eth-cfm
show
7210 SAS-T (network operating mode)
This command displays 802.1ag CFM information.
association [ma-index] [detail]
show>eth-cfm
7210 SAS-T (network operating mode)
This command displays association information.
Specifies the MA index value.
Displays all association detail.
The following output is an example of Ethernet CFM associations information, and Table: Output fields: ETH-CFM associations describes the output fields.
Sample output*A:alcag1-R6# show eth-cfm association
======================================================================
CFM Association Table
======================================================================
Md-index Ma-index Name CCM-interval Bridge-id
----------------------------------------------------------------------
1 1 ivpls 1 5000
======================================================================
*A:alcag1-R6#
|
Label |
Description |
|---|---|
|
Md-index |
Displays the MD index |
|
Ma-index |
Displays the MA index |
|
Name |
Displays the name of the MA |
|
CCM-interval |
Displays the CCM interval (in seconds) |
|
Bridge-id |
Displays the bridge ID for the MA. The bridge ID is the same value as the service ID of the service to which the MEP belongs. |
cfm-stack-table
cfm-stack-table port [port-id> [vlan qtag[.qtag]] [level 0..7] [direction up | down]
cfm-stack-table sdp [sdp-id[:vc-id]>] [level 0..7]] [direction up | down]
cfm-stack-table virtual [service-id] [level 0..7]
show>eth-cfm
7210 SAS-T (network operating mode)
This command summarizes all MEPs or MIPs.
Displays information about the specified port.
Specfies an existing SDP and VC ID.
Specifies the qtag value.
Specifies the level.
Indicates the direction in which the maintenance association (MEP or MIP) faces on the bridge port.
down — Displays continuity check information configured away from the MAC relay entity.
up — Displays continuity check information configured toward the MAC relay entity.
Specifies information about the specified service ID.
The following output is an example of Ethernet CFM stack-table information, and Table: Output fields: ETH-CFM stack table describes the output fields.
Sample output*A:alcag1-R6# show eth-cfm cfm-stack-table
========================================================================
CFM SAP Stack Table
========================================================================
Sap Level Dir Md-index Ma-index Mep-id Mac-address
------------------------------------------------------------------------
1/2/9:5 4 Up 1 1 51 00:ae:ae:ae:ae:ae
========================================================================
CFM SDP Stack Table
========================================================================
Sdp Level Dir Md-index Ma-index Mep-id Mac-address
------------------------------------------------------------------------
No Matching Entries
========================================================================
*A:alcag1-R6#
|
Label |
Description |
|---|---|
|
Sap |
Displays the SAP identifier. |
|
Sdp |
Displays the spoke SDP identifier. |
|
Level |
Displays the MD level of the domain. |
|
Dir (direction) |
Displays the direction of OAMPDU transmission. |
|
Md-index |
Displays the MD index of the domain. |
|
Ma-index |
Displays the MA index of the domain. |
|
Mep-id |
Displays the MEP identifier. |
|
Mac-address |
Displays the MAC address of the MEP. |
domain [md-index] [association ma-index | all-associations [detail]]
show>eth-cfm>domain
7210 SAS-T (network operating mode)
This command displays domain information.
Specifies the maintenance domain (MD) index value.
Specifies the MA index value.
Displays information all maintenance associations.
Displays detailed information.
The following output is an example of Ethernet CFM domain information, and Table: ETH-CFM domain field descriptions describes the output fields.
Sample output*A:alcag1-R6# show eth-cfm domain
==============================================================================
CFM Domain Table
==============================================================================
Md-index Level Name Format
------------------------------------------------------------------------------
1 4 ivpls charString
==============================================================================
*A:alcag1-R6#
*A:alcag1-R6# show eth-cfm mep 51 domain 1 association 1
-------------------------------------------------------------------------------
Mep Information
-------------------------------------------------------------------------------
Md-index : 1 Direction : Up
Ma-index : 1 Admin : Enabled
MepId : 51 CCM-Enable : Enabled
IfIndex : 38043648 PrimaryVid : 5
FngState : fngReset
LowestDefectPri : allDef HighestDefect : none
Defect Flags : None
Mac Address : 00:ae:ae:ae:ae:ae CcmLtmPriority : 7
CcmTx : 775 CcmSequenceErr : 0
CcmLastFailure Frame:
None
XconCcmFailure Frame:
None
*A:alcag1-R6#
|
Label |
Description |
|---|---|
|
Domain |
|
|
Md-index |
Displays the MD index of the domain |
|
Level |
Displays the MD level of the domain |
|
Name |
Displays the name of the MD |
|
Format |
Displays the format for the MD name |
|
Domain Associations |
|
|
Md-index |
Displays the MD index of the domain |
|
Direction |
Displays the direction of OAMPDU transmission |
|
Ma-index |
Displays the MA index of the association |
|
Admin |
Displays the administrative status of the MEP |
|
MepId |
Displays the MEP identifier |
|
CCM-Enable |
Displays the status of the CCM (enabled or disabled) |
|
IfIndex |
Displays the index of the interface |
|
PrimaryVid |
Displays the identifier of the primary VLAN |
|
FngState |
Indicates the different states of the Fault Notification Generator |
|
LowestDefectPri |
Displays the lowest priority defect (a configured value) that is allowed to generate a fault alarm |
|
HighestDefect |
Identifies the highest defect that is present (for example, if defRDICCM and defXconCCM are present, the highest defect is defXconCCM) |
|
Defect Flags |
Displays the number of defect flags |
|
Mac Address |
Displays the MAC address of the MEP |
|
CcmLtmPriority |
Displays the priority value transmitted in the linktrace messages (LTM)s and CCMs for this MEP. The MEP must be configured on a VLAN. |
|
CcmTx |
Displays the number of Continuity Check Messages (CCM) sent. The count is taken from the last polling interval (every 10 s). |
|
CcmSequenceErr |
Displays the number of CCM errors |
|
CcmLastFailure Frame |
Displays the frame that caused the last CCM failure |
|
XconCcmFailure Frame |
Displays the frame that caused the XconCCMFailure |
mep mep-id domain md-index association ma-index [loopback] [linktrace]
show>eth-cfm>domain
7210 SAS-T (network operating mode)
This command displays Maintenance Endpoint (MEP) information.
Specifies the maintenance association end point identifier.
Specifies the maintenance domain (MD) index value.
Specifies the MA index value.
Displays loopback information for the specified MEP.
Displays linktrace information for specified MEP.
The following output is an example of MEP information, and Table: Output fields: MEP describes the output fields.
Sample output*A:alcag1-R6# oam eth-cfm loopback 00:af:af:af:af:af mep 51 domain 1 association 1
eth-cfm Loopback Test Initiated: Mac-Address: 00:af:af:af:af:af, out sap: 1/2/9:5
Sent 1 packets, received 1 packets [0 out-of-order, 0 Bad Msdu] -- OK
*A:alcag1-R6#
*A:alcag1-R6# oam eth-cfm linktrace 00:af:af:af:af:af mep 51 domain 1 association 1
Index Ingress Mac Egress Mac Relay Action
----- -------------------- -------------------- ---------- ----------
1 00:00:00:00:00:00 00:AF:AF:AF:AF:AF rlyHit terminate
----- -------------------- -------------------- ---------- ----------
No more responses received in the last 5 seconds.
*A:alcag1-R6#
|
Label |
Description |
|---|---|
|
Index |
Displays the index of the domain |
|
Relay |
Displays the value returned in the Relay Action field |
|
IngressMac |
Displays the MAC address returned in the ingress MAC address field |
|
Action |
Displays the value returned in the Action field of the linktrace message |
|
EgressMac |
Displays the MAC address returned in the egress MAC address field |
mip
show>eth-cfm>mip
7210 SAS-T (network operating mode)
This command displays Maintenance Intermediate Point (MIP) information.
The following output is an example of Ethernet CFM MIP information, and Table: Output fields: MIP describes the output fields.
Sample output*A:7210SAS# show eth-cfm mip
==========================================================================
CFM SAP MIP Table
==========================================================================
Sap Mip-Enabled Mip Mac Address
--------------------------------------------------------------------------
1/1/16 yes 00:a1:b1:c1:d1:e1
==========================================================================
==========================================================================
CFM SDP MIP Table
==========================================================================
Sdp Mip-Enabled Mip Mac Address
--------------------------------------------------------------------------
456:123 yes 00:a2:b2:c2:d2:e2
==========================================================================
*A:7210SAS#
|
Label |
Description |
|---|---|
|
Mip-Enabled |
Displays the state of the MIP service |
|
Mip Mac Address |
Indicates the Mac Address of the MIP |
id service-id
show>service
7210 SAS-T (network operating mode)
This command displays information about a specific service ID.
The unique service identification number that identifies the service in the service domain.
Displays detailed information about the service.
Displays basic service information.
Displays FDB entries.
Displays the Epipe services associated with the B-VPLS service.
Displays the I-VPLS services associated with this B-VPLS service.
Display STP information.
all
show>service>id
7210 SAS-T (network operating mode)
This command displays detailed information for all aspects of the service.
The following output is an example of detailed information for all aspects of a service, and Table: Output fields: service ID all describes the output fields.
Sample outputSample output for PBB Epipe:
*A:7210-SAS>show>service# id 1000 all
===============================================================================
Service Detailed Information
===============================================================================
Service Id : 1000 Vpn Id : 0
Service Type : Epipe
Description : (Not Specified)
Customer Id : 1
Last Status Change: 04/04/2001 22:18:48
Last Mgmt Change : 04/04/2001 21:28:34
Admin State : Up Oper State : Up
MTU : n/a
MTU Check : n/a
Vc Switching : False
SAP Count : 1 SDP Bind Count : 0
Uplink Type: : MPLS
-------------------------------------------------------------------------------
Service Destination Points(SDPs)
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
Service Access Points
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
SAP 1/1/15:1000
-------------------------------------------------------------------------------
Service Id : 1000
SAP : 1/1/15:1000 Encap : q-tag
Description : (Not Specified)
Admin State : Up Oper State : Up
Flags : None
Last Status Change : 04/04/2001 21:29:23
Last Mgmt Change : 04/04/2001 21:28:34
Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100
Split Horizon Group: (Not Specified)
Admin MTU : 1518 Oper MTU : 1518
Ingr IP Fltr-Id : n/a Egr IP Fltr-Id : n/a
Ingr Mac Fltr-Id : n/a Egr Mac Fltr-Id : n/a
Ingr IPv6 Fltr-Id : n/a Egr IPv6 Fltr-Id : n/a
tod-suite : None
Endpoint : N/A
Acct. Pol : None Collect Stats : Disabled
-------------------------------------------------------------------------------
QOS
-------------------------------------------------------------------------------
Ingress qos-policy : 1
-------------------------------------------------------------------------------
Aggregate Policer
-------------------------------------------------------------------------------
rate : n/a burst : n/a
-------------------------------------------------------------------------------
Ingress QoS Classifier Usage
-------------------------------------------------------------------------------
Classifiers Allocated: 4 Meters Allocated : 2
Classifiers Used : 1 Meters Used : 1
-------------------------------------------------------------------------------
Sap Statistics
-------------------------------------------------------------------------------
Packets Octets
Ingress Stats: 0 0
Egress Stats: 0 0
Ingress Drop Stats: 0 0
Extra-Tag Drop Stats: n/a n/a
-------------------------------------------------------------------------------
Sap per Meter stats (in/out counter mode)
-------------------------------------------------------------------------------
Packets Octets
Ingress Meter 1 (Unicast)
For. InProf : 0 0
For. OutProf : 0 0
-------------------------------------------------------------------------------
PBB Tunnel Point
-------------------------------------------------------------------------------
B-vpls Backbone-dest-MAC Isid AdmMTU OperState Flood Oper-dest-MAC
-------------------------------------------------------------------------------
2 8c:90:d3:79:b2:65 1000 1514 Up Yes 8c:90:d3:79:b2:65
-------------------------------------------------------------------------------
Last Status Change: 04/04/2001 22:18:48
Last Mgmt Change: 04/04/2001 22:18:48
-------------------------------------------------------------------------------
Service Endpoints
-------------------------------------------------------------------------------
No Endpoints found.
===============================================================================
*A:7210-SAS>show>service#
Sample output for I-VPLS:
*A:7210-SAS>show>service# id 200 all
===============================================================================
Service Detailed Information
===============================================================================
Service Id : 200 Vpn Id : 0
Service Type : i-VPLS
Description : (Not Specified)
Customer Id : 1
Last Status Change: 04/04/2001 22:14:30
Last Mgmt Change : 04/04/2001 22:15:06
Admin State : Up Oper State : Up
MTU : n/a
MTU Check : n/a
SAP Count : 1 SDP Bind Count : 0
Snd Flush on Fail : Disabled
Uplink Type: : MPLS
b-Vpls Id : 2 Oper ISID : 200
b-Vpls Status : Up
-------------------------------------------------------------------------------
Split Horizon Group specifics
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Service Destination Points(SDPs)
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
Service Access Points
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
SAP 1/1/15:200
-------------------------------------------------------------------------------
Service Id : 200
SAP : 1/1/15:200 Encap : q-tag
Description : (Not Specified)
Admin State : Up Oper State : Up
Flags : None
Last Status Change : 04/04/2001 22:14:30
Last Mgmt Change : 04/04/2001 22:14:22
Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100
Split Horizon Group: (Not Specified)
Max Nbr of MAC Addr: No Limit Total MAC Addr : 0
Learned MAC Addr : 0 Static MAC Addr : 0
Admin MTU : 1518 Oper MTU : 1518
Ingr IP Fltr-Id : n/a Egr IP Fltr-Id : n/a
Ingr Mac Fltr-Id : n/a Egr Mac Fltr-Id : n/a
Ingr IPv6 Fltr-Id : n/a Egr IPv6 Fltr-Id : n/a
tod-suite : None
Mac Learning : Enabled Discard Unkwn Srce: Disabled
Mac Aging : Enabled Mac Pinning : Disabled
BPDU Translation : Disabled
L2PT Termination : Disabled
Acct. Pol : None Collect Stats : Disabled
-------------------------------------------------------------------------------
Stp Service Access Point specifics
-------------------------------------------------------------------------------
Stp Admin State : Up Stp Oper State : Down
Core Connectivity : Down
Port Role : N/A Port State : Forwarding
Port Number : 2049 Port Priority : 128
Port Path Cost : 10 Auto Edge : Enabled
Admin Edge : Disabled Oper Edge : N/A
Link Type : Pt-pt BPDU Encap : Dot1d
Root Guard : Disabled Active Protocol : N/A
Last BPDU from : N/A
CIST Desig Bridge : N/A Designated Port : N/A
Forward transitions: 0 Bad BPDUs rcvd : 0
Cfg BPDUs rcvd : 0 Cfg BPDUs tx : 0
TCN BPDUs rcvd : 0 TCN BPDUs tx : 0
TC bit BPDUs rcvd : 0 TC bit BPDUs tx : 0
RST BPDUs rcvd : 0 RST BPDUs tx : 0
MST BPDUs rcvd : 0 MST BPDUs tx : 0
-------------------------------------------------------------------------------
ARP host
-------------------------------------------------------------------------------
Admin State : outOfService
Host Limit : 1 Min Auth Interval : 15 minutes
-------------------------------------------------------------------------------
QOS
-------------------------------------------------------------------------------
Ingress qos-policy : 1
-------------------------------------------------------------------------------
Aggregate Policer
-------------------------------------------------------------------------------
rate : n/a burst : n/a
-------------------------------------------------------------------------------
Ingress QoS Classifier Usage
-------------------------------------------------------------------------------
Classifiers Allocated: 4 Meters Allocated : 2
Classifiers Used : 2 Meters Used : 2
-------------------------------------------------------------------------------
Sap Statistics
-------------------------------------------------------------------------------
Packets Octets
Ingress Stats: 0 0
Egress Stats: 0 0
Ingress Drop Stats: 0 0
Extra-Tag Drop Stats: n/a n/a
-------------------------------------------------------------------------------
Sap per Meter stats (in/out counter mode)
-------------------------------------------------------------------------------
Packets Octets
Ingress Meter 1 (Unicast)
For. InProf : 0 0
For. OutProf : 0 0
Ingress Meter 11 (Multipoint)
For. InProf : 0 0
For. OutProf : 0 0
-------------------------------------------------------------------------------
VPLS Spanning Tree Information
-------------------------------------------------------------------------------
VPLS oper state : Up Core Connectivity : Down
Stp Admin State : Down Stp Oper State : Down
Mode : Rstp Vcp Active Prot. : N/A
Bridge Id : 80:00.00:25:ba:08:f6:20 Bridge Instance Id: 0
Bridge Priority : 32768 Tx Hold Count : 6
Topology Change : Inactive Bridge Hello Time : 2
Last Top. Change : 0d 00:00:00 Bridge Max Age : 20
Top. Change Count : 0 Bridge Fwd Delay : 15
Root Bridge : N/A
Primary Bridge : N/A
Root Path Cost : 0 Root Forward Delay: 0
Rcvd Hello Time : 0 Root Max Age : 0
Root Priority : 0 Root Port : N/A
-------------------------------------------------------------------------------
Forwarding Database specifics
-------------------------------------------------------------------------------
Service Id : 200 Mac Move : Disabled
Mac Move Rate : 2 Mac Move Timeout : 10
Mac Move Retries : 3
Table Size : 250 Total Count : 0
Learned Count : 0 Static Count : 0
Remote Age : 900 Local Age : 300
High Watermark : 95% Low Watermark : 90%
Mac Learning : Enabled Discard Unknown : Disabled
Mac Aging : Enabled Relearn Only : False
===============================================================================
Sample output for B-VPLS service:
*A:7210-SAS>show>service# id 2 all
===============================================================================
Service Detailed Information
===============================================================================
Service Id : 2 Vpn Id : 0
Service Type : b-VPLS
Description : (Not Specified)
Customer Id : 1
Last Status Change: 04/04/2001 22:13:57
Last Mgmt Change : 04/04/2001 22:13:57
Admin State : Up Oper State : Up
MTU : n/a
MTU Check : n/a
SAP Count : 1 SDP Bind Count : 0
Snd Flush on Fail : Disabled
Uplink Type: : MPLS
Oper Backbone Src : 00:25:ba:08:f6:20
i-Vpls Count : 1
Epipe Count : 1
-------------------------------------------------------------------------------
Split Horizon Group specifics
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Service Destination Points(SDPs)
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
Service Access Points
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
SAP 1/1/2:2
-------------------------------------------------------------------------------
Service Id : 2
SAP : 1/1/2:2 Encap : q-tag
Description : (Not Specified)
Admin State : Up Oper State : Up
Flags : None
Last Status Change : 04/04/2001 22:13:57
Last Mgmt Change : 04/04/2001 22:13:54
Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100
PBB Ethertype : 0x88e7
Split Horizon Group: (Not Specified)
Max Nbr of MAC Addr: No Limit Total MAC Addr : 0
Learned MAC Addr : 0 Static MAC Addr : 0
Admin MTU : 1518 Oper MTU : 1518
Ingr Mac Fltr-Id : n/a Egr Mac Fltr-Id : n/a
tod-suite : None
Mac Learning : Enabled Discard Unkwn Srce: Disabled
Mac Aging : Enabled Mac Pinning : Disabled
BPDU Translation : Disabled
L2PT Termination : Disabled
Acct. Pol : None Collect Stats : Disabled
-------------------------------------------------------------------------------
Stp Service Access Point specifics
-------------------------------------------------------------------------------
Stp Admin State : Up Stp Oper State : Down
Core Connectivity : Down
Port Role : N/A Port State : Forwarding
Port Number : 2048 Port Priority : 128
Port Path Cost : 10 Auto Edge : Enabled
Admin Edge : Disabled Oper Edge : N/A
Link Type : Pt-pt BPDU Encap : Dot1d
Root Guard : Disabled Active Protocol : N/A
Last BPDU from : N/A
CIST Desig Bridge : N/A Designated Port : N/A
Forward transitions: 0 Bad BPDUs rcvd : 0
Cfg BPDUs rcvd : 0 Cfg BPDUs tx : 0
TCN BPDUs rcvd : 0 TCN BPDUs tx : 0
TC bit BPDUs rcvd : 0 TC bit BPDUs tx : 0
RST BPDUs rcvd : 0 RST BPDUs tx : 0
MST BPDUs rcvd : 0 MST BPDUs tx : 0
-------------------------------------------------------------------------------
ARP host
-------------------------------------------------------------------------------
Admin State : outOfService
Host Limit : 1 Min Auth Interval : 15 minutes
-------------------------------------------------------------------------------
QOS
-------------------------------------------------------------------------------
Ingress qos-policy : 1
-------------------------------------------------------------------------------
Aggregate Policer
-------------------------------------------------------------------------------
rate : n/a burst : n/a
-------------------------------------------------------------------------------
Ingress QoS Classifier Usage
-------------------------------------------------------------------------------
Classifiers Allocated: 4 Meters Allocated : 2
Classifiers Used : 2 Meters Used : 2
-------------------------------------------------------------------------------
Sap Statistics
-------------------------------------------------------------------------------
Packets Octets
Ingress Stats: 0 0
Egress Stats: 0 0
Ingress Drop Stats: 0 0
Extra-Tag Drop Stats: n/a n/a
-------------------------------------------------------------------------------
Sap per Meter stats (in/out counter mode)
-------------------------------------------------------------------------------
Packets Octets
Ingress Meter 1 (Unicast)
For. InProf : 0 0
For. OutProf : 0 0
Ingress Meter 11 (Multipoint)
For. InProf : 0 0
For. OutProf : 0 0
-------------------------------------------------------------------------------
VPLS Spanning Tree Information
-------------------------------------------------------------------------------
VPLS oper state : Up Core Connectivity : Down
Stp Admin State : Down Stp Oper State : Down
Mode : Rstp Vcp Active Prot. : N/A
Bridge Id : 80:00.00:25:ba:08:f6:20 Bridge Instance Id: 0
Bridge Priority : 32768 Tx Hold Count : 6
Topology Change : Inactive Bridge Hello Time : 2
Last Top. Change : 0d 00:00:00 Bridge Max Age : 20
Top. Change Count : 0 Bridge Fwd Delay : 15
Root Bridge : N/A
Primary Bridge : N/A
Root Path Cost : 0 Root Forward Delay: 0
Rcvd Hello Time : 0 Root Max Age : 0
Root Priority : 0 Root Port : N/A
-------------------------------------------------------------------------------
Forwarding Database specifics
-------------------------------------------------------------------------------
Service Id : 2 Mac Move : Disabled
Mac Move Rate : 2 Mac Move Timeout : 10
Mac Move Retries : 3
Table Size : 250 Total Count : 0
Learned Count : 0 Static Count : 0
Remote Age : 900 Local Age : 300
High Watermark : 95% Low Watermark : 90%
Mac Learning : Enabled Discard Unknown : Disabled
Mac Aging : Enabled Relearn Only : False
-------------------------------------------------------------------------------
Related i-Vpls services for b-Vpls service 2
-------------------------------------------------------------------------------
i-Vpls SvcId Oper ISID Admin Oper
-------------------------------------------------------------------------------
200 200 Up Up
-------------------------------------------------------------------------------
Number of Entries : 1
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Related Epipe services for b-Vpls service 2
-------------------------------------------------------------------------------
Epipe SvcId Oper ISID Admin Oper
-------------------------------------------------------------------------------
1000 1000 Up Up
-------------------------------------------------------------------------------
Number of Entries : 1
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Service Endpoints
-------------------------------------------------------------------------------
No Endpoints found.
===============================================================================
*A:7210-SAS>show>service#
|
Label |
Description |
|---|---|
|
|
The service identifier. |
|
|
Specifies the type of service. |
|
|
Generic information about the service. |
|
|
The customer identifier. |
|
|
The date and time of the most recent status change to this customer. |
|
|
The date and time of the most recent management-initiated change to this customer. |
|
|
The administrative state of the service. |
|
|
Displays the status of VC switching. |
|
|
The number of SAPs specified for this service. |
|
|
Displays the mode of the device. |
|
|
The number which identifies the VPN. |
|
|
The operational state of the service. |
|
|
Displays the SAP ID. |
|
|
The value of the label used to identify this SAP on the access port. |
|
|
Displays the configured QinQ Ethertype value. |
|
|
Displays the configured Dot1Q Ethertype value. |
|
|
Displays the split horizon group information. |
|
|
The desired largest service frame size (in octets) that can be transmitted through the port to the far-end router, without requiring the packet to be fragmented. |
|
|
The actual largest service frame size (in octets) that can be transmitted through the port to the far-end router, without requiring the packet to be fragmented. |
|
|
Ingress IP filter ID. |
|
|
Egress IP filter ID. |
|
|
Ingress MAC filter ID. |
|
|
Egress MAC filter ID. |
|
|
Ingress IPv6 filter ID. |
|
|
Egress IPv6 filter ID. |
|
|
Displays the endpoint name. |
|
|
Indicates the accounting policy applied to the SAP. |
|
|
Specifies whether accounting statistics are collected on the SAP. |
|
QoS parameters |
|
|
|
The SAP ingress QoS policy ID. |
|
|
Displays the number of classifiers allocated. |
|
|
Displays the number of classifiers used. |
|
|
Displays the number of meters allocated. |
|
|
Displays the number of meters used. |
|
|
The number of received packets/octets for this SAP. |
|
|
The number of packets/octets forwarded out of this SAP. |
|
PBB Tunnel Point parameters |
|
|
|
Displays the B-VPLS ID. |
|
|
Displays the back bone destination MAC address. |
|
|
Displays the ISID number. |
|
|
Specifies whether or not the traffic is flooded in the B-VPLS for the Destination instead of unicast. If the backbone destination MAC is in theB-VPLS FDB, it is unicast. |
|
|
Displays the operational destination MAC address. |
|
|
Displays the count of I-VPLS bound to B-VPLS. |
|
|
Displays the operational state of the B-VPLS service. |
|
|
Displays the count of Epipe bound to B-VPLS. |
base
show>service>id
7210 SAS-T (network operating mode)
This command displays basic information about the service including service type, description and SAPs.
The following output is an example of basic service information, and Table: Output fields: base describes the output fields.
Sample outputSample output for PBB Epipe service:
*A:7210-SAS>show>service# id 1000 base
===============================================================================
Service Basic Information
===============================================================================
Service Id : 1000 Vpn Id : 0
Service Type : Epipe
Description : (Not Specified)
Customer Id : 1
Last Status Change: 04/04/2001 22:18:48
Last Mgmt Change : 04/04/2001 21:28:34
Admin State : Up Oper State : Up
MTU : n/a
MTU Check : n/a
Vc Switching : False
SAP Count : 1 SDP Bind Count : 0
Uplink Type: : MPLS
-------------------------------------------------------------------------------
Service Access & Destination Points
-------------------------------------------------------------------------------
Identifier Type AdmMTU OprMTU Adm Opr
-------------------------------------------------------------------------------
sap:1/1/15:1000 q-tag 1518 1518 Up Up
-------------------------------------------------------------------------------
PBB Tunnel Point
-------------------------------------------------------------------------------
B-vpls Backbone-dest-MAC Isid AdmMTU OperState Flood Oper-dest-MAC
-------------------------------------------------------------------------------
2 8c:90:d3:79:b2:65 1000 1514 Up Yes 8c:90:d3:79:b2:65
-------------------------------------------------------------------------------
Last Status Change: 04/04/2001 22:18:48
Last Mgmt Change: 04/04/2001 22:18:48
===============================================================================
*A:7210-SAS>show>service#
Sample output for I-VPLS service:
*A:7210-SAS>show>service# id 200 base
===============================================================================
Service Basic Information
===============================================================================
Service Id : 200 Vpn Id : 0
Service Type : i-VPLS
Description : (Not Specified)
Customer Id : 1
Last Status Change: 04/04/2001 22:14:30
Last Mgmt Change : 04/04/2001 22:15:06
Admin State : Up Oper State : Up
MTU : n/a
MTU Check : n/a
SAP Count : 1 SDP Bind Count : 0
Snd Flush on Fail : Disabled
Uplink Type: : MPLS
b-Vpls Id : 2 Oper ISID : 200
b-Vpls Status : Up
-------------------------------------------------------------------------------
Service Access & Destination Points
-------------------------------------------------------------------------------
Identifier Type AdmMTU OprMTU Adm Opr
-------------------------------------------------------------------------------
sap:1/1/15:200 q-tag 1518 1518 Up Up
===============================================================================
*A:7210-SAS>show>service#
Sample output for B-VPLS service:
*A:7210-SAS>show>service# id 2 base
===============================================================================
Service Basic Information
===============================================================================
Service Id : 2 Vpn Id : 0
Service Type : b-VPLS
Description : (Not Specified)
Customer Id : 1
Last Status Change: 04/04/2001 22:13:57
Last Mgmt Change : 04/04/2001 22:13:57
Admin State : Up Oper State : Up
MTU : n/a
MTU Check : n/a
SAP Count : 1 SDP Bind Count : 0
Snd Flush on Fail : Disabled
Uplink Type: : MPLS
Oper Backbone Src : 00:25:ba:08:f6:20
i-Vpls Count : 1
Epipe Count : 1
-------------------------------------------------------------------------------
Service Access & Destination Points
-------------------------------------------------------------------------------
Identifier Type AdmMTU OprMTU Adm Opr
-------------------------------------------------------------------------------
sap:1/1/2:2 q-tag 1518 1518 Up Up
===============================================================================
*A:7210-SAS>show>service#
|
Label |
Description |
|---|---|
|
Service Id |
The service identifier. |
|
Service Type |
Specifies the type of service. |
|
Description |
Generic information about the service. |
|
Customer Id |
The customer identifier. |
|
Last Status Change |
The date and time of the most recent status change to this customer. |
|
Last Mgmt Change |
The date and time of the most recent management-initiated change to this customer. |
|
Admin State |
The administrative state of the service. |
|
Vc Switching |
Displays the status of VC switching. |
|
SAP Count |
The number of SAPs specified for this service. |
|
Uplink Type |
Displays the mode of the device. |
|
Vpn Id |
The number which identifies the VPN. |
|
Oper State |
The operational state of the service. |
|
SAP |
Displays the SAP ID. |
|
Encap |
The value of the label used to identify this SAP on the access port. |
|
Vpn Id |
The number which identifies the VPN. |
|
Oper State |
The operational state of the service. |
|
SAP |
Displays the SAP ID. |
|
PBB Tunnel Point |
|
|
B-vpls |
Displays the B-VPLS ID. |
|
Backbone-dest-MAC |
Displays the back bone destination MAC address. |
|
Isid |
Displays the ISID number. |
|
Flood |
Specifies whether or not the traffic is flooded in the B-VPLS for the Destination instead of unicast. If the backbone destination MAC is in theB-VPLS FDB, it is unicast. |
|
b-Vpls Status |
Displays the operational state of the B-VPLS service. |
|
b-Vpls Id |
Displays the B-VPLS ID. |
fdb {info | mac ieee-address | sap sap-id | detail | endpoint endpoint}
[expiry] [pbb]
show>service>id
7210 SAS-T (network operating mode)
This command displays FDB entries for a specific MAC address.
Specifies the physical port identifier portion of the SAP.
Displays detailed information.
Displays time until MAC is aged out.
Displays endpoint information.
Displays PBB information.
The following output is an example of FDB entry information, and Table: Output fields: FDB describes the output fields.
Sample output*A:7210-SAS>show>service# id 200 fdb
===============================================================================
Forwarding Database, Service 200
===============================================================================
Service Id : 200 Mac Move : Disabled
Mac Move Rate : 2 Mac Move Timeout : 10
Mac Move Retries : 3
Table Size : 250 Total Count : 0
Learned Count : 0 Static Count : 0
Remote Age : 900 Local Age : 300
High Watermark : 95% Low Watermark : 90%
Mac Learning : Enabled Discard Unknown : Disabled
Mac Aging : Enabled Relearn Only : False
===============================================================================
*A:7210-SAS>show>service#
*A:7210-SAS>show>service# id 2 fdb
===============================================================================
Forwarding Database, Service 2
===============================================================================
Service Id : 2 Mac Move : Disabled
Mac Move Rate : 2 Mac Move Timeout : 10
Mac Move Retries : 3
Table Size : 250 Total Count : 0
Learned Count : 0 Static Count : 0
Remote Age : 900 Local Age : 300
High Watermark : 95% Low Watermark : 90%
Mac Learning : Enabled Discard Unknown : Disabled
Mac Aging : Enabled Relearn Only : False
===============================================================================
*A:7210-SAS>show>service#
|
Label |
Description |
|---|---|
|
Service Id |
Displays the service ID. |
|
Mac Move Rate |
Displays the maximum rate at which MAC's can be relearned in this service, before the SAP where the moving MAC was last seen is automatically disabled to protect the system against undetected loops or duplicate MAs. The rate is computed as the maximum number of relearns allowed in a 5 second interval: for example, the default rate of 2 relearns per second corresponds to 10 relearns in a 5 second period. |
|
Mac Move Retries |
Displays the number of times retries are performed for reenabling the SAP. |
|
Table Size |
Specifies the maximum number of learned and static entries allowed in the FDB of this service. |
|
Learned Count |
Displays the current number of learned entries in the FDB of this service. |
|
Remote Age |
Displays the number of seconds used to age out FDB entries learned on an SAP. These entries correspond to MAC addresses learned on remote SAPs. |
|
High Watermark |
Displays the utilization of the FDB table of this service at which a table full alarm is raised by the agent. |
|
Mac Learning |
Specifies whether the MAC learning process is enabled |
|
Mac Aging |
Indicates whether the MAC aging process is enabled. |
|
Mac Move |
Displays the administrative state of the MAC movement feature associated with this service. |
|
Mac Move Timeout |
Displays the time in seconds to wait before a SAP that has been disabled after exceeding the maximum relearn rate is re-enabled. A value of zero indicates that the SAP is automatically re-enabled after being disabled. If after the SAP is re-enabled it is disabled again, the effective retry timeout is doubled to avoid thrashing. |
|
Total Count |
Displays the total number of learned entries in the FDB of this service. |
|
Static Count |
Displays the current number of static entries in the FDB of this service. |
|
Local Age |
Displays the number of seconds used to age out FDB entries learned on local SAPs. |
|
Low Watermark |
Displays the utilization of the FDB table of this service at which a table full alarm is cleared by the agent. |
|
Discard Unknown |
Specifies whether frames received with an unknown destination MAC are discarded. |
|
Relearn Only |
Displays, that when enabled, either the FDB table of this service is full, or that the maximum system-wide number of MAC's supported by the agent has been reached, and therefore MAC learning is temporary disabled, and only MAC relearns can take place. |
stp [detail]
show>service>id
7210 SAS-T (network operating mode)
This command displays information for the spanning tree protocol (STP) instance for the service.
Displays detailed information.
The following output is an example of service STP information, and Table: Output fields: STP describes the output fields.
Sample output*A:7210-SAS>show>service# id 200 stp
===============================================================================
Stp info, Service 200
===============================================================================
Bridge Id : 80:00.00:25:ba:08:f6:20 Top. Change Count : 0
Root Bridge : N/A Stp Oper State : Down
Primary Bridge : N/A Topology Change : Inactive
Mode : Rstp Last Top. Change : 0d 00:00:00
Vcp Active Prot. : N/A
Root Port : N/A External RPC : 0
===============================================================================
Stp port info
===============================================================================
Sap/Sdp Id Oper- Port- Port- Port- Oper- Link- Active
State Role State Num Edge Type Prot.
-------------------------------------------------------------------------------
Backbone VPLS Up N/A Forward 2048 N/A N/A N/A
1/1/15:200 Up N/A Forward 2049 N/A Pt-pt N/A
===============================================================================
*A:7210-SAS>show>service#
|
Label |
Description |
|---|---|
|
Bridge Id |
Specifies the MAC address used to identify this bridge in the network. |
|
Top. Change Count |
Specifies the total number of topology changes detected by the Spanning Tree Protocol instance associated with this service since the management Entity was last reset or initialized. |
|
Root Bridge |
Specifies the bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol instance associated with this service. This value is used as the Root Identifier parameter in all Configuration BPDUs originated by this node. |
|
Stp Oper State |
Displays the operational state of the STP |
|
Primary Bridge |
Specifies the bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol instance associated with this service. This value is used as the Root Identifier parameter in all Configuration BPDUs originated by this node. |
|
Topology Change |
Specifies whether a topology change is currently in progress. |
|
Mode |
Displays the mode of the STP |
|
Last Top. Change |
Specifies the time (in hundredths of a second) since the last time a topology change was detected by the Spanning Tree Protocol instance associated with this service. |
|
Root Port |
Specifies the port number of the port which provides the lowest cost path from this bridge to the root bridge. |
|
Backbone VPLS |
Displays the ID of the B-VPLS |
isid-using [ISID]
show>service
7210 SAS-T (network operating mode)
This command displays information about services using ISID.
Displays the service using the specified I-component Service ID (ISID).
The following output is an example of information about services using ISID, and Table: Output fields: ISID-using describes the output fields.
Sample output*A:7210-SAS>show>service# isid-using
===================================================================
Services
===================================================================
SvcId ISID Type b-Vpls Adm Opr SvcMtu CustId
-------------------------------------------------------------------
100 100 i-VPLS 1 Up Up 1514 1
200 200 i-VPLS 2 Up Up 1514 1
1000 1000 Epipe 2 Up Up 1514 1
3000 3000 Epipe 1 Up Up 1514 1
-------------------------------------------------------------------
Matching Services : 4
-------------------------------------------------------------------
===================================================================
*A:7210-SAS>show>service#
|
Label |
Description |
|---|---|
|
SvcId |
The service identifier. |
|
ISID |
Displays the ISID number. |
|
Type |
Indicates the type of service. |
|
b-Vpls |
Displays the B-VPLS ID. |
|
Adm |
Specifies the operating status of the service. |
|
Opr |
The current status of the service. |
|
SvcMtu |
Indicates the service MTU value. |
|
CustId |
Displays the customer ID. |
i-vpls
show>service>id
7210 SAS-T (network operating mode)
This command displays I-VPLS services associated with the B-VPLS service. This command only applies when the service is a B-VPLS.
The following output is an example of I-VPLS information, and Table: Output fields: I-VPLS describes the output fields.
Sample output*A:7210-SAS>show>service# id 2 i-vpls
===============================================================================
Related i-Vpls services for b-Vpls service 2
===============================================================================
i-Vpls SvcId Oper ISID Admin Oper
-------------------------------------------------------------------------------
200 200 Up Up
-------------------------------------------------------------------------------
Number of Entries : 1
-------------------------------------------------------------------------------
===============================================================================
*A:7210-SAS>show>service#
|
Label |
Description |
|---|---|
|
i-Vpls SvcId |
Displays the service ID of the I-VPLS service. |
|
Oper ISID |
Displays the ISID number. |
|
Admin |
Specifies the operating status of the service. |
|
Oper |
The current status of the service. |
epipe
show>service>id
7210 SAS-T (network operating mode)
This command displays Epipe information for the PBB service.
The following output is an example of Epipe information for a PBB service, and Table: Output fields: service ID Epipe describes the output fields.
Sample output*A:7210-SAS>show>service# id 2 epipe
===============================================================================
Related Epipe services for b-Vpls service 2
===============================================================================
Epipe SvcId Oper ISID Admin Oper
-------------------------------------------------------------------------------
1000 1000 Up Up
-------------------------------------------------------------------------------
Number of Entries : 1
-------------------------------------------------------------------------------
===============================================================================
*A:7210-SAS>show>service# id 200 epipe
|
Label |
Description |
|---|---|
|
Epipe SvcId |
Displays the service ID of the Epipe service bound to the B-VPLS service. |
|
Oper ISID |
Displays the ISID number. |
|
Admin |
Specifies the operating status of the service. |
|
Oper |
The current status of the service. |
isid-using [ISID]
show>service
7210 SAS-T (network operating mode)
This command displays the services using ISID.
Displays the service using the specified I-component Service ID (ISID).
The following output is an example of information about services using ISID, and Table: Output fields: ISID-using describes the output fields.
Sample output*A:7210-SAS>show>service# isid-using
===================================================================
Services
===================================================================
SvcId ISID Type b-Vpls Adm Opr SvcMtu CustId
-------------------------------------------------------------------
100 100 i-VPLS 1 Up Up 1514 1
200 200 i-VPLS 2 Up Up 1514 1
1000 1000 Epipe 2 Up Up 1514 1
3000 3000 Epipe 1 Up Up 1514 1
-------------------------------------------------------------------
Matching Services : 4
-------------------------------------------------------------------
===================================================================
*A:7210-SAS>show>service#
|
Label |
Description |
|---|---|
|
SvcId |
The service identifier. |
|
ISID |
Displays the ISID number. |
|
Type |
Indicates the type of service. |
|
b-Vpls |
Displays the B-VPLS ID. |
|
Admin |
Specifies the operating status of the service. |
|
Oper |
The current status of the service. |
|
SvcMtu |
Indicates the service MTU value. |
|
Customer Id |
Displays the customer ID. |
service-using [b-vpls] [i-vpls]
show>service
7210 SAS-T (network operating mode)
This command displays the services matching certain usage properties. If no optional parameters are specified, all services defined on the system are displayed.
Displays matching Epipe services.
Displays matching VPLS instances.
The following output is an example of service information, and Table: Output fields: Service-using describes the output fields.
Sample output*A:7210-SAS>show>service# service-using b-vpls
===============================================================================
Services [bvpls]
===============================================================================
ServiceId Type Adm Opr CustomerId Last Mgmt Change
-------------------------------------------------------------------------------
1 b-VPLS Up Up 1 04/04/2001 23:22:12
2 b-VPLS Up Up 1 04/04/2001 22:13:57
-------------------------------------------------------------------------------
Matching Services : 2
-------------------------------------------------------------------------------
===============================================================================
*A:7210-SAS>show>service#
|
Label |
Description |
|---|---|
|
Service Id |
The service identifier. |
|
Type |
Indicates the type of service. |
|
Admin |
Specifies the operating status of the service. |
|
Oper |
The current status of the service. |
|
Customer Id |
Displays the customer ID. |
|
Last Mgmt Change |
The date and time of the most recent management-initiated change to this customer. |
mac-name [detail]
show>service>pbb
7210 SAS-T (network operating mode)
This command displays information about a specific MAC name.
Displays detail information.
The following output is an example of information for a specific MAC name, and Table: Output fields: MAC name describes the output fields.
Sample output*A:7210-SAS>show>service# pbb mac-name test detail
=====================================================================
Services Using MAC name='test' addr='00:25:ba:08:f6:23'
=====================================================================
Svc-Id ISID
---------------------------------------------------------------------
No Matching Entries
=====================================================================
*A:7210-SAS>show>service#
|
Label |
Description |
|---|---|
|
Svc-Id |
The service identifier. |
|
ISID |
Displays the ISID number. |
|
Name |
Displays the MAC name. |
|
Addr |
Displays the MAC address |