interface [ip-int-name | ip-address] statistics [detail]
show>router>rsvp
Supported on all 7210 SAS platforms as described in this document
This command shows RSVP interfaces.
Specifies the name of the network IP interface. An interface name cannot be in the form of an IP address. If the string contains special characters (#, $, spaces, and so on), the entire string must be enclosed within double quotes.
Specifies the system or network interface IP address.
Displays IP address and the number of packets sent and received on an interface-basis.
Displays detailed information.
The following output is an example of RSVP interface information, and Table: Output fields: RSVP interface describes the fields.
Sample output*A:A:ALA-1>show>router>rsvp# interface detail
===============================================================================
RSVP Interfaces (Detailed)
===============================================================================
-------------------------------------------------------------------------------
Interface : system
-------------------------------------------------------------------------------
Interface : system
Port ID : system
Admin State : Up Oper State : Up
Active Sessions : 0 Active Resvs : 0
Total Sessions : 0
Subscription : 100 % Port Speed : 0 Mbps
Total BW : 0 Mbps Aggregate : Dsabl
Hello Interval : 3000 ms Hello Timeouts : 0
Authentication : Disabled
Auth Rx Seq Num : n/a Auth Key Id : n/a
Auth Tx Seq Num : n/a Auth Win Size : n/a
Refresh Reduc. : Disabled Reliable Deli. : Disabled
Bfd Enabled : No Graceful Shut. : Disabled
Percent Link Bandwidth for Class Types
Link Bw CT0 : 100 Link Bw CT4 : 0
Link Bw CT1 : 0 Link Bw CT5 : 0
Link Bw CT2 : 0 Link Bw CT6 : 0
Link Bw CT3 : 0 Link Bw CT7 : 0
Bandwidth Constraints for Class Types (Kbps)
BC0 : 0 BC4 : 0
BC1 : 0 BC5 : 0
BC2 : 0 BC6 : 0
BC3 : 0 BC7 : 0
Bandwidth for TE Class Types (Kbps)
TE0-> Resv. Bw : 0 Unresv. Bw : 0
TE1-> Resv. Bw : 0 Unresv. Bw : 0
TE2-> Resv. Bw : 0 Unresv. Bw : 0
TE3-> Resv. Bw : 0 Unresv. Bw : 0
TE4-> Resv. Bw : 0 Unresv. Bw : 0
TE5-> Resv. Bw : 0 Unresv. Bw : 0
TE6-> Resv. Bw : 0 Unresv. Bw : 0
TE7-> Resv. Bw : 0 Unresv. Bw : 0
No Neighbors.
-------------------------------------------------------------------------------
Interface : ip-10.10.12.3
-------------------------------------------------------------------------------
Interface : ip-10.10.12.3
Port ID : 1/1/9
Admin State : Up Oper State : Up
Active Sessions : 1 Active Resvs : 0
Total Sessions : 1
Subscription : 100 % Port Speed : 1000 Mbps
Total BW : 1000 Mbps Aggregate : Dsabl
Hello Interval : 3000 ms Hello Timeouts : 0
Authentication : Disabled
Auth Rx Seq Num : n/a Auth Key Id : n/a
Auth Tx Seq Num : n/a Auth Win Size : n/a
Refresh Reduc. : Disabled Reliable Deli. : Disabled
Bfd Enabled : No Graceful Shut. : Disabled
Percent Link Bandwidth for Class Types
Link Bw CT0 : 100 Link Bw CT4 : 0
Link Bw CT1 : 0 Link Bw CT5 : 0
Link Bw CT2 : 0 Link Bw CT6 : 0
Link Bw CT3 : 0 Link Bw CT7 : 0
Bandwidth Constraints for Class Types (Kbps)
BC0 : 1000000 BC4 : 0
BC1 : 0 BC5 : 0
BC2 : 0 BC6 : 0
BC3 : 0 BC7 : 0
Bandwidth for TE Class Types (Kbps)
TE0-> Resv. Bw : 0 Unresv. Bw : 1000000
TE1-> Resv. Bw : 0 Unresv. Bw : 1000000
TE2-> Resv. Bw : 0 Unresv. Bw : 1000000
TE3-> Resv. Bw : 0 Unresv. Bw : 1000000
TE4-> Resv. Bw : 0 Unresv. Bw : 1000000
TE5-> Resv. Bw : 0 Unresv. Bw : 1000000
TE6-> Resv. Bw : 0 Unresv. Bw : 1000000
TE7-> Resv. Bw : 0 Unresv. Bw : 1000000
Neighbors : 10.10.12.2
-------------------------------------------------------------------------------
Interface : ip-10.10.4.3
-------------------------------------------------------------------------------
Interface : ip-10.10.4.3
Port ID : 1/1/8
Admin State : Up Oper State : Up
Active Sessions : 1 Active Resvs : 0
Total Sessions : 1
Subscription : 100 % Port Speed : 1000 Mbps
Total BW : 1000 Mbps Aggregate : Dsabl
Hello Interval : 3000 ms Hello Timeouts : 0
Authentication : Disabled
Auth Rx Seq Num : n/a Auth Key Id : n/a
Auth Tx Seq Num : n/a Auth Win Size : n/a
Refresh Reduc. : Disabled Reliable Deli. : Disabled
Bfd Enabled : No Graceful Shut. : Disabled
Percent Link Bandwidth for Class Types
Link Bw CT0 : 100 Link Bw CT4 : 0
Link Bw CT1 : 0 Link Bw CT5 : 0
Link Bw CT2 : 0 Link Bw CT6 : 0
Link Bw CT3 : 0 Link Bw CT7 : 0
Bandwidth Constraints for Class Types (Kbps)
BC0 : 1000000 BC4 : 0
BC1 : 0 BC5 : 0
BC2 : 0 BC6 : 0
BC3 : 0 BC7 : 0
Bandwidth for TE Class Types (Kbps)
TE0-> Resv. Bw : 0 Unresv. Bw : 1000000
TE1-> Resv. Bw : 0 Unresv. Bw : 1000000
TE2-> Resv. Bw : 0 Unresv. Bw : 1000000
TE3-> Resv. Bw : 0 Unresv. Bw : 1000000
TE4-> Resv. Bw : 0 Unresv. Bw : 1000000
TE5-> Resv. Bw : 0 Unresv. Bw : 1000000
TE6-> Resv. Bw : 0 Unresv. Bw : 1000000
TE7-> Resv. Bw : 0 Unresv. Bw : 1000000
Neighbors : 10.10.4.2
-------------------------------------------------------------------------------
Interface : ip-10.10.2.3
-------------------------------------------------------------------------------
Interface : ip-10.10.2.3
Port ID : 1/1/4
Admin State : Up Oper State : Down
Active Sessions : 0 Active Resvs : 0
Total Sessions : 0
Subscription : 100 % Port Speed : 0 Mbps
Total BW : 0 Mbps Aggregate : Dsabl
Hello Interval : 3000 ms Hello Timeouts : 0
Authentication : Disabled
Auth Rx Seq Num : n/a Auth Key Id : n/a
Auth Tx Seq Num : n/a Auth Win Size : n/a
Refresh Reduc. : Disabled Reliable Deli. : Disabled
Bfd Enabled : No Graceful Shut. : Disabled
Percent Link Bandwidth for Class Types
Link Bw CT0 : 100 Link Bw CT4 : 0
Link Bw CT1 : 0 Link Bw CT5 : 0
Link Bw CT2 : 0 Link Bw CT6 : 0
Link Bw CT3 : 0 Link Bw CT7 : 0
Bandwidth Constraints for Class Types (Kbps)
BC0 : 0 BC4 : 0
BC1 : 0 BC5 : 0
BC2 : 0 BC6 : 0
BC3 : 0 BC7 : 0
Bandwidth for TE Class Types (Kbps)
TE0-> Resv. Bw : 0 Unresv. Bw : 0
TE1-> Resv. Bw : 0 Unresv. Bw : 0
TE2-> Resv. Bw : 0 Unresv. Bw : 0
TE3-> Resv. Bw : 0 Unresv. Bw : 0
TE4-> Resv. Bw : 0 Unresv. Bw : 0
TE5-> Resv. Bw : 0 Unresv. Bw : 0
TE6-> Resv. Bw : 0 Unresv. Bw : 0
TE7-> Resv. Bw : 0 Unresv. Bw : 0
No Neighbors.
===============================================================================
Label |
Description |
|---|---|
Interface |
The name of the IP interface |
Total Sessions |
The total number of RSVP sessions on this interface This count includes sessions that are active, as well as sessions that have been signaled but a response has not yet been received. |
Active Sessions |
The total number of active RSVP sessions on this interface |
Total BW |
The amount of bandwidth in megabits per second (mbps) available to be reserved for the RSVP protocol on the interface |
Resv BW |
The amount of bandwidth in mega-bits per seconds (mbps) reserved on this interface A value of zero indicates that no bandwidth is reserved. |
Adm |
Down — The RSVP interface is administratively disabled Up — The RSVP interface is administratively enabled |
Opr |
Down — The RSVP interface is operationally down Up — The RSVP interface is operationally up |
Port ID |
Specifies the physical port bound to the interface |
Active Resvs |
The total number of active RSVP sessions that have reserved bandwidth |
Subscription |
Specifies the percentage of the link bandwidth that RSVP can use for reservation When the value is zero, no new sessions are permitted on this interface. |
Port Speed |
Specifies the speed for the interface |
Unreserved BW |
Specifies the amount of unreserved bandwidth |
Reserved BW |
Specifies the amount of bandwidth in megabits per second (mbps) reserved by the RSVP session on this interface A value of zero indicates that no bandwidth is reserved. |
Total BW |
Specifies the amount of bandwidth in megabits per second (mbps) available to be reserved for the RSVP protocol on this interface |
Hello Interval |
Specifies the length of time, in seconds, between the hello packets that the router sends on the interface This value must be the same for all routers attached to a common network. When the value is zero, the sending of hello messages is disabled. |
Refresh Time |
Specifies the interval between the successive path and resv refresh messages RSVP declares the session down after it misses ((keep-multiplier + 0.5) ✕ 1.5 ✕ refresh-time)) consecutive refresh messages. |
Hello Timeouts |
The total number of hello messages that timed out on this RSVP interface |
Neighbors |
The IP address of the RSVP neighbor |
Sent |
The total number of error free RSVP packets that have been transmitted on the RSVP interface |
Recd |
The total number of error free RSVP packets received on the RSVP interface |
Total Packets |
The total number of RSVP packets, including errors, received on the RSVP interface |
Bad Packets |
The total number of RSVP packets with errors transmitted on the RSVP interface |
Paths |
The total number of RSVP PATH messages received on the RSVP interface |
Path Errors |
The total number of RSVP PATH ERROR messages transmitted on the RSVP interface |
Path Tears |
The total number of RSVP PATH TEAR messages received on the RSVP interface |
Resvs |
The total number of RSVP RESV messages received on the RSVP interface |
Resv Confirms |
The total number of RSVP RESV CONFIRM messages received on the RSVP interface |
Resv Errors |
Total RSVP RESV ERROR messages received on RSVP interface |
Resv Tears |
Total RSVP RESV TEAR messages received on RSVP interface |
Refresh Summaries |
Total RSVP RESV summary refresh messages received on interface |
Refresh Acks |
Total RSVP RESV acknowledgment messages received when refresh reduction is enabled on the RSVP interface |
Hellos |
Total RSVP RESV HELLO REQ messages received on the interface |
Bfd Enabled |
Yes — BFD is enabled on the RSVP interface No — BFD is disabled on the RSVP interface |
neighbor [ip-address] [detail]
show>router>rsvp
Supported on all 7210 SAS platforms as described in this document
This command shows neighbor information.
Displays RSVP information about the specified IP address.
Displays detailed information.
session session-type [from ip-address | to ip-address| lsp-name name] [status {up | down}] [detail]
show>router>rsvp
Supported on all 7210 SAS platforms as described in this document
This command shows RSVP session information.
Specifies the session type.
Specifies the IP address of the originating router.
Specifies the IP address of the egress router.
Specifies the name of the LSP used in the path.
Displays a session that is operationally up.
Displays a session that is operationally down.
Displays detailed information.
The following output is an example of RSVP session information, and Table: Output fields: RSVP session describes the output fields.
Sample output*A:SRU4>show>router>rsvp# session
===============================================================================
RSVP Sessions
===============================================================================
From To Tunnel LSP Name State
ID ID
-------------------------------------------------------------------------------
10.20.1.5 10.20.1.4 18 27648 b4-1::b4-1 Up
10.20.1.5 10.20.1.4 1 37902 gsr::gsr Up
10.20.1.5 10.20.1.22 11 53760 to_10_20_1_22_cspf::to_10_2* Up
10.20.1.4 10.20.1.20 146 17920 to_10_20_1_20_cspf_3::to_10* Up
10.20.1.4 10.20.1.20 145 34816 to_10_20_1_20_cspf_2::to_10* Up
10.20.1.4 10.20.1.20 147 45056 to_10_20_1_20_cspf_4::to_10* Up
10.20.1.4 10.20.1.20 148 6656 to_10_20_1_20_cspf_5::to_10* Up
10.20.1.4 10.20.1.20 149 58880 to_10_20_1_20_cspf_6::to_10* Up
10.20.1.4 10.20.1.20 150 13312 to_10_20_1_20_cspf_7::to_10* Up
10.20.1.4 10.20.1.20 152 40448 to_10_20_1_20_cspf_9::to_10* Up
10.20.1.4 10.20.1.20 154 27648 to_10_20_1_20_cspf_11::to_1* Up
10.20.1.4 10.20.1.20 155 12288 to_10_20_1_20_cspf_12::to_1* Up
10.20.1.4 10.20.1.20 151 46080 to_10_20_1_20_cspf_8::to_10* Up
10.20.1.4 10.20.1.20 153 512 to_10_20_1_20_cspf_10::to_1* Up
10.20.1.4 10.20.1.22 164 62464 to_10_20_1_22_cspf_2::to_10* Up
10.20.1.4 10.20.1.20 156 37888 to_10_20_1_20_cspf_13::to_1* Up
10.20.1.4 10.20.1.20 157 24064 to_10_20_1_20_cspf_14::to_1* Up
10.20.1.4 10.20.1.20 158 19968 to_10_20_1_20_cspf_15::to_1* Up
10.20.1.4 10.20.1.20 161 59904 to_10_20_1_20_cspf_18::to_1* Up
...
10.20.1.3 10.20.1.4 54 23088 to_110_20_1_4_cspf_4::to_11* Up
-------------------------------------------------------------------------------
Sessions : 1976
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:SRU4>show>router>rsvp#
A:ALA-12# show router rsvp session lsp-name A_C_2::A_C_2 status up
===============================================================================
RSVP Sessions
===============================================================================
From To Tunnel LSP Name State
ID ID
-------------------------------------------------------------------------------
10.20.1.1 10.20.1.3 2 40 A_C_2::A_C_2 Up
-------------------------------------------------------------------------------
Sessions : 1
===============================================================================
A:ALA-12#
Label |
Description |
|---|---|
From |
The IP address of the originating router |
To |
The IP address of the egress router |
Tunnel ID |
The IP address of the tunnel’s ingress node supporting this RSVP session |
LSP ID |
The ID assigned by the agent to this RSVP session |
Name |
The administrative name assigned to the RSVP session by the agent |
State |
Down — the operational state of this RSVP session is down Up — the operational state of this RSVP session is up |
statistics
show>router>rsvp
Supported on all 7210 SAS platforms as described in this document
This command displays global statistics in the RSVP instance.
The following output is an example of RSVP statistics information, and Table: Output fields: RSVP statistics describes the output fields.
Sample output*A:SRU4>show>router>rsvp# statistics
===============================================================================
RSVP Global Statistics
===============================================================================
PATH Timeouts : 1026 RESV Timeouts : 182
===============================================================================
*A:SRU4>show>router>rsvp#
Label |
Description |
|---|---|
PATH Timeouts |
The total number of path timeouts |
RESV Timeouts |
The total number of RESV timeouts |
rsvp status
show>router>rsvp
Supported on all 7210 SAS platforms as described in this document
This command displays RSVP status.
The following output is an example of RSVP status information, and Table: Output fields: RSVP status describes the output fields.
Sample output*A:SRU4>show>router>rsvp# status
===============================================================================
RSVP Status
===============================================================================
Admin Status : Up Oper Status : Up
Keep Multiplier : 3 Refresh Time : 30 sec
Message Pacing : Disabled Pacing Period : 100 msec
Max Packet Burst : 650 msgs Refresh Bypass : Disabled
===============================================================================
*A:SRU4>show>router>rsvp#
Label |
Description |
|---|---|
|
|
|
|
|
Displays the keep-multiplier number used by RSVP to declare that a reservation is down or the neighbor is down |
|
Displays the refresh-time interval, in seconds, between the successive Path and Resv refresh messages |
|
|
|
Displays the time interval, in milliseconds, when the router can send the specified number of RSVP messages specified in the rsvp max-burst command |
|
Displays the maximum number of RSVP messages that are sent in the specified period under normal operating conditions |