The following command outputs are examples only; actual displays may differ depending on supported functionality and user configuration.
detail
show>router>pcep>pcc
7210 SAS-Mxp, 7210 SAS-R6, 7210 SAS-R12
This command displays detailed information about PCEP PCC.
The following output is an example of PCEP PCC more information, and Table: Output fields: PCEP PCC describes the output fields.
Sample output*A:ZBG>show>router>pcep# pcc detail
===============================================================================
Path Computation Element Protocol (PCEP) Path Computation Client (PCC) Info
===============================================================================
Admin Status : Down Oper Status : Down
Unknown Msg Limit : 10 msg/min
Keepalive Interval : 50 seconds DeadTimer Interval : 150 seconds
Capabilities List : stateful-delegate stateful-pce rsvp-path
Address : 10.10.10.10
Report Path Constraints: True
Open Wait Timer : 60 seconds Keep Wait Timer : 60 seconds
Sync Timer : 60 seconds Request Timer : 120 seconds
Connection Timer : 60 seconds Allow Negotiations : False
Max Sessions : 1 Max Unknown Req : 1000
===============================================================================
*A:ZBG>show>router>pcep#
|
Label |
Description |
|---|---|
|
Admin Status |
Displays the administrative status of the PCC |
|
Oper Status |
Displays the operational status of the PCC |
|
Unknown Msg Limit |
Displays the maximum rate of unknown messages that can be received on a PCEP session |
|
Keepalive Interval |
Displays the specified keepalive interval for the PCEP session |
|
DeadTimer Interval |
Displays the specified dead time interval for the PCEP session |
|
Capabilities List |
Displays the capabilities list for the PCEP session |
|
Address |
Displays the local IP address of the PCEP speaker |
|
Report Path Constraints |
Displays whether to include LSP path constraints in the PCE report messages sent from the PCC to a PCE |
|
Open Wait Timer |
Displays the value of the open wait timer for the PCEP session |
|
Keep Wait Timer |
Displays the value of the keep wait timer for the PCEP session |
|
Sync Timer |
Displays the value of the synchronization timer for the PCEP session |
|
Request Timer |
Displays the value of the request timer for the PCEP session |
|
Connection Timer |
Displays the value of the keep wait timer for the PCEP session |
|
Allow Negotiations |
Displays where negotiations between PCEP PCC and PCE are allowed |
|
Max Sessions |
Displays the maximum number of PCEP sessions on the router |
|
Max Unknown Req |
Displays the maximum number of unknown requests for PCEP sessions on the router |
lsp-db [lsp-type lsp_type] [delegated-pce ip-address]
lsp-db [lsp-type lsp_type] from ip-address [delegated-pce ip-address]
lsp-db [lsp-type lsp_type] lsp lsp-name [delegated-pce ip-address]
lsp-db [lsp-type lsp_type] to ip-address [tunnel-id [tunnel-id]]
lsp-db [lsp-type lsp_type] tunnel-id [tunnel-id]
show>router>pcep>pcc
7210 SAS-Mxp, 7210 SAS-R6, 7210 SAS-R12
This command displays PCEP PCC LSP information.
Specifies the type of LSP to display. The only available option is RSVP-TE point-to-point LSPs (rsvp-p2p).
Specifies a tunnel ID.
Specifies an IPv4 address.
The following output is an example of PCEP PCC LSP information, and Table: Output fields: LSP describes the output fields.
Sample output*A:ZBG# show router pcep pcc lsp-db
===============================================================================
PCEP Path Computation Client (PCC) LSP Update Info
===============================================================================
PCEP-specific LSP ID: 1
LSP ID : 21504 LSP Type : rsvp-p2p
Tunnel ID : 1 Extended Tunnel Id : 10.20.1.3
LSP Name : test_lsp::fully_loose
Source Address : 10.20.1.3 Destination Address : 10.20.1.1
LSP Delegated : True Delegate PCE Address: 138.120.210.36
Oper Status : active
-------------------------------------------------------------------------------
PCEP-specific LSP ID: 2
LSP ID : 21510 LSP Type : rsvp-p2p
Tunnel ID : 1 Extended Tunnel Id : 10.20.1.3
LSP Name : test_lsp::stdby_fully_loose_2
Source Address : 10.20.1.3 Destination Address : 10.20.1.1
LSP Delegated : True Delegate PCE Address: 10.120.210.36
Oper Status : up
===============================================================================
*A:ZBG#
Label |
Description |
|---|---|
PCEP-specific LSP ID |
Displays the PCEP-specific LSP identifier |
LSP ID |
Displays the LSP identifier |
Tunnel ID |
Displays the tunnel identifier for the LSP |
LSP Name |
Displays the configured LSP name |
Source Address |
Displays the source IP address of the LSP |
LSP Delegated |
Displays the delegation status of the LSP |
Oper Status |
Displays the operational status of the LSP |
LSP Type |
Displays the type of the LSP |
Extended Tunnel ID |
Displays the expanded tunnel identifier for the LSP |
Destination Address |
Displays the destination IP address of the LSP |
Delegate PCE Address |
Displays the IP address of the delegate PCE router |
path-request [lsp-type {rsvp-p2p}] [dest ip-address] [detail]
show>router>pcep>pcc
7210 SAS-Mxp, 7210 SAS-R6, 7210 SAS-R12
This command displays PCEP PCC path request information.
Specifies the type of LSP to display. The only available option is RSVP-TE point-to-point LSPs.
Specifies the destination IPv4 address to display.
Keyword to display detailed path request information.
The following output is an example of PCEP PCC path request information, and Table: Output fields: Path request describes the output fields.
Sample output*A:ZBG# show router pcep pcc path-request
===============================================================================
PCEP Path Computation Client (PCC) Path Computation Request (PCReq) Info
===============================================================================
Request ID : 4 Message State : sent-for-compute
Tunnel ID : 2 Extended Tunnel Id : 10.20.1.3
LSP ID : 62468 LSP Type : rsvp-p2p
LSP Name : test_lsp::fully_loose
Source Address : 10.20.1.3 Destination Address: 10.20.1.1
SVEC Id : 4 LSP Bandwidth : 0
===============================================================================
*A:ZBG#
Label |
Description |
|---|---|
Request ID |
Displays the PCEP PCC path request identifier |
Tunnel ID |
Displays the tunnel identifier for the LSP |
LSP ID |
Displays the LSP identifier |
LSP Name |
Displays the configured LSP name |
Source Address |
Displays the source IP address of the LSP |
SVEC Id |
Displays the synchronization vector identifier |
Message State |
Displays the current state of the request |
Extended Tunnel Id |
Displays the expanded tunnel identifier for the LSP |
LSP Type |
Displays the type of the LSP |
Destination Address |
Displays the destination IP address of the LSP |
LSP Bandwidth |
Displays the bandwidth of the LSP |
peer [ip-address] [detail]
show>router>pcep>pcc
7210 SAS-Mxp, 7210 SAS-R6, 7210 SAS-R12
This command displays PCEP PCC peer information.
Specifies a peer IPv4 address to display.
Keyword to display detailed peer information.
The following output is an example of a PCEP PCC peer information, and Table: Output fields: PCC peer describes the output fields.
Sample output*A:ZBG>show>router>pcep>pcc# peer detail
===============================================================================
PCEP Path Computation Client (PCC) Peer Info
===============================================================================
IP Address : 10.10.10.11
Admin Status : Down Oper Status : Down
Peer Capabilities : (Not Specified)
Speaker ID : (Undefined)
Sync State : not-initialized Peer Overloaded : False
Session Establish Time: 0d 00:00:00
Oper Keepalive : N/A Oper DeadTimer : N/A
Session Setup Count : 0 Session Setup Fail Count: 0
-------------------------------------------------------------------------------
Statistics Information
-------------------------------------------------------------------------------
Sent Received
-------------------------------------------------------------------------------
PC Request Message 0 0
PC Reply Message 0 0
PC Error Message 0 0
PC Notification Message 0 0
PC Keepalive Message 0 0
PC Update Message 0 0
PC Report Message 0 0
Path Report 0 0
Path Request 0 0
-------------------------------------------------------------------------------
===============================================================================
*A:ZBG>show>router>pcep>pcc#
Label |
Description |
|---|---|
IP Address |
Displays the IP address of the PCC peer |
Admin Status |
Displays the administrative status of the PCC peer |
Oper Status |
Displays the operational status of the PCC peer |
Peer Capabilities |
Displays the PCEP capabilities of the PCC peer |
Speaker ID |
Displays the IP address of the PCC peer speaker |
Sync State |
Displays the synchronization state of the PCC peer speaker |
Peer Overloaded |
Displays whether the PCC peer is overloaded |
Session Establish Time |
Displays the length of time since the PCEP session was established |
Oper Keepalive |
Displays the operational value for the PCC peer keepalive timer |
Oper DeadTimer |
Displays the operational value for the PCC peer dead timer |
Session Setup Count |
Displays the number of times that the PCEP session has been set up |
Session Setup Fail Count |
Displays the number of times that the PCEP session failed to be set up |
Statistics Information |
|
PC Request Message |
Displays the number of path computation (PC) request messages sent the PCC peer and received from the PCC peer |
PC Reply Message |
Displays the number of PC reply messages sent to the PCC peer and received from the PCC peer |
PC Error Message |
Displays the number of PC error messages sent to the PCC peer and received from the PCC peer |
PC Notification Message |
Displays the number of PC notification messages sent to the PCC peer and received from the PCC peer |
PC Keepalive Message |
Displays the number of PC keepalive messages sent to the PCC peer and received from the PCC peer |
PC Update Message |
Displays the number of PC update messages sent to the PCC peer and received from the PCC peer |
PC Report Message |
Displays the number of PC report messages sent to the PCC peer and received from the PCC peer |
Path Report |
Displays the number of path reports sent to the PCC peer and received from the PCC peer |
Path Request |
Displays the path requests sent to the PCC peer and received from the PCC peer |
status
show>router>pcep>pcc
7210 SAS-Mxp, 7210 SAS-R6, 7210 SAS-R12
This command displays PCEP PCC status information.
The following output is an example of a PCEP PCC status information, and Table: Output fields: PCC status describes the output fields.
Sample output*A:ZBG>show>router>pcep>pcc# status
===============================================================================
Path Computation Element Protocol (PCEP) Path Computation Client (PCC) Info
===============================================================================
Admin Status : Down Oper Status : Down
Unknown Msg Limit : 10 msg/min
Keepalive Interval : 50 seconds DeadTimer Interval : 150 seconds
Capabilities List : stateful-delegate stateful-pce rsvp-path
Address : 10.10.10.10
Report Path Constraints: True
-------------------------------------------------------------------------------
PCEP Path Computation Client (PCC) Peer Info
-------------------------------------------------------------------------------
Peer Admin State/Oper State Oper Keepalive/Oper DeadTimer
-------------------------------------------------------------------------------
10.10.10.11 Down/Down Not-Applicable/Not-Applicable
-------------------------------------------------------------------------------
===============================================================================
*A:ZBG>show>router>pcep>pcc#
Label |
Description |
|---|---|
Admin Status |
Displays the administrative status of the PCC |
Oper Status |
Displays the operational status of the PCC |
Unknown Msg Limit |
Displays the maximum rate of unknown messages that can be received on a PCEP session |
Keepalive Interval |
Displays the specified keepalive interval for the PCEP session |
DeadTimer Interval |
Displays the specified dead time interval for the PCEP session |
Capabilities List |
Displays the capabilities list for the PCEP session |
Address |
Displays the local IP address of the PCEP speaker |
Report Path Constraints |
Displays whether to include LSP path constraints in the PCE report messages sent from the PCC to a PCE |
PCEP Path Computation Client (PCC) Peer Info |
|
Peer |
Displays the IP address of the PCC peer |
Admin State/Oper State |
Displays the administrative and operational states of the PCC peer |
Oper Keepalive/Oper DeadTimer |
Displays the operational keepalive and dead timer intervals of the PCC peer |