customer [customer-id] [site customer-site-name]
show>service
Supported on all 7210 SAS platforms as described in this document
This command displays service customer information.
Displays only information for the specified customer ID.
Specifies the customer site that is the anchor point for an ingress and egress virtual scheduler hierarchy.
The following output is an example of customer information, and Table: Output fields: customer describes the output fields.
Sample output*A:ALA-12# show service customer
==========================================================
Customers
==========================================================
Customer-ID : 1
Contact : Manager
Description : Default customer
Phone : (123) 555-1212
Customer-ID : 2
Contact : Tech Support
Description : TiMetra Networks
Phone : (234) 555-1212
Customer-ID : 3
Contact : Fred
Description : TiMetra Networks
Phone : (345) 555-1212
Customer-ID : 6
Contact : Ethel
Description : Epipe Customer
Phone : (456) 555-1212
Customer-ID : 7
Contact : Lucy
Description : ABC Customer
Phone : (567) 555-1212
Customer-ID : 8
Contact : Customer Service
Description : IES Customer
Phone : (678) 555-1212
Customer-ID : 274
Contact : Mssrs. Beaucoup
Description : ABC Company
Phone : 650 123-4567
Customer-ID : 94043
Contact : Test Engineer on Duty
Description : TEST Customer
Phone : (789) 555-1212
------------------------------------------------------
Total Customers : 8
-----------------------------------------------------------
*A:ALA-12#
*A:ALA-12# show service customer 274
==============================================================================
Customer 274
==============================================================================
Customer-ID : 274
Contact : Mssrs. Beaucoup
Description : ABC Company
Phone : 650 123-4567
------------------------------------------------------------------------------
Multi Service Site
------------------------------------------------------------------------------
Site : west
Description : (Not Specified)
==============================================================================
*A:ALA-12#
*A:ALA-12# show service customer 274 site west
==============================================================================
Customer 274
==============================================================================
Customer-ID : 274
Contact : Mssrs. Beaucoup
Description : ABC Company
Phone : 650 123-4567
------------------------------------------------------------------------------
Multi Service Site
------------------------------------------------------------------------------
Site : west
Description : (Not Specified)
Assignment : Card 5
I. Sched Pol: SLA1
E. Sched Pol: (Not Specified)
------------------------------------------------------------------------------
Service Association
------------------------------------------------------------------------------
No Service Association Found.
==============================================================================
*A:ALA-12#
Label |
Description |
|---|---|
|
The ID that uniquely identifies a customer. |
|
The name of the primary contact person. |
|
Generic information about the customer. |
|
The phone/pager number to reach the primary contact person. |
|
The total number of customers configured. |
|
|
|
Multi-service site name. A multi-service customer site is a group of SAPs with common origination and termination points. |
|
Information about a specific customer multi-service site. |
|
The port ID, MDA, or card number, where the SAPs that are members of this multi-service site are defined. |
|
The ingress QoS scheduler policy assigned to this multi-service site. |
|
The egress QoS scheduler policy assigned to this multi-service site. |
|
|
|
The ID that uniquely identifies a service. |
|
Specifies the SAP assigned to the service. |
sap-using [sap sap-id]
sap-using interface [ip-address | ip-int-name]
sap-using [ingress | egress] filter filter-id
sap-using [ingress] qos-policy qos-policy-id
show>service
Supported on all 7210 SAS platforms as described in this document
This command displays SAP information.
If no optional parameters are specified, the command displays a summary of all defined SAPs. The optional parameters restrict output to only SAPs matching the specified properties.
Specifies the physical port identifier portion of the SAP definition. See Common CLI command descriptions for command syntax.
Keyword to specify matching an ingress policy.
Keyword to specify matching an egress policy.
Specifies the ingress or egress filter policy ID for which to display matching SAPs.
Keyword to specify matching SAPs with the specified IP interface.
Specifies the IP address of the interface for which to display matching SAPs.
Specifies the IP interface name for which to display matching SAPs.
The following output is an example of service SAP information, and Table: Output fields: SAP-using describes the output fields.
Sample output*A:DUT-B# show service sap-using sap 1/1/3:100.*
=========================================================================
Service Access Points
=========================================================================
PortId SvcId Ing. Ing. Egr. Adm Opr
QoS Fltr Fltr
-------------------------------------------------------------------------
1/1/1 6 1 none none Up Down
1/1/2 700 1 none none Up Down
-------------------------------------------------------------------------
Number of SAPs : 2
=========================================================================
*A:DUT-B#
Label |
Description |
|---|---|
|
The ID of the access port where the SAP is defined. |
|
The value that identifies the service. |
|
The SAP MTU value. |
|
The SAP ingress QoS policy number specified on the ingress SAP. |
|
The MAC or IP filter policy ID applied to the ingress SAP. |
|
The SAP egress QoS policy number specified on the egress SAP. |
|
The MAC or IP filter policy ID applied to the egress SAP. |
|
The accounting policy ID assigned to the SAP. |
|
The administrative state of the SAP. |
|
The actual state of the SAP. |
service-using [ies] [customer customer-id]
show>service
Supported on all 7210 SAS platforms as described in this document
This command displays the services matching certain usage properties. If no optional parameters are specified, all services defined on the system are displayed.
Display matching IES services.
Displays services only associated with the specified customer ID.
The following output is an example of service information, and Table: Output fields: service-using describes the output fields.
Sample outputA:ALA-48# show service service-using ies
===============================================================================
Services [ies]
===============================================================================
ServiceId Type Adm Opr CustomerId Last Mgmt Change
-------------------------------------------------------------------------------
88 IES Up Down 8 07/25/2006 15:46:28
89 IES Up Down 8 07/25/2006 15:46:28
104 IES Up Down 1 07/25/2006 15:46:28
200 IES Up Down 1 07/25/2006 15:46:28
214 IES Up Down 1 07/25/2006 15:46:28
321 IES Up Down 1 07/25/2006 15:46:28
322 IES Down Down 1 07/25/2006 15:46:28
1001 IES Up Down 1730 07/25/2006 15:46:28
-------------------------------------------------------------------------------
Matching Services : 8
-------------------------------------------------------------------------------
A:ALA-48#
Label |
Description |
|---|---|
|
The value that identifies the service. |
|
Specifies the service type configured for the service ID. |
|
The administrative state of the service. |
|
The operating state of the service. |
|
The ID of the customer who owns this service. |
|
The date and time of the most recent management-initiated change to this service. |
id service-id {all | arp | base | sap}
show>service
Supported on all 7210 SAS platforms as described in this document
This command displays information for a particular service-id.
Specifies the unique service identification number to identify the service in the service domain.
Displays detailed information about the service.
Displays ARP entries for the service.
Displays basic service information.
Displays SAPs associated to the service.
all
show>service>id
Supported on all 7210 SAS platforms as described in this document
This command displays detailed information for all aspects of the service.
Table: Output fields: ID all describes the all service ID command output fields.
Sample outputLabel |
Description |
|---|---|
Service Detailed Information |
|
Service Id |
The service identifier. |
VPN Id |
The number which identifies the VPN. |
Service Type |
Specifies the type of service. |
SDP Id |
The SDP identifier. |
Description |
Generic information about the service. |
Customer Id |
The customer identifier. |
Last Mgmt Change |
The date and time of the most recent management-initiated change to this customer. |
SAP Count |
The number of SAPs specified for this service. |
SDP Bind Count |
The number of SDPs bound to this service. |
Service Destination Points (SDPs) |
|
SDP Id |
The SDP identifier. |
Type |
Indicates whether this Service SDP binding is a spoke or a mesh. |
Admin Path MTU |
The largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented. |
Oper Path MTU |
The actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented. |
Delivery |
Specifies the type of delivery used by the SDP: MPLS. |
Admin State |
The administrative state of this SDP. |
Oper State |
The operational state of this SDP. |
Ingress Label |
The label used by the far-end device to send packets to this device in this service by this SDP. |
Egress Label |
The label used by this device to send packets to the far-end device in this service by this SDP. |
Ingress Filter |
The ID of the ingress filter policy. |
Egress Filter |
The ID of the egress filter policy. |
Far End |
Specifies the IP address of the remote end of the MPLS tunnel defined by this SDP. |
Last Changed |
The date and time of the most recent change to this customer. |
Signaling |
Specifies the signaling protocol used to obtain the ingress and egress labels used in frames transmitted and received on this SDP. |
Admin State |
Specifies the operating status of the service. |
Oper State |
The current status of the service. |
Hello Time |
Specifies how often the SDP echo request messages are transmitted on this SDP. |
Hello Msg Len |
Specifies the length of the SDP echo request messages transmitted on this SDP. |
Max Drop Count |
Specifies the maximum number of consecutive SDP Echo Request messages that can be unacknowledged before the keepalive protocol reports a fault. |
Hold Down Time |
Specifies the amount of time to wait before the keepalive operating status is eligible to enter the alive state. |
SDP Delivery Mechanism |
When the SDP type is MPLS, a list of LSPs used to reach the far-end router displays. All the LSPs in the list must terminate at the IP address specified in the far-end field. |
Number of SDPs |
The total number SDPs applied to this service ID. |
|
|
|
The service identifier. |
|
The ID of the access port where this SAP is defined. |
|
Generic information about the SAP. |
|
The value of the label used to identify this SAP on the access port. |
|
The desired state of the SAP. |
|
The operating state of the SAP. |
|
The date and time of the last change. |
|
The largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented. |
|
The actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented. |
|
The SAP ingress QoS policy ID. |
|
The SAP egress QoS policy ID. |
|
The SAP ingress filter policy ID. |
|
The SAP egress filter policy ID. |
|
Indicates the multi-service site that the SAP is a member. |
|
Indicates the ingress QoS scheduler for the SAP. |
|
Indicates the egress QoS scheduler for the SAP. |
|
Indicates the accounting policy applied to the SAP. |
|
Specifies whether accounting statistics are collected on the SAP. |
|
|
|
The number of packets or octets dropped. |
|
The number of high priority packets, as determined by the SAP ingress QoS policy. |
|
The number of low priority packets, as determined by the SAP ingress QoS policy. |
|
The number of in-profile packets or octets (rate below CIR) forwarded. |
|
The number of out-of-profile packets or octets (rate above CIR) forwarded. |
arp [ip-address] | [mac ieee-address] | [sap sap-id] | [interface ip-int-name]
show>service>id
Supported on all 7210 SAS platforms as described in this document
Displays the ARP table for the IES instance. The ARP entries for a subscriber interface are displayed uniquely. Each MAC associated with the subscriber interface child group-interfaces are displayed with each subscriber interface ARP entry. They do not reflect actual ARP entries but are displayed along the interfaces ARP entry for easy lookup.
Specifies the IP address of the interface for which to display matching ARP entries.
Displays only ARP entries in the ARP table with the specified 48-bit MAC address. The MAC address can be expressed in the form aa:bb:cc:dd:ee:ff or aa-bb-cc-dd-ee-ff, where aa, bb, cc, dd, ee and ff are hexadecimal numbers.
Displays SAP information for the specified SAP ID. See Common CLI command descriptions for command syntax.
Specifies matching service ARP entries associated with the IP interface.
Specifies the IP interface name for which to display matching ARPs.
The following output is an example of ARP information, and Table: Output fields: ARP describes the output fields.
Sample output*A:DUT-B# show service id 100 arp
==============================================================================
ARP Table
===============================================================================
IP Address MAC Address Type Expiry Interface SAP
-------------------------------------------------------------------------------
192.168.1.2 00:00:01:00:00:01 Other 00h00m00s HW 1/1/1:10*
192.168.1.1 32:67:01:01:00:03 Other 00h00m00s to7x 1/1/3:10*
192.168.2.2 32:68:01:01:00:02 Dynamic 03h59m58s to7x 1/1/3:10*
===============================================================================
*A:DUT-B#
Label |
Description |
|---|---|
|
The IP address. |
|
The specified MAC address. |
|
Static — FDB entries created by management. Learned — Dynamic entries created by the learning process. Other — Local entries for the IP interfaces created. |
|
The age of the ARP entry. |
|
The interface applied to the service. |
|
The SAP ID. |
base
show>service>id
Supported on all 7210 SAS platforms as described in this document
This command displays basic information about this IES service.
The following output is an example of basic IES service information, and Table: Output fields: base describes the output fields.
Sample output*A:ALA-A# show service id 100 base
---------------------------------------------------------------
Service Basic Information
---------------------------------------------------------------
Service Id : 100 Vpn Id : 100
Service Type : IES
Description : Default Ies description for service id 100
Customer Id : 1
Last Status Change: 08/29/2006 17:44:28
Last Mgmt Change : 08/29/2006 17:44:28
Admin State : Up Oper State : Up
SAP Count : 2
-------------------------------------------------------------------------------
Service Access & Destination Points
-------------------------------------------------------------------------------
Identifier Type AdmMTU OprMTU Adm Opr
-------------------------------------------------------------------------------
sap:1/1/3 null 1514 1514 Up Up
sap:1/1/4 null 1514 1514 Up Up
===============================================================================
*A:ALA-A#
Label |
Description |
|---|---|
Service Id |
Displays the service identifier. |
VPN Id |
Displays the VPN identifier. |
Service Type |
Displays the type of service. |
Description |
Displays generic information about the service. |
Customer Id |
Displays the customer identifier. |
Last Status Change |
Displays the date and time of the most recent status change. |
Last Mgmt Change |
Displays the date and time of the most recent management-initiated change to this customer. |
Admin State |
The administrative state of the service. |
Oper State |
The operational state of the service. |
SAP Count |
The number of SAPs defined on the service. |
Identifier |
Specifies the service access ID (SAP). |
Type |
The type of SAPs allowed in the service. It also describes the applied processing by the node to the packets received on these SAPs. |
AdminMTU |
The largest frame size (in octets) that the SAP can handle. |
OprMTU |
Specifies the actual largest service frame size (in octets) that can be transmitted through this port, without requiring the packet to be fragmented. |
Admin |
The administrative state of the SAP. |
Opr |
The operating state of the SAP. |
interface [ip-address | ip-int-name] [detail | summary]
show>service>id
Supported on all 7210 SAS platforms as described in this document
This command displays information for the IP interfaces associated with the IES service. If no optional parameters are specified, a summary of all IP interfaces associated to the service are displayed.
Specifies the IP address of the interface for which to display information.
Specifies the IP interface name for which to display information.
Displays detailed IP interface information.
Displays the summary of IP interface information.
The following output is an example of service interface information, and Table: Output fields: service ID interface describes the output fields.
Sample outputA:ALA-49# show service id 88 interface
===============================================================================
Interface Table
===============================================================================
Interface-Name Adm Opr(v4/v6) Type Port/SapId
IP-Address PfxState
-------------------------------------------------------------------------------
Sector A Up Down/Down IES 1/1/1.2.2
- -
test Up Down/Down IES 1/1/2:0
10.1.1.1/31 n/a
10.1.1.1/31 n/a
10.1.2.1/31 n/a
test27 Up Up/-- IES Sub subscriber
192.168.10.21/24 n/a
grp-if Up Down/-- IES Grp 1/2/2
Interfaces : 4
===============================================================================
A:ALA-49#
A:ALA-49# show service id 88 interface
===============================================================================
Interface Table
===============================================================================
Interface-Name Adm Opr(v4/v6) Type Port/SapId
IP-Address PfxState
-------------------------------------------------------------------------------
Sector A Up Down/Down IES 1/1/1.2.2
- -
test Up Down/Down IES 1/1/2:0
10.1.1.1/31 n/a
10.1.1.1/31 n/a
10.1.2.1/31 n/a
test27 Up Up/-- IES Sub subscriber
192.168.10.21/24 n/a
grp-if Up Down/-- IES Grp 1/2/2
Interfaces : 4
===============================================================================
A:ALA-49#
Label |
Description |
|---|---|
|
The name used to refer to the IES interface. |
|
Specifies the interface type. |
|
Specifies the IP address/IP subnet/broadcast address of the interface. |
|
The administrative state of the interface. |
|
The operational state of the interface. |
|
The administrative state of the interface. |
|
The operational state of the interface. |
|
Specifies the IP address/IP subnet/broadcast address of the interface. |
|
The index corresponding to this IES interface. The primary index is 1; all IES interfaces are defined in the base virtual router context. |
|
Specifies the interface type. |
|
Specifies the SAP port ID. |
|
Specifies whether SNTP broadcast client mode is enabled or disabled. |
|
Specifies the timeout for an ARP entry learned on the interface. |
|
Specifies the 48-bit IEEE 802.3 MAC address. |
|
Specifies whether ICMP mask reply is enabled or disabled. |
|
Specifies whether cflowd collection and analysis on the interface is enabled or disabled. |
|
Specifies the rate for ICMP redirect messages. |
|
Specifies the rate for ICMP unreachable messages. |
|
Specifies the rate for ICMP TTL messages. |