DSCP marking CPU self-generated traffic

The user can configure DSCP marking for CPU-generated traffic on the 7210 SAS-K 2F6C4T and 7210 SAS-K 3SFP+ 8C platforms only. See QoS for CPU self-generated traffic on network interfaces for the 7210 SAS-K 2F6C4T and 7210 SAS-K 3SFP+ 8C for more information about QoS for self-generated (CPU) traffic on the 7210 SAS-K 2F6C4T and 7210 SAS-K 3SFP+ 8C. The following table lists the default DSCP and dot1p marking values for the 7210 SAS-K 2F1C2T.

Note:

Protocols such as BGP, RSVP, TLDP, OSPF, and IS-IS are not supported on 7210 SAS devices configured in access-uplink mode.

Table: DSCP and dot1p Marking for 7210 SAS-K 2F1C2T

Protocol

IPv4

DSCP marking

dot1p marking

Default FC

DSCP values

dot1p values

ARP

NA

NA

Yes

NC

-

7

CFM

NA

NA

Yes

NC

-

7

FTP

Yes

Yes

Yes

H2

34

4

ICMP ping

Yes

Yes

Yes

NC

0

7

ICMP Req

Yes

Yes

Yes

NC

0

7

ICMP Res

Yes

Yes

Yes

NC

0

7

ICMP Unreach

Yes

Yes

Yes

NC

0

7

IGMP

Yes

Yes

Yes

NC

48

7

NTP

Yes

Yes

Yes

H2

48

7

PTP

Yes

Yes

Yes

H2

48

7

RADIUS

Yes

Yes

Yes

H2

34

4

SCP

NA

NA

Yes

H2

34

4

SNMP

Yes

Yes

Yes

H2

34

4

SNMP trap/log

Yes

Yes

Yes

H2

34

4

SSH

Yes

Yes

Yes

H2

34

7

STP

NA

NA

Yes

NC

-

7

SYSLOG

Yes

Yes

Yes

H2

34

4

TACACS

Yes

Yes

Yes

H2

34

4

TACPLUS

Yes

Yes

Yes

H2

34

4

TELNET

Yes

Yes

Yes

H2

34

4

TFTP

Yes

Yes

Yes

H2

34

4

Trace route

Yes

Yes

Yes

NC

0

7

The following table lists the default DSCP and dot1p marking values for the 7210 SAS-K 2F6C4T and 7210 SAS-K 3SFP+ 8C.

Note:

DSCP and dot1p values in Table: DSCP and dot1p marking for 7210 SAS-K 2F6C4T and 7210 SAS-K 3SFP+ 8C are applicable when remarking is disabled on the egress service object (for example, access port, SAP, and network port) used to send out the packets.

Table: DSCP and dot1p marking for 7210 SAS-K 2F6C4T and 7210 SAS-K 3SFP+ 8C

Protocol

IPv4

DSCP marking

dot1p marking

Default FC

DSCP values (decimal)

dot1p values

OSPF

Yes

Yes

Yes

NC

48

7

ISIS

Yes

No

Yes

NC

-

7

TLDP

Yes

Yes

Yes

NC

48

7

RSVP

Yes

Yes

Yes

NC

48

7

SNMP

Yes

Yes

Yes

H2

34

4

NTP

Yes

Yes

Yes

NC

48

7

TELNET

Yes

Yes

Yes

H2

34

4

FTP

Yes

Yes

Yes

H2

34

4

TFTP

Yes

Yes

Yes

H2

34

4

SYSLOG

Yes

Yes

Yes

H2

34

4

TACACS

Yes

Yes

Yes

H2

34

4

RADIUS

Yes

Yes

Yes

NC

48

7

SSH

Yes

Yes

Yes

H2

34

4

ICMP Req

Yes

Yes

Yes

NC

0

7

ICMP Res

Yes

Yes

Yes

NC

0

7

ICMP Unreach

Yes

Yes

Yes

NC

0

7

SCP

Yes

Yes

Yes

H2

34

4

PIM (SSM)

Yes

Yes

Yes

NC

48

7

STP

NA

NA

Yes

NC

-

7

CFM

NA

NA

Yes

NC

-

7

ARP

NA

NA

Yes

NC

-

7

Trace route

Yes

Yes

Yes

NC

0

7

TACPLUS

Yes

Yes

Yes

H2

34

4

IGMP

Yes

Yes

Yes

NC

48

7

DNS

Yes

Yes

Yes

H2

34

4

BGP

Yes

Yes

Yes

NC

48

7

PTP (see note) 1

Yes

Yes

Yes

see note 1

see note 1

7

1 Based on the type of the PTP message, that is, PTP event messages (for example, Sync message) and PTP non-event messages (for example, Announce, Follow-up), the DSCP value used is either 0x30 (h1) or 0x38 (nc), and the dot1p value is always 7.