twamp-light
show>router
show>service
7210 SAS-Dxp, 7210 SAS-K 2F1C2T, 7210 SAS-K 2F6C4T, and 7210 SAS-K 3SFP+ 8C
This command displays TWAMP Light information.
The following output is an example of TWAMP light information, and Table: Output fields: TWAMP light describes the output fields.
Sample outputshow router twamp-light
-------------------------------------------------------------------------------
TWAMP-Light Reflector
-------------------------------------------------------------------------------
Admin State : Up UDP Port : 15000
Description : (Not Specified)
Up Time : 0d 00:02:24
Test Frames Received : 0 Test Frames Sent : 0
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
TWAMP-Light Reflector Prefixes
-------------------------------------------------------------------------------
Prefix Description
-------------------------------------------------------------------------------
172.16.1.0/24
-------------------------------------------------------------------------------
No. of TWAMP-Light Reflector Prefixes: 1
-------------------------------------------------------------------------------
show service id 500 twamp-light
-------------------------------------------------------------------------------
TWAMP-Light Reflector
-------------------------------------------------------------------------------
Admin State : Up UDP Port : 15000
Description : TWAMP Light reflector VPRN 500
Up Time : 0d 01:47:12
Test Frames Received : 6431 Test Frames Sent : 6431
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
TWAMP-Light Reflector Prefixes
-------------------------------------------------------------------------------
Prefix Description
-------------------------------------------------------------------------------
10.2.1.1/32 Process only 10.2.1.1 TWAMP Light
Packets
172.16.1.0/24 Process all 172.16.1.0 TWAMP
Light packets
-------------------------------------------------------------------------------
No. of TWAMP-Light Reflector Prefixes: 2
-------------------------------------------------------------------------------
Label |
Description |
|---|---|
TWAMP Light Reflector |
|
Admin State |
Up—Specifies that the server or prefix is administratively enabled (no shutdown) in configuration Down—Specifies that the server or prefix is administratively disabled (shutdown) in configuration |
Description |
Text string to describe the context of the protocol |
Up Time |
The time since the server process was started, measured in days (d), hours, minutes, and seconds |
UDP Port |
The UDP port number used |
Test Frames Received |
The total number of frames received from session senders |
Test Frames Sent |
The total number of frames sent to session senders |
Prefixes |
The time since the server process was started, measured in days (d), hours, minutes, and seconds |
saa [test-name] [owner test-owner]
show>saa
Supported on all 7210 SAS platforms as described in this document
This command displays information about the SAA test.
If no specific test is specified, a summary of all configured tests is displayed.
If a specific test is specified, detailed test results for that test are displayed for the last three occurrences that this test has been executed, or since the last time the counters have been reset via a system reboot or clear command.
Specifies the name of the SAA test for which the information needs to be displayed. The test name must already be configured in the config>saa>test context.
This is an optional parameter.
Specifies the owner of an SAA operation up to 32 characters.
The following output is an example of SAA information, and Table: Output fields: SAA describes the output fields.
Sample output*A:7210 SAS>show# saa
===============================================================================
SAA Test Information
===============================================================================
Test name : abc
Owner name : TiMOS CLI
Description : test
Accounting policy : None
Administrative status : Disabled
Test type : Not configured
Trap generation : None
Test runs since last clear : 0
Number of failed test runs : 0
Last test result : Undetermined
-------------------------------------------------------------------------------
Threshold
Type Direction Threshold Value Last Event Run #
-------------------------------------------------------------------------------
Jitter-in Rising None None Never None
Falling None None Never None
Jitter-out Rising None None Never None
Falling None None Never None
Jitter-rt Rising 100 None Never None
Falling 10.0 None Never None
Latency-in Rising None None Never None
Falling None None Never None
Latency-out Rising None None Never None
Falling None None Never None
Latency-rt Rising 100 None Never None
Falling 20.0 None Never None
Loss-in Rising None None Never None
Falling None None Never None
Loss-out Rising None None Never None
Falling None None Never None
Loss-rt Rising 300 None Never None
Falling 30 None Never None
===============================================================================
===============================================================================
*A:7210 SAS>show#
Label |
Description |
|---|---|
Test Name |
Specifies the name of the test. |
Owner Name |
Specifies the owner of the test. |
Description |
Specifies the description for the test type. |
Accounting policy |
Specifies the associated accounting policy ID. |
Administrative status |
Specifies whether the administrative status is enabled or disabled. |
Test type |
Specifies the type of test configured. |
Trap generation |
Specifies the trap generation for the SAA test. |
Test runs since last clear |
Specifies the total number of tests performed since the last time the tests were cleared. |
Number of failed tests run |
Specifies the total number of tests that failed. |
Last test run |
Specifies the last time a test was run. |
Threshold type |
Indicates the type of threshold event being tested, jitter-event, latency-event, or loss-event, and the direction of the test responses received for a test run: in — inbound out — outbound rt — roundtrip |
Direction |
Indicates the direction of the event threshold, rising or falling. |
Threshold |
Displays the configured threshold value. |
Value |
Displays the measured crossing value that triggered the threshold crossing event. |
Last event |
Indicates the time that the threshold crossing event occurred. |
Run # |
Indicates what test run produced the specified values. |
test-oam
show
7210 SAS-D, 7210 SAS-Dxp, 7210 SAS-K 2F1C2T, 7210 SAS-K 2F6C4T, and 7210 SAS-K 3SFP+ 8C
Commands in this context display Operations, Administration, and Maintenance test parameters.
A maximum of 1000 running instances are stored on the node. When the maximum is reached, the older entries are overwritten.
The following output is an example of OAM test parameters.
Sample output*A:Dut-A# show saa "Dut-A:1413:1501" owner "TiMOS"
===============================================================================
SAA Test Information
===============================================================================
Test name : Dut-A:1413:1501
Owner name : TiMOS
Administrative status : Enabled
Test type : vccv-ping 1413:1501 fc "nc" timeout 10 size 200
count 2
Test runs since last clear : 1
Number of failed test runs : 0
Last test result : Success
-------------------------------------------------------------------------------
Threshold
Type Direction Threshold Value Last Event Run #
-------------------------------------------------------------------------------
Jitter-in Rising None None Never None
Falling None None Never None
Jitter-out Rising None None Never None
Falling None None Never None
Jitter-rt Rising None None Never None
Falling None None Never None
Latency-in Rising None None Never None
Falling None None Never None
Latency-out Rising None None Never None
Falling None None Never None
Latency-rt Rising 100 None Never None
Falling None None Never None
Loss-in Rising None None Never None
Falling None None Never None
Loss-out Rising None None Never None
Falling None None Never None
Loss-rt Rising 2 None Never None
Falling None None Never None
===============================================================================
Test Run: 144
Total number of attempts: 2
Number of requests that failed to be sent out: 0
Number of responses that were received: 2
Number of requests that did not receive any response: 0
Total number of failures: 0, Percentage: 0
(in ms) Min Max Average Jitter
Outbound : 0 0 0 0
Inbound : 10 20 15 0
Roundtrip : 10 20 15 0
Per test packet:
Sequence Outbound Inbound RoundTrip Result
1 0 20 20 EgressRtr(10.20.1.4)
2 0 10 10 EgressRtr(10.20.1.4)
===============================================================================
*A:Dut-A#
acceptance-criteria acceptance-criteria-id] [running-instance running-instance] [detail]
show>test-oam
7210 SAS-D, 7210 SAS-K 2F1C2T, 7210 SAS-K 2F6C4T, and 7210 SAS-K 3SFP+ 8C
This command displays the configuration of the acceptance criteria. Both summary and detailed information is available; detailed information is displayed using the detail keyword. The running-instance parameter specifies information for a particular instance of the service test.
Specifies the acceptance criteria identifier.
Specifies a particular instance of the service test.
The following output is an example of acceptance criteria configuration information.
Sample output*A:Dut-B# show test-oam acceptanc-criteria 2 detail
===============================================================================
Y.1564 Acceptance criteria 2
===============================================================================
Desc : Acceptance_Criteria_2
cir : 199990 pir : 249750
Latency Threshold: 45 Frame Loss Th*: 0
Jitter threshold : 0 M-Factor : 1000
FLR. Thr. In : -1 FLR. Thr. Out : -1
Lat. Thr. In : -1 Lat. Thr. Out : -1
Jit. Thr. In : -1 Jit. Thr. Out : -1
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:Dut-B#
frame-payload frame-payload-id [running-instance running-instance] [detail]
show>test-oam
7210 SAS-K 2F1C2T, 7210 SAS-K 2F6C4T, and 7210 SAS-K 3SFP+ 8C
This command displays the configuration of the packet header values used in frames generated by the service test testhead tool. Both summary and detailed information is available; detailed information is displayed using the detail keyword. The running-instance parameter specifies information for a particular instance of the service test.
Specifies the acceptance test identifier.
Specifies a particular instance of the service test.
The following output is an example of frame payload configuration information, and Table: Output fields: frame payload describes the output fields.
Sample output*A:Dut-B# show test-oam frame-payload 1 detail
===============================================================================
Y.1564 frame payload 1
===============================================================================
Type : l2 Desc : Frame_Payload_1
Ether type : 2048 Ip proto : 0
IP TOS : 0 Ip TTL : 255
DSCP : be Data Pattern :
Dest IP : 0.0.0.0 Dest MAC : 00:00:00:00:00:02
Src IP : 0.0.0.0 Src MAC : 00:00:00:00:00:01
Dest port : 0 Src port : 0
===============================================================================
*A:Dut-B#
Label |
Description |
|---|---|
Desc |
Displays the description configured by the user for the acceptance criteria |
Dest IP |
Displays the destination IP address |
Dest MAC |
Displays the destination MAC address |
Src IP |
Displays the source IP address |
Src MAC |
Displays the source MAC address |
Dest port |
Displays the destination port number |
Src port |
Displays the source port number |
ldp-treetrace [prefix ip-prefix/mask] [detail]
show>test-oam
7210 SAS-K 2F6C4T and 7210 SAS-K 3SFP+ 8C
This command displays OAM LDP treetrace information.
Specifies the address prefix and subnet mask of the destination node.
Specifies to display detailed information.
The following output is an example of OAM LDP treetrace information.
Sample output*A:ALA-48# show test-oam ldp-treetrace
Admin State : Up Discovery State : Done
Discovery-intvl (min) : 60 Probe-intvl (min) : 2
Probe-timeout (min) : 1 Probe-retry : 3
Trace-timeout (sec) : 60 Trace-retry : 3
Max-TTL : 30 Max-path : 128
Forwarding-class (fc) : be Profile : Out
Total Fecs : 400 Discovered Fecs : 400
Last Discovery Start : 12/19/2006 05:10:14
Last Discovery End : 12/19/2006 05:12:02
Last Discovery Duration : 00h01m48s
Policy1 : policy-1
Policy2 : policy-2
*A:ALA-48# show test-oam ldp-treetrace detail
Admin State : Up Discovery State : Done
Discovery-intvl (min) : 60 Probe-intvl (min) : 2
Probe-timeout (min) : 1 Probe-retry : 3
Trace-timeout (sec) : 60 Trace-retry : 3
Max-TTL : 30 Max-path : 128
Forwarding-class (fc) : be Profile : Out
Total Fecs : 400 Discovered Fecs : 400
Last Discovery Start : 12/19/2006 05:10:14
Last Discovery End : 12/19/2006 05:12:02
Last Discovery Duration : 00h01m48s
Policy1 : policy-1
Policy2 : policy-2
===============================================================================
Prefix (FEC) Info
===============================================================================
Prefix Path Last Probe Discov Discov
Num Discovered State State Status
-------------------------------------------------------------------------------
10.11.11.1/32 54 12/19/2006 05:10:15 OK Done OK
10.11.11.2/32 54 12/19/2006 05:10:15 OK Done OK
10.11.11.3/32 54 12/19/2006 05:10:15 OK Done OK
…………
10.14.14.95/32 72 12/19/2006 05:11:13 OK Done OK
10.14.14.96/32 72 12/19/2006 05:11:13 OK Done OK
10.14.14.97/32 72 12/19/2006 05:11:15 OK Done OK
10.14.14.98/32 72 12/19/2006 05:11:15 OK Done OK
10.14.14.99/32 72 12/19/2006 05:11:18 OK Done OK
10.14.14.100/32 72 12/19/2006 05:11:20 OK Done OK
===============================================================================
Legend: uP - unexplored paths, tO - trace request timed out
mH - max hop exceeded, mP - max path exceeded
nR - no internal resource
*A:ALA-48# show test-oam ldp-treetrace prefix 10.12.12.10/32
Discovery State : Done Last Discovered : 12/19/2006 05:11:02
Discovery Status : ' OK '
Discovered Paths : 54 Failed Hops : 0
Probe State : OK Failed Probes : 0
*A:ALA-48# show test-oam ldp-treetrace prefix 10.12.12.10/32 detail
Discovery State : Done Last Discovered : 12/19/2006 05:11:02
Discovery Status : ' OK '
Discovered Paths : 54 Failed Hops : 0
Probe State : OK Failed Probes : 0
===============================================================================
Discovered Paths
===============================================================================
PathDest Egr-NextHop Remote-RtrAddr Discovery-time
DiscoveryTtl ProbeState ProbeTmOutCnt RtnCode
-------------------------------------------------------------------------------
127.1.0.5 10.10.1.2 10.12.12.10 12/19/2006 05:11:01
7 OK 0 EgressRtr
127.1.0.9 10.10.1.2 10.12.12.10 12/19/2006 05:11:01
7 OK 0 EgressRtr
127.1.0.15 10.10.1.2 10.12.12.10 12/19/2006 05:11:01
7 OK 0 EgressRtr
127.1.0.19 10.10.1.2 10.12.12.10 12/19/2006 05:11:01
7 OK 0 EgressRtr
127.1.0.24 10.10.1.2 10.12.12.10 12/19/2006 05:11:01
7 OK 0 EgressRtr
127.1.0.28 10.10.1.2 10.12.12.10 12/19/2006 05:11:01
……………..
127.1.0.252 10.10.1.2 10.12.12.10 12/19/2006 05:11:01
7 OK 0 EgressRtr
127.1.0.255 10.10.1.2 10.12.12.10 12/19/2006 05:11:01
7 OK 0 EgressRtr
===============================================================================
*A:ALA-48#
service-test test-id [service-stream stream-id] [test-type test-type] [running-instance running-instance] [detail]
service-test [test-id] [running-instance running-instance] resource-usage
service-test test-id [service-stream stream-id] [test-type test-type] [running-instance running-instance] results [detail]
service-test [test-id] [service-stream stream-id] [test-type test-type] [running-instance running-instance] results-summary
show>test-oam
7210 SAS-K 2F1C2T, 7210 SAS-K 2F6C4T, and 7210 SAS-K 3SFP+ 8C
This command displays the results of a specified service test. Both summary and detailed information is available; detailed information is displayed using the detail keyword. Further information is available when the optional parameters are specified. The running-instance parameter specifies information for a particular instance of the service test.
Specifies the service test identifier.
Specifies the identifier for a service stream.
Specifies the type of service test.
Specifies a particular instance of the service test.
Specifies to display detailed information.
Displays the memory used by the stored results of a service test if a test-id is specified, or if no test-id is specified, displays the memory used by the stored results of all service tests that are under execution or completed.
Displays the results of the specified service test.
Displays a summary output of service test results that provides basic information about the results of a service test if a test-id is specified, or if no test-id is specified, about the results of all service tests that are under execution or completed. This parameter is also applicable for a specific stream ID of a service test.
The following outputs are examples of service test configuration information.
Sample outputA:Dut-B# show test-oam service-test resource-usage
-------------------------------------------------------------------------------
Y.1564 service test results
-------------------------------------------------------------------------------
Run |Service | | |Mem.Use
Ins. |Test |Start time |End time |(bytes)
-------------------------------------------------------------------------------
2 1 04/12/2018 14:25:40 04/12/2018 14:28:45 1060
3 1 04/12/2018 14:33:56 04/12/2018 14:36:06 1408
4 2 04/12/2018 14:34:00 04/12/2018 14:35:05 1060
*A:Dut-B# show test-oam service-test results-summary
-------------------------------------------------------------------------------
Y.1564 service test results
-------------------------------------------------------------------------------
Run |Svc | | | | | | | |
Instance |Tst |Start time |End time |S|R|B|F|L|J
-------------------------------------------------------------------------------
2 1 04/12/2018 14:25:40 04/12/2018 14:28:45 |N|P|P|P|P|P
3 1 04/12/2018 14:33:56 04/12/2018 14:36:06 |N|P|P|P|P|P
4 2 04/12/2018 14:34:00 04/12/2018 14:35:05 |N|P|P|P|P|P
-------------------------------------------------------------------------------
S - test stopped - Yes/No;
R - Result for all tests - Pass/Fail/NA;
B - Bandwidth/Throughput measured - Pass/Fail/NA;
F - Frame Loss Ratio(FLR) measured - Pass/Fail/NA;
L - Latency measured - Pass/Fail/NA;
J - Jitter measured - Pass/Fail/NA;
-------------------------------------------------------------------------------
A:Dut-B# show test-oam service-test 1 results-summary
-------------------------------------------------------------------------------
Y.1564 service test 1 results
-------------------------------------------------------------------------------
Run Inst. |Svc | | | | | | | | |
/SAP |Str |Test |Start time |End time |S|R|B|F|L|J
-------------------------------------------------------------------------------
2 - - 04/12/2018 14:25:40 04/12/2018 14:28:45 |N|P|P|P|P|P
1/1/2 1 cir 04/12/2018 14:25:40 NA |N|P|P|P|P|P
-------------------------------------------------------------------------------
3 - - 04/12/2018 14:33:56 04/12/2018 14:36:06 |N|P|P|P|P|P
1/1/2 1 cir 04/12/2018 14:33:56 NA |N|P|P|P|P|P
1/1/2 2 cir 04/12/2018 14:35:01 NA |N|P|P|P|P|P
-------------------------------------------------------------------------------
S - test stopped - Yes/No;
R - Result for all tests - Pass/Fail/NA;
B - Bandwidth/Throughput measured - Pass/Fail/NA;
F - Frame Loss Ratio(FLR) measured - Pass/Fail/NA;
L - Latency measured - Pass/Fail/NA;
J - Jitter measured - Pass/Fail/NA;
-------------------------------------------------------------------------------
*A:Dut-B# show test-oam service-test 1
===============================================================================
Y.1564 service test 1
===============================================================================
Service test id : 1 Run instance : 1
Status : finished Stopped : no
Latest running i*: 4
===============================================================================
* indicates that the corresponding row element may have been truncated.
===============================================================================
Y.1564 service test 1 stream 1
===============================================================================
Stream Id : 1 Desc : Stream_1
SAP : 1/1/2 FC : be
Accept. Crit. : 2 Frame Payload : 1
Frame size : 512
Cir : 200000 adaptation : min
Pir : 250000 adaptation : closest
Tests : cir
===============================================================================
===============================================================================
Y.1564 service test 1 stream 2
===============================================================================
Stream Id : 2 Desc : Stream_2
SAP : 1/1/2 FC : be
Accept. Crit. : 2 Frame Payload : 1
Frame size : 512
Cir : 200000 adaptation : min
Pir : 250000 adaptation : closest
Tests : cir
===============================================================================
===============================================================================
Y.1564 service test 1 stream 3
===============================================================================
Stream Id : 3 Desc : Stream_3
SAP : 1/1/2 FC : be
Accept. Crit. : 2 Frame Payload : 1
Frame size : 512
Cir : 200000 adaptation : min
Pir : 250000 adaptation : closest
Tests : cir
===============================================================================
===============================================================================
Y.1564 service test 1 stream 4
===============================================================================
Stream Id : 4 Desc : Stream_4
SAP : 1/1/2 FC : be
Accept. Crit. : 2 Frame Payload : 1
Frame size : 512
Cir : 200000 adaptation : min
Pir : 250000 adaptation : closest
Tests : cir
===============================================================================
*A:Dut-B#
*A:Dut-B# show test-oam service-test 1 service-stream 1 detail
===============================================================================
Y.1564 service test 1
===============================================================================
Service test id : 1 Run instance : 1
Status : finished Stopped : no
Latest running i*: 4
test owner : service-strea*: sequential
shutdown : false trap enabled : false
CIR test time : 60 CIR-PIR test *: 180
Policing test ti*: 600 Performance t*: 900
FLR result : not-applicable Thruput result: not-available
Latency result : not-applicable Jitter result : not-applicable
accounting policy: 0 stats collect*: false
===============================================================================
* indicates that the corresponding row element may have been truncated.
===============================================================================
Y.1564 service test 1 stream 1
===============================================================================
Stream Id : 1 Desc : Stream_1
SAP : 1/1/2 FC : be
Accept. Crit. : 2 Frame Payload : 1
Frame size : 512
Cir : 200000 adaptation : min
Pir : 250000 adaptation : closest
Tests : cir
===============================================================================
===============================================================================
Y.1564 frame payload 1
===============================================================================
Type : l2 Desc : Frame_Payload_1
Ether type : 2048 Ip proto : 0
IP TOS : 0 Ip TTL : 255
DSCP : be Data Pattern :
Dest IP : 0.0.0.0 Dest MAC : 00:00:00:00:00:02
Src IP : 0.0.0.0 Src MAC : 00:00:00:00:00:01
Dest port : 0 Src port : 0
===============================================================================
===============================================================================
Y.1564 Acceptance criteria 2
===============================================================================
Desc : Acceptance_Criteria_2
cir : 199990 pir : 249750
Latency Threshold: 45 Frame Loss Th*: 0
Jitter threshold : 0 M-Factor : 1000
FLR. Thr. In : -1 FLR. Thr. Out : -1
Lat. Thr. In : -1 Lat. Thr. Out : -1
Jit. Thr. In : -1 Jit. Thr. Out : -1
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:Dut-B#
*A:Dut-B# show test-oam service-test 1 running-instance 1 detail
===============================================================================
Y.1564 service test 1
===============================================================================
Service test id : 1 Run instance : 1
Status : finished Stopped : no
Latest running i*: 4
test owner : service-strea*: sequential
shutdown : false trap enabled : false
CIR test time : 60 CIR-PIR test *: 180
Policing test ti*: 600 Performance t*: 900
FLR result : not-applicable Thruput result: not-available
Latency result : not-applicable Jitter result : not-applicable
accounting policy: 0 stats collect*: false
===============================================================================
* indicates that the corresponding row element may have been truncated.
===============================================================================
Y.1564 service test 1 stream 1
===============================================================================
Stream Id : 1 Desc : Stream_1
SAP : 1/1/2 FC : be
Accept. Crit. : 2 Frame Payload : 1
Frame size : 512
Cir : 200000 adaptation : min
Pir : 250000 adaptation : closest
Tests : cir
===============================================================================
===============================================================================
Y.1564 frame payload 1
===============================================================================
Type : l2 Desc : Frame_Payload_1
Ether type : 2048 Ip proto : 0
IP TOS : 0 Ip TTL : 255
DSCP : be Data Pattern :
Dest IP : 0.0.0.0 Dest MAC : 00:00:00:00:00:02
Src IP : 0.0.0.0 Src MAC : 00:00:00:00:00:01
Dest port : 0 Src port : 0
===============================================================================
===============================================================================
Y.1564 Acceptance criteria 2
===============================================================================
Desc : Acceptance_Criteria_2
cir : 199990 pir : 249750
Latency Threshold: 45 Frame Loss Th*: 0
Jitter threshold : 0 M-Factor : 1000
FLR. Thr. In : -1 FLR. Thr. Out : -1
Lat. Thr. In : -1 Lat. Thr. Out : -1
Jit. Thr. In : -1 Jit. Thr. Out : -1
===============================================================================
* indicates that the corresponding row element may have been truncated.
===============================================================================
Y.1564 service test 1 stream 2
===============================================================================
Stream Id : 2 Desc : Stream_2
SAP : 1/1/2 FC : be
Accept. Crit. : 2 Frame Payload : 1
Frame size : 512
Cir : 200000 adaptation : min
Pir : 250000 adaptation : closest
Tests : cir
===============================================================================
===============================================================================
Y.1564 frame payload 1
===============================================================================
Type : l2 Desc : Frame_Payload_1
Ether type : 2048 Ip proto : 0
IP TOS : 0 Ip TTL : 255
DSCP : be Data Pattern :
Dest IP : 0.0.0.0 Dest MAC : 00:00:00:00:00:02
Src IP : 0.0.0.0 Src MAC : 00:00:00:00:00:01
Dest port : 0 Src port : 0
===============================================================================
===============================================================================
Y.1564 Acceptance criteria 2
===============================================================================
Desc : Acceptance_Criteria_2
cir : 199990 pir : 249750
Latency Threshold: 45 Frame Loss Th*: 0
Jitter threshold : 0 M-Factor : 1000
FLR. Thr. In : -1 FLR. Thr. Out : -1
Lat. Thr. In : -1 Lat. Thr. Out : -1
Jit. Thr. In : -1 Jit. Thr. Out : -1
===============================================================================
* indicates that the corresponding row element may have been truncated.
===============================================================================
Y.1564 service test 1 stream 3
===============================================================================
Stream Id : 3 Desc : Stream_3
SAP : 1/1/2 FC : be
Accept. Crit. : 2 Frame Payload : 1
Frame size : 512
Cir : 200000 adaptation : min
Pir : 250000 adaptation : closest
Tests : cir
===============================================================================
===============================================================================
Y.1564 frame payload 1
===============================================================================
Type : l2 Desc : Frame_Payload_1
Ether type : 2048 Ip proto : 0
IP TOS : 0 Ip TTL : 255
DSCP : be Data Pattern :
Dest IP : 0.0.0.0 Dest MAC : 00:00:00:00:00:02
Src IP : 0.0.0.0 Src MAC : 00:00:00:00:00:01
Dest port : 0 Src port : 0
===============================================================================
===============================================================================
Y.1564 Acceptance criteria 2
===============================================================================
Desc : Acceptance_Criteria_2
cir : 199990 pir : 249750
Latency Threshold: 45 Frame Loss Th*: 0
Jitter threshold : 0 M-Factor : 1000
FLR. Thr. In : -1 FLR. Thr. Out : -1
Lat. Thr. In : -1 Lat. Thr. Out : -1
Jit. Thr. In : -1 Jit. Thr. Out : -1
===============================================================================
* indicates that the corresponding row element may have been truncated.
===============================================================================
Y.1564 service test 1 stream 4
===============================================================================
Stream Id : 4 Desc : Stream_4
SAP : 1/1/2 FC : be
Accept. Crit. : 2 Frame Payload : 1
Frame size : 512
Cir : 200000 adaptation : min
Pir : 250000 adaptation : closest
Tests : cir
===============================================================================
===============================================================================
Y.1564 frame payload 1
===============================================================================
Type : l2 Desc : Frame_Payload_1
Ether type : 2048 Ip proto : 0
IP TOS : 0 Ip TTL : 255
DSCP : be Data Pattern :
Dest IP : 0.0.0.0 Dest MAC : 00:00:00:00:00:02
Src IP : 0.0.0.0 Src MAC : 00:00:00:00:00:01
Dest port : 0 Src port : 0
===============================================================================
===============================================================================
Y.1564 Acceptance criteria 2
===============================================================================
Desc : Acceptance_Criteria_2
cir : 199990 pir : 249750
Latency Threshold: 45 Frame Loss Th*: 0
Jitter threshold : 0 M-Factor : 1000
FLR. Thr. In : -1 FLR. Thr. Out : -1
Lat. Thr. In : -1 Lat. Thr. Out : -1
Jit. Thr. In : -1 Jit. Thr. Out : -1
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:Dut-B#
eth-cfm
show
Supported on all 7210 SAS platforms as described in this document
Commands in this context display CFM information.
association [ma-index] [detail]
show>eth-cfm
Supported on all 7210 SAS platforms as described in this document
This command displays eth-cfm association information.
Specifies the MA index.
Displays detailed information for the eth-cfm association.
The following output is an example of CFM association information, and Table: Output fields: ETH-CFM association describes the output fields.
Sample output# show eth-cfm association
===============================================================================
CFM Association Table
===============================================================================
Md-index Ma-index Name CCM-intrvl Hold-time Bridge-id
-------------------------------------------------------------------------------
3 1 03-0000000100 1 n/a 100
10 1 FacilityPrt01 1 n/a none
===============================================================================
ALU-IPD#
show eth-cfm association
===============================================================================
CFM Association Table
===============================================================================
Md-index Ma-index Name Int Hold Bridge-id MEPS TxSid
-------------------------------------------------------------------------------
12 1 epipe01-ovcmeg-circuit0* 10 n/a 1 0 yes
12 4 vpls4-0000001 1 n/a 4 2 yes
12 16 abcdefgh 10 n/a none 0 no
14 1 123456789abce 1 n/a 3 3 no
14 2 epipe00000005 1 n/a 5 3 yes
14 3 ivpls-000006 10 n/a 6 1 no
14 5 service4001 10 n/a 5 0 no
15 3 12345678 10 n/a 3 0 no
===============================================================================
* indicates that the corresponding row element may have been truncated.
Label |
Description |
|---|---|
Md-index |
Displays the MD index |
Ma-index |
Displays the MA index |
Name |
Displays the name of the MA |
CCM-interval |
Displays the CCM interval (in seconds) |
Bridge-id |
Displays the bridge ID for the MA. The bridge ID is the same value as the service ID of the service to which the MEP belongs. |
cfm-stack-table [port [port-id [vlan vlan-id]] [level 0..7] [direction up | down]
show>eth-cfm
Supported on all 7210 SAS platforms as described in this document
This command displays stack-table information. This stack-table is used to display the various management points MEPs and MIPs that are configured on the system. These can be Service based or facility based. The various option allow the operator to be specific. If no parameters are include, the entire stack-table is displayed.
Displays the bridge port or aggregated port on which MEPs or MHFs are configured.
Displays the associated VLAN ID.
Displays the MD level of the maintenance point.
Displays the direction in which the MP faces on the bridge port.
The following output is an example of CFM stack table information, and Table: Output fields: CFM stack table describes the output fields.
Sample output*ALU-IPD# show eth-cfm cfm-stack-table
========================================================================
CFM SAP Stack Table
========================================================================
Sap Level Dir Md-index Ma-index Mep-id Mac-address
------------------------------------------------------------------------
lag-1:1.1 0 Down 2 1 10 00:f3:f0:98:97:1b
lag-1:1.1 6 Down 1 1 1 00:f3:f0:98:97:1b
lag-1:2.2 0 Down 2 2 20 00:f3:f0:98:97:1b
lag-1:2.2 6 Down 1 2 2 00:f3:f0:98:97:1b
========================================================================
*ALU-IPD#
Label |
Description |
|---|---|
Sap |
Displays the SAP identifier |
Level |
Displays the MD level of the domain |
Dir (direction) |
Displays the direction of OAMPDU transmission |
Md-index |
Displays the MD index of the domain |
Ma-index |
Displays the MA index of the domain |
Mep-id |
Displays the MEP identifier |
Mac-address |
Displays the MAC address of the MEP |
domain [md-index] [association ma-index | all-associations] [detail]
show>eth-cfm
Supported on all 7210 SAS platforms as described in this document
This command displays domain information.
Specifies the index of the MD to which the MP is associated, or 0, if none.
Specifies the index to which the MP is associated, or 0, if none.
Specifies all associations to the MD.
Specifies detailed domain information.
The following output is an example of CFM domain information, and Table: Output fields: ETH-CFM domain describes the output fields.
Sample output*ALU-IPD# show eth-cfm domain
==============================================================================
CFM Domain Table
==============================================================================
Md-index Level Name Format
------------------------------------------------------------------------------
1 6 none
2 0 none
==============================================================================
*ALU-IPD#
show eth-cfm domain 14 association 2 detail
===============================================================================
Domain 14
Md-index : 14 Level : 4
MHF Creation : defMHFnone
Name Format : none Next Ma Index : 4
Name : (Not Specified)
Creation Origin : manual
-------------------------------------------------------------------------------
Domain 14 Associations:
Md-index : 14 Ma-index : 2
Name Format : icc-based CCM-interval : 1
Auto Discover : True CCM-hold-time : n/a
Name : epipe00000005
Permission : sendIdChassis
Bridge-id : 5 MHF Creation : defMHFnone
PrimaryVlan : 0 Num Vids : 0
MIP LTR Priority : 7
Total MEP Count : 3
Remote Mep Id : 30 (AutoDiscovered) Remote MAC Addr : default
Remote Mep Id : 32 (AutoDiscovered) Remote MAC Addr : default
===============================================================================
Label |
Description |
|---|---|
Domain |
|
Md-index |
Displays the MD index of the domain |
Level |
Displays the MD level of the domain |
Name |
Displays the name of the MD |
Name Format |
Displays the format for the MD name |
Next Ma Index |
Displays the value of the next MA index |
Domain Associations |
|
Md-index |
Displays the MD index of the domain |
Ma-index |
Displays the MA index of the association |
Name Format |
Displays the format for the MA name |
CCM-interval |
Displays the CCM interval (in seconds) |
Name |
Displays the name of the MA |
Bridge-id |
Displays the bridge ID for the MA. The bridge ID is the same value as the service ID of the service to which the MEP belongs. |
PrimaryVlan |
Displays the VLAN ID configured under the config>eth-cfm>domain>association>bridge-identifier>vlan command |
Num Vids |
Displays the number of VLAN IDs and is always 0 |
Remote Mep Id |
Displays the MEP identifier for the remote MEP |
mep mep-id domain md-index association ma-index [loopback] [linktrace] [eth-bandwidth-notification]
mep mep-id domain md-index association ma-index [remote-mepid mep-id | all-remote-mepids]
mep mep-id domain md-index association ma-index eth-test-results [remote-peer mac-address]
mep mep-id domain md-index association ma-index one-way-delay-test [remote-peer mac-address]
mep mep-id domain md-index association ma-index two-way-delay-test [remote-peer mac-address]
mep mep-id domain md-index association ma-index two-way-slm-test [remote-peer mac-address]
show>eth-cfm
Supported on all 7210 SAS platforms as described in this document
This command displays Maintenance Endpoint (MEP) information.
Specifies the index of the MD with which the MEP is associated, or 0, if none.
Specifies the index of the MA with which the MEP is associated, or 0, if none.
Specifies loopback information for the specified MEP.
Specifies linktrace information for the specified MEP.
Specifies the active ETH-BN notification parameters received from the peer and reported to the rate function on the associated port. This keyword is only supported on the 7210 SAS-K 2F1C2T and 7210 SAS-K 2F6C4T.
Specifies remote MEP ID information for the specified MEP.
Specifies remote peer information for the specified MEP.
Specifies one-way delay test information for the specified MEP.
Specifies two-way delay test information for the specified MEP.
Specifies two-way SLM test information for the specified MEP.
Specifies ETH test result information for the specified MEP.
Specifies all remote MEP ID information for the specified MEP.
Specifies detailed MEP information.
The following outputs are examples of MEP information, and the associated tables describe the output fields:
show eth-cfm mep 28 domain 14 association 2 all-remote-mepids detail
===============================================================================
Eth-CFM Remote-MEP Information
===============================================================================
Remote MEP ID : 30 State : True/Grace
Auto Discovered : False RDI : False
Port Status TLV : Up I/F Status TLV : Up
MAC Address : 00:00:00:00:00:30 CCM Last Change : 02/06/2014 21:37:00
Chass. ID SubType: local
Chassis ID : access-012-west
Man Addr Domain : (Not Specified)
Remote MEP ID : 32 State : True/Grace
Auto Discovered : True RDI : False
Port Status TLV : Up I/F Status TLV : Up
MAC Address : 00:00:00:00:00:32 CCM Last Change : 02/06/2014 21:37:00
Chass. ID SubType: chassisComponent
Chassis ID : (Not Specified)
Man Addr Domain : (Not Specified)
===============================================================================
show eth-cfm mep 28 domain 14 association 2 remote-mepid 30 detail
===============================================================================
Eth-CFM Remote-MEP Information
===============================================================================
Remote MEP ID : 30 State : True/Grace
Auto Discovered : False RDI : False
Port Status TLV : Up I/F Status TLV : Up
MAC Address : 00:00:00:00:00:30 CCM Last Change : 02/06/2014 21:37:00
Chass. ID SubType: local
Chassis ID : access-012-west
Man Addr Domain : (Not Specified)
===============================================================================
show eth-cfm mep 28 domain 14 association 2 remote-mepid 30
=============================================================================
Eth-CFM Remote-Mep Table
=============================================================================
R-mepId AD Rx CC RxRdi Port-Tlv If-Tlv Peer Mac Addr CCM status since
-----------------------------------------------------------------------------
30 F True False Up Up 00:00:00:00:00:30 02/06/2014 21:37:00
=============================================================================
Entries marked with a 'T' under the 'AD' column have been auto-discovered.
Label |
Description |
|---|---|
Remote Mep Id |
Displays the MEP identifier for the remote MEP |
Auto Discovered |
Displays whether the MEP is auto-discovered Auto-discovery for remote MEPs is not supported on the 7210 SAS |
RDI |
True — The RDI flag has been received from the remote MEP False — The RDI flag has not been received from the remote MEP |
Port Status TLV |
Displays the contents of the port status TLV in the CCM (Up, Blocked, or Absent), as defined in the 802.1ag specification. |
I/F Status TLV |
Displays the contents of the interface status TLV in the CCM (Up, Blocked, or Absent), as defined in the 802.1ag specification |
MAC Address |
Displays the MAC address |
CCM Last Change |
Displays the last CMM status change |
Chass. ID Subtype |
Displays the format of the chassis ID returned in the Sender ID TLV of the linktrace reply, if any. This value is meaningless if the chassis ID has a length of 0 |
Chassis ID |
Displays the chassis ID returned in the Sender ID TLC of the linktrace reply, if any |
Man Addr Domain |
Displays the TDomain that identifies the type and format of the related ManAddress, used to access the SNMP agent of the system transmitting the linktrace reply |
A:Dut-A>config>port>ethernet# show eth-cfm mep 1 domain 1 association 1 eth-
bandwidth-notification
===============================================================================
Eth-Cfm MEP Configuration Information
===============================================================================
Md-index : 1 Direction : Down
Ma-index : 1 Admin : Enabled
MepId : 1 CCM-Enable : Enabled
Port : 1/1/5 VLAN : 0
Description : (Not Specified)
FngAlarmTime : 0 FngResetTime : 0
FngState : fngReset ControlMep : False
LowestDefectPri : macRemErrXcon HighestDefect : none
Defect Flags : None
Mac Address : d0:99:d5:80:51:a6
CcmPaddingSize : 0 octets
CcmTx : 169 CcmSequenceErr : 0
CcmIgnoreTLVs : (Not Specified)
Fault Propagation: disabled
MA-CcmInterval : 1 MA-CcmHoldTime : 0ms
MA-Primary-Vid : Disabled
MD-Level : 0
Eth-Ais : Disabled
Eth-Ais Tx defCCM: allDef
Eth-BNM Receive : Enabled Eth-BNM Rx Pacing : 5
Redundancy:
MC-LAG State : n/a
CcmLastFailure Frame:
None
XconCcmFailure Frame:
None
Label |
Description |
|---|---|
Md-index |
Displays the MD index of the domain |
Direction |
Displays the direction of OAM PDU transmission |
Ma-index |
Displays the MA index of the association |
Admin |
Displays the administrative status of the MEP |
MepId |
Displays the MEP ID |
CCM-Enable |
Displays the status of the CCM (enabled or disabled) |
Port |
Displays the port number |
VLAN |
Displays the configured VLAN on the MEP |
Description |
Displays the description |
FngAlarmTime |
Displays the fault alarm time |
FngResetTime |
Displays the fault alarm reset time |
FngState |
Displays the different states of the Fault Notification Generator |
LowestDefectPri |
Displays the lowest priority defect (a configured value) that is allowed to generate a fault alarm |
HighestDefect |
Displays the highest defect that is present (for example, if defRDICCM and defXconCCM are present, the highest defect is defXconCCM) |
Defect Flags |
Displays the number of defect flags |
Mac Address |
Displays the MAC address of the MEP |
CcmTx |
Displays the total number of CCM transmitted |
CcmPaddingSize |
Displays the number of octets used to pad a CCM packet |
CcmSequenceErr |
Displays the total number of out-of-sequence CCMs received |
Fault Propagation |
Displays the fault propagation configuration for the MEP |
MA-CcmInterval |
Displays the CCM transmission interval for all MEPs in the association |
MA-CcmHoldTime |
Displays the CCM hold time for all MEPs in the association |
MD-Level |
Displays the MD level |
Eth-Ais |
Displays the state of the ETH-AIS test (enabled or disabled) |
Eth-BNM Receive |
Displays whether ETH-BN receive is enabled or disabled |
Eth-BNM Rx Pacing |
Displays the ETH-BN receive update pacing interval time |
MC-LAG State |
Displays the MC-LAG state |
CcmLastFailure Frame |
Displays the frame that caused the last CCM failure |
XconCcmFailure Frame |
Displays the frame that caused the XconCCMFailure |
mip
show>eth-cfm
7210 SAS-D, 7210 SAS-Dxp, 7210 SAS-K 2F1C2T, 7210 SAS-K 2F6C4T, and 7210 SAS-K 3SFP+ 8C
This command displays SAPs/bindings provisioned for allowing the default MIP creation.
The following output is an example of CFM MIP information.
Sample output*A:node-1# show eth-cfm mip
==========================================================================
CFM SAP MIP Table
==========================================================================
Sap Mip-Enabled Mip Mac Address
--------------------------------------------------------------------------
1/1/1:1.1 yes Not Configured
==========================================================================
==========================================================================
CFM SDP MIP Table
==========================================================================
Sdp Mip-Enabled Mip Mac Address
--------------------------------------------------------------------------
No Matching Entries
statistics
show>eth-cfm
7210 SAS-Dxp, 7210 SAS-K 2F1C2T, 7210 SAS-K 2F6C4T, and 7210 SAS-K 3SFP+ 8C
This command displays the ETH-CFM statistics counters.
The following output is an example of CFM statistics.
Sample output# show eth-cfm system-config
===============================================================================
CFM System Configuration
===============================================================================
Redundancy
MC-LAG Standby MEP Shutdown: true
MC-LAG Hold-Timer : 1 second(s)
Synthetic Loss Measurement
Inactivity Timer : 100 second(s)
===============================================================================
system-config
show>eth-cfm
Supported on all 7210 SAS platforms as described in this document
This command shows various system level configuration parameters. These global eth-cfm commands are those which are configured directly under the config>eth-cfm context.
The following output is an example of system configuration information.
Sample output# show eth-cfm system-config
===============================================================================
CFM System Configuration
===============================================================================
Redundancy
MC-LAG Standby MEP Shutdown: true
MC-LAG Hold-Timer : 1 second(s)
Synthetic Loss Measurement
Inactivity Timer : 100 second(s)
===============================================================================
*A:cses-V28# show eth-cfm system-config
===============================================================================
CFM System Configuration
===============================================================================
Redundancy
MC-LAG Standby MEP Shutdown: false
MC-LAG Hold-Timer : 1 second(s)
Synthetic Loss Measurement
Inactivity Timer : 100 second(s)
ETH-CCM Grace-Period
Transmit Enabled : true
Sender ID Information
ChassisID Subtype : local
ChassisID : access-012-north
-------------------------------------------------------------------------------
ETH-CFM System Configuration Limits
-------------------------------------------------------------------------------
Component Current Usage System Limit
-------------------------------------------------------------------------------
Maintenance Domain (MD) 3 50
Maintenance Association (MA) 8 25000
Extended MA (up to 400 MEPs) 0 10
Maintenance Endpoint (MEP) 4 25000
One-second MEP 3 5000
Sub-second MEP 0 5000
Alarm Indication Signal (AIS) 0 25000
Client Signal Fail (CSF) 0 25000
Primary Vlan Ingress MP 1 19999
Primary Vlan Egress MP 1 19999
-------------------------------------------------------------------------------
===============================================================================
oam eth-cfm linktrace 00:00:00:00:00:30 mep 28 domain 14 association 2
Index Ingress Mac Egress Mac Relay Action
----- -------------------- -------------------- ---------- ----------
1 00:00:00:00:00:00 00:00:00:00:00:30 n/a terminate
SenderId TLV: ChassisId (local)
access-012-west
----- -------------------- -------------------- ---------- ----------
No more responses received in the last 6 seconds.
twamp
show>test-oam
7210 SAS-D, 7210 SAS-Dxp, 7210 SAS-K 2F1C2T, and 7210 SAS-K 2F6C4T
Commands in this context request TWAMP information.
twamp-light
show>test-oam>twamp
7210 SAS-Dxp, 7210 SAS-K 2F1C2T, and 7210 SAS-K 2F6C4T
Commands in this context request TWAMP Light information.
reflectors
show>test-oam>twamp>twamp-light
7210 SAS-Dxp, 7210 SAS-K 2F1C2T, and 7210 SAS-K 2F6C4T
This command displays TWAMP Light reflector information.
The following output is an example of TWAMP light reflector information, and Table: Output fields: TWAMP Light reflectors describes the output fields.
Sample outputshow test-oam twamp twamp-light reflectors
=======================================================================
TWAMP-Light Reflectors
=======================================================================
Router/VPRN Admin UDP Port Prefixes Frames Rx Frames Tx
-----------------------------------------------------------------------
Base Up 15000 1 0 0
500 Up 15000 2 6340 6340
-----------------------------------------------------------------------
No. of TWAMP-Light Reflectors: 2
=======================================================================
Label |
Description |
|---|---|
TWAMP Light Reflector |
|
Router/VPRN |
The TWAMP Light clients |
Admin |
Displays one of the following: Up—the server or prefix is administratively enabled (no shutdown) in configuration Down—the server or prefix is administratively disabled (shutdown) in configuration |
UDP Port |
The UDP port number used |
Prefixes |
The time since the server process was started, measured in days (d), hours, minutes, and seconds |
Frames Rx |
The total number of frames received from session senders |
Frames Tx |
The total number of frames sent to session senders |
server
server all
server prefix ip-prefix/mask
show>test-oam>twamp
7210 SAS-D, 7210 SAS-Dxp, 7210 SAS-K 2F1C2T, and 7210 SAS-K 2F6C4T
This command displays information about the TWAMP server. It displays summary information for the ip-prefix in use.
Specifies to display all information about the TWAMP server.
Specifies the TWAMP server IPv4 or IPv6 address prefix.
Specifies the mask length.
The following outputs are examples of TWAMP server information, and Table: Output fields: TWAMP server describes the output fields.
Sample output: standard*A:Dut-G>show>test-oam# twamp server
===============================================================================
TWAMP Server
===============================================================================
Admin State : Down Operational State : Down
Up Time : 0d 00:00:00
Current Connections : 0 Max Connections : 8
Connections Rejected : 0 Inactivity Time Out : 900 seconds
Current Sessions : 0 Max Sessions : 8
Sessions Rejected : 0 Sessions Aborted : 0
Sessions Completed : 0
Test Packets Rx : 0 Test Packets Tx : 0
===============================================================================
===============================================================================
TWAMP Server Prefix Summary
===============================================================================
Prefix Current Current Description
Connections Sessions
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
No. of TWAMP Server Prefixes: 0
===============================================================================
*A:Dut-G>show>test-oam#
7210SAS# show test-oam twamp server all
===============================================================================
TWAMP Server
===============================================================================
Admin State : Up Operational State : Up
Up Time : 0d 08:17:34
Current Connections : 0 Max Connections : 16
Connections Rejected : 0 Inactivity Time Out : 900 seconds
Current Sessions : 0 Max Sessions : 16
Sessions Rejected : 0 Sessions Aborted : 0
Sessions Completed : 0
Test Packets Rx : 0 Test Packets Tx : 0
===============================================================================
===============================================================================
TWAMP Server Prefix 10.1.1.0/24
===============================================================================
Description : (Not Specified)
Current Connections : 0 Max Connections : 16
Connections Rejected : 0
Current Sessions : 0 Max Sessions : 16
Sessions Rejected : 0 Sessions Aborted : 0
Sessions Completed : 0
Test Packets Rx : 0 Test Packets Tx : 0
===============================================================================
===============================================================================
Connection information for TWAMP server prefix 10.1.1.0/24
===============================================================================
Client State Curr Sessions Sessions Rejected Sessions Completed
Idle Time (s) Test Packets Rx Test Packets Tx
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
No. of TWAMP Server Connections for Prefix 10.1.1.0/24: 0
===============================================================================
===============================================================================
TWAMP Server Prefix 10.1.1.0/24
===============================================================================
Description : (Not Specified)
Current Connections : 0 Max Connections : 16
Connections Rejected : 0
Current Sessions : 0 Max Sessions : 16
Sessions Rejected : 0 Sessions Aborted : 0
Sessions Completed : 0
Test Packets Rx : 0 Test Packets Tx : 0
===============================================================================
===============================================================================
Connection information for TWAMP server prefix 10.1.1.0/24
===============================================================================
Client State Curr Sessions Sessions Rejected Sessions Completed
Idle Time (s) Test Packets Rx Test Packets Tx
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
No. of TWAMP Server Connections for Prefix 10.1.1.0/24: 0
===============================================================================
===============================================================================
No. of TWAMP Server Prefixes: 2
===============================================================================
*A:7210SAS# show test-oam twamp server prefix 10.1.1.0/24
===============================================================================
TWAMP Server Prefix 10.1.1.0/24
===============================================================================
Description : (Not Specified)
Current Connections : 0 Max Connections : 16
Connections Rejected : 0
Current Sessions : 0 Max Sessions : 16
Sessions Rejected : 0 Sessions Aborted : 0
Sessions Completed : 0
Test Packets Rx : 0 Test Packets Tx : 0
===============================================================================
===============================================================================
Connection information for TWAMP server prefix 10.1.1.0/24
===============================================================================
Client State Curr Sessions Sessions Rejected Sessions Completed
Idle Time (s) Test Packets Rx Test Packets Tx
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
No. of TWAMP Server Connections for Prefix 10.1.1.0/24: 0
===============================================================================
Label |
Description |
|---|---|
Admin State |
Displays one of the following: Up — The server or prefix is administratively enabled (no shutdown) in configuration. Down — The server or prefix is administratively disabled (shutdown) in configuration. |
Operational State |
Displays one of the following: Up — The server or prefix is operationally enabled. Down — The server or prefix is operationally disabled. |
Up Time |
The time since the server process was started, measured in days (d), hours, minutes, and seconds. |
Current Connections |
The total number of currently connected clients. |
Max Connections |
The maximum number of connected clients. |
Connections Rejected |
The number of connection rejections. |
Inactivity Timeout |
The configured inactivity timeout for all TWAMP-control connections (inactivity-timeout). |
Current Sessions |
The number of current sessions. |
Max Sessions |
The maximum number of sessions. |
Sessions Rejected |
The number of rejected sessions for the TWAMP client. |
Sessions Aborted |
The number of manually aborted sessions for the TWAMP client. |
Sessions Completed |
The number of completed sessions for the TWAMP client. |
Test Packets Rx |
The number of test packets received. |
Test Packets Tx |
The number of test packets transmitted. |
Description |
The configured description of the TWAMP server. |
Connection information for TWAMP server prefix |
The IP address prefix of a TWAMP server. |
Client |
The IP address of the TWAMP client. |
State |
The operational state of the TWAMP client. |
Curr Sessions |
The number of current sessions for the TWAMP client. |
Idle Time (s) |
The total idle time, in seconds, of the TWAMP client. |
No. of Conns for Prefix |
The total number of connections for the TWAMP server with the displayed IP address prefix. |
No. of TWAMP Server Prefixes |
The total number of displayed TWAMP server IP address prefixes. |
testhead-profile profile-id
show>test-oam
7210 SAS-D, 7210 SAS-Dxp, 7210 SAS-K 2F1C2T, and 7210 SAS-K 2F6C4T
This command specifies the testhead profile ID to use with this run/session of testhead invocation. Testhead profile must be configure beforehand using the commands under config>test-oam>testhead-profile>.
The following output is an example of testhead-profile information, and Table: Output fields: testhead profile describes the output fields.
Sample output*A:7210SAS>config>test-oam># show test-oam testhead-profile 1
===============================================================================
Y.1564 Testhead Profile
===============================================================================
Description : Testhead_Profile_1
Profile Id : 1 Frame Size : 512
CIR Configured : 100 CIR Operational : 96
PIR Configured : 200 PIR Operational : 200
CIR Rule : max Ref. Count : 0
InPrf Dot1p : 2 OutPrf Dot1p : 4
Duration Hrs : 0
Duration Mins : 3
Duration Secs : 0
-------------------------------------------------------------------------------
Acceptance Criteria Id 1
-------------------------------------------------------------------------------
Loss TH : 0.000100 Jitter TH : 100
InProf Loss TH : 0.000100 InProf Jitter TH : 100
OutProf Loss TH : 0.000100 OutProf Jitter TH : 100
Latency TH : 100 Ref. Count : 0
InProf Latency TH : 100 CIR TH : 1000
OutProf Latency TH : 100 PIR TH : 200
-------------------------------------------------------------------------------
Frame Payload Id 1
-------------------------------------------------------------------------------
Payload Type : tcp-ipv4
Description : Frame_Payload_1
Dst Mac : 00:00:00:00:00:02
Src Mac : 00:00:00:00:00:01
Vlan Tag 1 : Not configured
Vlan Tag 2 : Not configured
Ethertype : 0x0800 DSCP : af11
TOS : 8 TTL : 64
Src. IP : 10.1.1.1 Dst. IP : 20.2.2.2
L4 Dst Port : 50 L4 Src Port : 40
Protocol : 6 Ref. Count : 0
Data Pattern : a1b2c3d4e5f6
===============================================================================
*A:7210SAS>config>test-oam>#
Label |
Description |
|---|---|
Description |
Displays the description configured by the user for the test |
Profile Id |
Displays the profile identifier |
CIR Configured |
Displays the value of the CIR configured |
PIR Configured |
Displays the value of the PIR configured |
Frame Size |
Displays the size of the frame |
CIR Operational |
Displays the value of the CIR operational rate configured |
PIR Operational |
Displays the value of the PIR operational rate configured |
CIR Rule |
Displays the adaptation rule configured by the user |
InPrf Dot1p |
Displays the dot1p value used to identify green or in-profile packets |
Ref. Count |
Displays the total number of testhead (completed or running) sessions pointing to a profile or acceptance criteria or a frame payload |
OutPrf Dot1p |
Displays the dot1p value used to identify green or out-of-profile packets |
Duration Hrs, mins, and secs |
Displays the test duration in hours, minutes, and seconds |
Loss TH |
Displays the user configured loss threshold value for comparison with measured value |
Jitter TH |
Displays the user configured jitter threshold value for comparison with measured value |
InProf Loss TH |
Displays the user configured in-profile loss threshold value for comparison with measured value |
OutProf Loss TH |
Displays the user configured out-of-profile loss threshold value for comparison with measured value |
Latency TH |
Displays the user configured latency threshold value for comparison with measured value |
InProf Latency TH |
Displays the user configured in-profile latency threshold value for comparison with measured value |
OutProf Latency TH |
Displays the user configured out-of-profile latency threshold value for comparison with measured value |
InProf Jitter TH |
Displays the user configured in-profile jitter threshold value for comparison with measured value |
OutProf Jitter TH |
Displays the user configured out-of-profile jitter threshold value for comparison with measured value |
CIR TH |
Displays the user configured CIR threshold value for comparison with measured value |
PIR TH |
Displays the user configured PIR threshold value for comparison with measured value |
Payload Type |
Identifies the type of the payload |
Dst Mac |
Displays the value of destination MAC configured by the user to use in the frame generated by the testhead tool |
Src Mac |
Displays the value of source MAC configured by the user to use in the frame generated by the testhead tool |
Vlan Tag 1 |
Displays the values of the outermost vlan-tag configured by the user to use in the frame generated by the testhead tool |
Vlan Tag 2 |
Displays the values of the second vlan-tag configured by the user to use in the frame generated by the testhead tool |
Ethertype |
Displays the values of the ethertype configured by the user to use in the frame generated by the testhead tool |
TOS |
Displays the values of the IP TOS (Type of Service) configured by the user to use in the frame generated by the testhead tool |
Src. IP |
Displays the values of the source IPv4 address configured by the user to use in the frame generated by the testhead tool |
L4 Dst Port |
Displays the values of the TCP header configured by the user to use in the frame generated by the testhead tool |
Protocol |
Displays the values of the IP protocol value configured by the user to use in the frame generated by the testhead tool |
Data Pattern |
Displays the values of the data pattern configured by the user to use in the frame generated by the testhead tool |
DSCP |
Displays the values of the DSCP configured by the user to use in the frame generated by the testhead tool |
TTL |
Displays the values of the IP TTL (Time-to-Live) value configured by the user to use in the frame generated by the testhead tool |
Dst. IP |
Displays the values of the destination IPv4 address configured by the user to use in the frame generated by the testhead tool |
L4 Src Port |
Displays the values of the source port configured by the user to use in the frame generated by the testhead tool |
testhead test-name owner test-owner
show
7210 SAS-D, 7210 SAS-Dxp, 7210 SAS-K 2F1C2T, and 7210 SAS-K 2F6C4T
This command displays the results of the testhead test identified by test-name and owner.
Specifies the name of the testhead. The test name must already be configured in the oam context.
Specifies the owner of an testhead operation up to 32 characters.
The following output is an example of testhead information, and Table: Output fields: testhead describes the output fields.
Sample output*A:7210SAS# show testhead test-me owner owner-me
===============================================================================
Y.1564 Testhead Session
===============================================================================
Owner : owner-me
Test : test-me
Profile Id : 1 SAP : 1/1/2:100
Accept. Crit. Id : 0 Completed : Yes
Frame Payload Id : 1 Stopped : No
Frame Payload Type : tcp-ipv4 FC : be
Color Aware Test : Yes
Start Time : 08/08/2001 19:37:11
End Time : 08/08/2001 19:40:16
Total time taken : 0d 00:03:05
-------------------------------------------------------------------------------
Latency Results
-------------------------------------------------------------------------------
(total pkts in us): Min Max Average Jitter
Roundtrip : 0 0 0 0
(OutPrf pkts in us): Min Max Average Jitter
Roundtrip : 0 0 0 0
(InPrf pkts in us): Min Max Average Jitter
Roundtrip : 0 0 0 0
-------------------------------------------------------------------------------
Packet Count
-------------------------------------------------------------------------------
Total Injected : 42273637
Total Received : 0
OutPrf Injected : 16898179
OutPrf Received : 0
InPrf Injected : 25375450
InPrf Received : 0
-------------------------------------------------------------------------------
Test Compliance Report
-------------------------------------------------------------------------------
Throughput Configd : 962388
Throughput Oper : 962384
Throughput Measurd : 0
PIR Tput Threshld : Not configured
PIR Tput Meas : 0
CIR Tput Threshld : Not configured
CIR Tput Meas : 0
FLR Configured : None
FLR Measurd : Not Applicable
FLR Acceptance : Fail
OutPrf FLR Conf : None
OutPrf FLR Meas : Not Applicable
OutPrf FLR Acep : Not Applicable
InPrf FLR Conf : None
InPrf FLR Meas : Not Applicable
InPrf FLR Acep : Not Applicable
Latency Configd(us): None
Latency Measurd(us): None
Latency Acceptance : Not Applicable
OutPrf Lat Conf(us): None
OutPrf Lat Meas(us): None
OutPrf Lat Acep : Not Applicable
InPrf Lat Conf(us) : None
InPrf Lat Meas(us) : None
InPrf Lat Acep : Not Applicable
Jitter Configd(us) : None
Jitter Measurd(us) : None
Jitter Acceptance : Not Applicable
OutPrf Jit Conf(us): None
OutPrf Jit Meas(us): None
OutPrf Jit Acep : Not Applicable
InPrf Jit Conf(us) : None
InPrf Jit Meas(us) : None
InPrf Jit Acep : Not Applicable
Total Pkts. Tx. : 13 Latency Pkts. Tx. : 8
OutPrf Latency Pkt*: 0 InPrf Latency Pkt*: 0
Total Tx. Fail : 0
===============================================================================
*A:7210SAS# show testhead test-me owner owner-me
Label |
Description |
|---|---|
Owner |
Displays the owner of the test |
Name |
Displays the name of the test |
Description |
Displays the description for the test type |
Profile Id |
Displays the associated profile ID |
Accept. Crit. Id |
Displays the test acceptance criteria ID to be used by the testhead OAM tool to declare the PASS/FAIL result at the completion of the test |
Frame Payload Id |
Displays frame payload ID, that determines the frame content of the frames generated by the tool |
Frame Payload Type |
Displays the type of frame payload to be used in frames generated by testhead tool |
Color Aware Test |
Displays if color aware tests need to be executed |
SAP |
Displays the SAP ID configured |
Completed |
Displays if the test has been completed |
Stopped |
Displays if the test has been stopped |
FC |
Displays the forwarding class (FC) to use to send the frames generated by the testhead tool |
Start Time |
Displays the start time of the test |
End Time |
Displays the end time of the test |
Total time taken |
Displays the total time taken to execute the test |
total pkts in us |
Displays the total packets in microseconds |
OutPrf pkts in us |
Displays the out-of-profile packets in microseconds |
InPrf pkts in us |
Displays the in-profile packets in microseconds |
Total Injected |
Displays the running count of total injected packets, including marker packets |
Total Received |
Displays the running count of total received packets, including marker packets |
OutPrf Injected |
Displays the running count of total out-of-profile packets, excluding marker packets |
OutPrf Received |
Displays the running count of total out-of-profile packets received, including marker packets |
InPrf Injected |
Displays the running count of total in-profile packets, excluding marker packets |
InPrf Received |
Displays the running count of total in-profile packets received, including marker packets |
Throughput Configd |
Displays the CIR Throughput rate Threshold Configured (in Kbps) |
Throughput Oper |
Displays the operational rate used for the configured rate Operational rate is arrived considering the adaptation rule configured by the user and supported hardware rate. |
Throughput Measurd |
Displays the CIR Throughput Measured Value (in Kbps) |
PIR Tput Threshld |
Displays the PIR Throughput rate Threshold Configured (in Kbps) |
PIR Tput Meas |
Displays the PIR Throughput rate Measured Value (in Kbps) |
FLR Configured |
Displays the Frame Loss Ratio Threshold Configured (in-profile) |
FLR Measurd |
Displays the Frame Loss Ratio Measured (in-profile) |
FLR Acceptance |
Displays Pass, Fail, or Not Applicable ‟Pass” if the measured value is less than or equal to the configured threshold and displays "Fail" otherwise, and displays "Not Applicable", if the FLR criteria is not used to determine whether the test is in Passed or Failed status. |
OutPrf FLR Conf |
Displays the out-of-profile Frame Loss Ratio configured |
OutPrf FLR Meas |
Displays the out-of-profile Frame Loss Ratio measured |
OutPrf FLR Acep |
Displays Pass, Fail, or Not Applicable. ‟Pass” if the measured value is less than or equal to the configured threshold and displays ‟Fail” otherwise, and displays ‟Not Applicable”, if the out-of-profile FLR criteria is not used to determine whether the test is in Passed or Failed status. |
InPrf FLR Conf |
Displays the in-profile Frame Loss Ratio configured |
InPrf FLR Meas |
Displays the in-profile Frame Loss Ratio measured |
InPrf FLR Acep |
Displays Pass, Fail, or Not Applicable. ‟Pass” if the measured value is less than or equal to the configured threshold and displays ‟Fail” otherwise, and displays ‟Not Applicable”, if the in-profile FLR criteria is not used to determine whether the test is in Passed or Failed status. |
Latency Configd(us) |
Displays the Latency Threshold configured (in microseconds) |
Latency Measurd(us) |
Displays the Average Latency measured (in microseconds) |
Latency Acceptance |
Displays Pass, Fail, or Not Applicable ‟Pass” if the measured value is less than or equal to the configured threshold and displays ‟Fail” otherwise, and displays ‟Not Applicable”, if the latency criteria is not used to determine whether the test is in Passed or Failed status. |
OutPrf Lat Conf(us) |
Displays the out-of-profile latency configured |
OutPrf Lat Meas(us) |
Displays the out-of-profile latency measured |
OutPrf Lat Acep |
Displays Pass, Fail, or Not Applicable ‟Pass” if the measured value is less than or equal to the configured threshold and displays ‟Fail” otherwise, and displays ‟Not Applicable”, if the out-of-profile latency criteria is not used to determine whether the test is in Passed or Failed status. |
InPrf Lat Conf(us) |
Displays the in-profile latency configured |
InPrf Lat Meas(us) |
Displays the in-profile latency measured |
InPrf Lat Acep |
Displays Pass, Fail, or Not Applicable ‟Pass” if the measured value is less than or equal to the configured threshold and displays "Fail" otherwise, and displays "Not Applicable", if the in-profile latency criteria is not used to determine whether the test is in Passed or Failed status. |
Jitter Configd(us) |
Displays the Jitter Threshold Configured (in microseconds) |
Jitter Measurd(us) |
Displays the Jitter Measured (in microseconds) |
Jitter Acceptance |
Displays Pass, Fail, or Not Applicable ‟Pass” if the measured value is less than or equal to the configured threshold and displays "Fail" otherwise, and displays "Not Applicable", if the jitter criteria is not used to determine whether the test is in Passed or Failed status. |
OutPrf Jit Conf(us) |
Displays the out-of-profile Jitter configured |
OutPrf Jit Meas(us) |
Displays the out-of-profile Jitter measured |
OutPrf Jit Acep |
Displays Pass, Fail, or Not Applicable ‟Pass” if the measured value is less than or equal to the configured threshold and displays "Fail" otherwise, and displays "Not Applicable", if the out-of-profile jitter criteria is not used to determine whether the test is in Passed or Failed status. |
InPrf Jit Conf(us) |
Displays the in-profile Jitter configured |
InPrf Jit Meas(us) |
Displays the in-profile Jitter measured |
InPrf Jit Acep |
Displays Pass, Fail, or Not Applicable. ‟Pass” if the measured value is less than or equal to the configured threshold and displays "Fail" otherwise, and displays "Not Applicable", if the in-profile jitter criteria is not used to determine whether the test is in Passed or Failed status. |
Total Pkts. Tx. |
Total number of packets (that is, data and marker) transmitted by the testhead session for the duration of the test |
OutPrf Latency Pkt* |
Total number of out-of-profile marker packets received by the testhead session for the duration of the test |
Total Tx. Fail |
Total number of failed transmission attempts by the testhead session for the duration of the test |
Latency Pkts. Tx |
Total number of marker packets transmitted by the testhead session for the duration of the test |
InPrf Latency Pkt* |
Total number of in-profile marker packets received by the testhead session for the duration of the test |
bin-group [bin-group-number]
show>oam-pm
7210 SAS-Dxp, 7210 SAS-K 2F1C2T, 7210 SAS-K 2F6C4T, and 7210 SAS-K 3SFP+ 8C
This command displays data for one or all OAM-PM bin groups.
Specifies an OAM-PM bin group.
The following output is an example of OAM-PM bin group information.
Sample outputshow oam-pm bin-group
-------------------------------------------------------------------------------
Configured Lower Bounds for Delay Measurement (DMM) Tests, in microseconds
-------------------------------------------------------------------------------
Group Description Admin Bin FD(us) FDR(us) IFDV(us)
-------------------------------------------------------------------------------
1 OAM PM default bin group (not* Up 0 0 0 0
1 5000 5000 5000
2 10000 - -
-------------------------------------------------------------------------------
2 Up 0 0 0 0
1 1000 5000 100
2 2000 - 200
3 3000 - 300
4 4000 - 400
5 5000 - 500
6 6000 - 600
7 7000 - 700
8 8000 - 800
9 10000 - 1000
-------------------------------------------------------------------------------
3 Down 0 0 0 0
1 6000 5000 8000
2 10000 10000 10000
3 15000 15000 -
4 22000 - -
-------------------------------------------------------------------------------
10 base Up 0 0 0 0
1 5000 5000 5000
2 10000 10000 10000
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
* indicates that the corresponding row element may have been truncated.
show oam-pm bin-group 2
-------------------------------------------------------------------------------
Configured Lower Bounds for Delay Measurement (DMM) Tests, in microseconds
-------------------------------------------------------------------------------
Group Description Admin Bin FD(us) FDR(us) IFDV(us)
-------------------------------------------------------------------------------
2 Up 0 0 0 0
1 1000 5000 100
2 2000 - 200
3 3000 - 300
4 4000 - 400
5 5000 - 500
6 6000 - 600
7 7000 - 700
8 8000 - 800
9 10000 - 1000
-------------------------------------------------------------------------------
bin-group-using [bin-group bin-group-number]
show>oam-pm
7210 SAS-Dxp, 7210 SAS-K 2F1C2T, 7210 SAS-K 2F6C4T, and 7210 SAS-K 3SFP+ 8C
This command displays the list of sessions configured against one or all OAM-PM bin groups.
Specifies an OAM-PM bin group.
The following output is an example of OAM-PM bin group session information.
Sample outputshow oam-pm bin-group-using
=========================================================================
OAM Performance Monitoring Bin Group Configuration for Sessions
=========================================================================
Bin Group Admin Session Session State
-------------------------------------------------------------------------
2 Up eth-vpls-00005 Inact
eth-pm-service-4 Act
-------------------------------------------------------------------------
3 Down eth-epipe-000001 Inact
-------------------------------------------------------------------------
10 Up eth-epipe-00002 Inact
-------------------------------------------------------------------------
=========================================================================
Admin: State of the bin group
Session State: The state of session referencing the bin-group
show oam-pm bin-group-using bin-group 2
=========================================================================
OAM Performance Monitoring Bin Group Configuration for Sessions
=========================================================================
Bin Group Admin Session Session State
-------------------------------------------------------------------------
2 Up eth-vpls-00005 Inact
eth-pm-service-4 Act
-------------------------------------------------------------------------
=========================================================================
Admin: State of the bin group
Session State: The state of session referencing the bin-group
session session-name [{all | base | bin-group | event-mon | meas-interval}]
show>oam-pm
7210 SAS-Dxp, 7210 SAS-K 2F1C2T, 7210 SAS-K 2F6C4T, and 7210 SAS-K 3SFP+ 8C
This command displays the configuration and status information for an OAM-PM session.
Specifies the name of the session. 32 characters maximum.
Specifies all attributes.
Specifies the base configuration option for the session.
Specifies the associated bin group and its attributes.
Specifies configured event monitoring and last TCA information.
Specifies the associated measured interval and its attributes.
The following output is an example of status information for an OAM-PM session.
Sample outputshow oam-pm session "eth-pm-service-4" all
-------------------------------------------------------------------------------
Basic Session Configuration
-------------------------------------------------------------------------------
Session Name : eth-pm-service-4
Description : (Not Specified)
Test Family : ethernet Session Type : proactive
Bin Group : 2
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Ethernet Configuration
-------------------------------------------------------------------------------
Source MEP : 28 Priority : 0
Source Domain : 12 Dest MAC Address : 00:00:00:00:00:30
Source Assoc'n : 4
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
DMM Test Configuration and Status
-------------------------------------------------------------------------------
Test ID : 10004 Admin State : Up
Oper State : Up Data TLV Size : 1000 octets
On-Demand Duration: Not Applicable On-Demand Remaining: Not Applicable
Interval : 1000 ms
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
SLM Test Configuration and Status
-------------------------------------------------------------------------------
Test ID : 10004 Admin State : Up
Oper State : Up Data TLV Size : 1000 octets
On-Demand Duration: Not Applicable On-Demand Remaining: Not Applicable
Interval : 100 ms
CHLI Threshold : 4 HLIs Frames Per Delta-T : 10 SLM frames
Consec Delta-Ts : 10 FLR Threshold : 50%
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
15-mins Measurement Interval Configuration
-------------------------------------------------------------------------------
Duration : 15-mins Intervals Stored : 32
Boundary Type : clock-aligned Clock Offset : 0 seconds
Accounting Policy : none
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Configured Lower Bounds for Delay Measurement (DMM) Tests, in microseconds
-------------------------------------------------------------------------------
Group Description Admin Bin FD(us) FDR(us) IFDV(us)
-------------------------------------------------------------------------------
2 Up 0 0 0 0
1 1000 5000 100
2 2000 - 200
3 3000 - 300
4 4000 - 400
5 5000 - 500
6 6000 - 600
7 7000 - 700
8 8000 - 800
9 10000 - 1000
-------------------------------------------------------------------------------
?
show oam-pm session "eth-pm-service-4" base
-------------------------------------------------------------------------------
Basic Session Configuration
-------------------------------------------------------------------------------
Session Name : eth-pm-service-4
Description : (Not Specified)
Test Family : ethernet Session Type : proactive
Bin Group : 2
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Ethernet Configuration
-------------------------------------------------------------------------------
Source MEP : 28 Priority : 0
Source Domain : 12 Dest MAC Address : 00:00:00:00:00:30
Source Assoc'n : 4
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
DMM Test Configuration and Status
-------------------------------------------------------------------------------
Test ID : 10004 Admin State : Up
Oper State : Up Data TLV Size : 1000 octets
On-Demand Duration: Not Applicable On-Demand Remaining: Not Applicable
Interval : 1000 ms
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
SLM Test Configuration and Status
-------------------------------------------------------------------------------
Test ID : 10004 Admin State : Up
Oper State : Up Data TLV Size : 1000 octets
On-Demand Duration: Not Applicable On-Demand Remaining: Not Applicable
Interval : 100 ms
CHLI Threshold : 4 HLIs Frames Per Delta-T : 10 SLM frames
Consec Delta-Ts : 10 FLR Threshold : 50%
-------------------------------------------------------------------------------
show oam-pm session "eth-pm-service-4" bin-group
-------------------------------------------------------------------------------
Configured Lower Bounds for Delay Measurement (DMM) Tests, in microseconds
-------------------------------------------------------------------------------
Group Description Admin Bin FD(us) FDR(us) IFDV(us)
-------------------------------------------------------------------------------
2 Up 0 0 0 0
1 1000 5000 100
2 2000 - 200
3 3000 - 300
4 4000 - 400
5 5000 - 500
6 6000 - 600
7 7000 - 700
8 8000 - 800
9 10000 - 1000
-------------------------------------------------------------------------------
show oam-pm session "eth-pm-service-4" meas-interval
-------------------------------------------------------------------------------
15-mins Measurement Interval Configuration
-------------------------------------------------------------------------------
Duration : 15-mins Intervals Stored : 32
Boundary Type : clock-aligned Clock Offset : 0 seconds
Accounting Policy : none
-------------------------------------------------------------------------------
sessions [test-family {ethernet | ip}] [event-mon]
show>oam-pm
7210 SAS-Dxp, 7210 SAS-K 2F1C2T, 7210 SAS-K 2F6C4T, and 7210 SAS-K 3SFP+ 8C
This command displays a summary of the OAM-PM sessions.
Specifies Ethernet sessions only.
Specifies IP sessions only.
Specifies a summary of all event monitoring information, and the current state for each session.
The following output is an example of summary information for OAM-PM sessions.
Sample outputshow oam-pm sessions
============================================================================
OAM Performance Monitoring Session Summary for the Ethernet Test Family
============================================================================
Session State Bin Group Sess Type Test Types
----------------------------------------------------------------------------
eth-vpls-00005 Inact 2 proactive DMM SLM
eth-epipe-00002 Inact 10 proactive DMM SLM
eth-epipe-000001 Inact 3 proactive DMM
eth-pm-service-4 Act 2 proactive DMM SLM
============================================================================
show oam-pm sessions test-family ethernet
============================================================================
OAM Performance Monitoring Session Summary for the Ethernet Test Family
============================================================================
Session State Bin Group Sess Type Test Types
----------------------------------------------------------------------------
eth-vpls-00005 Inact 2 proactive DMM SLM
eth-epipe-00002 Inact 10 proactive DMM SLM
eth-epipe-000001 Inact 3 proactive DMM
eth-pm-service-4 Act 2 proactive DMM SLM
============================================================================
statistics
show>oam-pm
7210 SAS-Dxp, 7210 SAS-K 2F1C2T, 7210 SAS-K 2F6C4T, and 7210 SAS-K 3SFP+ 8C
This command displays OAM-PM delay or synthetic loss statistics.
session session-name
show>oam-pm>statistics
7210 SAS-Dxp, 7210 SAS-K 2F1C2T, 7210 SAS-K 2F6C4T, and 7210 SAS-K 3SFP+ 8C
This command displays OAM-PM session statistics.
Specifies the session name. 32 characters maximum.
dmm
show>oam-pm>statistics>session
7210 SAS-Dxp, 7210 SAS-K 2F1C2T, 7210 SAS-K 2F6C4T, and 7210 SAS-K 3SFP+ 8C
This command displays DMM test statistics.
meas-interval raw [{all | bins | summary}]
meas-interval {5-mins | 15-mins | 1-hour | 1-day} interval-number interval-number [{all | bins | summary}]
show>oam-pm>statistics>session>dmm
7210 SAS-Dxp, 7210 SAS-K 2F1C2T, 7210 SAS-K 2F6C4T, and 7210 SAS-K 3SFP+ 8C
This command displays measured interval statistics for DMM tests in the specified session.
Specifies raw information.
Specifies information for 5-minute intervals.
Specifies information for 15-minute intervals.
Specifies information for 1-hour intervals.
Specifies information for 1-day intervals.
Specifies the interval number.
Specifies all information for the interval.
Specifies bin information for the interval.
Specifies summarized information for the interval.
The following output is an example of DMM measured interval statistics information.
Sample outputshow oam-pm statistics session "eth-pm-service-4" dmm meas-interval 15-
mins all interval-number 2
------------------------------------------------------------------------------
Start (UTC) : 2014/02/01 10:15:00 Status : completed
Elapsed (seconds) : 900 Suspect : no
Frames Sent : 900 Frames Received : 900
------------------------------------------------------------------------------
----------------------------------------------------------------------
Bin Type Direction Minimum (us) Maximum (us) Average (us)
----------------------------------------------------------------------
FD Forward 0 11670 779
FD Backward 0 7076 1746
FD Round Trip 1109 13222 2293
FDR Forward 0 11670 779
FDR Backward 0 7076 1738
FDR Round Trip 0 12104 1178
IFDV Forward 0 10027 489
IFDV Backward 0 5444 742
IFDV Round Trip 0 11853 1088
----------------------------------------------------------------------
---------------------------------------------------------------
Frame Delay (FD) Bin Counts
---------------------------------------------------------------
Bin Lower Bound Forward Backward Round Trip
---------------------------------------------------------------
0 0 us 625 244 0
1 1000 us 194 356 465
2 2000 us 50 153 244
3 3000 us 11 121 119
4 4000 us 10 17 40
5 5000 us 5 6 20
6 6000 us 4 2 5
7 7000 us 0 1 3
8 8000 us 0 0 3
9 10000 us 1 0 1
---------------------------------------------------------------
---------------------------------------------------------------
Frame Delay Range (FDR) Bin Counts
---------------------------------------------------------------
Bin Lower Bound Forward Backward Round Trip
---------------------------------------------------------------
0 0 us 890 891 889
1 5000 us 10 9 11
---------------------------------------------------------------
---------------------------------------------------------------
Inter-Frame Delay Variation (IFDV) Bin Counts
---------------------------------------------------------------
Bin Lower Bound Forward Backward Round Trip
---------------------------------------------------------------
0 0 us 398 255 102
1 100 us 82 88 89
2 200 us 79 57 59
3 300 us 60 63 61
4 400 us 39 37 54
5 500 us 31 24 42
6 600 us 26 30 43
7 700 us 29 20 34
8 800 us 54 47 67
9 1000 us 102 279 349
---------------------------------------------------------------
?
show oam-pm statistics session "eth-pm-service-4" dmm meas-interval 15-
mins bins interval-number 2
------------------------------------------------------------------------------
Start (UTC) : 2014/02/01 10:30:00 Status : completed
Elapsed (seconds) : 900 Suspect : no
Frames Sent : 900 Frames Received : 900
------------------------------------------------------------------------------
---------------------------------------------------------------
Frame Delay (FD) Bin Counts
---------------------------------------------------------------
Bin Lower Bound Forward Backward Round Trip
---------------------------------------------------------------
0 0 us 699 167 0
1 1000 us 169 312 456
2 2000 us 24 228 274
3 3000 us 3 136 111
4 4000 us 3 48 41
5 5000 us 1 7 10
6 6000 us 1 1 3
7 7000 us 0 1 2
8 8000 us 0 0 3
9 10000 us 0 0 0
---------------------------------------------------------------
---------------------------------------------------------------
Frame Delay Range (FDR) Bin Counts
---------------------------------------------------------------
Bin Lower Bound Forward Backward Round Trip
---------------------------------------------------------------
0 0 us 898 891 892
1 5000 us 2 9 8
---------------------------------------------------------------
---------------------------------------------------------------
Inter-Frame Delay Variation (IFDV) Bin Counts
---------------------------------------------------------------
Bin Lower Bound Forward Backward Round Trip
---------------------------------------------------------------
0 0 us 462 217 107
1 100 us 63 99 80
2 200 us 64 85 71
3 300 us 63 74 53
4 400 us 34 53 45
5 500 us 37 24 50
6 600 us 34 17 41
7 700 us 35 23 57
8 800 us 46 32 60
9 1000 us 62 276 336
---------------------------------------------------------------
?
show oam-pm statistics session "eth-pm-service-4" dmm meas-interval 15-
mins summary interval-number 2
------------------------------------------------------------------------------
Start (UTC) : 2014/02/01 10:30:00 Status : completed
Elapsed (seconds) : 900 Suspect : no
Frames Sent : 900 Frames Received : 900
------------------------------------------------------------------------------
----------------------------------------------------------------------
Bin Type Direction Minimum (us) Maximum (us) Average (us)
----------------------------------------------------------------------
FD Forward 0 6379 518
FD Backward 0 7856 2049
FD Round Trip 1118 9879 2241
FDR Forward 0 6379 518
FDR Backward 0 7856 2049
FDR Round Trip 9 8770 1132
IFDV Forward 0 6021 328
IFDV Backward 0 5800 732
IFDV Round Trip 2 7758 984
----------------------------------------------------------------------
?
show oam-pm statistics session "eth-pm-service-4" dmm meas-interval raw
------------------------------------------------------------------------------
Start (UTC) : 2014/02/01 09:43:58 Status : in-progress
Elapsed (seconds) : 3812 Suspect : yes
Frames Sent : 3812 Frames Received : 3812
------------------------------------------------------------------------------
----------------------------------------------------------------------
Bin Type Direction Minimum (us) Maximum (us) Average (us)
----------------------------------------------------------------------
FD Forward 0 11670 629
FD Backward 0 11710 2156
FD Round Trip 1109 14902 2497
FDR Forward 0 11670 617
FDR Backward 0 11710 2156
FDR Round Trip 0 13784 1360
IFDV Forward 0 10027 404
IFDV Backward 0 10436 768
IFDV Round Trip 0 13542 1056
----------------------------------------------------------------------
---------------------------------------------------------------
Frame Delay (FD) Bin Counts
---------------------------------------------------------------
Bin Lower Bound Forward Backward Round Trip
---------------------------------------------------------------
0 0 us 2815 661 0
1 1000 us 803 1287 1591
2 2000 us 127 971 1227
3 3000 us 21 639 623
4 4000 us 25 181 232
5 5000 us 12 42 72
6 6000 us 7 14 28
7 7000 us 0 4 13
8 8000 us 1 12 19
9 10000 us 1 1 7
---------------------------------------------------------------
---------------------------------------------------------------
Frame Delay Range (FDR) Bin Counts
---------------------------------------------------------------
Bin Lower Bound Forward Backward Round Trip
---------------------------------------------------------------
0 0 us 3792 3740 3751
1 5000 us 21 73 62
---------------------------------------------------------------
---------------------------------------------------------------
Inter-Frame Delay Variation (IFDV) Bin Counts
---------------------------------------------------------------
Bin Lower Bound Forward Backward Round Trip
---------------------------------------------------------------
0 0 us 1815 884 410
1 100 us 338 439 354
2 200 us 280 313 282
3 300 us 241 313 268
4 400 us 162 193 231
5 500 us 134 141 202
6 600 us 126 102 178
7 700 us 127 97 153
8 800 us 208 165 276
9 1000 us 381 1165 1458
---------------------------------------------------------------
slm
show>oam-pm>statistics>session
7210 SAS-Dxp, 7210 SAS-K 2F1C2T, 7210 SAS-K 2F6C4T, and 7210 SAS-K 3SFP+ 8C
This command displays SLM test statistics.
meas-interval raw
meas-interval {5-mins | 15-mins | 1-hour | 1-day} interval-number interval-number
show>oam-pm>statistics>session>slm
7210 SAS-Dxp, 7210 SAS-K 2F1C2T, 7210 SAS-K 2F6C4T, and 7210 SAS-K 3SFP+ 8C
This command displays measured interval statistics for SLM tests in the specified session.
Specifies raw information.
Specifies information for 5-min intervals.
Specifies information for 15-min intervals.
Specifies information for 1-hour intervals.
Specifies information for 1-day intervals.
Specifies the interval number.
The following output is an example of SLM measured interval statistics information.
Sample outputshow oam-pm statistics session "eth-pm-service-4" slm meas-interval 15-
mins interval-number 2
------------------------------------------------------------------------------
Start (UTC) : 2014/02/01 10:30:00 Status : completed
Elapsed (seconds) : 900 Suspect : no
Frames Sent : 9000 Frames Received : 9000
------------------------------------------------------------------------------
------------------------------------------------------
Frames Sent Frames Received
------------------------------------------------------
Forward 9000 9000
Backward 9000 9000
------------------------------------------------------
-------------------------------------------
Frame Loss Ratios
-------------------------------------------
Minimum Maximum Average
-------------------------------------------
Forward 0.000% 0.000% 0.000%
Backward 0.000% 0.000% 0.000%
-------------------------------------------
-------------------------------------------------------------------------------
Availability Counters (Und = Undetermined)
-------------------------------------------------------------------------------
Available Und-Avail Unavailable Und-Unavail HLI CHLI
-------------------------------------------------------------------------------
Forward 900 0 0 0 0 0
Backward 900 0 0 0 0 0
-------------------------------------------------------------------------------
show oam-pm statistics session "eth-pm-service-4" slm meas-interval raw
------------------------------------------------------------------------------
Start (UTC) : 2014/02/01 09:44:03 Status : in-progress
Elapsed (seconds) : 4152 Suspect : yes
Frames Sent : 41523 Frames Received : 41523
------------------------------------------------------------------------------
------------------------------------------------------
Frames Sent Frames Received
------------------------------------------------------
Forward 41369 41369
Backward 41369 41369
------------------------------------------------------
-------------------------------------------
Frame Loss Ratios
-------------------------------------------
Minimum Maximum Average
-------------------------------------------
Forward 0.000% 0.000% 0.000%
Backward 0.000% 0.000% 0.000%
-------------------------------------------
-------------------------------------------------------------------------------
Availability Counters (Und = Undetermined)
-------------------------------------------------------------------------------
Available Und-Avail Unavailable Und-Unavail HLI CHLI
-------------------------------------------------------------------------------
Forward 4137 0 0 0 0 0
Backward 4137 0 0 0 0 0
-------------------------------------------------------------------------------
Ib
twamp-light
show>oam-pm>statistics>session
7210 SAS-Dxp, 7210 SAS-K 2F1C2T, and 7210 SAS-K 2F6C4T
This command displays TWAMP Light test statistics.
meas-interval raw delay [{all | bins | summary}]
meas-interval raw [loss]
meas-interval {5-mins | 15-mins | 1-hour | 1-day} interval-number interval-number delay [{all | bins | summary}]
meas-interval {5-mins | 15-mins | 1-hour | 1-day} interval-number interval-number [loss]
show>oam-pm>statistics>session>twamp-light
7210 SAS-Dxp, 7210 SAS-K 2F1C2T, and 7210 SAS-K 2F6C4T
This command displays measured interval statistics for TWAMP-Light tests in the specified session
Specifies raw information.
Specifies information for 5-min intervals.
Specifies information for 15-min intervals.
Specifies information for 1-hour intervals.
Specifies information for 1-day intervals.
Specifies the interval number.
Specifies TWAMP Light delay statistics only.
Specifies TWAMP Light loss statistics only.
Specifies all information for the interval.
Specifies bin information for the interval.
Specifies summarized information for the interval.