isis all
isis [isis-instance]
show>router
Supported on all 7210 SAS platforms as described in this document
This command displays information for a specified IS-IS instance.
Specifies the instance ID for an IS-IS instance.
adjacency [ip-int-name | ip-address | nbr-system-id] [detail]
show>router>isis
Supported on all 7210 SAS platforms as described in this document
This command displays information about IS-IS neighbors. If no parameters are specified, all adjacencies are displayed. If detail is specified, operational and statistical information is displayed.
Specifies the IP interface name. An interface name cannot be in the form of an IP address. Interface names can be any string up to 32 characters composed of printable, 7-bit ASCII characters. If the string contains special characters (such as #, $, and spaces), the entire string must be enclosed within double quotes.
Specifies the interface IP address.
Displays only the adjacency with the specified system ID.
Displays detailed information about the adjacency.
The following output is an example of ISIS adjacency information, and Table: Output fields: ISIS adjacency describes the output fields.
Sample output*A:Dut-A# show router isis adjacency
===============================================================================
Router Base ISIS Instance 1 Adjacency
===============================================================================
System ID Usage State Hold Interface MT Enab
-------------------------------------------------------------------------------
Dut-B L1 Up 2 ip-3FFE::A0A:101 Yes
Dut-B L2 Up 2 ip-3FFE::A0A:101 Yes
Dut-F L1L2 Up 5 ies-1-3FFE::A0A:1501 Yes
-------------------------------------------------------------------------------
Adjacencies : 3
===============================================================================
*A:Dut-A#
*A:ALA-A# show router isis adjacency 180.0.7.12
===============================================================================
Router Base ISIS Instance 1 Adjacency
===============================================================================
System ID Usage State Hold Interface
-------------------------------------------------------------------------------
asbr_east L2 Up 25 if2/5
-------------------------------------------------------------------------------
Adjacencies : 1
===============================================================================
*A:ALA-A#
*A:ALA-A# show router isis adjacency if2/5
===============================================================================
Router Base ISIS Instance 1 Adjacency
===============================================================================
System ID Usage State Hold Interface
-------------------------------------------------------------------------------
asbr_east L2 Up 20 if2/5
-------------------------------------------------------------------------------
Adjacencies : 1
===============================================================================
*A:ALA-A#
*A:Dut-A# show router isis adjacency detail
===============================================================================
Router Base ISIS Instance 1 Adjacency
===============================================================================
SystemID : Dut-B SNPA : 20:81:01:01:00:01
Interface : ip-3FFE::A0A:101 Up Time : 0d 00:56:10
State : Up Priority : 64
Nbr Sys Typ : L1 L. Circ Typ : L1
Hold Time : 2 Max Hold : 2
Adj Level : L1 MT Enabled : Yes
IPv4 Neighbor : 10.10.1.2
Restart Support : Disabled
Restart Status : Not currently being helped
Restart Supressed : Disabled
Number of Restarts: 0
Last Restart at : Never
SystemID : Dut-B SNPA : 20:81:01:01:00:01
Interface : ip-3FFE::A0A:101 Up Time : 0d 00:56:10
State : Up Priority : 64
Nbr Sys Typ : L2 L. Circ Typ : L2
Hold Time : 2 Max Hold : 2
Adj Level : L2 MT Enabled : Yes
Topology : Unicast
IPv4 Neighbor : 10.10.1.2
Restart Support : Disabled
Restart Status : Not currently being helped
Restart Supressed : Disabled
Number of Restarts: 0
Last Restart at : Never
SystemID : Dut-F SNPA : 00:00:00:00:00:00
Interface : ies-1-3FFE::A0A:1501 Up Time : 0d 01:18:34
State : Up Priority : 0
Nbr Sys Typ : L1L2 L. Circ Typ : L1L2
Hold Time : 5 Max Hold : 6
Adj Level : L1L2 MT Enabled : Yes
Topology : Unicast
IPv4 Neighbor : 10.10.21.6
Restart Support : Disabled
Restart Status : Not currently being helped
Restart Supressed : Disabled
Number of Restarts: 0
Last Restart at : Never
===============================================================================
*A:Dut-A#
A:Dut-A# show router isis status
===============================================================================
Router Base ISIS Instance 1 Status
===============================================================================
System Id : 0100.2000.1001
Admin State : Up
Ipv4 Routing : Enabled
Last Enabled : 08/28/2006 10:22:17
Level Capability : L2
Authentication Check : True
Authentication Type : None
CSNP-Authentication : Enabled
HELLO-Authentication : Enabled
PSNP-Authentication : Enabled
Traffic Engineering : Enabled
Graceful Restart : Disabled
GR Helper Mode : Disabled
LSP Lifetime : 1200
LSP Wait : 1 sec (Max) 1 sec (Initial) 1 sec (Second)
Adjacency Check : loose
L1 Auth Type : none
L2 Auth Type : none
L1 CSNP-Authenticati*: Enabled
L1 HELLO-Authenticat*: Enabled
L1 PSNP-Authenticati*: Enabled
L1 Preference : 15
L2 Preference : 18
L1 Ext. Preference : 160
L2 Ext. Preference : 165
L1 Wide Metrics : Disabled
L2 Wide Metrics : Enabled
L1 LSDB Overload : Disabled
L2 LSDB Overload : Disabled
L1 LSPs : 0
L2 LSPs : 15
Last SPF : 08/28/2006 10:22:25
SPF Wait : 1 sec (Max) 10 ms (Initial) 10 ms (Second)
Export Policies : None
Area Addresses : 49.0001
===============================================================================
* indicates that the corresponding row element may have been truncated.
A:Dut-A#
Label |
Description |
|---|---|
Interface |
Displays the interface name associated with the neighbor |
System-id |
Displays the neighbor system ID |
Level |
Displays the level: L1 only, L2 only, L1 and L2 |
State |
Displays the state: Up, down, new, one-way, initializing, or rejected |
Hold |
Displays the hold time remaining for the adjacency |
SNPA |
Displays the subnetwork point of attachment (MAC address of the next hop) |
Circuit type |
Displays the level on the interface: L1, L2, or both |
Expires In |
Displays the number of seconds until adjacency expires |
Priority |
Displays the priority to become designated router |
Up/down transitions |
Displays the number of times the neighbor state has changed |
Event |
Displays the event causing the last transition |
Last transition |
Displays the amount of time since last transition change |
Speaks |
Displays supported protocols (only IP) |
IP address |
Displays the IP address of the neighbor |
MT enab |
Yes — The neighbor is advertising at least 1 non MTID#0 |
Topology |
Derived from the MT TLV in the IIH
Not supported MTID's => Topology line suppressed |
capabilities [system-id | lsp-id] [level level]
show>router>isis
Supported on all 7210 SAS platforms as described in this document
This command displays IS-IS capability information.
Displays only the IS-IS capabilities related to the specified system ID. If no parameters are specified, all database entries are displayed.
Displays only IS-IS capabilities related to the specified LSP ID. If no system ID or LSP ID is specified, all database entries are displayed.
Displays the interface level capabilities (1, 2, or 1 and 2).
The following output is an example of IS-IS capability information, and Table: Output fields: IS-IS capabilities describes the output fields.
Sample output*A:Dut-C# show router isis capabilities
===============================================================================
Rtr Base ISIS Instance 0 Capabilities
===============================================================================
Displaying Level 1 capabilities
-------------------------------------------------------------------------------
LSP ID : Dut-A.00-00
Router Cap : 10.20.1.1, D:0, S:0
TE Node Cap : B E M P
SR Cap: IPv4 MPLS-IPv6
SRGB Base:20000, Range:20000
SR Alg: metric based SPF
LSP ID : Dut-A.02-00
LSP ID : Dut-A.03-00
LSP ID : Dut-B.00-00
Router Cap : 10.20.1.2, D:0, S:0
TE Node Cap : B E M P
SR Cap: IPv4 MPLS-IPv6
SRGB Base:20000, Range:20000
SR Alg: metric based SPF
LSP ID : Dut-C.00-00
Router Cap : 10.20.1.3, D:0, S:0
TE Node Cap : B E M P
SR Cap: IPv4 MPLS-IPv6
SRGB Base:20000, Range:20000
SR Alg: metric based SPF
LSP ID : Dut-C.02-00
LSP ID : Dut-D.00-00
Router Cap : 10.20.1.4, D:0, S:0
TE Node Cap : B E M P
SR Cap: IPv4 MPLS-IPv6
SRGB Base:20000, Range:20000
SR Alg: metric based SPF
LSP ID : Dut-D.01-00
LSP ID : Dut-E.00-00
Router Cap : 10.20.1.5, D:0, S:0
TE Node Cap : B E M P
SR Cap: IPv4 MPLS-IPv6
SRGB Base:20000, Range:20000
SR Alg: metric based SPF
LSP ID : Dut-E.01-00
LSP ID : Dut-E.02-00
LSP ID : Dut-F.00-00
Router Cap : 10.20.1.6, D:0, S:0
TE Node Cap : B E M P
SR Cap: IPv4 MPLS-IPv6
SRGB Base:20000, Range:20000
SR Alg: metric based SPF
LSP ID : Dut-F.01-00
LSP ID : Dut-F.03-00
Level (1) Capability Count : 14
Displaying Level 2 capabilities
-------------------------------------------------------------------------------
LSP ID : Dut-A.00-00
Router Cap : 10.20.1.1, D:0, S:0
TE Node Cap : B E M P
SR Cap: IPv4 MPLS-IPv6
SRGB Base:20000, Range:20000
SR Alg: metric based SPF
LSP ID : Dut-A.02-00
LSP ID : Dut-A.03-00
LSP ID : Dut-B.00-00
Router Cap : 10.20.1.2, D:0, S:0
TE Node Cap : B E M P
SR Cap: IPv4 MPLS-IPv6
SRGB Base:20000, Range:20000
SR Alg: metric based SPF
LSP ID : Dut-C.00-00
Router Cap : 10.20.1.3, D:0, S:0
TE Node Cap : B E M P
SR Cap: IPv4 MPLS-IPv6
SRGB Base:20000, Range:20000
SR Alg: metric based SPF
LSP ID : Dut-C.02-00
LSP ID : Dut-D.00-00
Router Cap : 10.20.1.4, D:0, S:0
TE Node Cap : B E M P
SR Cap: IPv4 MPLS-IPv6
SRGB Base:20000, Range:20000
SR Alg: metric based SPF
LSP ID : Dut-D.01-00
LSP ID : Dut-E.00-00
Router Cap : 10.20.1.5, D:0, S:0
TE Node Cap : B E M P
SR Cap: IPv4 MPLS-IPv6
SRGB Base:20000, Range:20000
SR Alg: metric based SPF
LSP ID : Dut-E.01-00
LSP ID : Dut-E.02-00
LSP ID : Dut-F.00-00
Router Cap : 10.20.1.6, D:0, S:0
TE Node Cap : B E M P
SR Cap: IPv4 MPLS-IPv6
SRGB Base:20000, Range:20000
SR Alg: metric based SPF
LSP ID : Dut-F.01-00
LSP ID : Dut-F.03-00
Level (2) Capability Count : 14
===============================================================================
*A:ALA-A#
Label |
Description |
|---|---|
LSP ID |
Displays the LSP ID of the specified system ID or hostname |
Router Cap |
Displays the router IP address and capability |
TE Node Cap |
Displays the TE node capability |
SR Cap |
Displays the segment routing capability |
SRGB Base |
Displays the Segment Routing Global Block (SRGB) base index value and range |
SR Alg |
Displays the type of SR algorithm used for the specified LSP ID |
Level (n) Capability Count |
Displays the capability count for the specified level |
database [system-id | lsp-id] [detail] [level level]
show>router>isis
Supported on all 7210 SAS platforms as described in this document
This command displays the entries in the IS-IS link state database. If no parameters are specified, all entries are displayed.
Displays only the LSPs related to the specified system-id. If no system-id or lsp-id is specified, all database entries are listed.
Displays only the specified LSP (hostname). If no system-id or lsp-id is specified, all database entries are listed.
Keyword to specify that all output is displayed in the detailed format.
Displays only the specified IS-IS protocol level attributes.
The following output is an example of IS-IS database information, and Table: Output fields: router IS-IS database describes the output fields.
Sample output*A:ALA-A# show router isis database
===============================================================================
Router Base ISIS Instance 1 Database
===============================================================================
LSP ID Sequence Checksum Lifetime Attributes
-------------------------------------------------------------------------------
Displaying Level 1 database
-------------------------------------------------------------------------------
abr_dfw.00-00 0x50 0x164f 603 L1L2
Level (1) LSP Count : 1
Displaying Level 2 database
-------------------------------------------------------------------------------
asbr_east.00-00 0x53 0xe3f5 753 L1L2
abr_dfw.00-00 0x57 0x94ff 978 L1L2
abr_dfw.03-00 0x50 0x14f1 614 L1L2
Level (2) LSP Count : 3
===============================================================================
*A:ALA-A#
*A:Dut-B# show router isis database Dut-A.00-00 detail
==============================================================================
Router Base ISIS Instance 1 Database
==============================================================================
Displaying Level 1 database
------------------------------------------------------------------------------
Level (1) LSP Count : 0
Displaying Level 2 database
------------------------------------------------------------------------------
LSP ID : Dut-A.00-00 Level : L2
Sequence : 0x6 Checksum : 0xb7c4 Lifetime : 1153
Version : 1 Pkt Type : 20 Pkt Ver : 1
Attributes: L1L2 Max Area : 3
SysID Len : 6 Used Len : 311 Alloc Len : 311
TLVs :
Area Addresses:
Area Address : (2) 30.31
Supp Protocols:
Protocols : IPv4
IS-Hostname : Dut-A
Router ID :
Router ID : 10.20.1.1
I/F Addresses :
I/F Address : 10.20.1.1
I/F Address : 10.10.1.1
I/F Address : 10.10.2.1
TE IS Nbrs :
Nbr : Dut-B.01
Default Metric : 1000
Sub TLV Len : 98
IF Addr : 10.10.1.1
MaxLink BW: 100000 kbps
Resvble BW: 100000 kbps
Unresvd BW:
BW[0] : 10000 kbps
BW[1] : 40000 kbps
BW[2] : 40000 kbps
BW[3] : 40000 kbps
BW[4] : 50000 kbps
BW[5] : 50000 kbps
BW[6] : 50000 kbps
BW[7] : 10000 kbps
Admin Grp : 0x0
TE Metric : 1000
SUBTLV BW CONSTS : 8
BW Model : 1
BC[0]: 10000 kbps
BC[1]: 0 kbps
BC[2]: 40000 kbps
BC[3]: 0 kbps
BC[4]: 0 kbps
BC[5]: 50000 kbps
BC[6]: 0 kbps
BC[7]: 0 kbps
TE IP Reach :
Default Metric : 0
Control Info: , prefLen 32
Prefix : 10.20.1.1
Default Metric : 1000
Control Info: , prefLen 24
Prefix : 10.10.1.0
Default Metric : 1000
Control Info: , prefLen 24
Prefix : 10.10.2.0
Level (2) LSP Count : 1
==============================================================================
*A:Dut-B#
Label |
Description |
|---|---|
LSP ID |
Displays the LSP ID LSP IDs are auto-assigned by the originating IS-IS node. The LSP ID is comprised of three sections. The first 6 bytes is the system ID for that node, followed by a single byte value for the pseudonode generated by that router, and a fragment byte which starts at zero. For example, if a router system ID is 1800.0000.0029, the first LSP ID is 1800.0000.0029.00-00. If there are too many routes, LSP ID 1800.0000.0029.00-01 is created to contain the excess routes. If the router is the Designated Intermediate System (DIS) on a broadcast network, a pseudo-node LSP is created. Usually the internal circuit ID is used to determine the ID assigned to the pseudonode. For instance, for circuit 4, an LSP pseudonode with ID 1800.0000.0029.04-00 is created. The router learns hostnames and uses the hostname in place of the system ID. An example of LDP IDs are: acc_arl.00-00 acc_arl.00-01 acc_arl.04-00 |
Sequence |
Displays the sequence number of the LSP that allows other systems to determine whether they have received the latest information from the source |
Checksum |
Displays the checksum of the entire LSP packet |
Lifetime |
Displays the amount of time, in seconds, that the LSP remains valid. |
Attributes |
OV — The overload bit is set L1 — Specifies a Level 1 IS type L2 — Specifies a Level 2 IS type ATT — The attach bit is set. When this bit is set, the router can also act as a Level 2 router and can reach other areas |
LSP Count |
Displays the sum of all the configured Level 1 and Level 2 LSPs. |
LSP ID |
Displays a unique identifier for each LSP composed of SysID, Pseudonode ID, and LSP name |
Lifetime |
Displays the remaining time until the LSP expires |
Version |
Displays the version/protocol ID extension. This value is always set to 1. |
Pkt Type |
Displays the PDU type number |
Pkt Ver |
Displays the version/protocol ID extension. This value is always set to 1. |
Max Area |
Displays the maximum number of area addresses supported |
Sys ID Len |
Displays the length of the system ID field (0 or 6 for 6 digits) |
Use Len |
Displays the actual length of the PDU |
Alloc Len |
Displays the amount of memory space allocated for the LSP |
Area Address |
Displays the area addresses to which the router is connected |
Supp Protocols |
Displays the data protocols that are supported |
IS-Hostname |
Displays the name of the router originating the LSP |
Virtual Flag |
0 — Level 1 intermediate systems report this octet as 0 to all neighbors 1 — Indicates that the path to a neighbor is a Level 2 virtual path used to repair an area partition |
Neighbor |
Displays the routers running interfaces to which the router is connected |
Internal Reach |
Displays a 32-bit metric. A bit is added for the ups and downs resulting from Level 2 to Level 1 route-leaking. |
IP Prefix |
Displays the IP addresses that the router knows about by externally-originated interfaces |
Metrics |
Displays a routing metric used in the IS-IS link-state calculation |
hostname
show>router>isis
Supported on all 7210 SAS platforms as described in this document
This command displays the hostname database. There are no options or parameters.
The following output is an example of IS-IS hostname database information, and Table: Output fields: router IS-IS hostname describes the output fields.
Sample outputA:ALA-A# show router isis hostname
=========================================================================
Router Base ISIS Instance 1 Hostnames
=========================================================================
System Id Hostname
-------------------------------------------------------------------------
1800.0000.0002 core_west
1800.0000.0005 core_east
1800.0000.0008 asbr_west
1800.0000.0009 asbr_east
1800.0000.0010 abr_sjc
1800.0000.0011 abr_lax
1800.0000.0012 abr_nyc
1800.0000.0013 abr_dfw
1800.0000.0015 dist_oak
1800.0000.0018 dist_nj
1800.0000.0020 acc_nj
1800.0000.0021 acc_ri
1800.0000.0027 dist_arl
1800.0000.0028 dist_msq
1800.0000.0029 acc_arl
1800.0000.0030 acc_msq
=========================================================================
A:ALA-A#
Label |
Description |
|---|---|
System-id |
Displays the system identifier mapped to hostname |
Hostname |
Displays the hostname for the specific system-id |
Type |
Displays the type of entry (static or dynamic) |
interface [ip-int-name | ip-address] [detail]
show>router>isis
Supported on all 7210 SAS platforms as described in this document
This command shows IS-IS interface information.
If no parameters are specified, all entries are displayed.
Specifies the IP interface name. An interface name cannot be in the form of an IP address. Interface names can be any string up to 32 character composed of printable, 7-bit ASCII characters. If the string contains special characters (such as #, $, and spaces), the entire string must be enclosed within double quotes.
Specifies the interface IP address.
Displays only the adjacency with the specified system ID.
Displays detailed information about the adjacency.
The following output is an example of IS-IS interface information, and Table: Output fields: IS-IS interface describes the output fields.
Sample outputA:ALA-A# show router isis interface
===============================================================================
ISIS Interfaces
===============================================================================
Interface Level CircID Oper State L1/L2 Metric
-------------------------------------------------------------------------------
system L1L2 1 Up 10/10
if2/1 L2 8 Up -/10
if2/2 L1 5 Up 10/-
if2/3 L1 6 Up 10/-
if2/4 L1 7 Up 10/-
if2/5 L2 2 Up -/10
lag-1 L2 3 Up -/10
if2/8 L2 4 Up -/10
-------------------------------------------------------------------------------
Interfaces : 8
===============================================================================
A:ALA-A#
Router Base ISIS Instance 1 Interfaces
Router Base ISIS Instance 1 Interfaces
*A:JC-NodeA# show router isis interface detail
===============================================================================
Router Base ISIS Instance 1 Interfaces
===============================================================================
Interface : ip-10.10.1.1 Level Capability: L1L2
Oper State : Up Admin State : Up
Auth Type : None
Circuit Id : 2 Retransmit Int. : 5
Type : Broadcast LSP Pacing Int. : 100
Mesh Group : Inactive CSNP Int. : 10
Bfd Enabled : No
Level : 1 Adjacencies : 0
Desg. IS : JC-NodeA
Auth Type : None Metric : 10
Hello Timer : 9 Hello Mult. : 3
Priority : 64
Passive : No Te-Metric : 2
Level : 2 Adjacencies : 0
Desg. IS : JC-NodeA
Auth Type : None Metric : 10
Hello Timer : 9 Hello Mult. : 3
Priority : 64 : 10
Passive : No Te-Metric : 21
===============================================================================
*A:JC-NodeA#
Label |
Description |
|---|---|
Interface |
Displays the interface name |
Level |
Displays the interface level (1, 2, or 1 and 2) |
CirID |
Displays the circuit identifier |
Oper State |
Up — The interface is operationally up |
Down — The interface is operationally down |
|
L1/L2 Metric |
Displays the interface metric for Level 1 and Level 2, if none are set to 0 |
lfa-coverage
show>router>isis
Supported on all 7210 SAS platforms as described in this document
This command shows IS-IS LFA coverage information.
The following output is an example of IS-IS LFA coverage information, and Table: Output fields: LFA coverage describes the output fields.
Sample outputA:ALA-A# show router isis lfa-coverage
Rtr Base ISIS Instance 0 LFA Coverage
============================================================================
Topology Level Node IPv4
----------------------------------------------------------------------------
IPV4 Unicast L1 4/4(100%) 826/826(100%)
IPV4 Unicast L2 2/2(100%) 826/826(100%)
IPV6 Unicast L1 3/3(100%) 0/0(0%)
IPV6 Unicast L2 0/0(0%) 0/0(0%)
============================================================================
A:ALA-A#
Label |
Description |
|---|---|
Topology |
Displays the type of network |
Level |
Displays the IS-IS level in which LFA is enabled |
Node |
Displays the number of nodes in the level on which LFA is enabled |
IPv4 |
Displays the number of IPv4 interfaces on the nodes on which LFA is enabled |
link-group-member-status name [level level]
show>router>isis
Supported on all 7210 SAS platforms as described in this document
This command displays IS-IS link group member status information.
Specifies the link group member name, up to 32 characters.
Specifies the interface level.
The following output is an example of IS-IS link group member status information, and Table: Output fields: link group member status describes the output fields.
Sample outputA:ALA-A# show router isis link-group-member-status
===============================================================================
Rtr Base ISIS Instance 0 Link-Group Member
===============================================================================
Link-group I/F name Level State
-------------------------------------------------------------------------------
toDutB ip-10.10.12.3 L1 Up
toDutB ip-10.10.3.3 L1 Up
toDutB ip-10.10.12.3 L2 Up
toDutB ip-10.10.3.3 L2 Up
-------------------------------------------------------------------------------
Legend: BER = bitErrorRate
===============================================================================
A:ALA-A#
Label |
Description |
|---|---|
Link-group |
Displays the link group |
I/F name |
Displays the interface name |
Level |
Displays the interface level (1, 2, or 1 and 2) |
State |
Up — The interface is operationally up Down — The interface is operationally down |
link-group-status name [level level]
show>router>isis
Supported on all 7210 SAS platforms as described in this document
This command displays IS-IS Link Group status information.
Specifies the link group name, up to 32 characters.
Specifies the interface level.
The following output is an example of IS-IS link group status information.
Sample outputA:ALA-A# show router isis link-group-status
===============================================================================
Rtr Base ISIS Instance 0 Link-Group Status
===============================================================================
Link-group Mbrs Oper Revert Active Level State
Mbr Mbr Mbr
-------------------------------------------------------------------------------
toDutB 2 2 2 2 L1 normal
toDutB 2 2 2 2 L2 normal
toDutE 2 2 2 2 L1 normal
toDutE 2 2 2 2 L2 normal
===============================================================================
A:ALA-A#
prefix-sids [ipv4-unicast] [ip-prefix[/prefix-length]] [sid sid] [adv-router system-id | hostname]
show>router>isis
Supported on all 7210 SAS platforms as described in this document
This command displays IS-IS prefix SIDs.
Displays information about the IPv4 unicast prefix SIDs.
Displays the IP prefix and mask length.
Displays information related to the specified segment routing ID.
Displays only the prefix SIDs related to the specified system ID or host name, up to 38 characters.
The following output is an example of IS-IS prefix SID information, and Table: Output fields: prefix SIDs describes the output fields.
Sample output*A:Dut-C# show router isis prefix-sids
===============================================================================
Rtr Base ISIS Instance 0 Prefix/SID Table
===============================================================================
Prefix SID Lvl/Typ SRMS AdvRtr
MT Flags
-------------------------------------------------------------------------------
10.0.0.1/32 1 2/Int. N Dut-B
0 RNnP
10.0.0.1/32 1 2/Int. N Dut-C
0 RNnP
10.0.0.1/32 1 1/Int. N Dut-D
0 NnP
10.0.0.1/32 1 2/Int. N Dut-D
0 NnP
10.0.0.1/32 1 2/Int. N Dut-E
0 RNnP
10.20.1.2/32 1002 1/Int. N Dut-B
0 NnP
10.20.1.2/32 1002 2/Int. N Dut-B
0 NnP
10.20.1.2/32 1002 2/Int. N Dut-C
0 RNnP
10.20.1.2/32 1002 2/Int. N Dut-D
0 RNnP
10.20.1.2/32 1002 2/Int. N Dut-E
0 RNnP
10.20.1.3/32 1003 2/Int. N Dut-B
0 RNnP
10.20.1.3/32 1003 1/Int. N Dut-C
0 NnP
10.20.1.3/32 1003 2/Int. N Dut-C
0 NnP
10.20.1.3/32 1003 2/Int. N Dut-D
0 RNnP
10.20.1.3/32 1003 2/Int. N Dut-E
0 RNnP
10.20.1.4/32 1004 2/Int. N Dut-B
0 RNnP
10.20.1.4/32 1004 2/Int. N Dut-C
0 RNnP
10.20.1.4/32 1004 1/Int. N Dut-D
0 NnP
10.20.1.4/32 1004 2/Int. N Dut-D
0 NnP
10.20.1.4/32 1004 2/Int. N Dut-E
0 RNnP
10.20.1.5/32 1005 2/Int. N Dut-B
0 RNnP
10.20.1.5/32 1005 2/Int. N Dut-C
0 RNnP
10.20.1.5/32 1005 2/Int. N Dut-D
0 RNnP
10.20.1.5/32 1005 1/Int. N Dut-E
0 NnP
10.20.1.5/32 1005 2/Int. N Dut-E
0 NnP
-------------------------------------------------------------------------------
No. of Prefix/SIDs: 25
Flags: R = Re-advertisement
N = Node-SID
nP = no penultimate hop POP
E = Explicit-Null
V = Prefix-SID carries a value
L = value/index has local significance
===============================================================================
*A:Dut-C#
Label |
Description |
|---|---|
Prefix |
Displays the IP prefix for the SID |
SID |
Displays the segment routing identifier (SID) |
Lvl/Typ |
Displays the level and type of SR |
SRMS |
Displays whether the prefix SID is advertised by the SR mapping service: Y (yes) or N (no) |
MT |
Displays the multicast tunnel number (0, 2, 3, or 4) |
AdvRtr |
Displays the advertised router name |
Flags |
Displays the flags related to the advertised router: R = re-advertisement N = node-SID nP = no penultimate hop POP E = explicit-null V = prefix-SID carries a value L = value/index has local significance |
routes [ipv4-unicast | ipv6-unicast | mt mt-id-number] [ip-prefix/prefix-length] [alternative]
show>router>isis
Supported on all 7210 SAS platforms as described in this document
This command displays the routes in the IS-IS route table.
Displays IPv4 unicast parameters.
Displays IPv6 unicast parameters.
Displays unicast multi-topology information.
Displays information for the specified IP address.
Displays the level of protection per prefix.
The following output is an example of IS-IS route information, and Table: Output fields: IS-IS routes describes the output fields.
Sample output*A:Dut-A# show router isis routes
===============================================================================
Router Base ISIS Instance 1 Route Table
===============================================================================
Prefix Metric Lvl/Typ Ver. SysID/Hostname
NextHop MT
-------------------------------------------------------------------------------
10.10.1.0/24 10 1/Int. 5 Dut-A
0.0.0.0 0
10.10.3.0/24 20 1/Int. 137 Dut-B
10.10.1.2 0
10.10.4.0/24 20 1/Int. 137 Dut-B
10.10.1.2 0
10.10.5.0/24 30 1/Int. 137 Dut-B
10.10.1.2 0
10.10.9.0/24 60 1/Int. 52 Dut-F
10.10.21.6 0
10.10.10.0/24 70 1/Int. 52 Dut-F
10.10.21.6 0
10.10.12.0/24 20 1/Int. 137 Dut-B
10.10.1.2 0
10.10.13.0/24 10 1/Int. 7 Dut-A
0.0.0.0 0
10.10.14.0/24 20 1/Int. 52 Dut-F
10.10.21.6 0
10.10.15.0/24 30 1/Int. 137 Dut-B
10.10.1.2 0
10.10.16.0/24 30 1/Int. 137 Dut-B
10.10.1.2 0
10.10.21.0/24 10 1/Int. 48 Dut-A
0.0.0.0 0
10.10.22.0/24 30 1/Int. 137 Dut-B
10.10.1.2 0
10.20.1.1/32 0 1/Int. 10 Dut-A
0.0.0.0 0
10.20.1.2/32 10 1/Int. 137 Dut-B
10.10.1.2 0
10.20.1.3/32 20 1/Int. 137 Dut-B
10.10.1.2 0
10.20.1.4/32 20 1/Int. 137 Dut-B
10.10.1.2 0
10.20.1.5/32 30 1/Int. 137 Dut-B
10.10.1.2 0
10.20.1.6/32 10 1/Int. 52 Dut-F
10.10.21.6 0
10.10.1.0/24 10 1/Int. 65 Dut-A
0.0.0.0 2
10.10.13.0/24 10 1/Int. 65 Dut-A
0.0.0.0 2
10.10.21.0/24 10 1/Int. 65 Dut-A
0.0.0.0 2
10.20.1.1/32 0 1/Int. 65 Dut-A
0.0.0.0 2
-------------------------------------------------------------------------------
No. of Routes: 20
===============================================================================
*A:Dut-A#
Label |
Description |
|---|---|
Prefix |
Displays the route prefix and mask |
Metric MT |
Displays the route metric. |
Lvl/Type |
Displays the level (1 or 2) and the route type, Internal (Int) or External (Ext) |
Version |
Displays the SPF version that generated the route |
Nexthop |
Displays the system ID of next hop |
Hostname |
Displays the hostname for the specific system-id |
spf-log [detail]
show>router>isis
Supported on all 7210 SAS platforms as described in this document
This command displays the last 20 IS-IS SFP events.
The following output is an example of IS-IS SPF log information, and Table: Output fields: IS-IS SPF log describes the output fields.
Sample outputA:ALA-48# show router isis spf-log
===============================================================================
Router Base ISIS Instance 1 SPF Log
===============================================================================
When Duration L1 Nodes L2 Nodes Event Count Type
-------------------------------------------------------------------------------
01/30/2007 11:01:54 <0.01s 1 1 3
-------------------------------------------------------------------------------
Log Entries : 1
===============================================================================
A:ALA-48#
Label |
Description |
|---|---|
When |
Displays the timestamp when the SPF run started on the system |
Duration |
Displays the time (in hundredths of a second) required to complete the SPF run |
L1 Nodes |
Displays the number of Level 1 nodes involved in the SPF run |
L2 Nodes |
Displays the number of Level 2 nodes involved in the SPF run |
Event Count |
Displays the number of SPF events that triggered the SPF calculation |
Log Entries |
Displays the total number of log entries |
statistics
show>router>isis
Supported on all 7210 SAS platforms as described in this document
This command displays information about IS-IS traffic statistics.
The following output is an example of IS-IS traffic statistics information, and Table: Output fields: IS-IS statistics describes the output fields.
Sample outputA:dut-b>show>router>isis# statistics
===============================================================================
Router Base ISIS Instance 0 Statistics
===============================================================================
ISIS Instance : 0 SPF Runs : 2
Purge Initiated : 0 LSP Regens. : 36
CSPF Statistics
Requests : 0 Request Drops : 0
Paths Found : 0 Paths Not Found: 0
LFA Statistics
LFA Runs : 1
-------------------------------------------------------------------------------
PDU Type Received Processed Dropped Sent Retransmitted
-------------------------------------------------------------------------------
LSP 0 0 0 0 0
IIH 0 0 0 0 0
CSNP 0 0 0 0 0
PSNP 0 0 0 0 0
Unknown 0 0 0 0 0
===============================================================================
A:dut-b>show>router>isis#
Label |
Description |
|---|---|
Purge Initiated |
Displays the number of times purges have been initiated |
SPF Runs |
Displays the number of times shortest path first calculations have been made |
LSP Regens |
Displays the count of LSP regenerations |
Requests |
Displays the number of CSPF requests made to the protocol |
Paths Found |
Displays the number of responses to CSPF requests for which paths satisfying the constraints were found |
PDU Type |
Displays the PDU type |
Received |
Displays the count of link state PDUs received by this instance of the protocol |
Processed |
Displays the count of link state PDUs processed by this instance of the protocol |
Dropped |
Displays the count of link state PDUs dropped by this instance of the protocol |
Sent |
Displays the count of link state PDUs sent out by this instance of the protocol |
Retransmitted |
Displays the count of link state PDUs that were retransmitted by this instance of the protocol |
LFA Runs |
Displays the number of time the shortest path first algorithm has been run to calculate the LFA (backup path to a destination). |
status
show>router>isis
Supported on all 7210 SAS platforms as described in this document
This command displays information about IS-IS status.
The following output is an example of IS-IS status information, and Table: Output fields: IS-IS status describes the output fields.
Sample output
*A:ALU_SIM11>show>router>isis# status
===============================================================================
Router Base ISIS Instance 1 Status
===============================================================================
System Id : 0010.0100.1002
Admin State : Up
Ipv4 Routing : Enabled
Last Enabled : 07/06/2010 12:28:12
Level Capability : L1L2
Authentication Check : True
Authentication Type : None
CSNP-Authentication : Enabled
HELLO-Authentication : Enabled
PSNP-Authentication : Enabled
Traffic Engineering : Disabled
Graceful Restart : Disabled
GR Helper Mode : Disabled
LSP Lifetime : 1200
LSP Wait : 5 sec (Max) 0 sec (Initial) 1 sec (Second)
Adjacency Check : loose
L1 Auth Type : none
L2 Auth Type : none
L1 CSNP-Authenticati*: Enabled
L1 HELLO-Authenticat*: Enabled
L1 PSNP-Authenticati*: Enabled
L1 Preference : 15
L2 Preference : 18
L1 Ext. Preference : 160
L2 Ext. Preference : 165
L1 Wide Metrics : Disabled
L2 Wide Metrics : Disabled
L1 LSDB Overload : Disabled
L2 LSDB Overload : Disabled
L1 LSPs : 3
L2 LSPs : 3
Last SPF : 07/06/2010 12:28:17
SPF Wait : 10 sec (Max) 1000 ms (Initial) 1000 ms (Second)
Export Policies : None
Multicast Import : None
Multi-topology : Disabled
Advertise-Passive-On*: Disabled
Suppress Default : Disabled
Default Route Tag : None
Area Addresses : 01
Ldp Sync Admin State : Up
LDP-over-RSVP : Disabled
Loopfree-Alternate : Enabled
L1 LFA : Included
L2 LFA : Included
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:ALU_SIM11>show>router>isis#
Label |
Description |
|---|---|
System-id |
Displays the neighbor system ID |
Admin State |
Up — IS-IS is administratively up Down — IS-IS is administratively down |
Ipv4 Routing |
Enabled — IPv4 routing is enabled Disabled — IPv4 routing is disabled |
Ipv6 Routing |
Disabled — IPv6 routing is disabled Enabled, Native — IPv6 routing is enabled Enabled, Multi-topology — Multi-topology TLVs for IPv6 routing is enabled |
Multi-topology |
Disabled — Multi-topology TLVs for IPv6 routing is disabled Enabled — Multi-topology TLVs for IPv6 routing is enabled |
Last Enabled |
Displays the date/time when IS-IS was last enabled in the router |
Level Capability |
Displays the routing level for the IS-IS routing process |
Authentication Check |
True — All IS-IS mismatched protocol packets are rejected False — Authentication is performed on received IS-IS protocol packets but mismatched packets are not rejected |
Authentication Type |
Displays the method of authentication used to verify the authenticity of packets sent by neighboring routers on an IS-IS interface. |
Traffic Engineering |
Enabled — TE is enabled for the router Disabled — TE is disabled so that TE metrics are not generated and are ignored when received by this node |
Graceful Restart |
Enabled — Graceful restart is enabled for this instance of IS-IS on the router Disabled — Graceful restart capability is disabled for this instance of IS-IS on the router |
Ldp Sync Admin State |
Displays whether the IGP-LDP synchronization feature is enabled or disabled on all interfaces participating in the IS-IS routing protocol |
Loopfree-Alternate |
Displays the interface LFA status (included in LFA computation or excluded in LFA computations) |
L1 LFA |
Displays the LFA status for an IS-IS Level 1 (included in LFA computation or excluded in LFA computations) |
L2 LFA |
Displays the LFA status for an IS-IS Level 2 (included in LFA computation or excluded in LFA computations) |
summary-address [ip-prefix[/prefix-length]]
show>router>isis
Supported on all 7210 SAS platforms as described in this document
This command displays IS-IS summary address information.
Displays information for the specified IP address.
The following output is an example of IS-IS summary address information, and Table: Output fields: IS-IS summary address describes the output fields.
Sample outputA:ALA-48# show router isis summary-address
===============================================================================
Router Base ISIS Instance 1 Summary Address
===============================================================================
Address Level
-------------------------------------------------------------------------------
10.0.0.0/8 L1
10.1.0.0/24 L1L2
10.1.2.3/32 L2
-------------------------------------------------------------------------------
Summary Addresses : 3
===============================================================================
A:ALA-48#
Label |
Description |
|---|---|
Address |
Displays the IP address |
Level |
Displays the IS-IS level from which the prefix should be summarized |
topology [[ipv4-unicast | ipv6-unicast | mt mt-id-number][detail]]
show>router>isis
Supported on all 7210 SAS platforms as described in this document
This command displays IS-IS unicast topology information.
Displays IPv4 unicast parameters.
Displays IPv6 unicast parameters.
Displays unicast topology parameters.
Displays detailed unicast topology information.
The following output is an example of IS-IS unicast topology information, and Table: Output fields: IS-IS topology describes the output fields.
Sample output*A:duth# show router isis 1 topology
===============================================================================
Router Base ISIS Instance 1 Topology Table
===============================================================================
Node Interface Nexthop
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
IS-IS IP paths (MT-ID 0), Level 1
-------------------------------------------------------------------------------
dutb.00 toB dutb
dutg.00 toG dutg
duti.00 toB dutb
duti.01 toB dutb
duti.02 toG dutg
-------------------------------------------------------------------------------
IS-IS IP paths (MT-ID 0), Level 2
-------------------------------------------------------------------------------
dutb.00 toB dutb
dutg.00 toG dutg
duti.00 toB dutb
duti.01 toB dutb
duti.02 toG dutg
===============================================================================
Label |
Description |
|---|---|
Node |
Displays the IP address |
Interface |
Displays the interface name |
Nexthop |
Displays the next-hop IP address |