group [grp-ip-address]
group summary
show>router>igmp
Supported on all 7210 SAS platforms as described in this document, except those operating in access-uplink mode
This command displays the multicast group and (S,G) addresses. If no grp-ip-address parameters are specified, all IGMP group, (*,G), and (S,G) addresses are displayed.
Displays specific multicast group addresses.
The following output is an example of IGMP multicast group information, and Table: Output fields: IGMP group describes the output fields.
Sample output*B:Dut-C# show router igmp group
===============================================================================
IGMP Interface Groups
===============================================================================
===============================================================================
IGMP Host Groups
===============================================================================
(*,224.0.0.1)
Fwd List : 239.112.1.2 Up Time : 0d 00:00:21
(10.11.0.1,224.0.0.1)
Fwd List : 239.112.1.1 Up Time : 0d 00:00:30
Blk List : 239.112.1.2 Up Time : 0d 00:00:21
(10.11.0.2,224.0.0.1)
Fwd List : 239.112.1.1 Up Time : 0d 00:00:30
(*,224.0.0.2)
Fwd List : 239.112.1.2 Up Time : 0d 00:00:21
(10.11.0.1,224.0.0.2)
Blk List : 239.112.1.2 Up Time : 0d 00:00:21
-------------------------------------------------------------------------------
(*,G)/(S,G) Entries : 5
===============================================================================
*B:Dut-C#
*B:Dut-C# show router igmp group summary
===============================================================================
IGMP Interface Groups
===============================================================================
===============================================================================
IGMP Host Groups Summary Nbr Fwd Nbr Blk
===============================================================================
(*,224.0.0.1) 1 0
(10.11.0.1,224.0.0.1) 1 1
(10.11.0.2,224.0.0.1) 1 0
(*,224.0.0.2) 1 0
(10.11.0.1,225.0.0.2) 0 1
-------------------------------------------------------------------------------
(*,G)/(S,G) Entries : 5
===============================================================================
*B:Dut-C#
A:NYC# show router igmp group 224.24.24.24
===============================================================================
IGMP Groups
===============================================================================
(*,239.24.24.24) Up Time : 0d 05:23:23
Fwd List : nyc-vlc
-------------------------------------------------------------------------------
(*,G)/(S,G) Entries : 1
===============================================================================
A:NYC#
Label |
Description |
|---|---|
IGMP Groups |
Displays the IP multicast sources corresponding to the IP multicast groups that4 are statically configured |
Fwd List |
Displays the list of interfaces in the forward list |
Blk List |
Displays the list of interfaces in the blocked list |
ssm-translate
ssm-translate interface interface-name
show>router>igmp
Supported on all 7210 SAS platforms as described in this document
This command displays IGMP SSM translate configuration information.
The following output is an example of IGMP SSM translate information, and Table: Output fields: IGMP SSM-translate describes the output fields.
Sample output=================================================================
IGMP SSM Translate Entries
=================================================================
Group Range Source Interface
-----------------------------------------------------------------
<239.1.1.1 - 239.1.1.2> 10.1.1.1
<239.1.1.1 - 239.1.1.5> 10.1.1.2 ies-abc
-----------------------------------------------------------------
Label |
Description |
|---|---|
Group Range |
Displays the address ranges of the multicast groups for which this router can be an RP |
Source |
Displays the unicast address that sends data on an interface |
SSM Translate Entries |
Displays the total number of SSM translate entries |
interface [ip-int-name | ip-address] [group] [grp-address] [detail]
show>router>igmp
Supported on all 7210 SAS platforms as described in this document
This command displays IGMP interface information.
Displays the information associated with only the specified IP interface name.
Displays the information associated with only the specified IP address.
Displays only the IP multicast group address for which this entry contains information.
Displays detailed IP interface information along with the source group information learned on that interface.
The following output is an example of IGMP interface information, and Table: Output fields: IGMP interface describes the fields.
Sample outputshow router igmp interface output
*A:ALA-BA# show router 100 igmp interface
===============================================================================
IGMP Interfaces
===============================================================================
Interface Adm Oper Querier Cfg/Opr Num Policy
Version Groups
-------------------------------------------------------------------------------
IGMP_to_CE Up Up 10.1.1.1 1/1 3 none
-------------------------------------------------------------------------------
Interfaces : 1
===============================================================================
*A:ALA-BA#
*A:7210SAS>show>router# interface
===============================================================================
Interface Table (Router: Base)
===============================================================================
Interface-Name Adm Opr(v4/v6) Mode Port/SapId
IP-Address PfxState
-------------------------------------------------------------------------------
system Up Up/Down Network system
10.3.3.3/32 n/a
toD_1 Up Up/Down Network 1/1/6
10.1.3.3/24 n/a
toE_1 Up Up/Down Network 1/1/5
10.1.2.3/24 n/a
toIxia_1 Up Up/Down IES 1/1/16:1
10.2.1.3/24 n/a
-------------------------------------------------------------------------------
Interfaces : 4
===============================================================================
*A:7210SAS>show>router#
Label |
Description |
|---|---|
Interface |
Specifies the interfaces that participate in the IGMP protocol |
Adm Admin Status |
Displays the administrative state for the IGMP protocol on this interface |
Oper Oper Status |
Displays the current operational state of IGMP protocol on the interface |
Querier |
Displays the address of the IGMP querier on the IP subnet to which the interface is attached |
Querier Up Time |
Displays the time since the querier was last elected as querier |
Querier Expiry Timer |
Displays the time remaining before the querier ages out. If the querier is the local interface address, the value is zero. |
Cfg/Opr Version Admin/Oper version |
Cfg — configured version of IGMP running on this interface. For IGMP to function correctly, all routers on a LAN must be configured to run the same version of IGMP on that LAN Opr — operational version of IGMP running on this interface. For example, if the cfg value is 3 but all the routers in the local subnet of this interface use IGMP version v1 or v2, the operational version is v1 or v2 |
Num Groups |
Displays the number of multicast groups that have been learned by the router on the interface |
Policy |
Displays the policy that is to be applied on the interface |
Group Address |
Displays the IP multicast group address for which this entry contains information |
Up Time |
Displays the time since this source group entry was created |
Last Reporter |
Displays the IP address of the source of the last membership report received for this IP multicast group address on this interface. If no membership report has been received, this object has the value 0.0.0.0. |
Mode |
The mode is based on the type of membership reports received on the interface for the group. In the ‟include” mode, reception of packets sent to the specified multicast address is requested only from those IP source addresses listed in the source-list parameter of the IGMP membership report. In ‟exclude” mode, reception of packets sent to the specific multicast address is requested from all IP source addresses except those listed in the source-list parameter. |
V1 Host Timer |
Displays the time remaining until the local router assumes there are no longer any IGMP version 1 members on the IP subnet attached to this interface. Upon hearing an IGMPv1 Membership Report, this value is reset to the group membership timer. While this time remaining is non-zero, the local router ignores an IGMPv2 Leave messages for this group that it receives on this interface. |
V2 Host Timer |
Displays the time remaining until the local router assumes there are no longer IGMP version 2 members on the IP subnet attached to this interface. Upon hearing an IGMPv2 Membership Report, this value is reset to the group membership timer. While this time remaining is non-zero, the local router ignores IGMPv3 Leave messages for this group that it receives on this interface. |
Type |
Indicates how this group entry was learned. If this group entry was learned by IGMP, it is set to ‟dynamic.” For statically configured groups, the value is set to ‟static.” |
Compat Mode |
Used for routers to be compatible with older version routers. IGMPv3 hosts MUST operate in version 1 and version 2 compatibility modes. IGMPv3 hosts MUST keep state per local interface about the compatibility mode of each attached network. A host compatibility mode is determined by the Host Compatibility Mode variable, which can be in one of the following states: IGMPv1, IGMPv2, or IGMPv3. This variable is kept per interface and is dependent on the version of General Queries heard on that interface as well as the Older Version Querier Present timers for the interface. |
static [ip-int-name | ip-addr]
show>router>igmp
Supported on all 7210 SAS platforms as described in this document
This command displays static IGMP, (*,G), and (S,G) information.
Displays the information associated with only the specified IP interface name.
Displays the information associated with only the specified IP address.
The following output is an example of static IGMP information, and Table: Output fields: IGMP static describes the fields.
Sample output*A:ALA-BA# show router 100 igmp static
==================================================================
IGMP Static Group Source
==================================================================
Source Group Interface
------------------------------------------------------------------
10.11.11.11 239.136.22.3 IGMP_to_CE
* 239.1.1.1 IGMP_to_CE
10.22.22.22 239.255.255.255 IGMP_to_CE
------------------------------------------------------------------
Static (*,G)/(S,G) Entries : 3
==================================================================
*A:ALA-BA#
Label |
Description |
|---|---|
Source |
Displays entries that represent a source address from which receivers are interested or not interested in receiving multicast traffic |
Group |
Displays the IP multicast group address for which this entry contains information |
Interface |
Displays the interface name |
statistics [ip-int-name | ip-address]
show>router>igmp
Supported on all 7210 SAS platforms as described in this document.
This command displays IGMP statistics information.
Displays the information associated with only the specified IP interface name.
Displays the information associated with only the specified IP address.
The following output is an example of IGMP statistics information, and Table: Output fields: IGMP statistics describes the output fields.
Sample output*A:dut-e>show>router# igmp statistics
==================================================
IGMP Interface Statistics
==================================================
Message Type Received Transmitted
--------------------------------------------------
Queries 0 57
Report V1 0 0
Report V2 0 0
Report V3 0 0
Leaves 0 0
--------------------------------------------------
Global General Statistics
--------------------------------------------------
Bad Length : 0
Bad Checksum : 0
Unknown Type : 0
Drops : 0
Rx Non Local : 0
Rx Wrong Version : 0
Policy Drops : 0
No Router Alert : 0
Rx Bad Encodings : 0
Local Scope Pkts : 0
Resvd Scope Pkts : 0
--------------------------------------------------
Global Source Group Statistics
--------------------------------------------------
(S,G) : 0
(*,G) : 75
==================================================
*A:dut-e>show>router#
Label |
Description |
|---|---|
IGMP Interface Statistics |
Displays the IGMP statistics for a particular interface |
Message Type |
Queries — number of IGMP general queries transmitted or received on this interface Report — total number of IGMP V1, V2, or V3 reports transmitted or received on this interface Leaves — total number of IGMP leaves transmitted on this interface |
Received |
Displays the total number of IGMP packets received on this interface |
Transmitted |
Displays the total number of IGMP packets transmitted from this interface |
General Interface Statistics |
Displays the general IGMP statistics |
Bad Length |
Displays the total number of IGMP packets with bad length received on this interface |
Bad Checksum |
Displays the total number of IGMP packets with bad checksum received on this interface. |
Unknown Type |
Displays the total number of IGMP packets with unknown type received on this interface |
Bad Receive If |
Displays the total number of IGMP packets incorrectly received on this interface |
Rx Non Local |
Displays the total number of IGMP packets received from a non-local sender |
Rx Wrong Version |
Displays the total number of IGMP packets with wrong versions received on this interface |
Policy Drops |
Displays the total number of times IGMP protocol instance matched the host IP address or group/source addresses specified in the import policy |
No Router Alert |
Displays the total number of IGMPv3 packets received on this interface that do not have the router alert flag set |
status
show>router>igmp
Supported on all 7210 SAS platforms as described in this document.
This command displays IGMP status information.
If IGMP is not enabled, the following message appears:
A:NYC# show router igmp status
MINOR: CLI IGMP is not configured.
A:NYC#
The following output is an example of IGMP status information, and Table: Output fields: IGMP status describes the output fields.
Sample output*A:ALA-BA# show>router# igmp status
===============================================================================
IGMP Status
===============================================================================
Admin State : Up
Oper State : Up
Query Interval : 125
Last Member Query Interval : 1
Query Response Interval : 10
Robust Count : 2
===============================================================================
*A:ALA-BA#
Label |
Description |
|---|---|
Admin State |
Displays the administrative status of IGMP |
Oper State |
Displays the current operating state of this IGMP protocol instance on this router |
Query Interval |
Displays the frequency at which IGMP query packets are transmitted |
Last Member Query Interval |
Displays the maximum response time inserted into group-specific queries sent in response to leave group messages, and is also the amount of time between group-specific query messages |
Query Response Interval |
Displays the maximum query response time advertised in IGMPv2 queries |
Robust Count |
Displays the number of times the router retries a query |