such as Ethernet the Inter Frame Gap (IFG) and the preamble), while accounting for the bandwidth to be used by this flow. Frame-based Specifies that the meters associated with this policy account for the packet framing overheads (such as for Ethernet the IFG and preamble), while accounting the bandwidth to be used by the flow. |
|
Classifiers Allowed |
Indicates the number of classifiers allowed for a service. |
|
Meters Allowed |
Indicates the number of meters allowed for a service. |
|
Classifiers Used |
Indicates the number of classifiers used for a service. |
|
Meters Used |
Indicates the number of meters used for a service. |
|
Description |
A text string that helps identify the policy’s context in the configuration file. |
network [policy-id] [detail]
show>qos
Supported on all 7210 SAS platforms as described in this document
This command displays the accounting status of a network QoS policy in addition to other details about the policy. When frame-based-accounting is enabled, accounting is shown as frame-based, otherwise it is shown as packet-based.
Displays information about the specific policy ID.
Displays the detailed policy information.
The following output is an example of network information, and Table: Output fields: show QoS network describes the output fields.
Sample output*A:Dut-1# show qos network 1
===============================================================================
QoS Network Policy
===============================================================================
-------------------------------------------------------------------------------
Network Policy (1)
-------------------------------------------------------------------------------
Policy-id : 1 Remark : False
Forward Class : be Profile : Out
Attach Mode : l2 Config Mode : l2+mpls
Scope : Template Policy Type : port
Accounting : frame-based
Description : Default network-port QoS policy.
-------------------------------------------------------------------------------
Meter Mode CIR Admin CIR Rule PIR Admin PIR Rule CBS MBS
-------------------------------------------------------------------------------
1 TrTcm_CA 0 closest max closest 32 128
-------------------------------------------------------------------------------
FC UCastM MCastM
-------------------------------------------------------------------------------
No FC-Map Entries Found.
-------------------------------------------------------------------------------
Port Attachments
-------------------------------------------------------------------------------
Port-id : 1/1/3
Port-id : 1/1/6
Port-id : 1/1/7
Port-id : 1/1/8
Port-id : 1/1/9
===============================================================================
*A:Dut-1#
Label |
Description |
|---|---|
Policy-Id |
The ID that uniquely identifies the policy. |
Remark |
Remarking can be enabled or disabled. |
Forward Class |
Specifies the FC name. |
Profile |
Out Specifies the EXP marking for the packets which are out-of-profile, egressing on this queue. Specifies the dot1p marking for the out-of-profile packets which egressing on this queue. |
In Specifies the EXP marking for the packets which are in-of-profile, egressing on this queue.Specifies the dot1p markings for in-profile packets egressing on this queue. |
|
Scope |
Exclusive Specifies that this policy can be applied only to a single network port. Template Specifies that this policy can be applied to multiple network ports on the router. |
Policy Type |
Specifies the policy type. |
Accounting |
Packet-based Specifies that the meters associated with this policy do not account for packet framing overheads (such as Ethernet the Inter Frame Gap (IFG) and the preamble), while accounting for the bandwidth to be used by this flow. Frame-based Specifies that the meters associated with this policy account for the packet framing overheads (such as for Ethernet the IFG and preamble), while accounting the bandwidth to be used by the flow. |
Description |
A text string that helps identify the policy’s context in the configuration file. |
Meter Mode |
Specifies the configured mode of the meter. |
CIR Admin |
Specifies the administrative Committed Information Rate (CIR) parameters for the meters. |
CIR Rule |
min The operational CIR for the meters will be equal to or greater than the administrative rate specified using the rate command. |
max The operational CIR for the meter will be equal to or less than the administrative rate specified using the rate command. |
|
closest The operational PIR for the meters will be the rate closest to the rate specified using the rate command without exceeding the operational PIR. |
|
PIR Admin |
Specifies the administrative Peak Information Rate (PIR) parameters for the meters. |
PIR Rule |
min The operational CIR for the meters will be equal to or greater than the administrative rate specified using the rate command. |
max The operational CIR for the meter will be equal to or less than the administrative rate specified using the rate command. |
|
closest The operational PIR for the meters will be the rate closest to the rate specified using the rate command without exceeding the operational PIR. |
|
CBS |
def Specifies the default CBS value for the meters. |
value Specifies the value to override the default reserved buffers for the meters. |
|
MBS |
def Specifies the default MBS value. |
value Specifies the value to override the default MBS for the meter. |
|
Port-id |
Specifies the port number. |
access-egress [policy-id] [association | detail]
show>qos
Supported on all 7210 SAS platforms as described in this document
This command displays the accounting status of an access-egress policy in addition to other details about the policy. When frame-based-accounting is enabled, accounting is shown as frame-based, otherwise it is shown as packet-based.
Displays information about the specific policy ID.
Displays the policy associations.
Displays the policy information in detail.
The following output is an example of access-egress QoS policy information, and Table: Output fields: access egress describes the output fields.
Sample output*A:Dut-1# show qos access-egress 1
===============================================================================
QoS Access Egress
===============================================================================
-------------------------------------------------------------------------------
Policy-id : 1 Scope : Template
Remark : False
Accounting : frame-based
Description : Default Access egress QoS policy.
===============================================================================
*A:Dut-1#
Label |
Description |
|---|---|
Policy-Id |
Specifies the ID that uniquely identifies the policy. |
Scope |
Exclusive Specifies that this policy can be applied only to a single access egress port. Template Specifies that this policy can be applied to multiple access ports on the router. |
Remark |
True Specifies that remarking is enabled for all the dot1q-tagged packets that egress the ports on which the sap egress QoS policy is applied and remarking is enabled. False Specifies that remarking is disabled for the policy. |
Accounting |
Packet-based Specifies that the meters associated with this policy do not account for packet framing overheads (such as Ethernet the Inter Frame Gap (IFG) and the preamble), while accounting for the bandwidth to be used by this flow. Frame-based Specifies that the meters associated with this policy account for the packet framing overheads (such as for Ethernet the IFG and preamble), while accounting the bandwidth to be used by the flow. |
Description |
A text string that helps identify the policy’s context in the configuration file |
network-queue [network-queue-policy-name] [detail]
show>qos
Supported on all 7210 SAS platforms as described in this document
This command displays the accounting status of a network-queue policy in addition to other details about the policy. When frame-based-accounting is enabled, accounting is shown as frame-based, otherwise it is shown as packet-based.
Displays information about the specific network queue policy.
Displays the detailed policy information.
The following output is an example of network queue information, and Table: Output fields: network queue describes the output fields.
Sample output*A:Dut-1# show qos network-queue default
===============================================================================
QoS Network Queue Policy
===============================================================================
-------------------------------------------------------------------------------
Network Queue Policy (default)
-------------------------------------------------------------------------------
Policy : default
Accounting : frame-based
Description : Default network queue QoS policy.
-------------------------------------------------------------------------------
Associations
-------------------------------------------------------------------------------
Port-id : 1/1/6
Port-id : 1/1/7
===============================================================================
*A:Dut-1#
Label |
Description |
|---|---|
Policy |
The policy name that uniquely identifies the policy. |
Accounting |
Packet-based Specifies that the meters associated with this policy do not account for packet framing overheads (such as Ethernet the Inter Frame Gap (IFG) and the preamble), while accounting for the bandwidth to be used by this flow. Frame-based Specifies that the meters associated with this policy account for the packet framing overheads (such as for Ethernet the IFG and preamble), while accounting the bandwidth to be used by the flow. |
Description |
A text string that helps identify the policy’s context in the configuration file. |
Port-Id |
Displays the physical port identifier where the network queue policy is applied. |
port-scheduler-policy [port-scheduler-policy-name] [association]
show>qos
Supported on all 7210 SAS platforms as described in this document
This command displays the accounting status of a port-scheduler policy in addition to other details about the policy. When frame-based-accounting is enabled, accounting is shown as frame-based, otherwise it is shown as packet-based.
Displays information about the specific port scheduler policy.
Displays the associations of the port scheduler policy.
The following output is an example of port scheduler policy information, and Table: Output fields: port scheduler policy describes the output fields.
Sample output*A:Dut-1# show qos port-scheduler-policy default
===============================================================================
QoS Port Scheduler Policy
===============================================================================
Policy-Name : default
Description : Default Port Scheduler policy.
Accounting : frame-based
Mode : STRICT
Last changed : 08/06/2001 18:36:04
Number Of Queues : 8
Label |
Description |
|---|---|
Policy-Name |
Displays the port scheduler policy name. |
Mode |
Displays the port scheduler policy mode (STRICT, RR, WRR, WDRR). |
Accounting |
Packet-based Specifies that the meters associated with this policy do not account for packet framing overheads (such as Ethernet the Inter Frame Gap (IFG) and the preamble), while accounting for the bandwidth to be used by this flow. Frame-based Specifies that the meters associated with this policy account for the packet framing overheads (such as for Ethernet the IFG and preamble), while accounting the bandwidth to be used by the flow. |
Last Changed |
Displays the last time the configuration changed. |
Queue # |
Displays the weight of the queue if configured. |