bindings active [fec-type prefixes] [prefix ip-prefix/mask] [egress-nh ip-address | egress-if port-id | egress-lsp tunnel-id] [summary]
bindings active active-ecmp
bindings active [fec-type p2mp] [p2mp-id identifier root ip-address] [egress-nh ip-address | egress-if port-id | egress-lsp tunnel-id] [summary]
bindings active [fec-type p2mp] [source ip-address] group mcast-address root ip-address]] [egress-nh ip-address] | egress-if port-id | egress-lsp tunnel-id] [summary]
bindings active prefixes [family] [{summary | detail}] [egress-if port-id]
bindings active prefixes [family] [{summary | detail}] [egress-lsp tunnel-id]
bindings active prefixes [egress-nh ip-address] [family] [{summary | detail}]
bindings prefix ip-prefix/ip-prefix-length [{summary | detail}] [egress-if port-id]
bindings prefix ip-prefix/ip-prefix-length [{summary | detail}] [egress-lsp tunnel-id]
bindings prefix ip-prefix/ip-prefix-length [egress-nh ip-address] [{summary | detail}]
bindings fec-type {prefixes|services} [session ip-addr 4c5]] [summary| detail]
bindings fec-type p2mp [session ip-addr[:label-space]] [summary|detail]
bindings fec-type p2mp p2mp-id identifier root ip-address [session ip-addr[:label-space]] [summary|detail]
bindings p2mp-id identifier root ip-address [detail]
bindings fec-type p2mp root ip-address [session ip-addr[:label-space]] [summary|detail] source ip-address group mcast-address
bindings [fec-type fec-type [detail]] [session ip-addr[:label-space]]
bindings label-type start-label [end-label]
bindings {prefix ip-prefix/mask [detail]} [session ip-addr[:label-space]]
bindings prefixes prefix ip-prefix/ip-prefix-length [{summary | detail}] [session ip-addr[:label-space]]
bindings prefixes [family] [{summary | detail}] [session ip-addr[:label-space]]
bindings active [prefix ip-prefix/mask]
bindings service-id service-id [detail]
bindings vc-type vc-type [{vc-id vc-id | agi agi} [session ip-addr[:lab el-space]]
show>router>ldp
Supported on all 7210 SAS platforms as described in this document.
This command displays the contents of the label information base.
Specifies the family type.
Specify the kind of FEC that the label mapping, withdraw, release and request messages are referring to.
Displays information in a summarized format.
Displays detailed information.
Displays the LDP active bindings with ECMP routes that have been successfully installed in the hardware FIB.
Displays configuration information about LDP sessions.
Specify information for the specified IP prefix and mask length. Host bits must be 0.
Specifies the length of the IP prefix.
Specifies the label space identifier that the router is advertising on the interface.
Specifies the 32-bit address mask used to indicate the bits of an IP address that are being used for the subnet address.
Specifies the port ID.
Specifies the tunnel ID.
Specifies the egress IP address.
Specifies a label value to begin the display.
Specifies a label value to end the display.
Specifies the VC type to display.
Specifies the VC ID to display.
Displays the P2MP group multicast address bindings.
Displays LDP active P2MP identifier bindings.
Specifies the service ID number to display.
The following outputs are examples of LDP bindings information, and Table: Output fields: LDP bindings describes the output fields.
Sample outputA:7210SAS# show router ldp bindings
===============================================================================
LDP LSR ID: 2.2.2.2
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
S - Status Signaled Up, D - Status Signaled Down
E - Epipe Service, V - VPLS Service, M - Mirror Service
A - Apipe Service, F - Fpipe Service, I - IES Service, R - VPRN service
P - Ipipe Service, WP - Label Withdraw Pending
BU - Alternate Next-hop for Fast Re-Route, TLV - (Type, Length: Value)
===============================================================================
LDP Prefix Bindings
===============================================================================
Prefix IngLbl EgrLbl EgrIntf/ EgrNextHop
Peer LspId
-------------------------------------------------------------------------------
10.1.1.1/32 -- 262143 1/1/3:12 10.11.12.1
1.1.1.1
10.1.1.1/32 131069U 131069 -- --
6.6.6.6
10.2.2.2/32 131071U -- -- --
1.1.1.1
10.2.2.2/32 131071U -- -- --
6.6.6.6
..........
10.6.6.6/32 -- 131071 1/1/9:26 10.11.26.6
6.6.6.6
-------------------------------------------------------------------------------
No. of Prefix Bindings: 10
===============================================================================
===============================================================================
LDP Generic P2MP Bindings
===============================================================================
P2MP-Id RootAddr
Interface Peer IngLbl EgrLbl EgrIntf/ EgrNextHop
LspId
-------------------------------------------------------------------------------
8193 10.1.1.1
73732 1.1.1.1 131065U -- -- --
8193 10.2.2.2
73728 1.1.1.1 -- 262139 1/1/3:12 10.11.12.1
88194 10.6.6.6
73738 6.6.6.6 131054U -- -- --
8195 10.6.6.6
73739 6.6.6.6 131053U -- -- --
-------------------------------------------------------------------------------
No. of Generic P2MP Bindings: 13
===============================================================================
===============================================================================
LDP In-Band-SSM P2MP Bindings
===============================================================================
Source
Group
Interface RootAddr
Peer IngLbl EgrLbl EgrIntf/ EgrNextHop
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
===============================================================================
LDP Service FEC 128 Bindings
===============================================================================
Type VCId SvcId SDPId Peer IngLbl EgrLbl LMTU RMTU
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
===============================================================================
LDP Service FEC 129 Bindings
===============================================================================
AGI SAII
TAII
Type SvcId SDPId Peer IngLbl EgrLbl LMTU RMTU
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
A:7210SAS#
A:7210SAS# show router ldp bindings detail
===============================================================================
LDP P2MP Bindings
===============================================================================
-------------------------------------------------------------------------------
P2MP Type : 1 P2MP-Id : 100
-------------------------------------------------------------------------------
Ing Lbl : 131065 Peer : 10.20.1.1
Egr Lbl : 131069 Peer : 10.20.1.2
Egr Int/LspId : 1/1/2 EgrNextHop : 10.10.2.2
Egr. Flags : None Ing. Flags : None
Egr Lbl : 131067 Peer : 10.20.1.3
Egr Int/LspId : 1/1/3 EgrNextHop : 10.10.3.2
Egr. Flags : None Ing. Flags : None
Egr Lbl : 131064 Peer : 10.20.1.4
Egr Int/LspId : 1/1/3 EgrNextHop : 10.10.4.2
Egr. Flags : None Ing. Flags : None
-------------------------------------------------------------------------------
P2MP Type : 1 P2MP-Id : 200
-------------------------------------------------------------------------------
Ing Lbl : 131066 Peer : 10.20.1.1
Egr Lbl : 131063 Peer : 10.20.1.2
Egr Int/LspId : 1/1/2 EgrNextHop : 10.10.2.2
Egr. Flags : None Ing. Flags : None
Egr Lbl : 131068 Peer : 10.20.1.3
Egr Int/LspId : 1/1/3 EgrNextHop : 10.10.3.2
Egr. Flags : None Ing. Flags : None
===============================================================================
A:7210SAS#
A:7210SAS# show router ldp bindings p2mp-id 8193 root 10.2.2.2 detail
===============================================================================
LDP LSR ID: 10.2.2.2
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate Next-hop for Fast Re-Route
===============================================================================
LDP Generic P2MP Bindings
===============================================================================
-------------------------------------------------------------------------------
P2MP Type : 1 P2MP-Id : 8193
Root-Addr : 10.2.2.2
-------------------------------------------------------------------------------
Ing Lbl : -- Peer : 1.1.1.1
Egr Lbl : 262139
Egr Int/LspId : 1/1/3:12
EgrNextHop : 10.11.12.1
Egr. Flags : None Ing. Flags : None
Metric : 1 Mtu : 1560
-------------------------------------------------------------------------------
P2MP Type : 1 P2MP-Id : 8193
Root-Addr : 10.2.2.2
-------------------------------------------------------------------------------
Ing Lbl : -- Peer : 6.6.6.6
Egr Lbl : 131059
Egr Int/LspId : 1/1/9:26
EgrNextHop : 10.11.26.6
Egr. Flags : None Ing. Flags : None
Metric : 1 Mtu : 1560
===============================================================================
No. of Generic P2MP Bindings: 2
===============================================================================
A:7210SAS#
A:7210SAS# show router ldp bindings active fec-type p2mp
===============================================================================
LDP Generic P2MP Bindings (Active)
===============================================================================
P2MP-Id RootAddr
Interface Op IngLbl EgrLbl EgrIntf/ EgrNextHop
LspId
-------------------------------------------------------------------------------
8193 10.1.1.1
73731 Pop 131064 -- -- --
8193 10.1.1.1
7
8195 10.6.6.6
73738 Pop 131058 -- -- --
-------------------------------------------------------------------------------
No. of Generic P2MP Active Bindings: 15
===============================================================================
===============================================================================
LDP In-Band-SSM P2MP Bindings (Active)
===============================================================================
Source
Group
Interface RootAddr
Op IngLbl EgrLbl EgrIntf/ EgrNextHop
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
A:7210SAS#
A:7210SAS# show router ldp bindings fec-type p2mp detail
===============================================================================
LDP LSR ID: 2.2.2.2
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate Next-hop for Fast Re-Route
===============================================================================
LDP Generic P2MP Bindings
===============================================================================
-------------------------------------------------------------------------------
P2MP Type : 1 P2MP-Id : 8193
Root-Addr : 10.1.1.1
-------------------------------------------------------------------------------
Ing Lbl : 131053U Peer : 6.6.6.6
Egr Lbl : --
Egr Int/LspId : --
EgrNextHop : --
Egr. Flags : None Ing. Flags : None
===============================================================================
No. of Generic P2MP Bindings: 13
===============================================================================
===============================================================================
LDP In-Band-SSM P2MP Bindings
===============================================================================
No Matching Entries Found
===============================================================================
A:7210SAS#
A:7210SAS# show router ldp bindings p2mp-id 8193 root 10.2.2.2 detail
===============================================================================
LDP LSR ID: 10.2.2.2
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate Next-hop for Fast Re-Route
===============================================================================
LDP Generic P2MP Bindings
===============================================================================
-------------------------------------------------------------------------------
P2MP Type : 1 P2MP-Id : 8193
Root-Addr : 10.2.2.2
-------------------------------------------------------------------------------
Ing Lbl : -- Peer : 1.1.1.1
Egr Lbl : 262139
Egr Int/LspId : 1/1/3:12
EgrNextHop : 10.11.12.1
Egr. Flags : None Ing. Flags : None
Metric : 1 Mtu : 1560
-------------------------------------------------------------------------------
P2MP Type : 1 P2MP-Id : 8193
Root-Addr : 10.2.2.2
-------------------------------------------------------------------------------
Ing Lbl : -- Peer : 6.6.6.6
Egr Lbl : 131059
Egr Int/LspId : 1/1/9:26
EgrNextHop : 10.11.26.6
Egr. Flags : None Ing. Flags : None
Metric : 1 Mtu : 1560
===============================================================================
No. of Generic P2MP Bindings: 2
===============================================================================
A:7210SAS#
The following outputs pertain to unicast FEC resolved over an unnumbered interface.
A:7210SAS# # show router ldp bindings active
===============================================================================
Legend: (S) - Static (M) - Multi-homed Secondary Support
(B) - BGP Next Hop (BU) - Alternate Next-hop for Fast Re-Route
===============================================================================
LDP Prefix Bindings (Active)
===============================================================================
Prefix Op IngLbl EgrLbl EgrIntf/LspId EgrNextHop
-------------------------------------------------------------------------------
10.20.1.1/32 Push -- 262143 1/1/1 Unnumbered
10.20.1.1/32 Swap 262138 262143 1/1/1 Unnumbered
10.20.1.2/32 Push -- 262143 lag-1 Unnumbered
10.20.1.2/32 Swap 262139 262143 lag-1 Unnumbered
10.20.1.3/32 Pop 262143 -- -- --
10.20.1.4/32 Push -- 262143 2/1/2 Unnumbered
10.20.1.4/32 Swap 262142 262143 2/1/2 Unnumbered
10.20.1.5/32 Push -- 262143 2/1/1 Unnumbered
10.20.1.5/32 Swap 262141 262143 2/1/1 Unnumbered
10.20.1.6/32 Push -- 262140 2/1/2 Unnumbered
10.20.1.6/32 Swap 262140 262140 2/1/2 Unnumbered
-------------------------------------------------------------------------------
No. of Prefix Active Bindings: 11
===============================================================================
A:7210SAS#
A:7210SAS# show router ldp bindings
===============================================================================
LDP LSR ID: 10.20.1.3
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
S - Status Signaled Up, D - Status Signaled Down
E - Epipe Service, V - VPLS Service, M - Mirror Service
A - Apipe Service, F - Fpipe Service, I - IES Service, R - VPRN service
P - Ipipe Service, WP - Label Withdraw Pending, C - Cpipe Service
BU - Alternate For Fast Re-Route, TLV - (Type, Length: Value)
===============================================================================
LDP Prefix Bindings
===============================================================================
Prefix IngLbl EgrLbl EgrIntf/ EgrNextHop
Peer LspId
-------------------------------------------------------------------------------
10.20.1.1/32 -- 262143 1/1/1 Unnumbered
10.20.1.1
10.20.1.1/32 262138U 262142 -- --
10.20.1.2
10.20.1.1/32 262138U 262138 -- --
10.20.1.4
10.20.1.1/32 262138U 262138 -- --
10.20.1.5
10.20.1.2/32 262139U 262142 -- --
10.20.1.1
10.20.1.2/32 -- 262143 lag-1 Unnumbered
10.20.1.2
10.20.1.2/32 262139U 262139 -- --
10.20.1.4
10.20.1.2/32 262139U 262139 -- --
10.20.1.5
10.20.1.3/32 262143U -- -- --
10.20.1.1
10.20.1.3/32 262143U -- -- --
10.20.1.2
10.20.1.3/32 262143U -- -- --
10.20.1.4
10.20.1.3/32 262143U -- -- --
10.20.1.5
10.20.1.4/32 262142U 262141 -- --
10.20.1.1
10.20.1.4/32 262142U 262141 -- --
10.20.1.2
10.20.1.4/32 -- 262143 2/1/2 Unnumbered
10.20.1.4
10.20.1.4/32 262142U 262141 -- --
10.20.1.5
10.20.1.5/32 262141U 262138 -- --
10.20.1.1
10.20.1.5/32 262141U 262139 -- --
10.20.1.2
10.20.1.5/32 262141U 262141 -- --
10.20.1.4
10.20.1.5/32 -- 262143 2/1/1 Unnumbered
10.20.1.5
10.20.1.6/32 262140U 262140 -- --
10.20.1.1
10.20.1.6/32 262140U 262138 -- --
10.20.1.2
10.20.1.6/32 262140N 262140 2/1/2 Unnumbered
10.20.1.4
10.20.1.6/32 262140U 262140 -- --
10.20.1.5
-------------------------------------------------------------------------------
No. of Prefix Bindings: 24
===============================================================================
A:7210SAS#
A:7210SAS# show router ldp bindings detail
===============================================================================
LDP LSR ID: 10.20.1.3
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
S - Status Signaled Up, D - Status Signaled Down
E - Epipe Service, V - VPLS Service, M - Mirror Service
A - Apipe Service, F - Fpipe Service, I - IES Service, R - VPRN service
P - Ipipe Service, WP - Label Withdraw Pending, C - Cpipe Service
BU - Alternate For Fast Re-Route, TLV - (Type, Length: Value)
===============================================================================
LDP Prefix Bindings
===============================================================================
-------------------------------------------------------------------------------
Prefix : 10.20.1.1/32
-------------------------------------------------------------------------------
Ing Lbl : -- Peer : 10.20.1.1
Egr Lbl : 262143
Egr Int/LspId : 1/1/1
EgrNextHop : Unnumbered
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.10.2.3
Metric : 1000 Mtu : 1500
-------------------------------------------------------------------------------
Prefix : 10.20.1.1/32
-------------------------------------------------------------------------------
Ing Lbl : 262138U Peer : 10.20.1.2
Egr Lbl : 262142
Egr Int/LspId : --
EgrNextHop : --
Egr. Flags : None Ing. Flags : None
Egr If Name : n/a
-------------------------------------------------------------------------------
Prefix : 10.20.1.1/32
-------------------------------------------------------------------------------
Ing Lbl : 262138U Peer : 10.20.1.4
Egr Lbl : 262138
Egr Int/LspId : --
EgrNextHop : --
Egr. Flags : None Ing. Flags : None
Egr If Name : n/a
-------------------------------------------------------------------------------
Prefix : 10.20.1.1/32
-------------------------------------------------------------------------------
Ing Lbl : 262138U Peer : 10.20.1.5
Egr Lbl : 262138
Egr Int/LspId : --
EgrNextHop : --
Egr. Flags : None Ing. Flags : None
Egr If Name : n/a
-------------------------------------------------------------------------------
Prefix : 10.20.1.2/32
-------------------------------------------------------------------------------
Ing Lbl : 262139U Peer : 10.20.1.1
Egr Lbl : 262142
Egr Int/LspId : --
EgrNextHop : --
Egr. Flags : None Ing. Flags : None
Egr If Name : n/a
-------------------------------------------------------------------------------
A:7210SAS# show router ldp session local-addresses
===============================================================================
LDP Session Local-Addresses
===============================================================================
-------------------------------------------------------------------------------
Session with Peer 10.20.1.2:0, Local 10.20.1.3:0
-------------------------------------------------------------------------------
Sent Addresses: 10.1.1.1 10.10.12.3 10.10.22.3 10.20.1.3
10.180.2.3 10.180.3.3 10.180.5.3 10.180.11.3
10.181.2.3 10.181.3.3 10.181.5.3 10.181.11.3
10.182.2.3 10.182.3.3 10.182.5.3 10.182.11.3
Recv Addresses: 10.2.2.2 10.10.12.2 10.20.1.2 10.180.1.2
10.180.3.2 10.180.4.2 10.181.1.2 10.181.3.2
10.181.4.2 10.182.1.2 10.182.3.2 10.182.4.2
-------------------------------------------------------------------------------
Session with Peer 10.20.1.4:0, Local 10.20.1.3:0
-------------------------------------------------------------------------------
Sent Addresses: 10.1.1.1 10.10.12.3 10.10.22.3 10.20.1.3
10.180.2.3 10.180.3.3 10.180.5.3 10.180.11.3
10.181.2.3 10.181.3.3 10.181.5.3 10.181.11.3
10.182.2.3 10.182.3.3 10.182.5.3 10.182.11.3
Recv Addresses: 10.10.22.4 10.20.1.4 10.180.4.4 10.180.6.4
10.180.9.4 10.180.11.4 10.181.4.4 10.181.6.4
10.181.9.4 10.181.11.4 10.182.4.4 10.182.6.4
10.182.9.4 10.182.11.4
-------------------------------------------------------------------------------
Session with Peer 10.20.1.5:0, Local 10.20.1.3:0
-------------------------------------------------------------------------------
Sent Addresses: 10.1.1.1 10.10.12.3 10.10.22.3 10.20.1.3
10.180.2.3 10.180.3.3 10.180.5.3 10.180.11.3
10.181.2.3 10.181.3.3 10.181.5.3 10.181.11.3
10.182.2.3 10.182.3.3 10.182.5.3 10.182.11.3
Recv Addresses: 10.20.1.5 10.180.5.5 10.180.6.5 10.180.10.5
10.181.5.5 10.181.6.5 10.181.10.5 10.182.5.5
10.182.6.5 10.182.10.5
===============================================================================
A:7210SAS#
The following outputs pertain to multicast P2MP FEC resolved over an unnumbered interface.
P2MP LSPs are only supported on 7210 SAS-Mxp, 7210 SAS-R6, 7210 SAS-R12, and 7210 SAS-T.
A:7210SAS# show router ldp bindings active fec-type p2mp
===============================================================================
LDP Generic P2MP Bindings (Active)
===============================================================================
P2MP-Id RootAddr
Interface Op IngLbl EgrLbl EgrIntf/ EgrNextHop
LspId
-------------------------------------------------------------------------------
1 10.20.1.3
73728 Push -- 262142 1/1/2:0 Unnumbered
1 10.20.1.3
73728 Push -- 262137 2/1/2:0 Unnumbered
2 10.20.1.3
73729 Push -- 262141 1/1/2:0 Unnumbered
2 10.20.1.3
73729 Push -- 262136 2/1/2:0 Unnumbered
3 10.20.1.3
73730 Push -- 262140 1/1/2:0 Unnumbered
3 10.20.1.3
73730 Push -- 262135 2/1/2:0 Unnumbered
4 10.20.1.3
73731 Push -- 262139 1/1/2:0 Unnumbered
4 10.20.1.3
73731 Push -- 262134 2/1/2:0 Unnumbered
===============================================================================
A:7210SAS#
A:7210SAS# show router ldp bindings fec-type p2m
===============================================================================
LDP LSR ID: 10.20.1.3
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
===============================================================================
LDP Generic P2MP Bindings
===============================================================================
P2MP-Id RootAddr
Interface Peer IngLbl EgrLbl EgrIntf/ EgrNextHop
LspId
-------------------------------------------------------------------------------
1 10.20.1.3
73728 10.20.1.2 -- 262142 1/1/2:0 Unnumbered
1 10.20.1.3
73728 10.20.1.4 -- 262137 2/1/2:0 Unnumbered
2 10.20.1.3
73729 10.20.1.2 -- 262141 1/1/2:0 Unnumbered
2 10.20.1.3
73729 10.20.1.4 -- 262136 2/1/2:0 Unnumbered
3 10.20.1.3
73730 10.20.1.2 -- 262140 1/1/2:0 Unnumbered
3 10.20.1.3
73730 10.20.1.4 -- 262135 2/1/2:0 Unnumbered
4 10.20.1.3
73731 10.20.1.2 -- 262139 1/1/2:0 Unnumbered
4 10.20.1.3
73731 10.20.1.4 -- 262134 2/1/2:0 Unnumbered
===============================================================================
A:7210SAS#
A:7210SAS# show router ldp bindings fec-type p2mp detail
===============================================================================
LDP LSR ID: 10.20.1.3
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
===============================================================================
LDP Generic P2MP Bindings
===============================================================================
-------------------------------------------------------------------------------
P2MP Type : 1 P2MP-Id : 1
Root-Addr : 10.20.1.3
-------------------------------------------------------------------------------
Ing Lbl : -- Peer : 10.20.1.2
Egr Lbl : 262142
Egr Int/LspId : 1/1/2:0
EgrNextHop : Unnumbered
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.180.3.3
Metric : 1 Mtu : 1496
-------------------------------------------------------------------------------
P2MP Type : 1 P2MP-Id : 1
Root-Addr : 10.20.1.3
-------------------------------------------------------------------------------
Ing Lbl : -- Peer : 10.20.1.4
Egr Lbl : 262137
Egr Int/LspId : 2/1/2:0
EgrNextHop : Unnumbered
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.180.11.3
Metric : 1 Mtu : 1496
-------------------------------------------------------------------------------
P2MP Type : 1 P2MP-Id : 2
Root-Addr : 10.20.1.3
-------------------------------------------------------------------------------
Ing Lbl : -- Peer : 10.20.1.2
Egr Lbl : 262141
Egr Int/LspId : 1/1/2:0
EgrNextHop : Unnumbered
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.180.3.3
Metric : 1 Mtu : 1496
-------------------------------------------------------------------------------
P2MP Type : 1 P2MP-Id : 2
Root-Addr : 10.20.1.3
-------------------------------------------------------------------------------
Ing Lbl : -- Peer : 10.20.1.4
Egr Lbl : 262136
Egr Int/LspId : 2/1/2:0
EgrNextHop : Unnumbered
Egr. Flags : None Ing. Flags : None
Egr If Name : ip-10.180.11.3
Metric : 1 Mtu : 1496
-------------------------------------------------------------------------------
A:7210SAS#
A:7210SAS# show router ldp session local-addresses
===============================================================================
LDP Session Local-Addresses
===============================================================================
-------------------------------------------------------------------------------
Session with Peer 10.20.1.2:0, Local 10.20.1.3:0
-------------------------------------------------------------------------------
Sent Addresses: 10.1.1.1 10.10.12.3 10.10.22.3 10.20.1.3
10.180.2.3 10.180.3.3 10.180.5.3 10.180.11.3
10.181.2.3 10.181.3.3 10.181.5.3 10.181.11.3
10.182.2.3 10.182.3.3 10.182.5.3 10.182.11.3
Recv Addresses: 10.2.2.2 10.10.12.2 10.20.1.2 10.180.1.2
10.180.3.2 10.180.4.2 10.181.1.2 10.181.3.2
10.181.4.2 10.182.1.2 10.182.3.2 10.182.4.2
-------------------------------------------------------------------------------
Session with Peer 10.20.1.4:0, Local 10.20.1.3:0
-------------------------------------------------------------------------------
Sent Addresses: 10.1.1.1 10.10.12.3 10.10.22.3 10.20.1.3
10.180.2.3 10.180.3.3 10.180.5.3 10.180.11.3
10.181.2.3 10.181.3.3 10.181.5.3 10.181.11.3
10.182.2.3 10.182.3.3 10.182.5.3 10.182.11.3
Recv Addresses: 10.10.22.4 10.20.1.4 10.180.4.4 10.180.6.4
10.180.9.4 10.180.11.4 10.181.4.4 10.181.6.4
10.181.9.4 10.181.11.4 10.182.4.4 10.182.6.4
10.182.9.4 10.182.11.4
-------------------------------------------------------------------------------
Session with Peer 10.20.1.5:0, Local 10.20.1.3:0
-------------------------------------------------------------------------------
Sent Addresses: 10.1.1.1 10.10.12.3 10.10.22.3 10.20.1.3
10.180.2.3 10.180.3.3 10.180.5.3 10.180.11.3
10.181.2.3 10.181.3.3 10.181.5.3 10.181.11.3
10.182.2.3 10.182.3.3 10.182.5.3 10.182.11.3
Recv Addresses: 10.20.1.5 10.180.5.5 10.180.6.5 10.180.10.5
10.181.5.5 10.181.6.5 10.181.10.5 10.182.5.5
10.182.6.5 10.182.10.5
===============================================================================
A:7210SAS#
Label |
Description |
|---|---|
|
Displays the LDP label switch router ID |
|
U: Label In Use N: Label Not In Use W: Label Withdrawn S: Status Signaled Up D: Status Signaled Down E: Epipe service V: VPLS service M: Mirror service A: Apipe service F: Fpipe service I: IES service R: VPRN service P: Ipipe service WP: Label Withdraw Pending C: Cpipe service TLV: (Type, Length: Value) |
|
Displays the service type exchanging labels; possible types displayed are VPLS, Epipe, Spoke, and Unknown |
|
Displays the value used by each end of an SDP tunnel to identify the VC |
|
Displays the unique service identification number identifying the service in the service domain |
|
Displays the IP address of the peer |
|
Displays the P2MP ID assigned by the root to this MVPN instance |
|
Displays the logical identifier assigned locally to identify the P2MP tunnel |
|
Displays the IP address of the root of the P2MP tree |
|
Displays the label operation carried out (can be one of pop | swap | push) |
|
Displays the next hop gateway IP address |
|
Displays the LSP tunnel ID (not the LSP path ID) |
|
Displays the ingress LDP label U — Label in use R — Label released |
|
Displays the egress LDP label |
|
Displays the local MTU value |
|
Displays the remote MTU value |
|
Displays the total number of LDP bindings on the router |
active
show>router>ldp>bindings
Supported on all 7210 SAS platforms as described in this document.
Commands in this context display information about LDP active bindings.
The following output is an example of LDP active bindings information, and Table: Output fields: LDP active bindings describes the LDP active bindings output fields.
Sample output*A:Dut-A# /show router ldp bindings active
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.1:0)
(IPv6 LSR ID ::[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
(S) - Static (M) - Multi-homed Secondary Support
(B) - BGP Next Hop (BU) - Alternate Next-hop for Fast Re-Route
(C) - FEC resolved for class-based-forwarding
===============================================================================
LDP IPv4 Prefix Bindings (Active)
===============================================================================
Prefix Op IngLbl EgrLbl
EgrNextHop EgrIf/LspId
-------------------------------------------------------------------------------
No. of IPv4 Prefix Active Bindings: 10
===============================================================================
===============================================================================
LDP IPv6 Prefix Bindings (Active)
===============================================================================
Prefix Op IngLbl EgrLbl
EgrNextHop EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
===============================================================================
LDP Generic IPv4 P2MP Bindings (Active)
===============================================================================
P2MP-Id Interface
RootAddr Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
*A:Dut-A#
|
Label |
Description |
|---|---|
|
|
Displays the LDP IPv4 and IPv6 bindings |
|
|
Description of the legend used in LDP active binding output U: Label In Use N: Label Not In Use W: Label Withdrawn WP: Label Withdraw Pending BU: Alternate For Fast Re-Route (S): Static (M): Multi-homed Secondary Support (B): BGP Next Hop (BU): Alternate Next-hop for Fast Re-Route (C): FEC resolved for class-based-forwarding |
|
|
Displays the active LDP IPv4 bindings |
|
|
Displays the label binding for the LDP prefix |
|
|
Displays the label operation (can be either pop, swap, or push) |
|
|
Displays the ingress LDP label |
|
|
Displays the egress LDP label |
|
|
Displays the next-hop information for the LDP prefix |
|
|
Displays the egress interface information for the LSP tunnel ID (not the LSP path ID) |
|
|
Displays the number of active IPv4 prefix bindings |
|
|
Displays the active LDP IPv6 bindings |
|
|
Displays the active generic LDP IPv4 P2MP bindings |
|
|
Displays the P2MP ID |
RootAddr |
Displays the root address |
|
|
Displays egress next-hop information |
ipv4 [summary | detail] [egress-if port-id]
ipv4 [summary | detail] [egress-lsp tunnel-id]
ipv4 [summary | detail] [egress-nh ip-address]
show>router>ldp>bindings>active
Supported on all 7210 SAS platforms as described in this document.
This command displays LDP active IPv4 bindings.
Displays LDP active bindings by matching the egress interface.
Specifies the tunnel identifier for the egress LSP.
Displays LDP active bindings by matching the egress next hop.
Displays detailed information about LDP active IPv4 bindings.
Displays LDP active IPv4 bindings information in a summarized format.
The following output is an example of LDP active IPv4 bindings information, and Table: Output fields: LDP active IPv4 bindings describes the LDP active IPv4 bindings output fields.
Sample output*A:Dut-A# /show router ldp bindings active ipv4
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.1:0)
(IPv6 LSR ID ::[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
(S) - Static (M) - Multi-homed Secondary Support
(B) - BGP Next Hop (BU) - Alternate Next-hop for Fast Re-Route
(C) - FEC resolved for class-based-forwarding
===============================================================================
LDP IPv4 Prefix Bindings (Active)
===============================================================================
Prefix Op IngLbl EgrLbl
EgrNextHop EgrIf/LspId
-------------------------------------------------------------------------------
10.20.1.1/32 Pop 131071 --
-- --
10.20.1.2/32 Push -- 131071
10.10.1.2 1/1/6
10.20.1.2/32 Swap 131064 131071
10.10.1.2 1/1/6
10.20.1.3/32 Push -- 131071
10.10.2.3 1/1/4
10.20.1.3/32 Swap 131063 131071
10.10.2.3 1/1/4
10.20.1.4/32 Push -- 131056
10.10.2.3 1/1/4
10.20.1.4/32 Swap 131049 131056
10.10.2.3 1/1/4
10.20.1.6/32 Push -- 131054
10.10.2.3 1/1/4
10.20.1.6/32 Swap 131048 131054
10.10.2.3 1/1/4
11.11.11.0/32(S) Pop 131070 --
-- --
-------------------------------------------------------------------------------
No. of IPv4 Prefix Active Bindings: 30
===============================================================================
===============================================================================
LDP Generic IPv4 P2MP Bindings (Active)
===============================================================================
P2MP-Id Interface
RootAddr Op IngLbl EgrLbl
EgrNH EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
*A:Dut-A#
|
Label |
Description |
|---|---|
|
|
Displays the LDP IPv4 bindings |
|
|
Description of the legend used in LDP active IPv4 binding output U: Label In Use N: Label Not In Use W: Label Withdrawn WP: Label Withdraw Pending BU: Alternate For Fast Re-Route (S): Static (M): Multi-homed Secondary Support (B): BGP Next Hop (BU): Alternate Next-hop for Fast Re-Route (C): FEC resolved for class-based-forwarding |
|
|
Displays the active LDP IPv4 bindings |
|
|
Displays the label binding for the LDP prefix |
|
|
Displays the label operation (can be either pop, swap, or push) |
|
|
Displays the ingress LDP label |
|
|
Displays the egress LDP label |
|
|
Displays the next-hop information for the LDP prefix |
|
|
Displays the egress interface information for the LSP tunnel ID (not the LSP path ID) |
|
|
Displays the number of active IPv4 prefix bindings |
|
|
Displays the active generic LDP IPv4 P2MP bindings |
|
|
Displays the P2MP ID |
RootAddr |
Displays the root address |
|
|
Displays egress next-hop information |
ipv6 [summary | detail] [egress-if port-id]
ipv6 [summary | detail] [egress-lsp tunnel-id]
ipv6 [summary | detail] [egress-nh ip-address]
show>router>ldp>bindings>active
7210 SAS-Mxp and 7210 SAS-Sx/S 1/10GE (standalone)
This command displays LDP active IPv6 bindings.
Displays LDP active bindings by matching the egress interface.
Specifies the tunnel identifier for the egress LSP.
Displays LDP active bindings by matching the egress next-hop.
Displays detailed information about LDP active IPv6 bindings.
Displays LDP active IPv6 bindings information in a summarized format.
The following output is an example of LDP active IPv6 bindings information, and Table: Output fields: LDP active IPv6 bindings describes theLDP active IPv6 bindings output fields.
Sample output*A:Dut-A# /show router ldp bindings active ipv6
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.1:0)
(IPv6 LSR ID ::[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
WP - Label Withdraw Pending, BU - Alternate For Fast Re-Route
(S) - Static (M) - Multi-homed Secondary Support
(B) - BGP Next Hop (BU) - Alternate Next-hop for Fast Re-Route
(C) - FEC resolved for class-based-forwarding
===============================================================================
LDP IPv6 Prefix Bindings (Active)
===============================================================================
Prefix Op IngLbl EgrLbl
EgrNextHop EgrIf/LspId
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
*A:Dut-A#
|
Label |
Description |
|---|---|
|
|
Displays the LDP IPv6 bindings |
|
|
Description of the legend used in LDP active IPv6 binding output U: Label In Use N: Label Not In Use W: Label Withdrawn WP: Label Withdraw Pending BU: Alternate For Fast Re-Route (S): Static (M): Multi-homed Secondary Support (B): BGP Next Hop (BU): Alternate Next-hop for Fast Re-Route (C): FEC resolved for class-based-forwarding |
|
|
Displays the active LDP IPv6 bindings |
|
|
Displays the label information for the IPv6 prefix |
|
|
Displays the label operation (can be either pop, swap, or push) |
|
|
Displays the ingress LDP label |
|
|
Displays the egress LDP label |
|
|
Displays the next-hop information for the LDP prefix |
|
|
Displays the egress interface information for the LSP tunnel ID (not the LSP path ID) |
ipv4 [session ip-addr[label-space]] [summary | detail]
show>router>ldp>bindings
Supported on all 7210 SAS platforms as described in this document.
This command displays LDP IPv4 bindings.
Specifies the IP address and label space identifier.
Displays detailed information about LDP IPv4 bindings.
Displays LDP IPv4 bindings information in a summarized format.
The following output is an example of LDP IPv4 bindings information, and Table: Output fields: LDP IPv4 bindings describes the LDP IPv4 bindings output fields.
Sample output*A:Dut-A# /show router ldp bindings ipv4
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.1:0)
(IPv6 LSR ID ::[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
S - Status Signaled Up, D - Status Signaled Down
E - Epipe Service, V - VPLS Service, M - Mirror Service
A - Apipe Service, F - Fpipe Service, I - IES Service, R - VPRN service
P - Ipipe Service, WP - Label Withdraw Pending
BU - Alternate For Fast Re-Route, TLV - (Type, Length: Value)
===============================================================================
LDP IPv4 Prefix Bindings
===============================================================================
Prefix IngLbl EgrLbl
Peer EgrIntf/LspId
EgrNextHop
-------------------------------------------------------------------------------
10.20.1.1/32 131071U --
10.20.1.2:0 --
--
10.20.1.1/32 131071U --
10.20.1.3:0 --
--
10.20.1.2/32 -- 131071
10.20.1.2:0 1/1/6
10.10.1.2
10.20.1.2/32 131064U 131063
10.20.1.3:0 --
--
10.20.1.3/32 131063U 131057
10.20.1.2:0 --
--
10.20.1.3/32 -- 131071
10.20.1.3:0 1/1/4
10.10.2.3
10.20.1.4/32 131049U 131056
10.20.1.2:0 --
--
-------------------------------------------------------------------------------
No. of IPv4 Prefix Bindings: 40
===============================================================================
===============================================================================
LDP Generic IPv4 P2MP Bindings
===============================================================================
P2MP-Id
RootAddr Interface IngLbl EgrLbl
EgrNH EgrIf/LspId
Peer
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
*A:Dut-A#
|
Label |
Description |
|---|---|
|
|
Displays the LDP IPv4 bindings |
|
|
Description of the legend used in LDP IPv4 binding output U: Label In Use N: Label Not In Use W: Label Withdrawn WP: Label Withdraw Pending BU: Alternate For Fast Re-Route (S): Static (M): Multi-homed Secondary Support (B): BGP Next Hop (BU): Alternate Next-hop for Fast Re-Route (C): FEC resolved for class-based-forwarding |
|
|
Displays the LDP IPv4 bindings |
|
|
Displays the label binding for the LDP prefix |
|
|
Displays the label operation (can be either pop, swap, or push) |
|
|
Displays the ingress LDP label |
|
|
Displays the egress LDP label |
|
|
Displays the next-hop information for the LDP prefix |
|
|
Displays the egress interface information for the LSP tunnel ID (not the LSP path ID) |
|
|
Displays the number of IPv4 prefix bindings |
|
|
Displays the generic LDP IPv4 P2MP bindings |
|
|
Displays the P2MP ID |
RootAddr |
Displays the root address |
|
|
Displays egress next-hop information |
ipv6 [session ip-addr[label-space]] [summary | detail]
show>router>ldp>bindings
7210 SAS-Mxp
This command displays LDP IPv6 bindings.
Specifies the IP address and label space identifier.
Displays detailed information about LDP IPv6 bindings.
Displays LDP IPv6 bindings information in a summarized format.
The following output is an example of LDP IPv6 bindings information, and Table: Output fields: LDP IPv6 bindings describes the LDP IPv6 bindings output fields.
Sample output*A:Dut-A# /show router ldp bindings ipv6
===============================================================================
LDP Bindings (IPv4 LSR ID 10.20.1.1:0)
(IPv6 LSR ID ::[0])
===============================================================================
Legend: U - Label In Use, N - Label Not In Use, W - Label Withdrawn
S - Status Signaled Up, D - Status Signaled Down
E - Epipe Service, V - VPLS Service, M - Mirror Service
A - Apipe Service, F - Fpipe Service, I - IES Service, R - VPRN service
P - Ipipe Service, WP - Label Withdraw Pending
BU - Alternate For Fast Re-Route, TLV - (Type, Length: Value)
===============================================================================
LDP IPv6 Prefix Bindings
===============================================================================
Prefix IngLbl EgrLbl
Peer EgrIntf/LspId
EgrNextHop
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
*A:Dut-A#
|
Label |
Description |
|---|---|
|
|
Displays the LDP IPv6 bindings |
|
|
Description of the legend used in LDP IPv6 binding output U: Label In Use N: Label Not In Use W: Label Withdrawn WP: Label Withdraw Pending BU: Alternate For Fast Re-Route (S): Static (M): Multi-homed Secondary Support (B): BGP Next Hop (BU): Alternate Next-hop for Fast Re-Route (C): FEC resolved for class-based-forwarding |
|
|
Displays the LDP IPv6 bindings |
|
|
Displays the label information for the IPv6 prefix |
|
|
Displays the label operation (can be either pop, swap, or push) |
|
|
Displays the ingress LDP label |
|
|
Displays the egress LDP label |
|
|
Displays the next-hop information for the LDP prefix |
|
|
Displays the egress interface information for the LSP tunnel ID (not the LSP path ID) |
discovery [{peer [ip-address]} | {interface [ip-int-name]}] [state state] [detail] [adjacency-type type]
show>router>ldp
Supported on all 7210 SAS platforms as described in this document.
This command displays the status of the interfaces participating in LDP discovery.
Specifies the IP address of the peer.
Specifies the name of an existing interface. If the string contains special characters (#, $, spaces, and so on), the entire string must be enclosed within double quotes.
Specifies to display the current operational state of the adjacency.
Specifies to display detailed information.
Specifies to display the adjacency type.
The following output is an example of LDP discovery information, and Table: Output fields: LDP discovery describes the LDP discovery output fields.
Sample output*A:Dut-A# show router ldp discovery
===============================================================================
LDP IPv4 Hello Adjacencies
===============================================================================
Interface Name Local Addr State
AdjType Peer Addr
-------------------------------------------------------------------------------
N/A 10.20.1.1:0 Estab
targ 10.20.1.2:0
N/A 10.20.1.1:0 Estab
targ 10.20.1.3:0
N/A 10.20.1.1:0 Estab
targ 10.20.1.7:0
a2c 10.20.1.1:0 Estab
link 10.20.1.3:0
a2b 10.20.1.1:0 Estab
link 10.20.1.2:0
-------------------------------------------------------------------------------
No. of IPv4 Hello Adjacencies: 5
===============================================================================
===============================================================================
LDP IPv6 Hello Adjacencies
===============================================================================
Interface Name Local Addr State
AdjType Peer Addr
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
*A:Dut-A#
Label |
Description |
|---|---|
|
Displays the name of the interface |
|
Displays the IP address of the originating (local) router |
|
Displays the IP address of the peer |
|
Displays the adjacency type between the LDP peer and LDP session is targeted |
|
Established — The adjacency is established Trying — The adjacency is not yet established |
|
Displays the total number of hello adjacencies discovered |
|
Displays the amount of time the adjacency has been enabled |
|
Displays the time left before a neighbor is declared to be down |
|
Displays the number of hello messages received for this adjacency |
|
Displays the number of hello messages that have been sent for this adjacency |
|
Displays the configuration sequence number that was in the hello received when this adjacency started up. This configuration sequence number changes when there is a change of configuration. |
|
Displays the IP address used on the remote end for the LDP session |
|
Displays the configuration sequence number that was used in the hello sent when this adjacency started up. This configuration sequence number changes when there is a change of configuration. |
|
Displays the IP address used locally for the LDP session |
interface [ip-int-name | ip-address] [detail]
show>router>ldp
Supported on all 7210 SAS platforms as described in this document.
This command displays configuration information about LDP interfaces.
Specifies the name of an existing interface. If the string contains special characters (#, $, spaces, and so on), the entire string must be enclosed within double quotes.
Specifies the IP address of the LDP neighbor.
Displays detailed information.
The following output is an example of LDP interface information, and Table: Output fields: LDP interface describes the output fields.
Sample output
*A:ALU_SIM11>show>router>ldp# interface
===============================================================================
LDP Interfaces
===============================================================================
Interface Adm Opr Hello Hold KA KA Transport
Factor Time Factor Timeout Address
-------------------------------------------------------------------------------
a Up Up 3 15 3 30 System
-------------------------------------------------------------------------------
No. of Interfaces: 1
===============================================================================
*A:ALU_SIM11>show>router>ldp# interface detail
*A:ALU_SIM11>show>router>ldp#
===============================================================================
LDP Interfaces (Detail)
===============================================================================
Interface "a"
-------------------------------------------------------------------------------
Admin State : Up Oper State : Up
Hold Time : 15 Hello Factor : 3
Keepalive Timeout : 30 Keepalive Factor : 3
Transport Addr : System Last Modified : 07/06/2010 10:36:59
Active Adjacencies : 1
Tunneling : Disabled
Lsp Name : None
===============================================================================
*A:ALU_SIM11>show>router>ldp#
Label |
Description |
|---|---|
|
Displays the interface associated with the LDP instance |
|
Up — The LDP is administratively enabled Down — The LDP is administratively disabled |
|
Up — The LDP is operationally enabled Down — The LDP is operationally disabled |
|
Displays the value by which the hello timeout should be divided to give the hello time, for example, the time interval, in seconds, between LDP hello messages. LDP uses hello messages to discover neighbors and to detect loss of connectivity with its neighbors. |
|
Displays the hello time, also known as hold time. It is the time interval, in seconds, that LDP waits before declaring a neighbor to be down. Hello timeout is local to the system and is sent in the hello messages to a neighbor. |
|
Displays the value by which the keepalive timeout should be divided to give the keepalive time, for example, the time interval, in seconds, between LDP keepalive messages. LDP keepalive messages are sent to keep the LDP session from timing out when no other LDP traffic is being sent between the neighbors. |
|
Displays the time interval, in seconds, that LDP waits before tearing down a session. If no LDP messages are exchanged during this time interval, the LDP session is torn down. Generally the value is configured to be 3 times the keepalive time (the time interval between successive LDP keepalive messages). |
|
Enabled — Authentication using MD5 message based digest protocol is enabled Disabled — No authentication is used |
|
Displays the total number of LDP interfaces |
parameters
show>router>ldp
Supported on all 7210 SAS platforms as described in this document.
This command displays configuration information about LDP parameters.
The following output is an example of LDP parameter information, and Table: Output fields: LDP parameters describes the output fields.
Sample output*A:SRU4>config>router>ldp# show router ldp parameters
===============================================================================
LDP Parameters (LSR ID 10.20.1.4)
===============================================================================
-------------------------------------------------------------------------------
Graceful Restart Parameters
-------------------------------------------------------------------------------
Nbor Liveness Time : 5 sec Max Recovery Time : 30
-------------------------------------------------------------------------------
Interface Parameters
-------------------------------------------------------------------------------
Keepalive Timeout : 30 sec Keepalive Factor : 3
Hold Time : 15 sec Hello Factor : 3
Propagate Policy : system Transport Address : system
Deaggregate FECs : False Route Preference : 9
Label Distribution : downstreamUnsolicited Label Retention : liberal
Control Mode : ordered Loop Detection : none
-------------------------------------------------------------------------------
Targeted Session Parameters
-------------------------------------------------------------------------------
Keepalive Timeout : 40 sec Keepalive Factor : 4
Hold Time : 45 sec Hello Factor : 3
Passive Mode : False Targeted Sessions : Enabled
===============================================================================
*A:SRU4>config>router>ldp#
Label |
Description |
|---|---|
|
Displays the factor used to derive the Keepalive interval |
|
Displays the time interval, in seconds, that LDP waits before tearing down the session |
|
Displays the time left before a neighbor is declared to be down |
|
Displays the value by which the hello timeout should be divided to give the hello time, for example, the time interval, in seconds, between LDP hello messages. LDP uses hello messages to discover neighbors and to detect loss of connectivity with its neighbors. |
|
Enabled — Authentication using MD5 message based digest protocol is enabled Disabled — No authentication is used |
|
true — LDP responds only when it gets a connect request from a peer and will not attempt to actively connect to its neighbors false — LDP actively tries to connect to its peers |
|
true — Targeted sessions are enabled false — Targeted sessions are disabled |
session [ip-addr[:label-space]] [detail | statistics [packet-type]] [session-type]
show>router>ldp
Supported on all 7210 SAS platforms as described in this document.
This command displays configuration information about LDP sessions.
Specifies the IP address of the LDP peer.
Specifies the label space identifier that the router is advertising on the interface.
Displays detailed information.
Specifies the packet type.
Specifies to display the session type.
The following output is an example of LDP session information, and Table: Output fields: LDP session describes the output fields.
Sample output*A:SRU4>config>router>ldp# show router ldp session
==============================================================================
LDP Sessions
==============================================================================
Peer LDP Id Adj Type State Msg Sent Msg Recv Up Time
------------------------------------------------------------------------------
10.1.1.1:0 Link Nonexistent 2 1 0d 00:00:04
10.8.100.15:0 Both Nonexistent 14653 21054 0d 12:48:25
10.20.1.20:0 Both Established 105187 84837 0d 12:48:27
10.20.1.22:0 Both Established 144586 95148 0d 12:48:23
10.22.10.2:0 Link Nonexistent 4 2 0d 00:00:16
10.22.11.2:0 Link Nonexistent 4 4 0d 00:00:14
10.22.13.2:0 Link Nonexistent 5 6 0d 00:00:20
10.66.33.1:0 Link Nonexistent 6 7 0d 00:00:25
10.66.34.1:0 Link Nonexistent 2 2 0d 00:00:05
10.66.35.1:0 Link Nonexistent 4 4 0d 00:00:14
10.20.1.1:0 Targeted Nonexistent 0 1 0d 00:00:04
10.20.1.3:0 Both Established 94 97 0d 00:00:55
10.20.1.5:0 Both Established 230866 286216 0d 12:48:27
10.20.1.110:0 Link Nonexistent 2 2 0d 00:00:05
10.0.0.1:0 Link Nonexistent 2 2 0d 00:00:05
------------------------------------------------------------------------------
No. of Sessions: 15
==============================================================================
*A:SRU4>config>router>ldp#
*A:SRU4>config>router>ldp# show router ldp session 10.20.1.20:0
==============================================================================
LDP Sessions
==============================================================================
Peer LDP Id Adj Type State Msg Sent Msg Recv Up Time
------------------------------------------------------------------------------
10.20.1.20:0 Both Established 105204 84859 0d 12:49:05
------------------------------------------------------------------------------
No. of Sessions: 1
==============================================================================
*A:SRU4>config>router>ldp#
*7210SAS# show router ldp session detail
===============================================================================
LDP Sessions (Detail)
===============================================================================
Legend: DoD - Downstream on Demand (for address FEC's only)
DU - Downstream Unsolicited
===============================================================================
-------------------------------------------------------------------------------
Session with Peer 10.3.3.3:0
-------------------------------------------------------------------------------
Adjacency Type : Link State : Established
Up Time : 0d 16:59:13
Max PDU Length : 4096 KA/Hold Time Remaining: 26
Link Adjacencies : 1 Targeted Adjacencies : 0
Local Address : 10.1.1.1 Peer Address : 10.3.3.3
Local TCP Port : 646 Peer TCP Port : 59116
Local KA Timeout : 30 Peer KA Timeout : 30
Mesg Sent : 22100 Mesg Recv : 21926
FECs Sent : 16 FECs Recv : 13
GR State : Capable Label Distribution : DU
Nbr Liveness Time : 0 Max Recovery Time : 0
Number of Restart : 0 Last Restart Time : Never
P2MP : Capable MP MBB : Capable
Dynamic Capability: Yes
Advertise : Address
-------------------------------------------------------------------------------
Session with Peer 10.2.2.2:0, Local 10.1.1.1:0
-------------------------------------------------------------------------------
Adjacency Type : Both State : Established
Up Time : 0d 00:07:48
Max PDU Length : 4096 KA/Hold Time Remaining: 29
Link Adjacencies : 1 Targeted Adjacencies : 1
Local Address : 10.1.1.1 Peer Address : 10.2.2.2
Local TCP Port : 646 Peer TCP Port : 50980
Local KA Timeout : 30 Peer KA Timeout : 30
Mesg Sent : 478 Mesg Recv : 480
FECs Sent : 182 FECs Recv : 170
Addrs Sent : 13 Addrs Recv : 16
GR State : Capable Label Distribution : DU
Nbr Liveness Time : 0 Max Recovery Time : 0
MP MBB : Not Capable
Dynamic Capability: Not Capable
Advertise : Address/Servi* BFD Operational Status: inService
-------------------------------------------------------------------------------
Session with Peer 10.3.3.3:0, Local 10.1.1.1:0
-------------------------------------------------------------------------------
Adjacency Type : Both State : Established
Up Time : 0d 00:07:48
Max PDU Length : 4096 KA/Hold Time Remaining: 29
Link Adjacencies : 1 Targeted Adjacencies : 1
Local Address : 10.1.1.1 Peer Address : 10.3.3.3
Local TCP Port : 646 Peer TCP Port : 49823
Local KA Timeout : 30 Peer KA Timeout : 30
Mesg Sent : 502 Mesg Recv : 418
FECs Sent : 124 FECs Recv : 124
Addrs Sent : 13 Addrs Recv : 5
GR State : Capable Label Distribution : DU
Nbr Liveness Time : 0 Max Recovery Time : 0
MP MBB : Not Capable
Dynamic Capability: Not Capable
Advertise : Address/Servi* BFD Operational Status: inService
-------------------------------------------------------------------------------
Session with Peer 10.4.4.4:0, Local 10.1.1.1:0
-------------------------------------------------------------------------------
Adjacency Type : Targeted State : Established
Up Time : 0d 00:07:47
Max PDU Length : 4096 KA/Hold Time Remaining: 36
Link Adjacencies : 0 Targeted Adjacencies : 1
Local Address : 10.1.1.1 Peer Address : 10.4.4.4
Local TCP Port : 646 Peer TCP Port : 51307
Local KA Timeout : 40 Peer KA Timeout : 40
Mesg Sent : 122 Mesg Recv : 124
FECs Sent : 36 FECs Recv : 36
Addrs Sent : 13 Addrs Recv : 3
GR State : Capable Label Distribution : DU
Nbr Liveness Time : 0 Max Recovery Time : 0
MP MBB : Not Capable
Dynamic Capability: Not Capable
Advertise : Service BFD Operational Status: inService
===============================================================================
* indicates that the corresponding row element may have been truncated.
Label |
Description |
|---|---|
|
Displays the IP address of the LDP peer |
|
Specifies that the adjacency type between the LDP peer and LDP session is targeted Link — Specifies that this adjacency is a result of a link hello Targeted — Specifies that this adjacency is a result of a targeted hello |
|
Established — The adjacency is established Trying — The adjacency is not yet established |
|
Displays the number of messages sent |
|
Displays the number of messages received |
|
Displays the amount of time the adjacency has been enabled |
session-parameters [family]
session-parameters [peer-ip-address]
show>router>ldp
Supported on all 7210 SAS platforms as described in this document.
This command displays LDP peer information.
Specifies a peer family for which to display information.
Specifies the IP address of a targeted LDP peer for which to display information.
The following output is an example of LDP peer information.
Sample output===============================================================================
LDP IPv4 Session Parameters
===============================================================================
-------------------------------------------------------------------------------
Peer : 10.12.12.12
-------------------------------------------------------------------------------
DOD : Disabled Adv Adj Addr Only : Disabled
FEC129 Cisco Inter*: Disabled
PE-ID MAC Flush In*: Disabled
Fec Limit : 0 Fec Limit Threshold: 90
Fec Limit Log Only : Disabled
Import Policies : None Export Policies : None
IPv4 Prefix Fec Cap: Enabled IPv6 Prefix Fec Cap: Disabled
P2MP Fec Cap : Disabled
Address Export : None
===============================================================================
No. of IPv4 Peers: 1
===============================================================================
* indicates that the corresponding row element may have been truncated.
===============================================================================
LDP IPv6 Session Parameters
===============================================================================
No Matching Entries Found
===============================================================================
statistics
show>router>ldp
Supported on all 7210 SAS platforms as described in this document.
This command displays LDP statistics information.
The following output is an example of LDP statistics information.
Sample output===============================================================================
LDP Statistics for IPv4 LSR ID 10.20.1.1:0
IPv6 LSR ID 2001:db8::4444[0]
===============================================================================
Session/Discovery
-------------------------------------------------------------------------------
Active IPv4 Sess : 5 Active IPv6 Sess : 0
Active IPv4 LinkAdj: 21 Active IPv6 LinkAdj : 0
Active IPv4 TargAdj: 5 Active IPv6 TargAdj : 0
Active IPv4 If : 31 Inactive IPv4 If : 0
Active IPv6 If : 0 Inactive IPv6 If : 0
Active IPv4 Peers : 5 Inactive IPv4 Peers : 0
Active IPv6 Peers : 0 Inactive IPv6 Peers : 0
IPv4 Attempted Sess: 40 IPv6 Attempted Sess : 0
IPv4 OLoad If : 0 IPv4 OLoad Targ Peers: 0
IPv6 OLoad If : 0 IPv6 OLoad Targ Peers: 0
-------------------------------------------------------------------------------
Protocol Stats
-------------------------------------------------------------------------------
No Hello Err : 0 Param Adv Err : 0
Max PDU Err : 0 Label Range Err : 0
Bad LDP Id Err : 0 Bad PDU Len Err : 0
Bad Mesg Len Err : 0 Bad TLV Len Err : 0
Unknown TLV Err : 0 Bad Proto Ver Err : 0
Malformed TLV Err : 0 Keepalive Expired Err: 9
Shutdown Notif Sent: 0 Shutdown Notif Recv : 0
-------------------------------------------------------------------------------
Prefixes
-------------------------------------------------------------------------------
IPv4 Pfx FECs Sent : 25 IPv4 Pfx FECs Recv : 25
IPv6 Pfx FECs Sent : 0 IPv6 Pfx FECs Recv : 0
IPv4PfxFecOLSessSnt: 0 IPv4PfxFecOLSessRecv : 0
IPv6PfxFecOLSessSnt: 0 IPv6PfxFecOLSessRecv : 0
IPv4PfxFecInOLoad : 0 IPv6PfxFecInOLoad : 0
-------------------------------------------------------------------------------
P2MP
-------------------------------------------------------------------------------
IPv4 P2MP FECs Sent: 0 IPv4 P2MP FECs Recv : 0
IPv6 P2MP FECs Sent: 0 IPv6 P2MP FECs Recv : 0
IPv4P2MPFecOLSessSn: 0 IPv4P2MPFecOLSessRecv: 0
IPv6P2MPFecOLSessSn: 0 IPv6P2MPFecOLSessRecv: 0
IPv4P2MPFecInOLoad : 0 IPv6P2MPFecInOLoad : 0
-------------------------------------------------------------------------------
Services
-------------------------------------------------------------------------------
Svc FEC128s Sent : 0 Svc FEC128s Recv : 0
Svc FEC129s Sent : 0 Svc FEC129s Recv : 0
Svc Fec128 OLSessSn: 0 Svc Fec128 OLSessRecv: 0
Svc Fec129 OLSessSn: 0 Svc Fec129 OLSessRecv: 0
Svc Fec128 InOLoad : 0 Svc Fec129 InOLoad : 0
===============================================================================
status
show>router>ldp
Supported on all 7210 SAS platforms as described in this document.
This command displays LDP status information.
The following output is an example of LDP status information, and Table: Output fields: LDP status describes the output fields.
Sample outputA:7210SAS# show router ldp status
===============================================================================
LDP Status for LSR ID 10.1.1.1
===============================================================================
Admin State : Up Oper State : Up
Created at : 11/30/2009 21:22:31 Up Time : 0d 16:45:41
Oper Down Reason : n/a Oper Down Events : 1
Last Change : 11/30/2009 21:22:31 Tunn Down Damp Time : 20 sec
Label Withdraw Del*: 120 sec Implicit Null Label : Disabled
Short. TTL Prop Lo*: Enabled Short. TTL Prop Tran*: Enabled
Import Policies : Export Policies :
None ldp-reject
Aggregate Prefix : True Agg Prefix Policies: None
Dynamic Capability : True P2MP Capable : True
MP MBB Capable : True MP MBB Timer : 3
Active Adjacencies : 3 Active Sessions : 2
Active Interfaces : 23 Inactive Interfaces : 8
Active Peers : 4 Inactive Peers : 1
Addr FECs Sent : 34 Addr FECs Recv : 15
Serv FECs Sent : 0 Serv FECs Recv : 0
P2MP FECs Sent : 0 P2MP FECs Recv : 0
Attempted Sessions : 0
No Hello Err : 0 Param Adv Err : 0
Max PDU Err : 0 Label Range Err : 0
Bad LDP Id Err : 4296 Bad PDU Len Err : 0
Bad Mesg Len Err : 0 Bad TLV Len Err : 0
Unknown TLV Err : 0
Malformed TLV Err : 0 Keepalive Expired Err: 0
Shutdown Notif Sent: 0 Shutdown Notif Recv : 0
No Matching Entries Found
===============================================================================
A:7210SAS#
Label |
Description |
|---|---|
|
Up — The LDP is administratively enabled Down — The LDP is administratively disabled |
|
Up — The LDP is operationally enabled Down — The LDP is operationally disabled |
|
Displays the date and time when the LDP instance was created |
|
Displays the time, in hundredths of seconds, that the LDP instance has been operationally up |
|
Displays the date and time when the LDP instance was last modified |
|
Displays the number of times the LDP instance has gone operationally down since the instance was created |
|
Displays the number of active adjacencies (established sessions) associated with the LDP instance |
|
Displays the number of active sessions (session in some form of creation) associated with the LDP instance |
|
Displays the number of active (operationally up) interfaces associated with the LDP instance |
|
Displays the number of inactive (operationally down) interfaces associated with the LDP instance |
|
Displays the number of active LDP peers |
|
Displays the number of inactive LDP peers |
|
Displays the number of labels that have been sent to the peer associated with this FEC |
|
Displays the number of labels that have been received from the peer associated with this FEC |
|
Displays the number of labels that have been sent to the peer associated with this FEC |
|
Displays the number of labels that have been received from the peer associated with this FEC |
|
Displays the total number of attempted sessions for this LDP instance |
|
Displays the total number of ‟Session Rejected” or ‟No Hello Error” notification messages sent or received by this LDP instance |
|
Displays the total number of ‟Session Rejected” or ‟Parameters Advertisement Mode Error” notification messages sent or received by this LDP instance |
|
Displays the total number of ‟Session Rejected” or ‟Parameters Max PDU Length Error” notification messages sent or received by this LDP instance |
|
Displays the total number of ‟Session Rejected” or ‟Parameters Label Range Error” notification messages sent or received by this LDP instance |
|
Displays the number of bad LDP identifier fatal errors detected for sessions associated with this LDP instance |
|
Displays the number of bad PDU length fatal errors detected for sessions associated with this LDP instance |
|
Displays the number of bad message length fatal errors detected for sessions associated with this LDP instance |
|
Displays the number of bad TLV length fatal errors detected for sessions associated with this LDP instance |
|
Displays the number of malformed TLV value fatal errors detected for sessions associated with this LDP instance |
|
Displays the number of shutdown notifications sent related to sessions associated with this LDP instance |
|
Displays the number of session Keepalive timer expired errors detected for sessions associated with this LDP instance |
|
Displays the number of shutdown notifications received related to sessions associated with this LDP instance |
targ-peer [ip-address] [detail]
targ-peer [detail] family
targ-peer resource-failures [family]
show>router>ldp
Supported on all 7210 SAS platforms as described in this document.
This command displays targeted LDP peer information.
Displays detailed information.
Specifies a peer family for which to display information.
Specifies the IP address of a targeted LDP peer for which to display information.
Displays resource failure information for targeted LDP peers.
The following output is an example of targeted LDP peer information, and Table: Output fields: LDP targeted peers describes the output fields.
Sample output===============================================================================
LDP IPv4 Targeted Peers
===============================================================================
Peer Adm/ Hello Hold KA KA Auto
Opr Fctr Time Fctr Time Created
-------------------------------------------------------------------------------
10.1.1.1 Up/Up 3 45 4 40 yes
10.2.2.2 Up/Up 3 45 4 40 yes
10.3.3.3 Up/Up 3 45 4 40 yes
10.5.5.5 Up/Up 3 45 4 40 yes
10.6.6.6 Up/Up 3 45 4 40 yes
-------------------------------------------------------------------------------
No. of IPv4 Targeted Peers: 5
===============================================================================
===============================================================================
LDP IPv6 Targeted Peers
===============================================================================
Peer Adm/ Hello Hold KA KA Auto
Opr Fctr Time Fctr Time Created
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
Label |
Description |
|---|---|
Peer |
Displays the IP address of the peer |
Adm |
Up — indicates that LDP is administratively enabled Down — indicates that LDP is administratively disabled |
Opr |
Up — indicates that LDP is operationally enabled Down — indicates that LDP is operationally disabled |
Hello Factor |
The value by which the hello timeout should be divided to give the hello time; that is, the time interval, in seconds, between LDP Hello messages. LDP uses hello messages to discover neighbors and to detect loss of connectivity with its neighbors. |
Hold Time |
Displays the time interval, in seconds, that LDP waits before declaring a neighbor to be down. Hold time (also known as Hello time) is local to the system and is sent in the hello messages to a neighbor. |
Keepalive Factor |
Displays the value by which the keepalive timeout should be divided to give the keepalive time; that is, the time interval, in seconds, between LDP keepalive messages. LDP keepalive messages are sent to keep the LDP session from timing out when no other LDP traffic is being sent between the neighbors. |
Keepalive Timeout |
Displays the time interval, in seconds, that LDP waits before tearing down a session. If no LDP messages are exchanged during this time interval, the LDP session is torn down. Generally the value is configured to be three times the keepalive time (the time interval between successive LDP keepalive messages). |
Auto Create |
Specifies whether a targeted peer was automatically created through a Service Manager. For an LDP interface, this value is always false. |
No. of Peers |
Displays the total number of LDP peers |
tcp-session-parameters [family]
tcp-session-parameters [keychain keychain]
tcp-session-parameters [transport-peer-ip-address]
show>router>ldp
Supported on all 7210 SAS platforms as described in this document.
This command displays information about the TCP transport session of an LDP peer.
Specifies a peer family for which to display information.
Specifies the name of an auth-keychain, up to 32 characters.
Specifies the IP address of a TCP transport peer for which to display information.