Show commands

twamp-light

Syntax

twamp-light

Context

show>router

show>service

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

This command displays TWAMP Light information.

Output

The following output is an example of TWAMP light information, and Table: Output fields: TWAMP Light describes the output fields.

Sample output

show router twamp-light
-------------------------------------------------------------------------------
TWAMP-Light Reflector
-------------------------------------------------------------------------------
Admin State          : Up                      UDP Port         : 15000
Description          : (Not Specified)
Up Time              : 0d 00:02:24
Test Frames Received : 0                       Test Frames Sent : 0
-------------------------------------------------------------------------------

-------------------------------------------------------------------------------
TWAMP-Light Reflector Prefixes
-------------------------------------------------------------------------------
Prefix                                      Description
-------------------------------------------------------------------------------
172.16.1.0/24
-------------------------------------------------------------------------------
No. of TWAMP-Light Reflector Prefixes: 1
------------------------------------------------------------------------------- 


show service id 500 twamp-light
-------------------------------------------------------------------------------
TWAMP-Light Reflector
-------------------------------------------------------------------------------
Admin State          : Up                      UDP Port         : 15000
Description          : TWAMP Light reflector VPRN 500
Up Time              : 0d 01:47:12
Test Frames Received : 6431                    Test Frames Sent : 6431
-------------------------------------------------------------------------------

-------------------------------------------------------------------------------
TWAMP-Light Reflector Prefixes
-------------------------------------------------------------------------------
Prefix                                      Description
-------------------------------------------------------------------------------
10.2.1.1/32                                 Process only 10.2.1.1 TWAMP Light
                                            Packets
172.16.1.0/24                               Process all 172.16.1.0 TWAMP
                                            Light packets
-------------------------------------------------------------------------------
No. of TWAMP-Light Reflector Prefixes: 2
-------------------------------------------------------------------------------

Table: Output fields: TWAMP Light
Label	Description
TWAMP Light Reflector
Admin State	Up—Specifies that the server or prefix is administratively enabled (no shutdown) in configuration. Down—Specifies that the server or prefix is administratively disabled (shutdown) in configuration.
Decription	Text string to describe the context of the protocol.
Up Time	The time since the server process was started, measured in days (d), hours, minutes, and seconds
UDP Port	The UDP port number used
Test Frames Received	The total number of frames received from session senders
Test Frames Sent	The total number of frames sent to session senders
Prefixes	The time since the server process was started, measured in days (d), hours, minutes, and seconds

saa

Syntax

saa [test-name] [owner test-owner]

Context

show>saa

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

This command displays information about the SAA test.

If no specific test is specified, a summary of all configured tests is displayed.

If a specific test is specified, detailed test results for that test are displayed for the last three occurrences that this test has been executed, or since the last time the counters have been reset via a system reboot or clear command.

Parameters

test-name: Specifies the name of the SAA test for which the information needs to be displayed. The test name must already be configured in the config>saa>test context.

owner test-owner

Specifies the owner of an SAA operation up to 32 characters.

Values: 32 characters maximum.

Default: If a test-owner value is not specified, tests created by the CLI have a default owner ‟TiMOS CLI”.

Output

The following output is an example of SAA information, and Table: Output fields: SAA describes the output fields.

Sample output

*A:7210 SAS>show# saa

===============================================================================
SAA Test Information
===============================================================================
Test name                    : abc
Owner name                   : TiMOS CLI
Description                  : test
Accounting policy            : None
Administrative status        : Disabled
Test type                    : Not configured
Trap generation              : None
Test runs since last clear   : 0
Number of failed test runs   : 0
Last test result             : Undetermined
-------------------------------------------------------------------------------
Threshold
Type        Direction Threshold  Value      Last Event          Run #
-------------------------------------------------------------------------------
Jitter-in   Rising    None       None       Never               None
            Falling   None       None       Never               None
Jitter-out  Rising    None       None       Never               None
            Falling   None       None       Never               None
Jitter-rt   Rising    100        None       Never               None
            Falling   10.0       None       Never               None
Latency-in  Rising    None       None       Never               None
            Falling   None       None       Never               None
Latency-out Rising    None       None       Never               None
            Falling   None       None       Never               None
Latency-rt  Rising    100        None       Never               None
            Falling   20.0       None       Never               None
Loss-in     Rising    None       None       Never               None
            Falling   None       None       Never               None
Loss-out    Rising    None       None       Never               None
            Falling   None       None       Never               None
Loss-rt     Rising    300        None       Never               None
            Falling   30         None       Never               None

===============================================================================

===============================================================================
*A:7210 SAS>show#

Table: Output fields: SAA
Label	Description
`Test Name`	Specifies the name of the test.
`Owner Name`	Specifies the owner of the test.
`Description`	Specifies the description for the test type.
`Accounting policy`	Specifies the associated accounting policy ID.
`Administrative status`	Specifies whether the administrative status is enabled or disabled.
`Test type`	Specifies the type of test configured.
`Trap generation`	Specifies the trap generation for the SAA test.
`Test runs since last clear`	Specifies the total number of tests performed since the last time the tests were cleared.
`Number of failed tests run`	Specifies the total number of tests that failed.
`Last test run`	Specifies the last time a test was run.
`Threshold type`	Indicates the type of threshold event being tested, jitter-event, latency-event, or loss-event, and the direction of the test responses received for a test run: in — inbound out — outbound rt — roundtrip
`Direction`	Indicates the direction of the event threshold, rising or falling.
`Threshold`	Displays the configured threshold value.
`Value`	Displays the measured crossing value that triggered the threshold crossing event.
`Last event`	Indicates the time that the threshold crossing event occurred.
`Run #`	Indicates what test run produced the specified values.

test-oam

Syntax

test-oam

Context

show

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

Commands in this context display Operations, Administration, and Maintenance test parameters

Output

The following output is an example of OAM test parameters information.

Sample output

*A:Dut-A# show saa "Dut-A:1413:1501" owner "TiMOS"
===============================================================================
SAA Test Information
===============================================================================
Test name                    : Dut-A:1413:1501                                 
Owner name                   : TiMOS                                           
Administrative status        : Enabled                                         
Test type                    : vccv-ping 1413:1501 fc "nc" timeout 10 size 200
                               count 2
Test runs since last clear   : 1                                               
Number of failed test runs   : 0                                               
Last test result             : Success                                         
-------------------------------------------------------------------------------
Threshold
Type        Direction Threshold  Value      Last Event          Run #
-------------------------------------------------------------------------------
Jitter-in   Rising    None       None       Never               None     
            Falling   None       None       Never               None     
Jitter-out  Rising    None       None       Never               None     
            Falling   None       None       Never               None     
Jitter-rt   Rising    None       None       Never               None     
            Falling   None       None       Never               None     
Latency-in  Rising    None       None       Never               None     
            Falling   None       None       Never               None     
Latency-out Rising    None       None       Never               None     
            Falling   None       None       Never               None     
Latency-rt  Rising    100        None       Never               None     
            Falling   None       None       Never               None     
Loss-in     Rising    None       None       Never               None     
            Falling   None       None       Never               None     
Loss-out    Rising    None       None       Never               None     
            Falling   None       None       Never               None     
Loss-rt     Rising    2          None       Never               None     
            Falling   None       None       Never               None 
===============================================================================
Test Run: 144
Total number of attempts: 2
Number of requests that failed to be sent out: 0
Number of responses that were received: 2
Number of requests that did not receive any response: 0
Total number of failures: 0, Percentage: 0
 (in ms)            Min         Max     Average      Jitter
Outbound  :           0           0           0           0
Inbound   :          10          20          15           0
Roundtrip :          10          20          15           0
Per test packet: 
  Sequence    Outbound     Inbound   RoundTrip Result
         1           0          20          20 EgressRtr(10.20.1.4)
         2           0          10          10 EgressRtr(10.20.1.4)
===============================================================================
*A:Dut-A#

eth-cfm

Syntax

eth-cfm

Context

show

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

Commands in this context display CFM information.

association

Syntax

association [ma-index] [detail]

Context

show>eth-cfm

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

This command displays eth-cfm association information.

Parameters

ma-index

Specifies the MA index.

Values: 1 to 4294967295

detail: Specifies detailed information for the eth-cfm association.

Output

The following output is an example of ETH-CFM information, and Table: Output fields: ETH-CFM association describes the output fields.

Sample output


A:dut-b# show eth-cfm association 

======================================================================
CFM Association Table
======================================================================
Md-index   Ma-index   Name                     CCM-interval Bridge-id          
----------------------------------------------------------------------
1          1          a1                       1            1         
1          2          a2                       1            2         
2          1          a1                       1            2         
2          2          a2                       1            1         
======================================================================
A:dut-b#

Table: Output fields: ETH-CFM association
Label	Description
Md-index	Displays the MD index
Ma-index	Displays the MA index
Name	Displays the name of the MA
CCM-interval	Displays the CCM interval (in seconds)
Bridge-id	Displays the bridge ID for the MA. The bridge ID is the same value as the service ID of the service to which the MEP belongs.

cfm-stack-table

Syntax

cfm-stack-tableup | down[port [port-id [vlan vlan-id]]|sdp sdp-id[:vc-id]] [level 0..7] [direction up | down]

Context

show>eth-cfm

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

This command displays stack-table information. This stack-table is used to display the various management points MEPs and MIPs that are configured on the system. These can be Service based or facility based. If no parameters are included, the entire stack-table is displayed.

Parameters

port port-id: Specifies the bridge port or aggregated port on which MEPs or MHFs are configured.

vlan vlan-id

Specifies the associated VLAN ID.

Values: 0 to 4094

level

Specifies the MD level of the maintenance point.

Values: 0 to 7

direction up | down: Specifies the direction in which the MP faces on the bridge port.

Output

The following output is an example of CFM stack-table information, and Table: Output fields: CFM stack table describes the output fields.

Sample output

A:dut-b# show eth-cfm cfm-stack-table 
 
========================================================================
CFM SAP Stack Table
========================================================================
Sap            Level Dir  Md-index   Ma-index   Mep-id Mac-address             
------------------------------------------------------------------------
1/1/9:1        6     Down 1          1          1      00:25:ba:01:c3:6a
1/1/9:1        7     Down 2          2          1      00:25:ba:01:c3:6a
1/1/9:2        6     Down 1          2          1      00:25:ba:01:c3:6a
1/1/9:2        7     Down 2          1          1      00:25:ba:01:c3:6a
========================================================================
 
========================================================================
CFM Ethernet Tunnel Stack Table
========================================================================
Eth-tunnel     Level Dir  Md-index   Ma-index   Mep-id Mac-address             
------------------------------------------------------------------------
========================================================================
 
========================================================================
CFM SDP Stack Table
========================================================================
Sdp            Level Dir  Md-index   Ma-index   Mep-id Mac-address             
------------------------------------------------------------------------
No Matching Entries
========================================================================
 
========================================================================
CFM Virtual Stack Table
========================================================================
Service        Level Dir  Md-index   Ma-index   Mep-id Mac-address             
------------------------------------------------------------------------
No Matching Entries
========================================================================
A:dut-b#

Table: Output fields: CFM stack table
Label	Description
Sap	Displays the SAP identifier
Level	Displays the MD level of the domain
Dir (direction)	Displays the direction of OAMPDU transmission
Md-index	Displays the MD index of the domain
Ma-index	Displays the MA index of the domain
Mep-id	Displays the MEP identifier
Mac-address	Displays the MAC address of the MEP

domain

Syntax

domain [md-index] [association ma-index | all-associations] [detail]

Context

show>eth-cfm

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

This command displays domain information.

Parameters

md-index

Specifies the index of the MD to which the MP is associated, or 0, if none.

Values: [1..4294967295]

association ma-index: Specifies the index to which the MP is associated, or 0, if none.

all-associations: Specifies all associations to the MD.

detail: Specifies detailed domain information.

Output

The following output is an example of ETH-CFM domain information, and Table: Output fields: ETH-CFM domain describes the output fields.

Sample output

A:dut-b# show eth-cfm domain 

==============================================================================
CFM Domain Table
==============================================================================
Md-index   Level Name                                       Format             
------------------------------------------------------------------------------
1          6     d1                                         charString        
2          7     d2                                         charString        
==============================================================================
A:dut-b#

Table: Output fields: ETH-CFM domain
Label	Description
Domain
Md-index	Displays the MD index of the domain
Level	Displays the MD level of the domain
Name	Displays the name of the MD
Name Format	Displays the format for the MD name

mep

Syntax

mep mep-id domain md-index association ma-index [loopback] [linktrace] [eth-bandwidth-notification]

mep mep-id domain md-indexassociation ma-index [remote-mepid mep-id | all-remote-mepids]

mep mep-id domain md-index association ma-index eth-test-results [remote-peer mac-address]

mep mep-id domain md-index association ma-index one-way-delay-test [remote-peer mac-address]

mep mep-id domain md-index association ma-index two-way-delay-test [remote-peer mac-address]

mep mep-id domain md-index association ma-index two-way-slm-test [remote-peer mac-address]

Context

show>eth-cfm

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

This command displays information for a specified Maintenance Endpoint (MEP).

Parameters

domain md-index: Specifies the index of the MD to which the MP is associated, or 0, if none.

association ma-index: Specifies the index of the MA to which the MP is associated, or 0, if none.

loopback: Specifies loopback information for the MEP.

linktrace: Specifies linktrace information for the MEP.

eth-bandwidth-notification: Specifies the active ETH-BN notification parameters received from the peer and reported to the rate function on the associated port. This keyword is only supported on the 7210 SAS-Mxp, 7210 SAS-R6, and 7210 SAS-R12.

remote-mepid: Specifies remote MEP ID information for the MEP.

remote-peer mac-address: Specifies remote peer information for the MEP.

one-way-delay-test: Specifies one-way delay test information for the MEP.

two-way-delay-test: Specifies two-way delay test information for the MEP.

two-way-slm-test: Specifies two-way SLM test information for the MEP.

eth-test-results: Specifies ETH test result information for the MEP.

all-remote-mepids: Specifies all remote MEP information for the MEP.

statistics: Specifies MEP statistics.

detail: Specifies detailed MEP information.

Output

The following outputs are examples of MEP information, and the associated tables describe the output fields:

Sample output 1

A:dut-b# show eth-cfm mep 1 domain 1 association 1 linktrace 
-------------------------------------------------------------------------------
Mep Information
-------------------------------------------------------------------------------
Md-index           : 1                        Direction         : Down
Ma-index           : 1                        Admin             : Enabled
MepId              : 1                        CCM-Enable        : Enabled
IfIndex            : 35946496                 PrimaryVid        : 1
FngState           : fngReset                 ControlMep        : False
LowestDefectPri    : macRemErrXcon            HighestDefect     : none
Defect Flags       : None
Mac Address        : 00:25:ba:01:c3:6a        CcmLtmPriority    : 7
CcmTx              : 0                        CcmSequenceErr    : 0
Eth-1Dm Threshold  : 3(sec)                   
Eth-Ais:           : Disabled                 
Eth-Tst:           : Disabled                 
CcmLastFailure Frame:
    None
XconCcmFailure Frame:
    None
-------------------------------------------------------------------------------
Mep Linktrace Message Information
-------------------------------------------------------------------------------
LtRxUnexplained    : 0                        LtNextSequence    : 2
LtStatus           : False                    LtResult          : False
TargIsMepId        : False                    TargMepId         : 0
TargMac            : 00:00:00:00:00:00        TTL               : 64
EgressId           : 00:00:00:25:ba:01:c3:6a  SequenceNum       : 1
LtFlags            : useFDBonly
-------------------------------------------------------------------------------
Mep Linktrace Replies
-------------------------------------------------------------------------------
SequenceNum        : 1                        ReceiveOrder      : 1
Ttl                : 63                       Forwarded         : False
LastEgressId       : 00:00:00:25:ba:01:c3:6a  TerminalMep       : True
NextEgressId       : 00:00:00:25:ba:00:5e:bf  Relay             : rlyHit
ChassisIdSubType   : unknown value (0)        
ChassisId:
    None
ManAddressDomain:
    None
ManAddress:
    None
IngressMac         : 00:25:ba:00:5e:bf        Ingress Action    : ingOk
IngrPortIdSubType  : unknown value (0)        
IngressPortId:
    None                              
EgressMac          : 00:00:00:00:00:00        Egress Action     : egrNoTlv
EgrPortIdSubType   : unknown value (0)        
EgressPortId:
    None
Org Specific TLV:
    None
A:dut-b# 
A:dut-b# 

A:dut-b# show eth-cfm mep 1 domain 1 association 1 loopback 
-------------------------------------------------------------------------------
Mep Information
-------------------------------------------------------------------------------
Md-index           : 1                        Direction         : Down
Ma-index           : 1                        Admin             : Enabled
MepId              : 1                        CCM-Enable        : Enabled
IfIndex            : 35946496                 PrimaryVid        : 1
FngState           : fngReset                 ControlMep        : False
LowestDefectPri    : macRemErrXcon            HighestDefect     : none
Defect Flags       : None
Mac Address        : 00:25:ba:01:c3:6a        CcmLtmPriority    : 7
CcmTx              : 0                        CcmSequenceErr    : 0
Eth-1Dm Threshold  : 3(sec)                   
Eth-Ais:           : Disabled                 
Eth-Tst:           : Disabled                 
CcmLastFailure Frame:
    None
XconCcmFailure Frame:
    None
-------------------------------------------------------------------------------
Mep Loopback Information
-------------------------------------------------------------------------------
LbRxReply          : 1                        LbRxBadOrder      : 0
LbRxBadMsdu        : 0                        LbTxReply         : 0
LbSequence         : 2                        LbNextSequence    : 2
LbStatus           : False                    LbResultOk        : True
DestIsMepId        : False                    DestMepId         : 0
DestMac            : 00:00:00:00:00:00        SendCount         : 0
VlanDropEnable     : True                     VlanPriority      : 7
Data TLV:
    None
A:dut-b# 

*A:dut-b# show eth-cfm mep 1 domain 4 association 4 two-way-delay-test remote-
peer 00:25:ba:00:5e:bf 

==================================================================
Eth CFM Two-way Delay Test Result Table
==================================================================
Peer Mac Addr         Delay (us)          Delay Variation (us)                 
------------------------------------------------------------------
00:25:ba:00:5e:bf     507                 507                     
==================================================================
*A:dut-b#
*A:dut-b# show eth-cfm mep 1 domain 4 association 4 two-way-delay-test 

==================================================================
Eth CFM Two-way Delay Test Result Table
==================================================================
Peer Mac Addr         Delay (us)          Delay Variation (us)                 
------------------------------------------------------------------
00:25:ba:00:5e:bf     507                 507                     
==================================================================
*A:dut-b# 
*A:dut-a# show eth-cfm mep 2 domain 4 association 4  eth-test-results remote-
peer 00:25:ba:01:c3:6a 

==============================================================
Eth CFM ETH-Test Result Table
==============================================================
                                 Current        Accumulate                     
                  FrameCount     ErrBits        ErrBits                        
Peer Mac Addr     ByteCount      CrcErrs        CrcErrs                        
--------------------------------------------------------------
00:25:ba:01:c3:6a 6              0              0             
                  384            0              0             
==============================================================
*A:dut-a# 
*A:dut-a# show eth-cfm mep 2 domain 4 association 4  eth-test-results 

==============================================================
Eth CFM ETH-Test Result Table
==============================================================
                                 Current        Accumulate                     
                  FrameCount     ErrBits        ErrBits                        
Peer Mac Addr     ByteCount      CrcErrs        CrcErrs                        
--------------------------------------------------------------
00:25:ba:01:c3:6a 6              0              0             
                  384            0              0             
==============================================================
*A:dut-a# show eth-cfm mep 2 domain 4 association 4 one-way-delay-test remote-
peer 00:25:ba:01:c3:6a

==================================================================
Eth CFM One-way Delay Test Result Table
==================================================================
Peer Mac Addr         Delay (us)          Delay Variation (us)                 
------------------------------------------------------------------
00:25:ba:01:c3:6a     402                 402                
==================================================================
*A:dut-a# 

*A:dut-a# show eth-cfm mep 2 domain 4 association 4 one-way-delay-test 

==================================================================
Eth CFM One-way Delay Test Result Table
==================================================================
Peer Mac Addr         Delay (us)          Delay Variation (us)                 
------------------------------------------------------------------
00:25:ba:01:c3:6a     402                 402                
==================================================================
*A:dut-a# 

show eth-cfm mep 28 domain 14 association 2 all-remote-mepids detail
===============================================================================
Eth-CFM Remote-MEP Information
===============================================================================
Remote MEP ID    : 30                   State            : True/Grace
Auto Discovered  : False                RDI              : False
Port Status TLV  : Up                   I/F Status TLV   : Up
MAC Address      : 00:00:00:00:00:30    CCM Last Change  : 02/06/2014 21:37:00
Chass. ID SubType: local
Chassis ID       : access-012-west
Man Addr Domain  : (Not Specified)
Remote MEP ID    : 32                   State            : True/Grace
Auto Discovered  : True                 RDI              : False
Port Status TLV  : Up                   I/F Status TLV   : Up
MAC Address      : 00:00:00:00:00:32    CCM Last Change  : 02/06/2014 21:37:00
Chass. ID SubType: chassisComponent
Chassis ID       : (Not Specified)
Man Addr Domain  : (Not Specified)
=============================================================================== 

show eth-cfm mep 28 domain 14 association 2 remote-mepid 30 detail
===============================================================================
Eth-CFM Remote-MEP Information
===============================================================================
Remote MEP ID    : 30                   State            : True/Grace
Auto Discovered  : False                RDI              : False
Port Status TLV  : Up                   I/F Status TLV   : Up
MAC Address      : 00:00:00:00:00:30    CCM Last Change  : 02/06/2014 21:37:00
Chass. ID SubType: local
Chassis ID       : access-012-west
Man Addr Domain  : (Not Specified)
===============================================================================

show eth-cfm mep 28 domain 14 association 2 remote-mepid 30        
=============================================================================
Eth-CFM Remote-Mep Table
=============================================================================
R-mepId AD Rx CC RxRdi Port-Tlv If-Tlv Peer Mac Addr     CCM status since
-----------------------------------------------------------------------------
30      F  True  False Up       Up     00:00:00:00:00:30 02/06/2014 21:37:00
=============================================================================
Entries marked with a 'T' under the 'AD' column have been auto-discovered.

Table: Output fields: MEP
Label	Description
Mep Information
Md-index	Displays the MD index of the domain
Direction	Displays the direction of OAMPDU transmission
Ma-index	Displays the MA index of the association
Admin	Displays the administrative status of the MEP
MepId	Displays the MEP identifier
CCM-Enable	Displays the status of the CCM (enabled or disabled)
IfIndex	Displays the index of the interface
PrimaryVid	Displays the identifier of the primary VLAN
FngState	Indicates the different states of the Fault Notification Generator
LowestDefectPri	Displays the lowest priority defect (a configured value) that is allowed to generate a fault alarm
HighestDefect	Identifies the highest defect that is present (for example, if defRDICCM and defXconCCM are present, the highest defect is defXconCCM)
Defect Flags	Displays the number of defect flags
Mac Address	Displays the MAC address of the MEP
CcmLtmPriority	Displays the priority value transmitted in the linktrace messages (LTM)s and CCMs for this MEP. The MEP must be configured on a VLAN.
CcmTx	Displays the number of Continuity Check Messages (CCM) sent. The count is taken from the last polling interval (every 10 s).
CcmSequenceErr	Displays the number of CCM errors
Eth-1DM Threshold	Displays the one-way-delay threshold value
Eth-Ais	Displays the state of the ETH-AIS test (enabled or disabled)
Eth-Test	Displays the state of the ETH-Test (enabled or disabled)
CcmLastFailure Frame	Displays the frame that caused the last CCM failure
XconCcmFailure Frame	Displays the frame that caused the XconCCMFailure
Mep Loopback Information
LbRxReply	Displays the number of received loopback (LB) replies
LbRxBadOrder	Displays the number of received loopback messages that are in a bad order
LbRxBadMsdu	Displays the number of loopback replies that have been received with the wrong destination MAC address (MSDU = MAC Service Data Unit)
LbTxReply	Displays the number of loopback replies transmitted out this MEP
LbTxReply (Total)	Displays the total number of LBRs (loopback replies) transmitted from this MEP
LbTxReplyNoTLV	Displays the number of LBRs (loopback replies) transmitted from this MEP with no TLV. Because only LBMs with no TLVs are used for throughput testing, the LbTxReply (Total), LbTxReplyNoTLV, and LbTxReplyWithTLV counters can help debug problems if throughput testing is not working
LbTxReplyWithTLV	Displays the number of LBRs (loopback replies) transmitted from this MEP with TLV
LbSequence	Displays the sequence number in the loopback message
LbNextSequence	Displays the next loopback sequence
LbStatus	Displays the loopback status as True or False: True — loopback is in progress False — no loopback is in progress
LbResultOk	Displays the result of the loopback test
DestIsMepId	Identifies whether the destination interface has a MEP-ID (true or false)
DestMepId	Displays the MEP-ID of the destination interface
DestMac	Displays the MAC address of the destination interface
SendCount	Indicates the number of loopback messages sent
VlanDropEnable	Identifies whether the VLAN drop is enabled (true or false)
VlanPriority	Displays the VLAN priority
Data TLV	Displays the data TLV information
Mep Linktrace Message Information
LtRxUnexplained	Displays the number of unexplained linktrace messages (LTM) that have been received
LtNextSequence	Displays the sequence number of the next linktrace message
LtStatus	Displays the status of the linktrace
LtResult	Displays the result of the linktrace
TargIsMepId	Identifies whether the target interface has a MEP-ID (true or false)
TargMepId	Displays the MEP-ID of the target interface
TargMac	Displays the MAC address of the target interface
TTL	Displays the TTL value
EgressId	Displays the egress ID of the linktrace message
SequenceNum	Displays the sequence number of the linktrace message
LtFlags	Displays the linktrace flags
Mep Linktrace Replies
SequenceNum	Displays the sequence number returned by a previous transmit linktrace message, indicating which linktrace message response is returned
ReceiveOrder	Displays the order in which the linktrace initiator received the linktrace replies
Ttl	Displays the TTL field value for a returned linktrace reply
Forwarded	Indicates whether the linktrace message was forwarded by the responding MEP
LastEgressId	Displays the last egress identifier returned in the linktrace reply egress identifier TLV of the linktrace reply The last egress identifier identifies the MEP linktrace initiator that initiated, or the linktrace responder that forwarded, the linktrace message for which this linktrace reply is the response. This is the same value as the egress identifier TLV of that linktrace message.
TerminalMep	Indicates whether the forwarded linktrace message reached a MEP enclosing its MA
NextEgressId	Displays the next egress identifier returned in the linktrace reply egress identifier TLV of the linktrace reply. The next egress identifier identifies the linktrace responder that transmitted this linktrace reply and can forward the linktrace message to the next hop. This is the same value as the egress identifier TLV of the forwarded linktrace message, if any.
Relay	Displays the value returned in the Relay Action field
ChassisIdSubType	Displays the format of the chassis ID returned in the Sender ID TLV of the linktrace reply, if any. This value is meaningless if the chassis ID has a length of 0
ChassisId	Displays the chassis ID returned in the Sender ID TLV of the linktrace reply, if any. The format is determined by the value of the ChassisIdSubType.
ManAddressDomain	Displays the TDomain that identifies the type and format of the related ManAddress, used to access the SNMP agent of the system transmitting the linktrace reply Received in the linktrace reply Sender ID TLV from that system
ManAddress	Displays the TAddress that can be used to access the SNMP agent of the system transmitting the CCM Received in the CCM Sender ID TLV from that system
IngressMac	Displays the MAC address returned in the ingress MAC address field
Ingress Action	Displays the value returned in the Ingress Action field of the linktrace message
IngressPortIdSubType	Displays the format of the ingress port ID
IngressPortId	Displays the ingress port ID; the format is determined by the value of the IngressPortIdSubType
EgressMac	Displays the MAC address returned in the egress MAC address field
Egress Action	Displays the value returned in the Egress Action field of the linktrace message
EgressPortIdSubType	Displays the format of the egress port ID
EgressPortId	Displays the egress port ID; the format is determined by the value of the EgressPortIDSubType
Org Specific TLV	Displays all organization-specific TLVs returned in the linktrace reply, if any Includes all octets including and following the TLV length field of each TLV, concatenated
Eth-Test
Peer Mac Addr	Displays the MAC address of the peer (remote) entity
FrameCount	Displays the number of test frames sent between the MEP and the peer entity
ByteCount	Displays the number of bytes sent between the MEP and the peer entity
Current ErrBits	Displays the number of bit errors in the current test
Current CrcErrs	Displays the number of CRC errors in the current test
Accumulate ErrBits	Displays the accumulated number of bit errors in the current test
Accumulate CrcErrs	Displays the accumulated number of CRC errors in the current test
Delay Measurement Test
Peer Mac Addr	Displays the MAC address of the peer (remote) entity
Delay (us)	Displays the measured delay (in microseconds) for the DM test
Delay Variation (us)	Displays the measured delay variation (in microseconds) for the DV test

Sample output 2

A:Dut-A>config>port>ethernet# show eth-cfm mep 1 domain 1 association 1 eth-
bandwidth-notification 
===============================================================================
Eth-Cfm MEP Configuration Information
===============================================================================
Md-index         : 1                        Direction         : Down
Ma-index         : 1                        Admin             : Enabled
MepId            : 1                        CCM-Enable        : Enabled
Port             : 1/1/5                    VLAN              : 0
Description      : (Not Specified)
FngAlarmTime     : 0                        FngResetTime      : 0
FngState         : fngReset                 ControlMep        : False
LowestDefectPri  : macRemErrXcon            HighestDefect     : none
Defect Flags     : None
Mac Address      : d0:99:d5:80:51:a6        
                                            CcmPaddingSize    : 0 octets
CcmTx            : 169                      CcmSequenceErr    : 0
CcmIgnoreTLVs    : (Not Specified)
Fault Propagation: disabled                 
MA-CcmInterval   : 1                        MA-CcmHoldTime    : 0ms
MA-Primary-Vid   : Disabled                 
                                            MD-Level          : 0
Eth-Ais          : Disabled                 
Eth-Ais Tx defCCM: allDef                   
Eth-BNM Receive  : Enabled                  Eth-BNM Rx Pacing : 5
Redundancy:
    MC-LAG State : n/a                      
CcmLastFailure Frame:
    None
XconCcmFailure Frame:
    None

Table: Output fields: MEP ETH-BN
Label	Description
Md-index	Displays the MD index of the domain
Direction	Displays the direction of OAM PDU transmission
Ma-index	Displays the MA index of the association
Admin	Displays the administrative status of the MEP
MepId	Displays the MEP ID
CCM-Enable	Displays the status of the CCM (enabled or disabled)
Port	Displays the port number
VLAN	Displays the configured VLAN on the MEP
Description	Displays the description
FngAlarmTime	Displays the fault alarm time
FngResetTime	Displays the fault alarm reset time
FngState	Displays the different states of the Fault Notification Generator
LowestDefectPri	Displays the lowest priority defect (a configured value) that is allowed to generate a fault alarm
HighestDefect	Displays the highest defect that is present (for example, if defRDICCM and defXconCCM are present, the highest defect is defXconCCM)
Defect Flags	Displays the number of defect flags
Mac Address	Displays the MAC address of the MEP
CcmTx	Displays the total number of CCM transmitted
CcmPaddingSize	Displays the number of octets used to pad a CCM packet
CcmSequenceErr	Displays the total number of out-of-sequence CCMs received
Fault Propagation	Displays the fault propagation configuration for the MEP
MA-CcmInterval	Displays the CCM transmission interval for all MEPs in the association
MA-CcmHoldTime	Displays the CCM hold time for all MEPs in the association
MD-Level	Displays the MD level
Eth-Ais	Displays the state of the ETH-AIS test (enabled or disabled)
Eth-BNM Receive	Displays whether ETH-BN receive is enabled or disabled
Eth-BNM Rx Pacing	Displays the ETH-BN receive update pacing interval time
MC-LAG State	Displays the MC-LAG state
CcmLastFailure Frame	Displays the frame that caused the last CCM failure
XconCcmFailure Frame	Displays the frame that caused the XconCCMFailure

mip

Syntax

mip

Context

show>eth-cfm

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

This command displays SAPs/bindings provisioned for allowing the default MIP creation.

Output

The following output is an example of MIP information.

Sample output

*A:node-1# show eth-cfm mip
==========================================================================
CFM SAP MIP Table
==========================================================================
Sap Mip-Enabled Mip Mac Address
--------------------------------------------------------------------------
1/1/1:1.1 yes Not Configured
==========================================================================
==========================================================================
CFM SDP MIP Table
==========================================================================
Sdp Mip-Enabled Mip Mac Address
--------------------------------------------------------------------------
No Matching Entries

statistics

Syntax

statistics

Context

show>eth-cfm

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

This command displays the ETH-CFM statistics counters.

Output

The following output is an example of ETH-CFM statistics information.

Sample output

# show eth-cfm system-config
===============================================================================
CFM System Configuration
===============================================================================
Redundancy
MC-LAG Standby MEP Shutdown: true
MC-LAG Hold-Timer : 1 second(s)
Synthetic Loss Measurement
Inactivity Timer : 100 second(s)
===============================================================================

system-config

Syntax

system-config

Context

show>eth-cfm

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

This command shows various system level configuration parameters. These global eth-cfm commands are those which are configured directly under the config>eth-cfm context.

Output

The following output is an example of ETH-CFM system configuration information.

Sample output

# show eth-cfm system-config
===============================================================================
CFM System Configuration
===============================================================================
Redundancy
MC-LAG Standby MEP Shutdown: true
MC-LAG Hold-Timer : 1 second(s)
Synthetic Loss Measurement
Inactivity Timer : 100 second(s)
===============================================================================

ldp-treetrace

Syntax

ldp-treetrace [prefix ip-prefix/mask] [detail]

Context

show>test-oam

Platforms

7210 SAS-T, 7210 SAS-Mxp, 7210 SAS-Sx/S 1/10GE (standalone and standalone-VC), 7210 SAS-Sx 10/100GE, 7210 SAS-R6, and 7210 SAS-R12

Description

This command displays OAM LDP treetrace information.

Parameters

prefix ip-prefix/mask: Specifies the address prefix and subnet mask of the destination node.

detail: Displays detailed information.

Output

The following output is an example of OAM LDP treetrace information.

Sample output

*A:ALA-48# show test-oam ldp-treetrace
Admin State              : Up             Discovery State      : Done          
Discovery-intvl (min)    : 60             Probe-intvl (min)    : 2             
Probe-timeout (min)      : 1              Probe-retry          : 3             
Trace-timeout (sec)      : 60             Trace-retry          : 3             
Max-TTL                  : 30             Max-path             : 128           
Forwarding-class (fc)    : be             Profile              : Out           
Total Fecs               : 400            Discovered Fecs      : 400           
Last Discovery Start     : 12/19/2006 05:10:14                                 
Last Discovery End       : 12/19/2006 05:12:02                                 
Last Discovery Duration  : 00h01m48s                                           
Policy1                  : policy-1                                            
Policy2                  : policy-2 

*A:ALA-48# show test-oam ldp-treetrace detail
Admin State              : Up             Discovery State      : Done          
Discovery-intvl (min)    : 60             Probe-intvl (min)    : 2             
Probe-timeout (min)      : 1              Probe-retry          : 3             
Trace-timeout (sec)      : 60             Trace-retry          : 3             
Max-TTL                  : 30             Max-path             : 128           
Forwarding-class (fc)    : be             Profile              : Out           
Total Fecs               : 400            Discovered Fecs      : 400           
Last Discovery Start     : 12/19/2006 05:10:14                                 
Last Discovery End       : 12/19/2006 05:12:02                                 
Last Discovery Duration  : 00h01m48s                                           
Policy1                  : policy-1                                            
Policy2                  : policy-2 
===============================================================================
Prefix (FEC) Info
===============================================================================
Prefix              Path Last                  Probe  Discov    Discov         
                    Num  Discovered            State  State     Status         
-------------------------------------------------------------------------------
10.11.11.1/32       54   12/19/2006 05:10:15   OK     Done      OK             
10.11.11.2/32       54   12/19/2006 05:10:15   OK     Done      OK             
10.11.11.3/32       54   12/19/2006 05:10:15   OK     Done      OK 
………… 
10.14.14.95/32      72   12/19/2006 05:11:13   OK     Done      OK             
10.14.14.96/32      72   12/19/2006 05:11:13   OK     Done      OK             
10.14.14.97/32      72   12/19/2006 05:11:15   OK     Done      OK             
10.14.14.98/32      72   12/19/2006 05:11:15   OK     Done      OK             
10.14.14.99/32      72   12/19/2006 05:11:18   OK     Done      OK             
10.14.14.100/32     72   12/19/2006 05:11:20   OK     Done      OK             
===============================================================================
Legend: uP - unexplored paths, tO - trace request timed out
        mH - max hop exceeded, mP - max path exceeded
        nR - no internal resource


*A:ALA-48# show test-oam ldp-treetrace prefix 10.12.12.10/32
Discovery State  : Done                 Last Discovered  : 12/19/2006 05:11:02 
Discovery Status : ' OK '                                                    
Discovered Paths : 54                   Failed Hops      : 0                   
Probe State      : OK                   Failed Probes    : 0 


*A:ALA-48# show test-oam ldp-treetrace prefix 10.12.12.10/32  detail 
Discovery State  : Done                 Last Discovered  : 12/19/2006 05:11:02 
Discovery Status : ' OK '                                                    
Discovered Paths : 54                   Failed Hops      : 0                   
Probe State      : OK                   Failed Probes    : 0 
===============================================================================
Discovered Paths
===============================================================================
PathDest            Egr-NextHop         Remote-RtrAddr      Discovery-time     
  DiscoveryTtl        ProbeState          ProbeTmOutCnt       RtnCode          
-------------------------------------------------------------------------------
127.1.0.5           10.10.1.2           10.12.12.10         12/19/2006 05:11:01
              7     OK                  0                   EgressRtr          
127.1.0.9           10.10.1.2           10.12.12.10         12/19/2006 05:11:01
              7     OK                  0                   EgressRtr          
127.1.0.15          10.10.1.2           10.12.12.10         12/19/2006 05:11:01
              7     OK                  0                   EgressRtr          
127.1.0.19          10.10.1.2           10.12.12.10         12/19/2006 05:11:01
              7     OK                  0                   EgressRtr          
127.1.0.24          10.10.1.2           10.12.12.10         12/19/2006 05:11:01
              7     OK                  0                   EgressRtr          
127.1.0.28          10.10.1.2           10.12.12.10         12/19/2006 05:11:01

……………..

127.1.0.252         10.10.1.2           10.12.12.10         12/19/2006 05:11:01
              7     OK                  0                   EgressRtr          
127.1.0.255         10.10.1.2           10.12.12.10         12/19/2006 05:11:01
              7     OK                  0                   EgressRtr          
===============================================================================
*A:ALA-48#

twamp

Syntax

twamp

Context

show>test-oam

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

Commands in this context request TWAMP information.

twamp-light

Syntax

twamp-light

Context

show>test-oam>twamp

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

Commands in this context request TWAMP Light information.

reflectors

Syntax

reflectors

Context

show>test-oam>twamp>twamp-light

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

This command displays TWAMP Light reflector information.

Output

The following output is an example of OAM TWAMP light information, and Table: Output fields: TWAMP Light reflectors describes the output fields.

Sample output

show test-oam twamp twamp-light reflectors
=======================================================================
TWAMP-Light Reflectors
=======================================================================
Router/VPRN    Admin    UDP Port    Prefixes    Frames Rx    Frames Tx
-----------------------------------------------------------------------
Base              Up       15000           1            0            0
500               Up       15000           2         6340         6340
-----------------------------------------------------------------------
No. of TWAMP-Light Reflectors: 2
=======================================================================

Table: Output fields: TWAMP Light reflectors
Label	Description
TWAMP Light Reflector
Router/VPRN	The TWAMP Light clients
Admin	Displays one of the following: Up—the server or prefix is administratively enabled (no shutdown) in configuration Down—the server or prefix is administratively disabled (shutdown) in configuration
UDP Port	The UDP port number used
Prefixes	The time since the server process was started, measured in days (d), hours, minutes, and seconds
Frames Rx	The total number of frames received from session senders
Frames Tx	The total number of frames sent to session senders

server

Syntax

server all

server prefix ip-prefix/mask

server

Context

show>test-oam>twamp

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

This command displays information about the TWAMP server. It displays summary information for the ip-prefix in use.

Parameters

all: Specifies to display all information about the TWAMP server.

ip-prefix/mask

Specifies the destination address of the static route and the prefix length.

Values

ip-prefix/mask	ipv4-prefix	a.b.c.d (host bits must be 0)
	ipv4-prefix-le	[0 to 32]
	ipv6-prefix	x:x:x:x:x:x:x:x: (eight 16-bit pieces)
		x:x:x:x:x:x:d.d.d.d
		x - [0 to FFFF]H
		d - [0 to 255]D
	ipv6-prefix-le	[0 to 128]

Output

The following outputs are examples of TWAMP server information, and Table: Output fields: TWAMP server describes the output fields.

Sample output

*A:Dut-G>show>test-oam# twamp server

===============================================================================
TWAMP Server
===============================================================================
Admin State          : Down                Operational State   : Down
Up Time              : 0d 00:00:00
Current Connections  : 0                   Max Connections     : 8
Connections Rejected : 0                   Inactivity Time Out : 900 seconds
Current Sessions     : 0                   Max Sessions        : 8
Sessions Rejected    : 0                   Sessions Aborted    : 0
Sessions Completed   : 0
Test Packets Rx      : 0                   Test Packets Tx     : 0
===============================================================================

===============================================================================
TWAMP Server Prefix Summary
===============================================================================
Prefix             Current     Current  Description
                   Connections Sessions
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
No. of TWAMP Server Prefixes: 0
===============================================================================
*A:Dut-G>show>test-oam#

Sample output: all

The following output is an example of all TWAMP server information.

7210SAS# show  test-oam twamp server all

===============================================================================
TWAMP Server
===============================================================================
Admin State          : Up                  Operational State   : Up
Up Time              : 0d 08:17:34
Current Connections  : 0                   Max Connections     : 16
Connections Rejected : 0                   Inactivity Time Out : 900 seconds
Current Sessions     : 0                   Max Sessions        : 16
Sessions Rejected    : 0                   Sessions Aborted    : 0
Sessions Completed   : 0
Test Packets Rx      : 0                   Test Packets Tx     : 0
===============================================================================

===============================================================================
TWAMP Server Prefix 10.1.1.0/24
===============================================================================
Description          : (Not Specified)
Current Connections  : 0                   Max Connections     : 16
Connections Rejected : 0
Current Sessions     : 0                   Max Sessions        : 16
Sessions Rejected    : 0                   Sessions Aborted    : 0
Sessions Completed   : 0
Test Packets Rx      : 0                   Test Packets Tx     : 0
===============================================================================

===============================================================================
Connection information for TWAMP server prefix 10.1.1.0/24
===============================================================================
Client          State      Curr Sessions  Sessions Rejected  Sessions Completed
                           Idle Time (s)    Test Packets Rx     Test Packets Tx
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
No. of TWAMP Server Connections for Prefix 10.1.1.0/24: 0
===============================================================================

===============================================================================
TWAMP Server Prefix 10.1.1.0/24
===============================================================================
Description          : (Not Specified)
Current Connections  : 0                   Max Connections     : 16
Connections Rejected : 0
Current Sessions     : 0                   Max Sessions        : 16
Sessions Rejected    : 0                   Sessions Aborted    : 0
Sessions Completed   : 0
Test Packets Rx      : 0                   Test Packets Tx     : 0
===============================================================================

===============================================================================
Connection information for TWAMP server prefix 10.1.1.0/24
===============================================================================
Client          State      Curr Sessions  Sessions Rejected  Sessions Completed
                           Idle Time (s)    Test Packets Rx     Test Packets Tx
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
No. of TWAMP Server Connections for Prefix 10.1.1.0/24: 0
===============================================================================
===============================================================================
No. of TWAMP Server Prefixes: 2
===============================================================================

Sample output: prefix

The following output is an example of TWAMP server prefix information.

*A:7210SAS# show test-oam twamp server  prefix 10.1.1.0/24

===============================================================================
TWAMP Server Prefix 10.1.1.0/24
===============================================================================
Description          : (Not Specified)
Current Connections  : 0                   Max Connections     : 16
Connections Rejected : 0
Current Sessions     : 0                   Max Sessions        : 16
Sessions Rejected    : 0                   Sessions Aborted    : 0
Sessions Completed   : 0
Test Packets Rx      : 0                   Test Packets Tx     : 0
===============================================================================

===============================================================================
Connection information for TWAMP server prefix 10.1.1.0/24
===============================================================================
Client          State      Curr Sessions  Sessions Rejected  Sessions Completed
                           Idle Time (s)    Test Packets Rx     Test Packets Tx
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
No. of TWAMP Server Connections for Prefix 10.1.1.0/24: 0
===============================================================================

Table: Output fields: TWAMP server
Label	Description
Admin State	Displays one of the following: Up — The server or prefix is administratively enabled (no shutdown) in configuration. Down — The server or prefix is administratively disabled (shutdown) in configuration.
Operational State	Displays one of the following: Up — The server or prefix is operationally enabled. Down — The server or prefix is operationally disabled.
Up Time	Displays the time since the server process was started, measured in days (d), hours, minutes, and seconds.
Current Connections	Displays the total number of currently connected clients.
Max Connections	Displays the maximum number of connected clients.
Connections Rejected	Displays the number of connection rejections.
Inactivity Timeout	Displays the configured inactivity timeout for all TWAMP-control connections (inactivity-timeout).
Current Sessions	Displays the number of current sessions.
Max Sessions	Displays the maximum number of sessions.
Sessions Rejected	Displays the number of rejected sessions for the TWAMP client.
Sessions Aborted	Displays the number of manually aborted sessions for the TWAMP client.
Sessions Completed	Displays the number of completed sessions for the TWAMP client.
Test Packets Rx	Displays the number of test packets received.
Test Packets Tx	Displays the number of test packets transmitted.
Description	Displays the configured description of the TWAMP server.
Connection information for TWAMP server prefix	Displays the IP address prefix of a TWAMP server.
Client	Displays the IP address of the TWAMP client.
State	Displays the operational state of the TWAMP client.
Curr Sessions	Displays the number of current sessions for the TWAMP client.
Idle Time (s)	Displays the total idle time, in seconds, of the TWAMP client.
No. of Conns for Prefix	Displays the total number of connections for the TWAMP server with the displayed IP address prefix.
No. of TWAMP Server Prefixes	Displays the total number of displayed TWAMP server IP address prefixes.

testhead-profile

Syntax

testhead-profile profile-id

Context

show>test-oam

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

This command specifies the testhead profile ID to use with this run or session of testhead invocation. The testhead profile must be configure before using the commands under config> test-oam> testhead-profile context.

Output

The following output is an example of testhead profile information, and Table: Output fields: test OAM testhead profile describes the output fields.

Sample output

*A:7210SAS>config>test-oam># show test-oam testhead-profile 1 

===============================================================================
Y.1564 Testhead Profile
===============================================================================
Description        : Testhead_Profile_1
Profile Id         : 1                        Frame Size        : 512
CIR Configured     : 100                      CIR Operational   : 96
PIR Configured     : 200                      PIR Operational   : 200
CIR Rule           : max                      Ref. Count        : 0
InPrf Dot1p        : 2                        OutPrf Dot1p      : 4
Duration Hrs       : 0                        
Duration Mins      : 3                        
Duration Secs      : 0                        

-------------------------------------------------------------------------------
Acceptance Criteria Id 1
-------------------------------------------------------------------------------
Loss TH            : 0.000100                 Jitter TH         : 100
InProf Loss TH     : 0.000100                 InProf Jitter TH  : 100
OutProf Loss TH    : 0.000100                 OutProf Jitter TH : 100

Latency TH         : 100                      Ref. Count        : 0
InProf Latency TH  : 100                      CIR TH            : 1000
OutProf Latency TH : 100                      PIR TH            : 200

-------------------------------------------------------------------------------
Frame Payload Id 1
-------------------------------------------------------------------------------
Payload Type       : tcp-ipv4
Description        : Frame_Payload_1
Dst Mac            : 00:00:00:00:00:02        
Src Mac            : 00:00:00:00:00:01        
Vlan Tag 1         : Not configured           
Vlan Tag 2         : Not configured           
Ethertype          : 0x0800                   DSCP              : af11
TOS                : 8                        TTL               : 64
Src. IP            : 10.1.1.1                 Dst. IP           : 10.2.2.2
L4 Dst Port        : 50                       L4 Src Port       : 40
Protocol           : 6                        Ref. Count        : 0
Data Pattern       : a1b2c3d4e5f6
===============================================================================
*A:7210SAS>config>test-oam>#

Table: Output fields: test OAM testhead profile
Label	Description
`Description`	Displays the description configured by the user for the test.
`Profile Id`	Displays the profile identifier.
`CIR Configured`	Displays the value of the CIR configured.
`PIR Configured`	Displays the value of the PIR configured.
`Frame Size`	Displays the size of the frame.
`CIR Operational`	Displays the value of the CIR operational rate configured.
`PIR Operational`	Displays the value of the PIR operational rate configured.
`CIR Rule`	Displays the adaptation rule configured by the user.
`InPrf Dot1p`	Displays the dot1p value used to identify green or in-profile packets.
`Ref. Count`	Displays the total number of testhead (completed or running) sessions pointing to a profile or acceptance criteria or a frame payload.
`OutPrf Dot1p`	Displays the dot1p value used to identify green or out-of-profile packets.
`Duration Hrs, mins, and secs`	Displays the test duration in hours, minutes, and seconds.
`Loss TH`	Displays the user configured loss threshold value for comparison with measured value.
`Jitter TH`	Displays the user configured jitter threshold value for comparison with measured value.
`InProf Loss TH`	Displays the user configured in-profile loss threshold value for comparison with measured value.
`OutProf Loss TH`	Displays the user configured out-of-profile loss threshold value for comparison with measured value.
`Latency TH`	Displays the user configured latency threshold value for comparison with measured value.
`InProf Latency TH`	Displays the user configured in-profile latency threshold value for comparison with measured value.
`OutProf Latency TH`	Displays the user configured out-of-profile latency threshold value for comparison with measured value.
`InProf Jitter TH`	Displays the user configured in-profile jitter threshold value for comparison with measured value.
`OutProf Jitter TH`	Displays the user configured out-of-profile jitter threshold value for comparison with measured value.
`CIR TH`	Displays the user configured CIR threshold value for comparison with measured value.
`PIR TH`	Displays the user configured PIR threshold value for comparison with measured value.
`Payload Type`	Identifies the type of the payload.
`Dst Mac`	Displays the value of destination MAC configured by the user to use in the frame generated by the testhead tool
`Src Mac`	Displays the value of source MAC configured by the user to use in the frame generated by the testhead tool
`Vlan Tag 1`	Displays the values of the outermost vlan-tag configured by the user to use in the frame generated by the testhead tool.
`Vlan Tag 2`	Displays the values of the second vlan-tag configured by the user to use in the frame generated by the testhead tool.
`Ethertype`	Displays the values of the ethertype configured by the user to use in the frame generated by the testhead tool.
`TOS`	Displays the values of the IP TOS (Type of Service) configured by the user to use in the frame generated by the testhead tool.
`Src. IP`	Displays the values of the source IPv4 address configured by the user to use in the frame generated by the testhead tool.
`L4 Dst Port`	Displays the values of the TCP header configured by the user to use in the frame generated by the testhead tool.
`Protocol`	Displays the values of the IP protocol value configured by the user to use in the frame generated by the testhead tool.
`Data Pattern`	Displays the values of the data pattern configured by the user to use in the frame generated by the testhead tool.
`DSCP`	Displays the values of the DSCP configured by the user to use in the frame generated by the testhead tool.
`TTL`	Displays the values of the IP TTL (Time-to-Live) value configured by the user to use in the frame generated by the testhead tool.
`Dst. IP`	Displays the values of the destination IPv4 address configured by the user to use in the frame generated by the testhead tool.
`L4 Src Port`	Displays the values of the source port configured by the user to use in the frame generated by the testhead tool.

testhead

Syntax

testhead test-name owner test-owner

Context

show

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

This command displays the testhead test identified by the test name and owner.

Parameters

test-name: Name of the SAA test. The test name must already be configured in the config>saa>test context.

owner test-owner

Specifies the owner of an SAA operation up to 32 characters.

Default: If a test-owner value is not specified, tests created by the CLI have a default owner ‟TiMOS CLI”.

Output

The following output is an example of testhead information, and Table: Output fields: testhead describes the output fields.

Sample output

*A:7210SAS# show testhead test-me  owner owner-me 

===============================================================================
Y.1564 Testhead Session
===============================================================================
Owner              : owner-me
Test               : test-me
Profile Id         : 1                        SAP               : 1/1/2:100
Accept. Crit. Id   : 0                        Completed         : Yes
Frame Payload Id   : 1                        Stopped           : No
Frame Payload Type : tcp-ipv4                 FC                : be
Color Aware Test   : Yes                      
Start Time         : 08/08/2001 19:37:11      
End Time           : 08/08/2001 19:40:16      
Total time taken   : 0d 00:03:05              

-------------------------------------------------------------------------------
Latency Results
-------------------------------------------------------------------------------
 (total pkts in us):       Min       Max   Average    Jitter
         Roundtrip :         0         0         0         0

(OutPrf pkts in us):       Min       Max   Average    Jitter
         Roundtrip :         0         0         0         0

 (InPrf pkts in us):       Min       Max   Average    Jitter
         Roundtrip :         0         0         0         0

-------------------------------------------------------------------------------
Packet Count
-------------------------------------------------------------------------------
Total Injected     : 42273637                 
Total Received     : 0                        

OutPrf Injected    : 16898179                 
OutPrf Received    : 0                        

InPrf Injected     : 25375450                 
InPrf Received     : 0                        

-------------------------------------------------------------------------------
Test Compliance Report
-------------------------------------------------------------------------------
Throughput Configd : 962388                   
Throughput Oper    : 962384                   
Throughput Measurd : 0                        

PIR Tput Threshld  : Not configured           
PIR Tput Meas      : 0                        

CIR Tput Threshld  : Not configured           
CIR Tput Meas      : 0                        

FLR Configured     : None                     
FLR Measurd        : Not Applicable           
FLR Acceptance     : Fail                     

OutPrf FLR Conf    : None                     
OutPrf FLR Meas    : Not Applicable           
OutPrf FLR Acep    : Not Applicable           

InPrf FLR Conf     : None                     
InPrf FLR Meas     : Not Applicable           
InPrf FLR Acep     : Not Applicable           

Latency Configd(us): None                     
Latency Measurd(us): None                     
Latency Acceptance : Not Applicable           

OutPrf Lat Conf(us): None                     
OutPrf Lat Meas(us): None                     
OutPrf Lat Acep    : Not Applicable           

InPrf Lat Conf(us) : None                     
InPrf Lat Meas(us) : None                     
InPrf Lat Acep     : Not Applicable           

Jitter Configd(us) : None                     
Jitter Measurd(us) : None                     
Jitter Acceptance  : Not Applicable           

OutPrf Jit Conf(us): None                     
OutPrf Jit Meas(us): None                     
OutPrf Jit Acep    : Not Applicable           

InPrf Jit Conf(us) : None                     
InPrf Jit Meas(us) : None                     
InPrf Jit Acep     : Not Applicable           

Total Pkts. Tx.    : 13                       Latency Pkts. Tx. : 8
OutPrf Latency Pkt*: 0                        InPrf Latency Pkt*: 0
Total Tx. Fail     : 0 =============================================================
==================
*A:7210SAS# show testhead test-me  owner owner-me

Table: Output fields: testhead
Label	Description
`Owner`	Displays the owner of the test.
`Name`	Displays the name of the test.
`Description`	Displays the description for the test type.
`Profile Id`	Displays the associated profile ID.
`Accept. Crit. Id`	Displays the test acceptance criteria ID to be used by the testhead OAM tool to declare the PASS/FAIL result at the completion of the test.
`Frame Payload Id`	Displays frame payload ID, that determines the frame content of the frames generated by the tool.
`Frame Payload Type`	Displays the type of frame payload to be used in frames generated by testhead tool.
`Color Aware Test`	Displays if color aware tests need to be executed.
`SAP`	Displays the SAP ID configured.
`Completed`	Displays if the test has been completed.
`Stopped`	Displays if the test has been stopped.
`FC`	Displays the forwarding class (FC) to use to send the frames generated by the testhead tool.
`Start Time`	Displays the start time of the test.
`End Time`	Displays the end time of the test.
`Total time taken`	Displays the total time taken to execute the test.
`total pkts in us`	Displays the total packets in microseconds.
`OutPrf pkts in us`	Displays the out-of-profile packets in microseconds.
`InPrf pkts in us`	Displays the in-profile packets in microseconds.
`Total Injected`	Displays the running count of total injected packets, including marker packets.
`Total Received`	Displays the running count of total received packets, including marker packets.
`OutPrf Injected`	Displays the running count of total out-of-profile packets, excluding marker packets.
`OutPrf Received`	Displays the running count of total out-of-profile packets received, including marker packets.
`InPrf Injected`	Displays the running count of total in-profile packets, excluding marker packets.
`InPrf Received`	Displays the running count of total in-profile packets received, including marker packets.
`Throughput Configd`	Displays the CIR Throughput rate Threshold Configured (in Kbps).
`Throughput Oper`	Displays the operational rate used for the configured rate. Operational rate is arrived considering the adaptation rule configured by the user and supported hardware rate.
`Throughput Measurd`	Displays the CIR Throughput Measured Value (in Kbps).
`PIR Tput Threshld`	Displays the PIR Throughput rate Threshold Configured (in Kbps).
`PIR Tput Meas`	Displays the PIR Throughput rate Measured Value (in Kbps).
`FLR Configured`	Displays the Frame Loss Ratio Threshold Configured (in-profile).
`FLR Measurd`	Displays the Frame Loss Ratio Measured (in-profile).
`FLR Acceptance`	Displays Pass, Fail, or Not Applicable. It displays Pass, if the measured value is less than or equal to the configured threshold and displays "Fail" otherwise, and displays "Not Applicable", if the FLR criteria is not used to determine whether the test is in Passed or Failed status.
`OutPrf FLR Conf`	Displays the out-of-profile Frame Loss Ratio configured.
`OutPrf FLR Meas`	Displays the out-of-profile Frame Loss Ratio measured.
`OutPrf FLR Acep`	Displays Pass, Fail, or Not Applicable. It displays Pass, if the measured value is less than or equal to the configured threshold and displays "Fail" otherwise, and displays "Not Applicable", if the out-of-profile FLR criteria is not used to determine whether the test is in Passed or Failed status.
`InPrf FLR Conf`	Displays the in-profile Frame Loss Ratio configured.
`InPrf FLR Meas`	Displays the in-profile Frame Loss Ratio measured.
`InPrf FLR Acep`	Displays Pass, Fail, or Not Applicable. It displays Pass, if the measured value is less than or equal to the configured threshold and displays "Fail" otherwise, and displays "Not Applicable", if the in-profile FLR criteria is not used to determine whether the test is in Passed or Failed status.
`Latency Configd(us)`	Displays the Latency Threshold configured (in microseconds)
`Latency Measurd(us)`	Displays the Average Latency measured (in microseconds)
`Latency Acceptance`	Displays Pass, Fail, or Not Applicable. It displays Pass, if the measured value is less than or equal to the configured threshold and displays "Fail" otherwise, and displays "Not Applicable", if the latency criteria is not used to determine whether the test is in Passed or Failed status.
`OutPrf Lat Conf(us)`	Displays the out-of-profile latency configured.
`OutPrf Lat Meas(us)`	Displays the out-of-profile latency measured.
`OutPrf Lat Acep`	Displays Pass, Fail, or Not Applicable. It displays Pass, if the measured value is less than or equal to the configured threshold and displays "Fail" otherwise, and displays "Not Applicable", if the out-of-profile latency criteria is not used to determine whether the test is in Passed or Failed status.
`InPrf Lat Conf(us)`	Displays the in-profile latency configured.
`InPrf Lat Meas(us)`	Displays the in-profile latency measured.
`InPrf Lat Acep`	Displays Pass, Fail, or Not Applicable. It displays Pass, if the measured value is less than or equal to the configured threshold and displays "Fail" otherwise, and displays "Not Applicable", if the in-profile latency criteria is not used to determine whether the test is in Passed or Failed status.
`Jitter Configd(us)`	Displays the Jitter Threshold Configured (in microseconds).
`Jitter Measurd(us)`	Displays the Jitter Measured (in microseconds).
`Jitter Acceptance`	Displays Pass, Fail, or Not Applicable. It displays Pass, if the measured value is less than or equal to the configured threshold and displays "Fail" otherwise, and displays "Not Applicable", if the jitter criteria is not used to determine whether the test is in Passed or Failed status.
`OutPrf Jit Conf(us)`	Displays the out-of-profile Jitter configured.
`OutPrf Jit Meas(us)`	Displays the out-of-profile Jitter measured.
`OutPrf Jit Acep`	Displays Pass, Fail, or Not Applicable. It displays Pass, if the measured value is less than or equal to the configured threshold and displays "Fail" otherwise, and displays "Not Applicable", if the out-of-profile jitter criteria is not used to determine whether the test is in Passed or Failed status.
`InPrf Jit Conf(us)`	Displays the in-profile Jitter configured.
`InPrf Jit Meas(us)`	Displays the in-profile Jitter measured.
`InPrf Jit Acep`	Displays Pass, Fail, or Not Applicable. It displays Pass, if the measured value is less than or equal to the configured threshold and displays "Fail" otherwise, and displays "Not Applicable", if the in-profile jitter criteria is not used to determine whether the test is in Passed or Failed status.
`Total Pkts. Tx.`	Displays the total number of packets (that is, data and marker) transmitted by the testhead session for the duration of the test.
`OutPrf Latency Pkt*`	Displays the total number of out-of-profile marker packets received by the testhead session for the duration of the test.
`Total Tx. Fail`	Displays the total number of failed transmission attempts by the testhead session for the duration of the test.
`Latency Pkts. Tx`	Displays the total number of marker packets transmitted by the testhead session for the duration of the test.
`InPrf Latency Pkt*`	Displays the total number of in-profile marker packets received by the testhead session for the duration of the test.

bin-group

Syntax

bin-group [bin-group-number]

Context

show>oam-pm

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

This command displays data for one or all OAM-PM bin groups.

Parameters

bin-group-number

Specifies an OAM-PM bin group.

Values: 1 to 255

Output

The following output is an example of OAM-PM bin group information.

Sample output

show oam-pm bin-group
-------------------------------------------------------------------------------
Configured Lower Bounds for Delay Measurement (DMM) Tests, in microseconds
-------------------------------------------------------------------------------
Group Description                    Admin Bin     FD(us)    FDR(us)   IFDV(us)
-------------------------------------------------------------------------------
1     OAM PM default bin group (not*    Up   0          0          0          0
                                             1       5000       5000       5000
                                             2      10000          -          -
-------------------------------------------------------------------------------
2                                       Up   0          0          0          0
                                             1       1000       5000        100
                                             2       2000          -        200
                                             3       3000          -        300
                                             4       4000          -        400
                                             5       5000          -        500
                                             6       6000          -        600
                                             7       7000          -        700
                                             8       8000          -        800
                                             9      10000          -       1000
-------------------------------------------------------------------------------
3                                     Down   0          0          0          0
                                             1       6000       5000       8000
                                             2      10000      10000      10000
                                             3      15000      15000          -
                                             4      22000          -          -
-------------------------------------------------------------------------------
10    base                              Up   0          0          0          0
                                             1       5000       5000       5000
                                             2      10000      10000      10000
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
* indicates that the corresponding row element may have been truncated.


show oam-pm bin-group 2 
-------------------------------------------------------------------------------
Configured Lower Bounds for Delay Measurement (DMM) Tests, in microseconds
-------------------------------------------------------------------------------
Group Description                    Admin Bin     FD(us)    FDR(us)   IFDV(us)
-------------------------------------------------------------------------------
2                                       Up   0          0          0          0
                                             1       1000       5000        100
                                             2       2000          -        200
                                             3       3000          -        300
                                             4       4000          -        400
                                             5       5000          -        500
                                             6       6000          -        600
                                             7       7000          -        700
                                             8       8000          -        800
                                             9      10000          -       1000
-------------------------------------------------------------------------------

bin-group-using

Syntax

bin-group-using [bin-group bin-group-number]

Context

show>oam-pm

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

This command displays the list of sessions configured against one or all OAM-PM bin groups.

Parameters

bin-group-number

Specifies an OAM-PM bin group.

Values: 1 to 255

Output

The following output is an example of OAM-PM bin group sessions information.

Sample output

show oam-pm bin-group-using 
=========================================================================
OAM Performance Monitoring Bin Group Configuration for Sessions
=========================================================================
Bin Group       Admin   Session                            Session State
-------------------------------------------------------------------------
2               Up      eth-vpls-00005                             Inact
                        eth-pm-service-4                             Act
-------------------------------------------------------------------------
3               Down    eth-epipe-000001                           Inact
-------------------------------------------------------------------------
10              Up      eth-epipe-00002                            Inact
-------------------------------------------------------------------------
========================================================================= 
Admin: State of the bin group
Session State: The state of session referencing the bin-group


show oam-pm bin-group-using bin-group 2
=========================================================================
OAM Performance Monitoring Bin Group Configuration for Sessions
=========================================================================
Bin Group       Admin   Session                            Session State
-------------------------------------------------------------------------
2               Up      eth-vpls-00005                             Inact
                        eth-pm-service-4                             Act
-------------------------------------------------------------------------
=========================================================================
Admin: State of the bin group
Session State: The state of session referencing the bin-group

session

Syntax

session session-name [{all | base | bin-group | event-mon | meas-interval}]

Context

show>oam-pm

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

This command displays the configuration and status information for an OAM-PM session.

Parameters

session-name: Specifies the name of the session. 32 characters maximum.

all: Specifies all attributes.

base: Specifies the base configuration option for the session.

bin-group: Specifies the associated bin group and its attributes.

event-mon: Specifies configured event monitoring and last TCA information.

meas-interval: Specifies the associated measured interval and its attributes.

Output

The following output is an example of OAM-PM session information.

Sample output

show oam-pm session "eth-pm-service-4" all 
-------------------------------------------------------------------------------
Basic Session Configuration
-------------------------------------------------------------------------------
Session Name      : eth-pm-service-4
Description       : (Not Specified)
Test Family       : ethernet            Session Type       : proactive
Bin Group         : 2
-------------------------------------------------------------------------------

-------------------------------------------------------------------------------
Ethernet Configuration
-------------------------------------------------------------------------------
Source MEP        : 28                  Priority           : 0
Source Domain     : 12                  Dest MAC Address   : 00:00:00:00:00:30
Source Assoc'n    : 4
-------------------------------------------------------------------------------

-------------------------------------------------------------------------------
DMM Test Configuration and Status
-------------------------------------------------------------------------------
Test ID           : 10004               Admin State        : Up
Oper State        : Up                  Data TLV Size      : 1000 octets
On-Demand Duration: Not Applicable      On-Demand Remaining: Not Applicable
Interval          : 1000 ms
-------------------------------------------------------------------------------

-------------------------------------------------------------------------------
SLM Test Configuration and Status
-------------------------------------------------------------------------------
Test ID           : 10004               Admin State        : Up
Oper State        : Up                  Data TLV Size      : 1000 octets
On-Demand Duration: Not Applicable      On-Demand Remaining: Not Applicable
Interval          : 100 ms
CHLI Threshold    : 4 HLIs              Frames Per Delta-T : 10 SLM frames
Consec Delta-Ts   : 10                  FLR Threshold      : 50%
-------------------------------------------------------------------------------

-------------------------------------------------------------------------------
15-mins Measurement Interval Configuration
-------------------------------------------------------------------------------
Duration          : 15-mins             Intervals Stored   : 32
Boundary Type     : clock-aligned       Clock Offset       : 0 seconds
Accounting Policy : none
-------------------------------------------------------------------------------

-------------------------------------------------------------------------------
Configured Lower Bounds for Delay Measurement (DMM) Tests, in microseconds
-------------------------------------------------------------------------------
Group Description                    Admin Bin     FD(us)    FDR(us)   IFDV(us)
-------------------------------------------------------------------------------
2                                       Up   0          0          0          0
                                             1       1000       5000        100
                                             2       2000          -        200
                                             3       3000          -        300
                                             4       4000          -        400
                                             5       5000          -        500
                                             6       6000          -        600
                                             7       7000          -        700
                                             8       8000          -        800
                                             9      10000          -       1000
------------------------------------------------------------------------------- 

show oam-pm session "eth-pm-service-4" base  
-------------------------------------------------------------------------------
Basic Session Configuration
-------------------------------------------------------------------------------
Session Name      : eth-pm-service-4
Description       : (Not Specified)
Test Family       : ethernet            Session Type       : proactive
Bin Group         : 2
-------------------------------------------------------------------------------

-------------------------------------------------------------------------------
Ethernet Configuration
-------------------------------------------------------------------------------
Source MEP        : 28                  Priority           : 0
Source Domain     : 12                  Dest MAC Address   : 00:00:00:00:00:30
Source Assoc'n    : 4
-------------------------------------------------------------------------------

-------------------------------------------------------------------------------
DMM Test Configuration and Status
-------------------------------------------------------------------------------
Test ID           : 10004               Admin State        : Up
Oper State        : Up                  Data TLV Size      : 1000 octets
On-Demand Duration: Not Applicable      On-Demand Remaining: Not Applicable
Interval          : 1000 ms
-------------------------------------------------------------------------------

-------------------------------------------------------------------------------
SLM Test Configuration and Status
-------------------------------------------------------------------------------
Test ID           : 10004               Admin State        : Up
Oper State        : Up                  Data TLV Size      : 1000 octets
On-Demand Duration: Not Applicable      On-Demand Remaining: Not Applicable
Interval          : 100 ms
CHLI Threshold    : 4 HLIs              Frames Per Delta-T : 10 SLM frames
Consec Delta-Ts   : 10                  FLR Threshold      : 50%
------------------------------------------------------------------------------- 

show oam-pm session "eth-pm-service-4" bin-group
-------------------------------------------------------------------------------
Configured Lower Bounds for Delay Measurement (DMM) Tests, in microseconds
-------------------------------------------------------------------------------
Group Description                    Admin Bin     FD(us)    FDR(us)   IFDV(us)
-------------------------------------------------------------------------------
2                                       Up   0          0          0          0
                                             1       1000       5000        100
                                             2       2000          -        200
                                             3       3000          -        300
                                             4       4000          -        400
                                             5       5000          -        500
                                             6       6000          -        600
                                             7       7000          -        700
                                             8       8000          -        800
                                             9      10000          -       1000
------------------------------------------------------------------------------- 


show oam-pm session "eth-pm-service-4" meas-interval
-------------------------------------------------------------------------------
15-mins Measurement Interval Configuration
-------------------------------------------------------------------------------
Duration          : 15-mins             Intervals Stored   : 32
Boundary Type     : clock-aligned       Clock Offset       : 0 seconds
Accounting Policy : none
-------------------------------------------------------------------------------

sessions

Syntax

sessions [test-family {ethernet | ip}] [event-mon]

Context

show>oam-pm

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

This command displays a summary of the OAM-PM sessions.

Parameters

ethernet: Specifies Ethernet sessions only.

ip: Specifies IP sessions only.

event-mon: Specifies a summary of all event monitoring information, and the current state for each session.

Output

The following output is an example of summary OAM-PM session information.

Sample output

show oam-pm sessions 
============================================================================
OAM Performance Monitoring Session Summary for the Ethernet Test Family
============================================================================
Session                          State   Bin Group   Sess Type   Test Types
----------------------------------------------------------------------------
eth-vpls-00005                   Inact           2   proactive      DMM SLM
eth-epipe-00002                  Inact          10   proactive      DMM SLM
eth-epipe-000001                 Inact           3   proactive      DMM  
eth-pm-service-4                   Act           2   proactive      DMM SLM
============================================================================ 


show oam-pm sessions test-family ethernet
============================================================================
OAM Performance Monitoring Session Summary for the Ethernet Test Family
============================================================================
Session                          State   Bin Group   Sess Type   Test Types
----------------------------------------------------------------------------
eth-vpls-00005                   Inact           2   proactive      DMM SLM
eth-epipe-00002                  Inact          10   proactive      DMM SLM
eth-epipe-000001                 Inact           3   proactive      DMM   
eth-pm-service-4                   Act           2   proactive      DMM SLM
============================================================================

statistics

Syntax

statistics

Context

show>oam-pm

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

Commands in this context display OAM-PM delay or synthetic loss statistics.

session

Syntax

session session-name

Context

show>oam-pm>statistics

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

This command displays OAM-PM session statistics.

Parameters

session-name: Specifies the session name. 32 characters maximum.

dmm

Syntax

dmm

Context

show>oam-pm>statistics>session

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

Commands in this context display DMM test statistics.

meas-interval

Syntax

meas-interval raw [{all | bins | summary}]

meas-interval {5-mins | 15-mins | 1-hour | 1-day} interval-number interval-number [{all | bins | summary}]

Context

show>oam-pm>statistics>session>dmm

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

This command displays measured interval statistics for DMM tests in the specified session.

Parameters

raw: Specifies raw information.

5-mins: Specifies information for 5-min intervals.

15-mins: Specifies information for 15-min intervals.

1-hour: Specifies information for 1-hour intervals.

1-day: Specifies information for 1-day intervals.

interval-number

Specifies the interval number.

Values: 1 to 97

all: Specifies all information for the interval.

bins: Specifies bin information for the interval.

summary: Specifies summarized information for the interval.

Output

The following output is an example of DMM measured interval statistics information.

Sample output

show oam-pm statistics session "eth-pm-service-4" dmm meas-interval 15-
mins all interval-number 2
------------------------------------------------------------------------------
Start (UTC)       : 2014/02/01 10:15:00          Status          : completed
Elapsed (seconds) : 900                          Suspect         : no
Frames Sent       : 900                          Frames Received : 900
------------------------------------------------------------------------------

----------------------------------------------------------------------
Bin Type     Direction     Minimum (us)   Maximum (us)   Average (us)
----------------------------------------------------------------------
FD           Forward                  0          11670            779
FD           Backward                 0           7076           1746
FD           Round Trip            1109          13222           2293
FDR          Forward                  0          11670            779
FDR          Backward                 0           7076           1738
FDR          Round Trip               0          12104           1178
IFDV         Forward                  0          10027            489
IFDV         Backward                 0           5444            742
IFDV         Round Trip               0          11853           1088
----------------------------------------------------------------------

---------------------------------------------------------------
Frame Delay (FD) Bin Counts
---------------------------------------------------------------
Bin      Lower Bound       Forward      Backward    Round Trip
---------------------------------------------------------------
0               0 us           625           244             0
1            1000 us           194           356           465
2            2000 us            50           153           244
3            3000 us            11           121           119
4            4000 us            10            17            40
5            5000 us             5             6            20
6            6000 us             4             2             5
7            7000 us             0             1             3
8            8000 us             0             0             3
9           10000 us             1             0             1
---------------------------------------------------------------

---------------------------------------------------------------
Frame Delay Range (FDR) Bin Counts
---------------------------------------------------------------
Bin      Lower Bound       Forward      Backward    Round Trip
---------------------------------------------------------------
0               0 us           890           891           889
1            5000 us            10             9            11
---------------------------------------------------------------

---------------------------------------------------------------
Inter-Frame Delay Variation (IFDV) Bin Counts
---------------------------------------------------------------
Bin      Lower Bound       Forward      Backward    Round Trip
---------------------------------------------------------------
0               0 us           398           255           102
1             100 us            82            88            89
2             200 us            79            57            59
3             300 us            60            63            61
4             400 us            39            37            54
5             500 us            31            24            42
6             600 us            26            30            43
7             700 us            29            20            34
8             800 us            54            47            67
9            1000 us           102           279           349
---------------------------------------------------------------

show oam-pm statistics session "eth-pm-service-4" dmm meas-interval 15-
mins bins interval-number 2
------------------------------------------------------------------------------
Start (UTC)       : 2014/02/01 10:30:00          Status          : completed
Elapsed (seconds) : 900                          Suspect         : no
Frames Sent       : 900                          Frames Received : 900
------------------------------------------------------------------------------

---------------------------------------------------------------
Frame Delay (FD) Bin Counts
---------------------------------------------------------------
Bin      Lower Bound       Forward      Backward    Round Trip
---------------------------------------------------------------
0               0 us           699           167             0
1            1000 us           169           312           456
2            2000 us            24           228           274
3            3000 us             3           136           111
4            4000 us             3            48            41
5            5000 us             1             7            10
6            6000 us             1             1             3
7            7000 us             0             1             2
8            8000 us             0             0             3
9           10000 us             0             0             0
---------------------------------------------------------------

---------------------------------------------------------------
Frame Delay Range (FDR) Bin Counts
---------------------------------------------------------------
Bin      Lower Bound       Forward      Backward    Round Trip
---------------------------------------------------------------
0               0 us           898           891           892
1            5000 us             2             9             8
---------------------------------------------------------------

---------------------------------------------------------------
Inter-Frame Delay Variation (IFDV) Bin Counts
---------------------------------------------------------------
Bin      Lower Bound       Forward      Backward    Round Trip
---------------------------------------------------------------
0               0 us           462           217           107
1             100 us            63            99            80
2             200 us            64            85            71
3             300 us            63            74            53
4             400 us            34            53            45
5             500 us            37            24            50
6             600 us            34            17            41
7             700 us            35            23            57
8             800 us            46            32            60
9            1000 us            62           276           336
--------------------------------------------------------------- 

show oam-pm statistics session "eth-pm-service-4" dmm meas-interval 15-
mins summary interval-number 2
------------------------------------------------------------------------------
Start (UTC)       : 2014/02/01 10:30:00          Status          : completed
Elapsed (seconds) : 900                          Suspect         : no
Frames Sent       : 900                          Frames Received : 900
------------------------------------------------------------------------------

----------------------------------------------------------------------
Bin Type     Direction     Minimum (us)   Maximum (us)   Average (us)
----------------------------------------------------------------------
FD           Forward                  0           6379            518
FD           Backward                 0           7856           2049
FD           Round Trip            1118           9879           2241
FDR          Forward                  0           6379            518
FDR          Backward                 0           7856           2049
FDR          Round Trip               9           8770           1132
IFDV         Forward                  0           6021            328
IFDV         Backward                 0           5800            732
IFDV         Round Trip               2           7758            984
----------------------------------------------------------------------

show oam-pm statistics session "eth-pm-service-4" dmm meas-interval raw
------------------------------------------------------------------------------
Start (UTC)       : 2014/02/01 09:43:58          Status          : in-progress
Elapsed (seconds) : 3812                         Suspect         : yes
Frames Sent       : 3812                         Frames Received : 3812
------------------------------------------------------------------------------

----------------------------------------------------------------------
Bin Type     Direction     Minimum (us)   Maximum (us)   Average (us)
----------------------------------------------------------------------
FD           Forward                  0          11670            629
FD           Backward                 0          11710           2156
FD           Round Trip            1109          14902           2497
FDR          Forward                  0          11670            617
FDR          Backward                 0          11710           2156
FDR          Round Trip               0          13784           1360
IFDV         Forward                  0          10027            404
IFDV         Backward                 0          10436            768
IFDV         Round Trip               0          13542           1056
----------------------------------------------------------------------

---------------------------------------------------------------
Frame Delay (FD) Bin Counts
---------------------------------------------------------------
Bin      Lower Bound       Forward      Backward    Round Trip
---------------------------------------------------------------
0               0 us          2815           661             0
1            1000 us           803          1287          1591
2            2000 us           127           971          1227
3            3000 us            21           639           623
4            4000 us            25           181           232
5            5000 us            12            42            72
6            6000 us             7            14            28
7            7000 us             0             4            13
8            8000 us             1            12            19
9           10000 us             1             1             7
---------------------------------------------------------------

---------------------------------------------------------------
Frame Delay Range (FDR) Bin Counts
---------------------------------------------------------------
Bin      Lower Bound       Forward      Backward    Round Trip
---------------------------------------------------------------
0               0 us          3792          3740          3751
1            5000 us            21            73            62
---------------------------------------------------------------

---------------------------------------------------------------
Inter-Frame Delay Variation (IFDV) Bin Counts
---------------------------------------------------------------
Bin      Lower Bound       Forward      Backward    Round Trip
---------------------------------------------------------------
0               0 us          1815           884           410
1             100 us           338           439           354
2             200 us           280           313           282
3             300 us           241           313           268
4             400 us           162           193           231
5             500 us           134           141           202
6             600 us           126           102           178
7             700 us           127            97           153
8             800 us           208           165           276
9            1000 us           381          1165          1458
---------------------------------------------------------------

slm

Syntax

slm

Context

show>oam-pm>statistics>session

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

Commands in this context display SLM test statistics.

meas-interval

Syntax

meas-interval raw

meas-interval {5-mins | 15-mins | 1-hour | 1-day} interval-number interval-number

Context

show>oam-pm>statistics>session>slm

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

This command displays measured interval statistics for SLM tests in the specified session

Parameters

raw: Specifies raw information.

5-mins: Specifies information for 5-min intervals.

15-mins: Specifies information for 15-min intervals.

1-hour: Specifies information for 1-hour intervals.

1-day: Specifies information for 1-day intervals.

interval-number

Specifies the interval number.

Values: 1 to 97

Output

The following output is an example of SLM measured interval statistics information.

Sample output

show oam-pm statistics session "eth-pm-service-4" slm meas-interval 15-
mins interval-number 2
------------------------------------------------------------------------------
Start (UTC)       : 2014/02/01 10:30:00          Status          : completed
Elapsed (seconds) : 900                          Suspect         : no
Frames Sent       : 9000                         Frames Received : 9000
------------------------------------------------------------------------------

------------------------------------------------------
                    Frames Sent       Frames Received
------------------------------------------------------
Forward                    9000                  9000
Backward                   9000                  9000
------------------------------------------------------

-------------------------------------------
Frame Loss Ratios
-------------------------------------------
             Minimum    Maximum    Average
-------------------------------------------
Forward       0.000%     0.000%     0.000%
Backward      0.000%     0.000%     0.000%
-------------------------------------------

-------------------------------------------------------------------------------
Availability Counters (Und = Undetermined)
-------------------------------------------------------------------------------
           Available   Und-Avail Unavailable Und-Unavail        HLI       CHLI
-------------------------------------------------------------------------------
Forward          900           0           0           0          0          0
Backward         900           0           0           0          0          0
------------------------------------------------------------------------------- 

show oam-pm statistics session "eth-pm-service-4" slm meas-interval raw     
------------------------------------------------------------------------------
Start (UTC)       : 2014/02/01 09:44:03          Status          : in-progress
Elapsed (seconds) : 4152                         Suspect         : yes
Frames Sent       : 41523                        Frames Received : 41523
------------------------------------------------------------------------------

------------------------------------------------------
                    Frames Sent       Frames Received
------------------------------------------------------
Forward                   41369                 41369
Backward                  41369                 41369
------------------------------------------------------

-------------------------------------------
Frame Loss Ratios
-------------------------------------------
             Minimum    Maximum    Average
-------------------------------------------
Forward       0.000%     0.000%     0.000%
Backward      0.000%     0.000%     0.000%
-------------------------------------------

-------------------------------------------------------------------------------
Availability Counters (Und = Undetermined)
-------------------------------------------------------------------------------
           Available   Und-Avail Unavailable Und-Unavail        HLI       CHLI
-------------------------------------------------------------------------------
Forward         4137           0           0           0          0          0
Backward        4137           0           0           0          0          0
------------------------------------------------------------------------------- 
Ib

twamp-light

Syntax

twamp-light

Context

show>oam-pm>statistics>session

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

Commands in this context display TWAMP Light test statistics.

meas-interval

Syntax

meas-interval raw delay [{all | bins | summary}]

meas-interval raw [loss]

meas-interval {5-mins | 15-mins | 1-hour | 1-day} interval-number interval-number delay [{all | bins | summary}]

meas-interval {5-mins | 15-mins | 1-hour | 1-day} interval-number interval-number [loss]

Context

show>oam-pm>statistics>session>twamp-light

Platforms

Supported on all 7210 SAS platforms as described in this document, including platforms configured in the access-uplink operating mode

Description

This command displays measured interval statistics for TWAMP-Light tests in the specified session.

Parameters

raw: Specifies raw information.

5-mins: Specifies information for 5-min intervals.

15-mins: Specifies information for 15-min intervals.

1-hour: Specifies information for 1-hour intervals.

1-day: Specifies information for 1-day intervals.

interval-number

Specifies the interval number.

Values: 1 to 97

delay: Specifies TWAMP Light delay statistics only.

loss: Specifies TWAMP Light loss statistics only.

all: Specifies all information for the interval.

bins: Specifies bin information for the interval.

summary: Specifies summarized information for the interval.