evpn-mpls
show>service
7210 SAS-Mxp and 7210 SAS-Sx/S 1/10GE (standalone)
This command displays the remote EVPN-MPLS tunnel endpoints in the system.
The following output is an example of EVPN MPLS tunnel endpoint information, and Table: Output fields: EVPN MPLS tunnel endpoints describes the output fields.
Sample output*A:Dut-B# show service evpn-mpls
============================================================
EVPN MPLS Tunnel Endpoints
============================================================
EvpnMplsTEP Address EVPN-MPLS Dest ES Dest
------------------------------------------------------------
10.20.1.3 1 0
10.20.1.4 1 0
10.20.1.5 1 0
------------------------------------------------------------
Number of EvpnMpls Tunnel Endpoints: 3
------------------------------------------------------------
============================================================
|
Label |
Description |
|---|---|
|
EvpnMplsTEP |
Displays the tunnel endpoint addresses |
|
EVPN-MPLS Dest |
Displays the number of EVPN-MPLS destinations |
|
ES Dest |
Displays the Ethernet segment destination |
bgp-evpn
show>service>id
7210 SAS-Mxp and 7210 SAS-Sx/S 1/10GE (standalone)
This command displays the bgp-evpn configured parameters for a specified service, including the administrative status of MPLS, the configuration for mac-advertisement and unknown-mac-route, as well as the mac-duplication parameters. The command shows the duplicate MAC addresses that mac-duplication has detected.
If the service is BGP-EVPN MPLS, this command also shows the parameters corresponding to EVPN-MPLS.
The following output is an example of BGP EVPN information for a specified service, and Table: Output fields: service ID BGP-EVPN describes the output fields.
Sample output*A:Dut-B# /show service id 1 bgp-evpn
===============================================================================
BGP EVPN Table
===============================================================================
MAC Advertisement : Enabled
CFM MAC Advertise : Disabled
MAC Dup Detn Moves : 5 MAC Dup Detn Window: 3
MAC Dup Detn Retry : 9 Number of Dup MACs : 0
EVI : 1
-------------------------------------------------------------------------------
Detected Duplicate MAC Addresses Time Detected
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
===============================================================================
===============================================================================
BGP EVPN MPLS Information
===============================================================================
Admin Status : Enabled
Force Vlan Fwding : Disabled Control Word : Disabled
Split Horizon Group: (Not Specified)
Ingress Rep BUM Lbl: Disabled Max Ecmp Routes : 0
Ingress Ucast Lbl : 131069 Ingress Mcast Lbl : 131069
===============================================================================
===============================================================================
BGP EVPN MPLS Auto Bind Tunnel Information
===============================================================================
Resolution : any
Filter Tunnel Types: (Not Specified)
===============================================================================
|
Label |
Description |
|---|---|
|
BGP EVPN Table |
|
|
MAC Advertisement |
Displays whether MAC advertisement is enabled or disabled |
|
CFM MAC Advertise |
Displays whether CFM MAC advertise is enabled or disabled |
|
MAC Dup Detn Moves |
Displays the number of moves that trigger MAC duplication detection |
|
MAC Dup Detn Window |
Displays the configured window size used for duplicate MAC detection |
|
MAC Dup Detn Retry |
Displays the retry timer value used for MAC duplication detection. |
|
Number of Dup MACs |
Displays the number of duplicate MAC addresses |
|
EVI |
Displays the EVPN instance ID |
|
BGP EVPN MPLS Information |
|
|
Admin Status |
Displays the administrative status of the EVPN MPLS |
|
Force Vlan Fwding |
Displays the status of force-vlan-forwarding |
|
Control Word |
Displays the status of control |
|
Split Horizon Group |
Displays the split-horizon group membership information |
|
Ingress Rep BUM Lbl |
Displays the label used for Ingress BUM replication |
|
Max Ecmp Routes |
Displays the maximum number of ECMP routes |
|
Ingress Ucast Lbl |
Displays the ingress unicast label |
|
Ingress Mcast Lbl |
Displays the ingress multicast label |
|
BGP EVPN MPLS Auto Bind Tunnel Information |
|
|
Resolution |
Displays the transport tunnel resolution filter used |
|
Filter Tunnel Types |
Displays auto-bind-tunnel resolution filter values, if applicable |
evpn-mpls
evpn-mpls esi esi
show>service>id
7210 SAS-Mxp and 7210 SAS-Sx/S 1/10GE (standalone)
This command displays the existing EVPN-MPLS destinations for a specified service and all related information. Filtering based on esi (for EVPN multihoming) is supported to display the EVPN-MPLS destinations associated to an Ethernet Segment Identifier (ESI).
Specifies a 10-byte ESI by which to filter the displayed information. For example, ESI-0 | ESI-MAX or 00-11-22-33-44-55-66-77-88-99 with any of these separators ('-',':',' ').
The following output is an example of EVPN MPLS information, and Table: Output fields: EVPN MPLS describes the output fields.
Sample output*A:Dut-B# /show service id 1 evpn-mpls
===============================================================================
BGP EVPN-MPLS Dest
===============================================================================
TEP Address Egr Label Num. MACs Mcast Last Change
Transport
-------------------------------------------------------------------------------
10.20.1.3 131069 0 Yes 02/02/2014 15:29:40
rsvp
10.20.1.4 131069 0 Yes 02/02/2014 15:29:33
rsvp
10.20.1.5 131059 0 Yes 02/02/2014 15:29:42
rsvp
-------------------------------------------------------------------------------
Number of entries : 3
-------------------------------------------------------------------------------
===============================================================================
===============================================================================
BGP EVPN-MPLS Ethernet Segment Dest
===============================================================================
Eth SegId Num. Macs Last Change
-------------------------------------------------------------------------------
00:de:01:00:00:00:00:00:00:01 1 02/02/2014 15:47:04
-------------------------------------------------------------------------------
Number of entries: 1
-------------------------------------------------------------------------------
*A:PE-1# show service id 2 evpn-mpls esi 00:10:00:00:00:00:00:00:00:00
|
Label |
Description |
|---|---|
|
TEP Address |
Displays the TEP address |
|
Egr Label |
Displays the egress label |
|
Transport |
Displays the transport type |
|
Number of entries |
Indicates the number of entries |
|
Eth SegId |
Displays the Ethernet segment ID |
|
Transport:Tnl-Id |
Displays the tunnel type and tunnel ID of the EVPN-MPLS entry |
|
Transport:Tnl |
Displays the transport tunnel |
|
Num. MAC |
Displays the number of MACs |
|
Mcast |
Displays the multicast information |
|
Sup BCast Domain |
Displays the Sup BCast Domain |
proxy-arp [ip-address] [detail]
show>service>id
7210 SAS-Mxp and 7210 SAS-Sx/S 1/10GE (standalone)
This command displays, in a table, the existing proxy-ARP entries for a specified service. The table is populated by EVPN MAC routes that contain a MAC and an IP address, as well as static entries or dynamic entries from snooped ARP messages on access SAPs.
A 7210 SAS that receives an ARP request from a SAP performs a lookup in the proxy-ARP table for the service. If a match is found, the router replies to the ARP and does not allow ARP flooding in the VPLS service. If a match is not found, the ARP is flooded within the service if the configuration allows it.
This command allows for specific IP addresses to be displayed. Dynamic IP entries associated to a MAC list are displayed with the corresponding MAC list and resolve timers information.
Specifies an IP address.
Displays detailed information.
The following output is an example of proxy-ARP information for a specified service, and Table: Output fields: proxy-ARP describes the output fields.
Sample outputshow service id 1 proxy-arp detail
-------------------------------------------------------------------------------
Proxy Arp
-------------------------------------------------------------------------------
Admin State : enabled
Dyn Populate : enabled
Age Time : disabled Send Refresh : disabled
Table Size : 16383 Total : 2
Static Count : 0 EVPN Count : 1
Dynamic Count : 1 Duplicate Count : 0
Dup Detect
-------------------------------------------------------------------------------
Detect Window : 3 mins Num Moves : 5
Hold down : 9 mins
Anti Spoof MAC : None
EVPN
-------------------------------------------------------------------------------
Garp Flood : disabled Req Flood : enabled
-------------------------------------------------------------------------------
===============================================================================
VPLS Proxy Arp Entries
===============================================================================
IP Address Mac Address Type Status Last Update
-------------------------------------------------------------------------------
10.1.1.1 00:00:00:00:00:01 dyn active 03/13/2020 10:25:39
10.1.1.10 00:00:00:00:00:11 evpn active 03/13/2020 10:25:40
-------------------------------------------------------------------------------
Number of entries : 2
===============================================================================
|
Label |
Description |
|---|---|
|
Admin State |
Displays the admin state: enabled or disabled |
|
Dyn Populate |
Displays the status of the ARP dynamic population |
|
Age Time |
Displays the configured ARP age timer |
|
Send Refresh |
Displays the configured ARP refresh timer |
|
Table Size |
Displays the configured ARP table size |
|
Total |
Displays the total table used count |
|
Static Count |
Displays the static ARP entries count |
|
EVPN Count |
Displays the count of ARP entries learned through the EVPN tunnel |
|
Dynamic Count |
Displays the count of ARP entries dynamically learned |
|
Duplicate Count |
Displays the count of ARP duplicate entries |
|
Detect Window |
Displays the configured window value for ARP duplicate detection |
|
Num Moves |
Displays the configured count for number of moves used for ARP duplicate detection |
|
Hold Down |
Displays the hold-down timer used by ARP duplicate detection |
|
Anti Spoof MAC |
Displays the MAC address configured for anti-spoof detection |
|
Garp Flood |
Displays the status for GARP flooding |
|
Req Flood |
Displays the status of ARP request flooding |
|
IP Address |
Displays the IP address of the proxy-ARP entry |
|
Mac Address |
Displays the MAC address of the proxy-ARP entry |
|
Type |
Displays the type of ARP entry |
|
Status |
Displays the status |
|
Last Update |
Displays the date and time of the last update |
proxy-nd [ipv6-address] [detail]
show>service>id
7210 SAS-Mxp and 7210 SAS-Sx/S 1/10GE (standalone)
This command displays, in a table, the existing proxy-ND entries for a specified service. The table is populated by the EVPN MAC routes containing a MAC and an IPv6 address, as well as static entries or dynamic entries from snooped NA messages on access SAPs.
A 7210 SAS that receives a Neighbor Solicitation (NS) from a SAP performs a lookup in the proxy-ND table for the service. If a match is found, the router replies to the NS and does not allow NS flooding in the VPLS service. If a match is not found, the NS is flooded in the service, if the configuration allows it.
This command allows specific IPv6 addresses to be displayed. Dynamic IPv6 entries associated to a MAC list are shown with the corresponding MAC list and resolve timer information.
Specifies an IPv6 address.
Displays detailed information.
The following output is an example of proxy-ND information for a specified service, and Table: Output fields: proxy-ND displays the output fields.
Sample outputA:Dut-C# show service id 1 proxy-nd detail
-------------------------------------------------------------------------------
Proxy ND
-------------------------------------------------------------------------------
Admin State : enabled
Dyn Populate : enabled
Age Time : disabled Send Refresh : disabled
Table Size : 250 Total : 1
Static Count : 0 EVPN Count : 0
Dynamic Count : 1 Duplicate Count : 0
Dup Detect
-------------------------------------------------------------------------------
Detect Window : 3 mins Num Moves : 5
Hold down : 9 mins
Anti Spoof MAC : None
EVPN
-------------------------------------------------------------------------------
Unknown NS Flood : enabled ND Advertise : Router
Rtr Unsol NA Flood: disabled Host Unsol NA Fld : disabled
-------------------------------------------------------------------------------
===============================================================================
VPLS Proxy ND Entries
===============================================================================
IP Address Mac Address Type Status Rtr/ Last Update
Host
-------------------------------------------------------------------------------
2000::4 00:00:00:00:00:04 dyn active Rtr 01/14/2020 09:47:43
-------------------------------------------------------------------------------
Number of entries : 1*A:PE-2# show service id 5 proxy-nd
|
Label |
Description |
|---|---|
|
Admin State |
Displays the admin state for proxy-ND: enabled or disabled |
|
Dyn Populate |
Displays the status for dynamic populate |
|
Age Time |
Displays the aging timer for ND entries |
|
Send Refresh |
Displays the refresh timer for ND entries |
|
Table Size |
Displays the proxy-ND table size |
|
Total |
Displays the count of learned ND entries |
|
Static Count |
Displays the count of static ND entries |
|
EVPN Count |
Displays the count of ND entries learned from the EVPN binding |
|
Dynamic Count |
Displays the count of dynamically learned ND entries |
|
Duplicate Count |
Displays the count of duplicate ND entries |
|
Detect Window |
Displays the configured value for window size used for duplicate detection |
|
Num Moves |
Displays the configured value for number of moves used in duplicate ND detection |
|
Hold Down |
Displays the value of the hold-down timer |
|
Anti Spoof MAC |
Displays the configured anti-spoof MAC address |
|
Unknown NS Flood |
Displays the state of unknown Neighbor Solicitation messages that are flooded to the EVPN network |
|
ND Advertise |
Displays the advertisement of static or dynamic entries that are learned as hosts or routers |
|
Rtr Unsol NA Flood |
Displays the state of system floods router unsolicited Neighbor Advertisements to EVPN |
|
Host Unsol NA Fld |
Displays the state of system floods host unsolicited Neighbor Advertisements to EVPN |
|
IP Address |
Displays the IP address of the proxy-ND entry |
|
Mac Address |
Displays the MAC address of the proxy-ND entry |
|
Type |
Displays the type of ND entry |
|
Status |
Displays the status of the ND entry |
|
Last Update |
Displays the date and time of the last update |
system
show>service
7210 SAS-Mxp and 7210 SAS-Sx/S 1/10GE (standalone)
Commands in this context configure the system BGP EVPN show commands.
bgp-evpn
bgp-evpn ethernet-segment
bgp-evpn ethernet-segment name name [all]
bgp-evpn ethernet-segment name name evi [evi]
show>service>system
7210 SAS-Mxp and 7210 SAS-Sx/S 1/10GE (standalone)
This command displays system BGP EVPN information.
Displays Ethernet Segment (ES) information.
Specifies the ES name, up to 28 characters.
Displays all available information for the specified ES.
Displays information for the specified EVI.
The following output is an example of system BGP EVPN information, and Table: Output fields: system BGP-EVPN describes the output fields.
Sample output*A:Dut-B# /show service system bgp-evpn
===============================================================================
System BGP EVPN Information
===============================================================================
Evpn Route Dist. : <none>
Oper Route Dist. : 10.20.1.2:0
Oper Route Dist Type : default
===============================================================================
|
Label |
Description |
|---|---|
|
Evpn Route Dist. |
Displays the EVPN route distinguisher |
|
Oper Route Dist. |
Displays address of the operational route distinguisher |
|
Oper Route Dist Type |
Displays the operational route distinguisher type |
redundancy
show
7210 SAS-Mxp and 7210 SAS-Sx/S 1/10GE (standalone)
Commands in this context display the global redundancy parameters.
bgp-evpn-multi-homing
show>redundancy
7210 SAS-Mxp and 7210 SAS-Sx/S 1/10GE (standalone)
This command displays information related to the EVPN global timers.
The following output is an example of BGP EVPN multi-homing information, and Table: Output Fields: BGP-EVPN multi-homing displays the output fields.
Sample output*A:Dut-B# show redundancy bgp-evpn-multi-homing
===============================================================================
Redundancy BGP EVPN Multi-homing Information
===============================================================================
Boot-Timer : 10 secs
Boot-Timer Remaining : 0 secs
ES Activation Timer : 3 secs
===============================================================================
|
Label |
Description |
|---|---|
|
Boot-Timer |
Displays the value configured for the boot timer |
|
Boot-Timer Remaining |
Displays the amount of time remaining on the boot timer |
|
ES Activation Timer |
Displays the value configured for the ES activation timer |