egress-label start-label [end-label]
show>service
Supported on all 7210 SAS platforms as described in this document
This command displays service information using the range of egress labels.
If only the mandatory start-label parameter is specified, only services using the specified label are displayed.
If both start-label and end-label parameters are specified, the services using the labels in the specified range are displayed.
Use the show router ldp bindings command to display dynamic labels.
Specifies the starting egress label value for which to display services using the label range. If only egress-label1 is specified, services only using egress-label1 are displayed.
Specifies the ending egress label value for which to display services using the label range.
The following output is an example of egress label information, and Table: Output fields: egress label describes the output fields.
Sample output*A:ALA-12# show service egress-label 0 10000
==============================================================================
Martini Service Labels
==============================================================================
Svc Id Sdp Id Type I.Lbl E.Lbl
------------------------------------------------------------------------------
1 10:1 Mesh 0 0
1 20:1 Mesh 0 0
1 30:1 Mesh 0 0
1 100:1 Mesh 0 0
...
1 107:1 Mesh 0 0
1 108:1 Mesh 0 0
1 300:1 Mesh 0 0
1 301:1 Mesh 0 0
1 302:1 Mesh 0 0
1 400:1 Mesh 0 0
1 500:2 Spok 131070 2001
1 501:1 Mesh 131069 2000
100 300:100 Spok 0 0
200 301:200 Spok 0 0
300 302:300 Spok 0 0
400 400:400 Spok 0 0
------------------------------------------------------------------------------
Number of Bindings Found : 23
==============================================================================
*A:ALA-12#| Label | Description |
|---|---|
|
Svc Id |
The ID that identifies a service. |
|
Sdp Id |
The ID that identifies an SDP. |
|
Type |
Indicates whether the SDP binding is a spoke or a mesh. |
|
I. Lbl |
The VC label used by the far-end device to send packets to this device in this service by the SDP. |
|
E. Lbl |
The VC label used by this device to send packets to the far-end device in this service by the SDP. |
|
Number of bindings found |
The total number of SDP bindings that exist within the specified egress label range. |
ingress-label start-label [end-label]
show>service
Supported on all 7210 SAS platforms as described in this document
This command displays services using the range of ingress labels.
If only the mandatory start-label parameter is specified, only services using the specified label are displayed.
If both start-label and end-label parameters are specified, the services using the labels in the specified range are displayed.
Use the show router vprn-service-id ldp bindings command to display dynamic labels.
Specifies the starting ingress label value for which to display services using the label range. If only start-label is specified, services only using start-label are displayed.
Specifies the ending ingress label value for which to display services using the label range.
The following output is an example of ingress label information, and Table: Output fields: ingress label describes the output fields.
Sample output*A:ALA-12# show service ingress-label 0
==============================================================================
Martini Service Labels
==============================================================================
Svc Id Sdp Id Type I.Lbl E.Lbl
------------------------------------------------------------------------------
1 10:1 Mesh 0 0
1 20:1 Mesh 0 0
1 30:1 Mesh 0 0
1 50:1 Mesh 0 0
1 100:1 Mesh 0 0
1 101:1 Mesh 0 0
1 102:1 Mesh 0 0
1 103:1 Mesh 0 0
1 104:1 Mesh 0 0
1 105:1 Mesh 0 0
1 106:1 Mesh 0 0
1 107:1 Mesh 0 0
1 108:1 Mesh 0 0
1 300:1 Mesh 0 0
1 301:1 Mesh 0 0
1 302:1 Mesh 0 0
1 400:1 Mesh 0 0
100 300:100 Spok 0 0
200 301:200 Spok 0 0
300 302:300 Spok 0 0
400 400:400 Spok 0 0
------------------------------------------------------------------------------
Number of Bindings Found : 21
------------------------------------------------------------------------------
*A:ALA-12# | Label | Description |
|---|---|
|
Svc ID |
The service identifier. |
|
SDP Id |
The SDP identifier. |
|
Type |
Indicates whether the SDP is a spoke or a mesh. |
|
I.Lbl |
The ingress label used by the far-end device to send packets to this device in this service by the SDP. |
|
E.Lbl |
The egress label used by this device to send packets to the far-end device in this service by the SDP. |
|
Number of Bindings Found |
The number of SDP bindings within the label range specified. |
sap-using [sap sap-id]
sap-using interface [ip-address | ip-int-name]
sap-using [ingress | egress] filter filter-id
sap-using [ingress | egress] qos-policy qos-policy-id
show>service
Supported on all 7210 SAS platforms as described in this document
This command displays SAP information.
If no optional parameters are specified, the command displays a summary of all defined SAPs.
The optional parameters restrict output to only SAPs matching the specified properties.
Specifies the physical port identifier portion of the SAP definition. See Common CLI command descriptions for command syntax.
Keyword to specify matching SAPs with the specified IP interface.
Specifies the IP address of the interface for which to display matching SAPs.
Specifies the IP interface name for which to display matching SAPs.
Keyword to specify matching an ingress policy.
Keyword to specify matching an egress policy.
Specifies the ingress or egress QoS policy ID for which to display matching SAPs.
Specifies the ingress or egress filter policy ID for which to display matching SAPs.
The following output is an example of SAP service using information, and Table: Output fields: service SAP using describes the output fields.
Sample output*A:ALA-12# show service sap-using sap 1/1
==============================================================================
Service Access Points
==============================================================================
PortId SvcId SapMTU I.QoS I.Mac/IP E.QoS E.Mac/IP A.Pol Adm Opr
------------------------------------------------------------------------------
1/1/7:0 1 1518 10 8 10 none none Up Up
1/1/11:0 100 1514 1 none 1 none none Down Down
1/1/7:300 300 1518 10 none 10 none 1000 Up Up
------------------------------------------------------------------------------
Number of SAPs : 3
------------------------------------------------------------------------------
*A:ALA-12# | Label | Description |
|---|---|
|
Port ID |
The ID of the access port where the SAP is defined. |
|
Svc ID |
The service identifier. |
|
SapMTU |
The SAP MTU value. |
|
I.QoS |
The SAP ingress QoS policy number specified on the ingress SAP. |
|
I.MAC/IP |
The MAC or IP filter policy ID applied to the ingress SAP. |
|
E.QoS |
The SAP egress QoS policy number specified on the egress SAP. |
|
E.Mac/IP |
The MAC or IP filter policy ID applied to the egress SAP |
|
A.Pol |
The accounting policy ID assigned to the SAP. |
|
Adm |
The configured state of the SAP. |
|
Opr |
The actual state of the SAP. |
sdp [sdp-id | far-end ip-address] [detail | keep-alive-history]
show>service
Supported on all 7210 SAS platforms as described in this document
This command displays SDP information.
If no optional parameters are specified, a summary SDP output for all SDPs is displayed.
Specifies the SDP ID for which to display information.
Displays only SDPs matching with the specified far-end IP address.
Displays detailed SDP information.
Displays the last fifty SDP keepalive events for the SDP.
The following output is an example of SDP information, and Table: Output fields: service SDP describes the output fields.
Sample output*A:ALA-12# show service sdp
==============================================================================
Services: Service Destination Points
==============================================================================
SdpId Adm MTU Opr MTU IP address Adm Opr Deliver Signal
------------------------------------------------------------------------------
10 4462 4462 10.20.1.3 Up Dn NotReady MPLS TLDP
40 4462 1534 10.20.1.20 Up Up MPLS TLDP
------------------------------------------------------------------------------
Number of SDPs : 5
==============================================================================
*A:ALA-12#
*A:ALA-12# show service sdp 8
==============================================================================
Service Destination Point (Sdp Id : 8)
==============================================================================
SdpId Adm MTU Opr MTU IP address Adm Opr Deliver Signal
------------------------------------------------------------------------------
8 4462 4462 10.10.10.104 Up Dn NotReady MPLS TLDP
==============================================================================
Service Destination Point (Sdp Id : 8) Details
-------------------------------------------------------------------------------
Sdp Id 8 -(10.10.10.104)
-------------------------------------------------------------------------------
Description : MPLS-10.10.10.104
SDP Id : 8
Admin Path MTU : 0 Oper Path MTU : 0
Far End : 10.10.10.104 Delivery : MPLS
Admin State : Up Oper State : Down
Flags : SignalingSessDown TransportTunnDown
Signaling : TLDP VLAN VC Etype : 0x8100
Last Status Change : 02/01/2007 09:11:39 Adv. MTU Over. : No
Last Mgmt Change : 02/01/2007 09:11:46
KeepAlive Information :
Admin State : Disabled Oper State : Disabled
Hello Time : 10 Hello Msg Len : 0
Hello Timeout : 5 Unmatched Replies : 0
Max Drop Count : 3 Hold Down Time : 10
Tx Hello Msgs : 0 Rx Hello Msgs : 0
Associated LSP LIST :
Lsp Name : to-104
Admin State : Up Oper State : Down
Time Since Last Tran*: 01d07h36m
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:ALA-12#| Label | Description |
|---|---|
|
SDP Id |
The SDP identifier. |
|
Adm MTU |
Specifies the largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented. |
|
Opr MTU |
Specifies the actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented. |
|
IP address |
Specifies the IP address of the remote end of the MPLS tunnel defined by this SDP. |
|
Adm Admin State |
Specifies the state of the SDP. |
|
Opr Oper State |
Specifies the operating state of the SDP. |
|
Flags |
Specifies all the conditions that affect the operating status of this SDP. |
|
Signal Signaling |
Specifies the signaling protocol used to obtain the ingress and egress labels used in frames transmitted and received on the SDP. |
|
Last Status Change |
Specifies the time of the most recent operating status change to this SDP. |
|
Last Mgmt Change |
Specifies the time of the most recent management-initiated change to this SDP. |
|
Number of SDPs |
Specifies the total number of SDPs displayed according to the criteria specified. |
|
Hello Time |
Specifies how often the SDP echo request messages are transmitted on this SDP. |
|
Deliver Delivered |
Specifies the type of delivery used by the SDP: MPLS. |
|
Number of SDPs |
Specifies the total number of SDPs displayed according to the criteria specified. |
|
Hello Time |
Specifies how often the SDP echo request messages are transmitted on this SDP. |
|
Hello Msg Len |
Specifies the length of the SDP echo request messages transmitted on this SDP. |
|
Hello Timeout |
Specifies the number of seconds to wait for an SDP echo response message before declaring a timeout. |
|
Unmatched Replies |
Specifies the number of SDP unmatched message replies. |
|
Max Drop Count |
Specifies the maximum number of consecutive SDP echo request messages that can be unacknowledged before the keepalive protocol reports a fault. |
|
Hold Down Time |
Specifies the maximum number of consecutive SDP echo request messages that can be unacknowledged before the keepalive protocol reports a fault. |
|
TX Hello Msgs |
Specifies the number of SDP echo request messages transmitted after the keepalive was administratively enabled or the counter was cleared. |
|
Rx Hello Msgs |
Specifies the number of SDP echo request messages received after the keepalive was administratively enabled or the counter was cleared. |
|
Associated LSP List |
When the SDP type is MPLS, a list of LSPs used to reach the far-end router displays. All the LSPs in the list must terminate at the IP address specified in the far end field. |
sdp-using [sdp-id[:vc-id] | far-end ip-address]
show>service
Supported on all 7210 SAS platforms as described in this document
This command displays services using SDP or far-end address options.
Displays only services bound to the specified SDP ID.
Specifies the virtual circuit identifier.
Displays only services matching with the specified far-end IP address.
The following output is an example of SDP service information, and Table: Output fields: service SDP using describes the output fields.
Sample output*A:ALA-1# show service sdp-using 300
===============================================================================
Service Destination Point (Sdp Id : 300)
===============================================================================
SvcId SdpId Type Far End Opr State I.Label E.Label
-------------------------------------------------------------------------------
1 300:1 Mesh 10.0.0.13 Up 131071 131071
2 300:2 Spok 10.0.0.13 Up 131070 131070
100 300:100 Mesh 10.0.0.13 Up 131069 131069
101 300:101 Mesh 10.0.0.13 Up 131068 131068
102 300:102 Mesh 10.0.0.13 Up 131067 131067
-------------------------------------------------------------------------------
Number of SDPs : 5
-------------------------------------------------------------------------------
*A:ALA-1#
A:ALA-48# show service sdp-using
===============================================================================
SDP Using
===============================================================================
SvcId SdpId Type Far End Opr State I.Label E.Label
-------------------------------------------------------------------------------
3 2:3 Spok 10.20.1.2 Up n/a n/a
103 3:103 Spok 10.20.1.3 Up 131067 131068
103 4:103 Spok 10.20.1.2 Up 131065 131069
105 3:105 Spok 10.20.1.3 Up 131066 131067
-------------------------------------------------------------------------------
Number of SDPs : 4
-------------------------------------------------------------------------------
A:ALA-48| Label | Description |
|---|---|
|
Svc ID |
The service identifier. |
|
Sdp ID |
The SDP identifier. |
|
Type |
Type of SDP: spoke or mesh. |
|
Far End |
The far end address of the SDP. |
|
Oper State |
The operational state of the service. |
|
Ingress Label |
The label used by the far-end device to send packets to this device in this service by this SDP. |
|
Egress Label |
The label used by this device to send packets to the far-end device in this service by this SDP. |
service-using [epipe] [ies] [vpls] [vprn][sdp sdp-id] [customer customer-id]
show>service
Supported on all 7210 SAS platforms as described in this document
This command displays the services matching specified usage properties.
If no optional parameters are specified, all services defined on the system are displayed.
Displays matching Epipe services.
Displays matching IES instances.
Displays matching VPLS instances.
Displays matching VPRN services.
Displays only services bound to the specified SDP ID.
Displays services only associated with the specified customer ID.
The following output is an example of service using information, and Table: Output fields: service using describes the output fields.
Sample output*A:ALA-12# show service service-using customer 10
==============================================================================
Services
==============================================================================
ServiceId Type Adm Opr CustomerId Last Mgmt Change
------------------------------------------------------------------------------
1 VPLS Up Up 10 09/05/2006 13:24:15
100 IES Up Up 10 09/05/2006 13:24:15
300 Epipe Up Up 10 09/05/2006 13:24:15
900 VPRN Up Up 2 11/04/2006 04:55:12
------------------------------------------------------------------------------
Matching Services : 4
==============================================================================
*A:ALA-12#
*A:ALA-12# show service service-using epipe
===============================================================================
Services [epipe]
===============================================================================
ServiceId Type Adm Opr CustomerId Last Mgmt Change
-------------------------------------------------------------------------------
6 Epipe Up Up 6 06/22/2006 23:05:58
7 Epipe Up Up 6 06/22/2006 23:05:58
8 Epipe Up Up 3 06/22/2006 23:05:58
103 Epipe Up Up 6 06/22/2006 23:05:58
-------------------------------------------------------------------------------
Matching Services : 4
===============================================================================
*A:ALA-12#
A:de14# show service service-using
===============================================================================
Services
===============================================================================
ServiceId Type Adm Opr CustomerId Last Mgmt Change
-------------------------------------------------------------------------------
1 uVPLS Up Up 1 10/26/2006 15:44:57
2 Epipe Up Down 1 10/26/2006 15:44:57
10 mVPLS Down Down 1 10/26/2006 15:44:57
11 mVPLS Down Down 1 10/26/2006 15:44:57
100 mVPLS Up Up 1 10/26/2006 15:44:57
101 mVPLS Up Up 1 10/26/2006 15:44:57
102 mVPLS Up Up 1 10/26/2006 15:44:57
999 uVPLS Down Down 1 10/26/2006 16:14:33
-------------------------------------------------------------------------------
Matching Services : 8
-------------------------------------------------------------------------------
A:de14#| Label | Description |
|---|---|
|
Service Id |
The service identifier. |
|
Type |
Specifies the service type configured for the service ID. |
|
Adm |
The configured state of the service. |
|
Opr |
The operating state of the service. |
|
CustomerID |
The ID of the customer who owns this service. |
|
Last Mgmt Change |
The date and time of the most recent management-initiated change to this service. |
id service-id {all | arp | base | fdb | labels | mfib | sap | sdp | split-horizon-group | stp}
show>service
Supported on all 7210 SAS platforms as described in this document
This command displays information for a specified service ID.
Specifies the unique service identification number that identifies the service in the service domain.
Displays detailed information about the service.
Displays ARP entries for the service.
Displays basic service information.
Displays FDB entries.
Displays service interfaces.
Displays labels being used by this service.
Displays SAPs associated with the service.
Displays SDPs associated with the service.
Displays split horizon group information.
Displays STP information.
all
show>service>id
Supported on all 7210 SAS platforms as described in this document
This command displays detailed information for all aspects of the service.
The following output is an example of detailed service information, and Table: Output fields: service ID All describes the output fields.
Sample output*A:7210SAS>show>service>id# all
===============================================================================
Service Detailed Information
===============================================================================
Service Id : 1 Vpn Id : 0
Service Type : Epipe
Description : (Not Specified)
Customer Id : 1
Last Status Change: 02/12/2002 23:51:07
Last Mgmt Change : 02/12/2002 23:50:18
Admin State : Up Oper State : Up
SAP Count : 2
Uplink Type: : L2
SAP Type: : Any Customer vlan: : n/a
-------------------------------------------------------------------------------
Service Access Points
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
SAP 1/1/9:600.*
-------------------------------------------------------------------------------
Service Id : 1
SAP : 1/1/9:600.* Encap : qinq
QinQ Dot1p : Default
Description : (Not Specified)
Admin State : Up Oper State : Up
Flags : None
Last Status Change : 02/12/2002 23:51:06
Last Mgmt Change : 02/12/2002 23:50:18
Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100
Admin MTU : 9212 Oper MTU : 9212
Ingr IP Fltr-Id : n/a Egr IP Fltr-Id : n/a
Ingr Mac Fltr-Id : n/a Egr Mac Fltr-Id : n/a
Ingr IPv6 Fltr-Id : n/a Egr IPv6 Fltr-Id : n/a
tod-suite : None
Endpoint : N/A
Acct. Pol : None Collect Stats : Disabled
-------------------------------------------------------------------------------
QOS
-------------------------------------------------------------------------------
Ingress qos-policy : n/a
-------------------------------------------------------------------------------
Aggregate Policer
-------------------------------------------------------------------------------
rate : n/a burst : n/a
-------------------------------------------------------------------------------
Ingress QoS Classifier Usage
-------------------------------------------------------------------------------
Classifiers Allocated: 2 Meters Allocated : 1
Classifiers Used : 1 Meters Used : 1
-------------------------------------------------------------------------------
Sap Statistics
-------------------------------------------------------------------------------
Packets Octets
Ingress Stats: 0 0
Egress Stats: 26941105 18014193523
Extra-Tag Drop Stats: n/a n/a
-------------------------------------------------------------------------------
SAP 1/1/12:90
-------------------------------------------------------------------------------
Service Id : 1
SAP : 1/1/12:90 Encap : q-tag
Description : (Not Specified)
Admin State : Up Oper State : Up
Flags : None
Last Status Change : 02/12/2002 23:51:07
Last Mgmt Change : 02/13/2002 00:05:46
Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100
Loopback Mode : Internal No-svc-port used : 1/1/25
Loopback Src Addr : 00:00:01:00:02:00
Loopback Dst Addr : 00:00:01:00:03:00
Admin MTU : 1518 Oper MTU : 1518
Ingr IP Fltr-Id : n/a Egr IP Fltr-Id : n/a
Ingr Mac Fltr-Id : n/a Egr Mac Fltr-Id : n/a
Ingr IPv6 Fltr-Id : n/a Egr IPv6 Fltr-Id : n/a
tod-suite : None
Endpoint : N/A
Acct. Pol : None Collect Stats : Disabled
-------------------------------------------------------------------------------
QOS
-------------------------------------------------------------------------------
Ingress qos-policy : 1
-------------------------------------------------------------------------------
Aggregate Policer
-------------------------------------------------------------------------------
rate : n/a burst : n/a
-------------------------------------------------------------------------------
Ingress QoS Classifier Usage
-------------------------------------------------------------------------------
Classifiers Allocated: 2 Meters Allocated : 1
Classifiers Used : 1 Meters Used : 1
-------------------------------------------------------------------------------
Sap Statistics
-------------------------------------------------------------------------------
Packets Octets
Ingress Stats: 26940595 18013850572
Egress Stats: 0 0
Ingress Drop Stats: 0 0
Extra-Tag Drop Stats: n/a n/a
-------------------------------------------------------------------------------
Sap per Meter stats (in/out counter mode)
-------------------------------------------------------------------------------
Packets Octets
Ingress Meter 1
For. InProf : 8 4265
For. OutProf : 26941156 18014224039
-------------------------------------------------------------------------------
Service Endpoints
-------------------------------------------------------------------------------
No Endpoints found.
===============================================================================
*A:7210SAS>show>service>id#| Label | Description |
|---|---|
|
Service Detailed Information |
|
|
Service Id |
The service identifier. |
|
VPN Id |
The number that identifies the VPN. |
|
Customer Id |
The customer identifier. |
|
Last Status Change |
The date and time of the most recent change in the administrative or operating status of the service. |
|
Last Mgmt Change |
The date and time of the most recent management-initiated change to this customer. |
|
Admin State |
The current administrative state. |
|
Oper State |
The current operational state. |
|
Route Dist. |
Displays the route distribution number. |
|
AS Number |
Displays the autonomous system number. |
|
Router Id |
Displays the router ID for this service. |
|
Auto Bind |
Specifies the automatic binding type for the SDP assigned to this service. |
|
Vrf Target |
Specifies the VRF target applied to this service. |
|
Vrf Import |
Specifies the VRF import policy applied to this service. |
|
Vrf Export |
Specifies the VRF export policy applied to this service. |
|
Description |
Generic information about the service. |
|
SAP Count |
The number of SAPs specified for this service. |
|
SDP Bind Count |
The number of SDPs bound to this service. |
|
Split Horizon Group |
Name of the split horizon group for this service. |
|
Description |
Description of the split horizon group. |
|
Last Changed |
The date and time of the most recent management-initiated change to this split horizon group. |
|
Service Destination Points (SDPs) |
|
|
SDP Id |
The SDP identifier. |
|
Type |
Indicates whether this service SDP binding is a spoke or a mesh. |
|
Admin Path MTU |
The configured largest service frame size (in octets) that can be transmitted through this SDP to the far-end router without requiring the packet to be fragmented. |
|
Oper Path MTU |
The actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router without requiring the packet to be fragmented. |
|
Delivery |
Specifies the type of delivery used by the SDP: MPLS. |
|
Admin State |
The administrative state of this SDP. |
|
Oper State |
The operational state of this SDP. |
|
Ingress Label |
The label used by the far-end device to send packets to this device in this service by this SDP. |
|
Egress Label |
The label used by this device to send packets to the far-end device in this service by this SDP. |
|
Ingress Filter |
The ID of the ingress filter policy. |
|
Egress Filter |
The ID of the egress filter policy. |
|
Far End |
Specifies the IP address of the remote end of the MPLS tunnel defined by this SDP. |
|
Last Changed |
The date and time of the most recent change to this customer. |
|
Signaling |
Specifies the signaling protocol used to obtain the ingress and egress labels used in frames transmitted and received on this SDP. |
|
Admin State |
Specifies the operating status of the keepalive protocol. |
|
Oper State |
The current status of the keepalive protocol. |
|
Hello Time |
Specifies how often the SDP echo request messages are transmitted on this SDP. |
|
Hello Msg Len |
Specifies the length of the SDP echo request messages transmitted on this SDP. |
|
Max Drop Count |
Specifies the maximum number of consecutive SDP Echo Request messages that can be unacknowledged before the keepalive protocol reports a fault. |
|
Hold Down Time |
Specifies the amount of time to wait before the keepalive operating status is eligible to enter the alive state. |
|
SDP Delivery Mechanism |
When the SDP type is MPLS, a list of LSPs used to reach the far-end router displays. All the LSPs in the list must terminate at the IP address specified in the far end field. |
|
Max Drop Count |
Specifies the maximum number of consecutive SDP Echo Request messages that can be unacknowledged before the keepalive protocol reports a fault. |
|
Number of SDPs |
The total number SDPs applied to this service ID. |
|
Service Access Points |
|
|
Service Id |
The service identifier. |
|
Port Id |
The ID of the access port where this SAP is defined. |
|
Description |
Generic information about the SAP. |
|
Admin State |
The configured state of the SAP. |
|
Oper State |
The operating state of the SAP. |
|
Last Changed |
The date and time of the last change. |
|
Admin MTU |
The configured largest service frame size (in octets) that can be transmitted through this SDP to the far-end router without requiring the packet to be fragmented. |
|
Oper MTU |
The actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router without requiring the packet to be fragmented. |
|
Ingress qos-policy |
The SAP ingress QoS policy ID. |
|
Acct. Pol |
Indicates the accounting policy applied to the SAP. |
|
Collect Stats |
Specifies whether accounting statistics are collected on the SAP. |
|
Spoke SDPs |
|
|
Managed by Service |
Specifies the service ID of the management VPLS managing this spoke-SDP. |
|
Managed by Spoke |
Specifies the SAP ID inside the management VPLS managing this spoke-SDP. |
|
Prune state |
Specifies the STP state inherited from the management VPLS. |
|
Peer Pw Bits |
Indicates the bits set by the LDP peer when there is a fault on its side of the pseudowire. LAC failures occur on the SAP that has been configured on the pipe service. PSN bits are set by SDP-binding failures on the pipe service. The pwNotForwarding bit is set when none of the preceding failures apply, such as an MTU mismatch failure. This value is applicable only if the peer is using the pseudowire status signaling method to indicate faults. pwNotForwarding — Pseudowire not forwarding lacIngressFault Local — Attachment circuit RX fault lacEgresssFault Local — Attachment circuit TX fault psnIngressFault Local — PSN-facing PW RX fault psnEgressFault Local — PSN-facing PW TX fault pwFwdingStandby — Pseudowire in standby mode |
|
Max IPv4 Routes |
Maximum IPv4 routes configured for use with the service. |
|
Last Changed |
The date and time of the most recent management-initiated change. |
|
Dot1Q Ethertype |
The dot1q Ethertype used by the SAP. |
|
Ingr IP Fltr-Id |
The policy ID of the IP filter applied at ingress. |
|
Ingr Mac Fltr-Id |
The policy ID of the MAC filter applied at ingress. |
|
Egr IP Fltr-Id |
The policy ID of the IP filter applied at egress. |
|
Egr Mac Fltr-Id |
The policy ID of the MAC filter applied at egress. |
|
tod-suite |
The TOD suite applied for use by this SAP. |
|
rate |
Specifies the SAP aggregate rate configured for the aggregate policer/meter used by this SAP. |
|
burst |
Specifies the burst to be used with SAP aggregate policer/meter used by this SAP. |
|
Classifiers Allocated |
Number of SAP ingress QoS resources allocated for use by this SAP. |
|
Classifiers Used |
Number of SAP ingress QoS resources in use by this SAP. |
|
Meters Allocated |
Number of SAP ingress meter resources allocated for use by this SAP. This is set to half the number of classifiers allocated to this SAP. |
|
Meters Used |
Number of SAP ingress meters in use. |
|
Ingress Stats |
The number of received packets/octets for this SAP. |
|
Egress Stats |
The number of packets/octets forwarded out of this SAP. |
|
Ingress Drop Stats |
Number of packets/octets dropped by the system. |
|
Extra-Tag Drop Stats |
Number of packets received with the count of VLAN tags exceeding the count of VLAN tags implied by the SAP encapsulation. |
|
Ingress Meter 1 |
The index of the ingress QoS meter of this SAP. |
|
For. InProf |
Number of in-profile packets/octets received on this SAP. |
|
For. OutProf |
Number of out-of-profile packets/octets received on this SAP. |
|
If Name |
IP interface name assigned by user. |
|
Protocols |
Protocols enabled for use on this interface. |
|
Oper (v4/v6) |
Operational status of this interface for IPv4 and IPv6. |
|
IP Addr/mask |
IPv4 address and mask assigned to this interface. |
|
Address Type |
Whether the address is a primary or secondary address. |
|
Broadcast Address |
Type of broadcast address used: host-ones or all-ones. |
|
If Index |
The interface index assigned by the system. It is used with SNMP IfTable. |
|
Virt. If Index |
The interface index assigned by the system. It is used with SNMP. |
|
Last Oper Chg |
Timestamp associated with the last operational change. |
|
Global If Index |
This is the system wide Interface index allotted by the system. |
|
If Type |
Network — The IP interface is a network/core IP interface. Service — The IP interface is a service IP interface. |
|
SNTP B.Cast |
Specifies whether SNTP broadcast client mode is enabled or disabled. |
|
Arp Timeout |
Specifies the timeout for an ARP entry learned on the interface. |
|
IP Oper MTU |
The actual largest service frame size (in octets) that can be transmitted through the port to the far-end router, without requiring the packet to be fragmented. |
|
LdpSyncTimer |
Specifies the value used for IGP-LDP synchronization. |
|
Redirects |
Specifies the rate for ICMP redirect messages. |
|
Unreachables |
Specifies the rate for ICMP unreachable messages. |
|
TTL Expired |
Specifies the rate for ICMP TTL messages. |
|
MAC Address |
Specifies the 48-bit IEEE 802.3 MAC address. |
authentication
show>service>id
Supported on all 7210 SAS platforms as described in this document
Commands in this context display subscriber authentication information.
statistics [policy name] [sap sap-id]
show>service>id>authentication
Supported on all 7210 SAS platforms as described in this document
This command displays session authentication statistics for the service.
Specifies the subscriber authentication policy statistics to display.
Specifies the SAP ID statistics to display. See Common CLI command descriptions for command syntax.
The following output is an example of service ID statistics information.
Sample output*A:ALA-1# show service id 11 authentication statistics
===============================================================
Authentication statistics
===============================================================
Interface / SAP Authentication Authentication
Successful Failed
---------------------------------------------------------------
abc-11-90.1.0.254 1582 3
---------------------------------------------------------------
Number of entries: 1
===============================================================
*A:ALA-1#arp [ip-address] | [mac ieee-address] | [sap sap-id] | [interface ip-int-name] [sdp sdp-id:vc-id] [summary]
show>service>id
Supported on all 7210 SAS platforms as described in this document
This command displays the ARP table for the IES instance.
Displays only ARP entries in the ARP table with the specified IP address.
Displays only ARP entries in the ARP table with the specified 48-bit MAC address. The MAC address can be expressed in the form aa:bb:cc:dd:ee:ff or aa-bb-cc-dd-ee-ff where aa, bb, cc, dd, ee and ff are hexadecimal numbers.
Displays SAP information for the specified SAP ID. See Common CLI command descriptions for command syntax.
Specifies matching service ARP entries associated with the specified IP interface.
Specifies the IP address of the interface for which to display matching ARP entries.
Specifies the IP interface name for which to display matching ARPs.
The following output is an example of ARP information, and Table: Output fields: service ID ARP describes the output fields.
Sample output*A:ALA-12# show service id 2 arp
==============================================================================
ARP Table
==============================================================================
IP Address MAC Address Type Age Interface Port
------------------------------------------------------------------------------
10.11.1.1 00:03:fa:00:08:22 Other 00:00:00 ies-100-190.11.1 1/1/11:0
==============================================================================
*A:ALA-12# | Label | Description |
|---|---|
|
Service ID |
The service ID number. |
|
MAC |
The specified MAC address. |
|
Source-Identifier |
The location the MAC is defined. |
|
Type |
Static FDB entries created by management. |
|
Learned Dynamic entries created by the learning process. |
|
|
OAM Entries created by the OAM process. |
|
|
Age |
The time elapsed after the service was enabled. |
|
Interface |
The interface applied to the service. |
|
Port |
The port where the SAP is applied. |
base
show>service>id
Supported on all 7210 SAS platforms as described in this document
This command displays basic information about the service ID, including service type, description, SAPs, and SDPs.
The following output is an example of basic service information, and Table: Output fields: service ID base describes the output fields.
Sample output*A:ALA-12# show service id 1 base
===============================================================================
Service Basic Information
===============================================================================
Service Id : 1 Vpn Id : 0
Service Type : VPRN
Customer Id : 1
Last Status Change: 02/01/2007 09:11:39
Last Mgmt Change : 02/01/2007 09:11:46
Admin State : Up Oper State : Down
Route Dist. : 10001:1
AS Number : 10000 Router Id : 10.10.10.103
ECMP : Enabled ECMP Max Routes : 8
Max Routes : No Limit Auto Bind : LDP
Vrf Target : target:10001:1
Vrf Import : vrfImpPolCust1
Vrf Export : vrfExpPolCust1
SAP Count : 1 SDP Bind Count : 18
------------------------------------------------------------------------------
Service Access & Destination Points
------------------------------------------------------------------------------
Identifier Type AdmMTU OprMTU Adm Opr
------------------------------------------------------------------------------
sap:1/1/7:0 q-tag 1518 1518 Up Up
sdp:10:1 M(10.20.1.3) TLDP 4462 4462 Up TLDP Down
sdp:20:1 M(10.20.1.4) TLDP 4462 4462 Up TLDP Down
sdp:30:1 M(10.20.1.5) TLDP 4462 4462 Up TLDP Down
sdp:40:1 M(10.20.1.20) TLDP 1534 4462 Up Up
sdp:200:1 M(10.20.1.30) TLDP 1514 4462 Up Up
sdp:300:1 M(10.20.1.31) TLDP 4462 4462 Up TLDP Down
sdp:500:1 M(10.20.1.50) TLDP 4462 4462 Up TLDP Down
==============================================================================
*A:ALA-12# | Label | Description |
|---|---|
|
Service Id |
The service identifier. |
|
Vpn Id |
Specifies the VPN ID assigned to the service. |
|
Service Type |
Specifies the type of service. |
|
Description |
Generic information about the service. |
|
Customer Id |
The customer identifier. |
|
Last Mgmt Change |
The date and time of the most recent management-initiated change to this customer. |
|
Adm |
The configured state of the service. |
|
Oper |
The operating state of the service. |
|
Mtu |
The largest frame size (in octets) that the service can handle. |
|
Def. Mesh VC Id |
This object is only valid in services that accept mesh SDP bindings. It is used to validate the VC ID portion of each mesh SDP binding defined in the service. |
|
SAP Count |
The number of SAPs defined on the service. |
|
SDP Bind Count |
The number of SDPs bound to the service. |
|
Identifier |
Specifies the service access (SAP) and destination (SDP) points. |
|
Type |
Specifies the signaling protocol used to obtain the ingress and egress labels used in frames transmitted and received on the SDP. |
|
AdmMTU |
Specifies the configured largest service frame size (in octets) that can be transmitted through this SDP to the far-end ESR, without requiring the packet to be fragmented. |
|
OprMTU |
Specifies the actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end ESR, without requiring the packet to be fragmented. |
|
Opr |
The operating state of the SDP. |
statistics [sap sap-id]
statistics [sdp sdp-id:vc-id]
statistics [interface interface-name]
show>service>id>dhcp
Supported on all 7210 SAS platforms as described in this document
This command displays DHCP statistics information.
Specifies the physical port identifier portion of the SAP definition. See Common CLI
Command Descriptions on page 973 for command syntax.
Specifies the SDP identifier.
Specifies the virtual circuit ID on the SDP ID for which to display information.
Displays information for the specified IP interface.
The following output is an example of DHCP statistics information, and Table: Output fields: DHCP statistics describes the output fields.
Sample outputA:sim1# show service id 11 dhcp statistics
================================================================
DHCP Global Statistics, service 11
================================================================
Rx Packets : 32
Tx Packets : 12
Rx Malformed Packets : 0
Rx Untrusted Packets : 0
Client Packets Discarded : 0
Client Packets Relayed : 11
Client Packets Snooped : 21
Server Packets Discarded : 0
Server Packets Relayed : 0
Server Packets Snooped : 0
================================================================
A:sim1#| Label | Description |
|---|---|
|
Received Packets |
The number of packets received from the DHCP clients. |
|
Transmitted Packets |
The number of packets transmitted to the DHCP clients. |
|
Received Malformed Packets |
The number of corrupted and invalid packets received from the DHCP clients. |
|
Received Untrusted Packets |
The number of untrusted packets received from the DHCP clients. In this case, a frame is dropped because of the client sending a DHCP packet with Option 82 filled in before ‟trust” is set under the DHCP interface command. |
|
Client Packets Discarded |
The number of packets received from the DHCP clients that were discarded. |
|
Client Packets Relayed |
The number of packets received from the DHCP clients that were forwarded. |
|
Client Packets Snooped |
The number of packets received from the DHCP clients that were snooped. |
|
Server Packet Discarded |
The number of packets received from the DHCP server that were discarded. |
|
Server Packets Relayed |
The number of packets received from the DHCP server that were forwarded. |
|
Server Packets Snooped |
The number of packets received from the DHCP server that were snooped. |
interface [ip-address | ip-int-name] [detail]
show>service>id
Supported on all 7210 SAS platforms as described in this document
This command displays information for the IP interfaces associated with the service.
If no optional parameters are specified, a summary of all IP interfaces associated with the service are displayed.
Specifies the IP address of the interface for which to display information.
Specifies the IP interface name, up to 32 characters, for which to display information.
Displays detailed IP interface information.
The following output is an example of service interface information, and Table: Output fields: service ID interface describes the output fields.
Sample output*A:ALA-12# show service id 321 interface
===============================================================================
Interface Table
===============================================================================
Interface-Name Type IP-Address Adm Opr Type
-------------------------------------------------------------------------------
test Pri 10.11.1.1/24 Up Up IES
-------------------------------------------------------------------------------
Interfaces : 1
===============================================================================
*A:ALA-12#
A:ALA-49# show service id 88 interface detail
===============================================================================
Interface Table
===============================================================================
Interface
-------------------------------------------------------------------------------
If Name : Sector A
Admin State : Up Oper State : Down
Protocols : None
IP Addr/mask : Not Assigned
-------------------------------------------------------------------------------
Details
-------------------------------------------------------------------------------
Description :
If Index : 26 Virt. If Index : 26
SAP Id : 71/1/1.2.2
TOS Marking : Untrusted If Type : IES
SNTP B.Cast : False IES ID : 88
MAC Address : Not configured. Arp Timeout : 14400
IP MTU : 1500 ICMP Mask Reply : True
Arp Populate : Disabled
Cflowd : None
Proxy ARP Details
Proxy ARP : Enabled Local Proxy ARP : Disabled
Policies : ProxyARP
DHCP Details
Admin State : Up Lease Populate : 0
Action : Keep Trusted : Disabled
ICMP Details
Redirects : Number - 100 Time (seconds) - 10
Unreachables : Number - 100 Time (seconds) - 10
TTL Expired : Number - 100 Time (seconds) - 10
-------------------------------------------------------------------------------
Interface
-------------------------------------------------------------------------------
If Name : test
Admin State : Up Oper State : Down
Protocols : None
IP Addr/mask : Not Assigned
-------------------------------------------------------------------------------
Details
-------------------------------------------------------------------------------
Description :
If Index : 27 Virt. If Index : 27
SAP Id : 101/1/2:0
TOS Marking : Untrusted If Type : IES
SNTP B.Cast : False IES ID : 88
MAC Address : Not configured. Arp Timeout : 14400
Arp Populate : Disabled
Proxy ARP Details
Proxy ARP : Disabled Local Proxy ARP : Disabled
ICMP Details
Redirects : Number - 100 Time (seconds) - 10
Unreachables : Number - 100 Time (seconds) - 10
TTL Expired : Number - 100 Time (seconds) - 10
-------------------------------------------------------------------------------
Interfaces : 2
===============================================================================
A:ALA-49#| Label | Description |
|---|---|
|
Interface-Name |
The name of the interface. |
|
Type |
Specifies the interface type. |
|
IP-Address |
Specifies the IP address/IP subnet/broadcast address of the interface. |
|
Adm |
The configured state of the interface. |
|
Opr |
The operating state of the interface. |
|
Interface |
|
|
If Name |
The name of the interface. |
|
Admin State |
The configured state of the interface. |
|
Oper State |
The operating state of the interface. |
|
IP Addr/mask |
Specifies the IP address/IP subnet/broadcast address of the interface. |
|
Details |
|
|
If Index |
The index corresponding to this interface. The primary index is 1. For example, all interfaces are defined in the Base virtual router context. |
|
If Type |
Specifies the interface type. |
|
Port Id |
Specifies the SAP port ID. |
|
SNTP B.Cast |
Specifies whether SNTP broadcast client mode is enabled or disabled. |
|
Arp Timeout |
Specifies the timeout for an ARP entry learned on the interface. |
|
MAC Address |
Specifies the 48-bit IEEE 802.3 MAC address. |
|
ICMP Mask Reply |
Specifies whether ICMP mask reply is enabled or disabled. |
|
ICMP Details |
|
|
Redirects |
Specifies the rate for ICMP redirect messages. |
|
Unreachables |
Specifies the rate for ICMP unreachable messages. |
|
TTL Expired |
Specifies the rate for ICMP TTL messages. |
sap sap-id [detail]
show>service>id
Supported on all 7210 SAS platforms as described in this document
This command displays information for the SAPs associated with the service.
If no optional parameters are specified, a summary of all associated SAPs is displayed.
Specifies the ID that displays SAPs for the service. See Common CLI command descriptions for command syntax.
Displays detailed information for the SAP.
The following output is an example of SAP information, and Table: Output fields: service ID SAP describes the output fields.
Sample output*A:ALA-12# show service id 321 sap 1/1/4:0
===============================================================================
Service Access Points(SAP)
===============================================================================
Service Id : 321
SAP : 1/1/4:0 Encap : q-tag
Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100
Admin State : Up Oper State : Down
Flags : PortOperDown
SapIngressQoSMismatch
Last Status Change : 02/03/2007 12:58:37
Last Mgmt Change : 02/03/2007 12:59:10
Admin MTU : 1518 Oper MTU : 1518
Ingress qos-policy : 100 Egress qos-policy : 1
Ingress Filter-Id : n/a Egress Filter-Id : n/a
Multi Svc Site : None
Acct. Pol : None Collect Stats : Disabled
===============================================================================
*A:ALA-12#
*A:ALA-12# show service id 321 sap 1/1/4:0 detail
===============================================================================
Service Access Points(SAP)
===============================================================================
Service Id : 321
SAP : 1/1/4:0 Encap : q-tag
Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100
Admin State : Up Oper State : Down
Flags : PortOperDown
SapIngressQoSMismatch
Last Status Change : 02/03/2007 12:58:37
Last Mgmt Change : 02/03/2007 12:59:10
Admin MTU : 1518 Oper MTU : 1518
Ingress qos-policy : 100 Egress qos-policy : 1
Ingress Filter-Id : n/a Egress Filter-Id : n/a
Multi Svc Site : None
Acct. Pol : None Collect Stats : Disabled
-------------------------------------------------------------------------------
Sap Statistics
-------------------------------------------------------------------------------
Packets Octets
Forwarding Engine Stats
Dropped : 0 0
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Off. Uncolor : 0 0
Queueing Stats(Egress QoS Policy 1)
Dro. InProf : 0 0
Dro. OutProf : 0 0
For. InProf : 0 0
For. OutProf : 0 0
-------------------------------------------------------------------------------
=============================================================================
*A:ALA-12#
*A:dut-a>config>log# /show service id 100 sap 1/1/22:100 sap-stats
===============================================================================
Service Access Points(SAP)
===============================================================================
Service Id : 100
SAP : 1/1/22:100 Encap : q-tag
Description : (Not Specified)
Admin State : Up Oper State : Up
Flags : None
Last Status Change : 02/17/2016 10:24:49
Last Mgmt Change : 02/17/2016 10:24:46
-------------------------------------------------------------------------------
Ingress QoS Classifier Usage
-------------------------------------------------------------------------------
Classifiers Allocated: 2 Meters Allocated : 1
Classifiers Used : 1 Meters Used : 1
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Sap Statistics
-------------------------------------------------------------------------------
Packets Octets
Ingress Stats: 0 0
Egress Stats: 76990984 116872316748
Ingress Drop Stats: 0 0
Extra-Tag Drop Stats: n/a n/a
-------------------------------------------------------------------------------
Sap per Meter stats (in/out counter mode)
-------------------------------------------------------------------------------
Packets Octets
Ingress Meter 1
For. InProf : 0 0
For. OutProf : 0 0
-------------------------------------------------------------------------------
Egr sap agg-meter stats
-------------------------------------------------------------------------------
Packets Octets
Drop : 385943060 73232696583
Forward : 74671326 14168884298
-------------------------------------------------------------------------------
===============================================================================
*A:dut-a>| Label | Description |
|---|---|
|
Service Id |
The service identifier. |
|
SAP |
The SAP and qtag. |
|
Encap |
The encapsulation type of the SAP. |
|
Ethertype |
Specifies an Ethernet type II Ethertype value. |
|
Admin State |
The administrative state of the SAP. |
|
Oper State |
The operating state of the SAP. |
|
Flags |
Specifies the conditions that affect the operating status of this SAP. Display output includes: ServiceAdminDown, SapAdminDown, InterfaceAdminDown, PortOperDown, PortMTUTooSmall, L2OperDown, SapIngressQoSMismatch, SapEgressQoSMismatch,RelearnLimitExceeded, RxProtSrcMac, ParentIfAdminDown, NoSapIpipeCeIpAddr, TodResourceUnavail, TodMssResourceUnavail, SapParamMismatch, CemSapNoEcidOrMacAddr, ServiceMTUTooSmall, SapIngressNamedPoolMismatch, SapEgressNamedPoolMismatch, NoSapEpipeRingNode. |
|
Last Status Change |
Specifies the time of the most recent operating status change to this SAP. |
|
Last Mgmt Change |
Specifies the time of the most recent management-initiated change to this SAP. |
|
Admin MTU |
The configured largest service frame size (in octets) that can be transmitted through the SAP to the far-end router without requiring the packet to be fragmented. |
|
Oper MTU |
The actual largest service frame size (in octets) that can be transmitted through the SAP to the far-end router, without requiring the packet to be fragmented. |
|
Ingress qos-policy |
The ingress QoS policy ID assigned to the SAP. |
|
Egress qos-policy |
The egress QoS policy ID assigned to the SAP. |
|
Ingress Filter-Id |
The ingress filter policy ID assigned to the SAP. |
|
Table-based |
Indicates the use of table-based resource classification: Enabled (table-based) or Disabled (CAM-based). |
|
Egress Filter-Id |
The egress filter policy ID assigned to the SAP. |
|
Acct. Pol |
The accounting policy ID assigned to the SAP. |
|
Collect Stats |
Specifies whether collect stats is enabled. |
|
Dropped |
The number of packets and octets dropped because of SAP state, ingress MAC or IP filter, same segment discard, bad checksum, and so on. |
|
Off. HiPrio |
The number of high priority packets and octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip. |
|
Off. LowPrio |
The number of low priority packets and octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip. |
|
Off. Uncolor |
The number of uncolored packets and octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip. |
|
Dro. HiPrio |
The number of high priority packets and octets, as determined by the SAP ingress QoS policy, dropped by the Qchip because of MBS exceeded, buffer pool limit exceeded, and so on. |
|
Dro. LowPrio |
The number of low priority packets and octets, as determined by the SAP ingress QoS policy, dropped by the Qchip because of MBS exceeded, buffer pool limit exceeded, and so on. |
|
For. InProf |
The number of in-profile packets and octets (rate below CIR) forwarded by the ingress Qchip. |
|
For. OutProf |
The number of out-of-profile packets and octets discarded by the egress Qchip because of MBS exceeded, buffer pool limit exceeded, and so on. |
|
Dro. InProf |
The number of in-profile packets and octets discarded by the egress Qchip because of MBS exceeded, buffer pool limit exceeded, and so on. |
|
Dro. OutProf |
The number of out-of-profile packets and octets discarded by the egress Qchip because of MBS exceeded, buffer pool limit exceeded, and so on. |
|
For. InProf |
The number of in-profile packets and octets (rate below CIR) forwarded by the egress Qchip. |
|
For. OutProf |
The number of out-of-profile packets and octets (rate above CIR) forwarded by the egress Qchip. |
|
Ingress TD Profile |
The profile ID applied to the ingress SAP. |
|
Egress TD Profile |
The profile ID applied to the egress SAP. |
|
Alarm Cell Handling |
The indication that OAM cells are being processed. |
|
AAL-5 Encap |
The AAL-5 encapsulation type. |
sdp [sdp-id | far-end ip-addr] [detail]
show>service>id
Supported on all 7210 SAS platforms as described in this document
This command displays information for the SDPs associated with the service. If no optional parameters are specified, a summary of all associated SDPs is displayed.
Displays only information for the specified SDP ID.
Displays only SDPs matching with the specified far-end IP address.
Displays detailed SDP information.
The following output is an example of SDP information, and Table: Output fields: service ID SDP describes the output fields.
Sample outputA:Dut-A# show service id 1 sdp detail
===============================================================================
Services: Service Destination Points Details
===============================================================================
Sdp Id 1:1 -(10.20.1.2)
-------------------------------------------------------------------------------
Description : Default sdp description
SDP Id : 1:1 Type : Spoke
VC Type : Ether VC Tag : n/a
Admin Path MTU : 0 Oper Path MTU : 9186
Far End : 10.20.1.2 Delivery : MPLS
Admin State : Up Oper State : Up
Acct. Pol : None Collect Stats : Disabled
Ingress Label : 2048 Egress Label : 2048
Ing mac Fltr : n/a Egr mac Fltr : n/a
Ing ip Fltr : n/a Egr ip Fltr : n/a
Ing ipv6 Fltr : n/a Egr ipv6 Fltr : n/a
Admin ControlWord : Not Preferred Oper ControlWord : False
Last Status Change : 05/31/2007 00:45:43 Signaling : None
Last Mgmt Change : 05/31/2007 00:45:43
Class Fwding State : Up
Flags : None
Peer Pw Bits : None
Peer Fault Ip : None
Peer Vccv CV Bits : None
Peer Vccv CC Bits : None
Max Nbr of MAC Addr: No Limit Total MAC Addr : 0
Learned MAC Addr : 0 Static MAC Addr : 0
MAC Learning : Enabled Discard Unkwn Srce: Disabled
MAC Aging : Enabled
L2PT Termination : Disabled BPDU Translation : Disabled
MAC Pinning : Disabled
KeepAlive Information :
Admin State : Disabled Oper State : Disabled
Hello Time : 10 Hello Msg Len : 0
Max Drop Count : 3 Hold Down Time : 10
Statistics :
I. Fwd. Pkts. : 0 I. Dro. Pkts. : 0
I. Fwd. Octs. : 0 I. Dro. Octs. : 0
E. Fwd. Pkts. : 0 E. Fwd. Octets : 0
MCAC Policy Name :
MCAC Max Unconst BW: no limit MCAC Max Mand BW : no limit
MCAC In use Mand BW: 0 MCAC Avail Mand BW: unlimited
MCAC In use Opnl BW: 0 MCAC Avail Opnl BW: unlimited
Associated LSP LIST :
Lsp Name : A_B_1
Admin State : Up Oper State : Up
Time Since Last Tr*: 00h26m35s
Lsp Name : A_B_2
Admin State : Up Oper State : Up
Time Since Last Tr*: 00h26m35s
Lsp Name : A_B_3
Admin State : Up Oper State : Up
Time Since Last Tr*: 00h26m34s
Lsp Name : A_B_4
Admin State : Up Oper State : Up
Time Since Last Tr*: 00h26m34s
Lsp Name : A_B_5
Admin State : Up Oper State : Up
Time Since Last Tr*: 00h26m34s
Lsp Name : A_B_6
Admin State : Up Oper State : Up
Time Since Last Tr*: 00h26m34s
Lsp Name : A_B_7
Admin State : Up Oper State : Up
Time Since Last Tr*: 00h26m34s
Lsp Name : A_B_8
Admin State : Up Oper State : Up
Time Since Last Tr*: 00h26m35s
Lsp Name : A_B_9
Admin State : Up Oper State : Up
Time Since Last Tr*: 00h26m34s
Lsp Name : A_B_10
Admin State : Up Oper State : Up
Time Since Last Tr*: 00h26m34s
-------------------------------------------------------------------------------
Class-based forwarding :
-------------------------------------------------------------------------------
Class forwarding : enabled
Default LSP : A_B_10 Multicast LSP : A_B_9
===============================================================================
FC Mapping Table
===============================================================================
FC Name LSP Name
-------------------------------------------------------------------------------
af A_B_3
be A_B_1
ef A_B_6
h1 A_B_7
h2 A_B_5
l1 A_B_4
l2 A_B_2
nc A_B_8
===============================================================================
Stp Service Destination Point specifics
-------------------------------------------------------------------------------
Mac Move : Blockable
Stp Admin State : Up Stp Oper State : Down
Core Connectivity : Down
Port Role : N/A Port State : Forwarding
Port Number : 2049 Port Priority : 128
Port Path Cost : 10 Auto Edge : Enabled
Admin Edge : Disabled Oper Edge : N/A
Link Type : Pt-pt BPDU Encap : Dot1d
Root Guard : Disabled Active Protocol : N/A
Last BPDU from : N/A
Designated Bridge : N/A Designated Port Id: 0
Fwd Transitions : 0 Bad BPDUs rcvd : 0
Cfg BPDUs rcvd : 0 Cfg BPDUs tx : 0
TCN BPDUs rcvd : 0 TCN BPDUs tx : 0
RST BPDUs rcvd : 0 RST BPDUs tx : 0
-------------------------------------------------------------------------------
Number of SDPs : 1
-------------------------------------------------------------------------------
* indicates that the corresponding row element may have been truncated.
-------------------------------------------------------------------------------
A:Dut-A# | Label | Description |
|---|---|
|
Sdp Id |
The SDP identifier. |
|
Type |
Indicates whether the SDP is a spoke or a mesh. |
|
Split Horizon Group |
Name of the split horizon group that the SDP belongs to. |
|
VC Type |
Displays the VC type: ether or vlan. |
|
VC Tag |
Displays the explicit dot1Q value used when encapsulating to the SDP far end. |
|
I. Lbl |
The VC label used by the far-end device to send packets to this device in this service by the SDP. |
|
Admin Path MTU |
The operating path MTU of the SDP is equal to the admin path MTU (when one is set) or the dynamically computed tunnel MTU, when no admin path MTU is set (the default case). |
|
Oper Path MTU |
The actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented. |
|
Far End |
Specifies the IP address of the remote end of the MPLS tunnel defined by this SDP. |
|
Delivery |
Specifies the type of delivery used by the SDP: MPLS. |
|
Admin State |
The administrative state of this SDP. |
|
Oper State |
The operational state of this SDP. |
|
Ingress Label |
The label used by the far-end device to send packets to this device in this service by this SDP. |
|
Egress Label |
The label used by this device to send packets to the far-end device in this service by the SDP. |
|
Last Changed |
The date and time of the most recent change to the SDP. |
|
Signaling |
Specifies the signaling protocol used to obtain the ingress and egress labels used in frames transmitted and received on this SDP. |
|
Admin State |
The administrative state of the keepalive process. |
|
Oper State |
The operational state of the keepalive process. |
|
Hello Time |
Specifies how often the SDP echo request messages are transmitted on this SDP. |
|
Max Drop Count |
Specifies the maximum number of consecutive SDP echo request messages that can be unacknowledged before the keepalive protocol reports a fault. |
|
Hello Msg Len |
Specifies the length of the SDP echo request messages transmitted on this SDP. |
|
Hold Down Time |
Specifies the amount of time to wait before the keepalive operating status is eligible to enter the alive state. |
|
I. Fwd. Pkts. |
Specifies the number of forwarded ingress packets. |
|
I. Dro. Pkts. |
Specifies the number of dropped ingress packets. |
|
E. Fwd. Pkts. |
Specifies the number of forwarded egress packets. |
|
Associated LSP List |
When the SDP type is MPLS, a list of LSPs used to reach the far-end router displays. All the LSPs in the list must terminate at the IP address specified in the far-end field. |
aggregate [active]
show>router
Supported on all 7210 SAS platforms as described in this document
This command displays aggregated routes.
Keyword that filters out inactive aggregates.
The following output is an example of aggregate route information, and Table: Output fields: router aggregate describes the output fields.
Sample output*A:ALA-12# show router 3 aggregate
==============================================================================
Aggregates (Service: 3)
==============================================================================
Prefix Summary AS Set Aggr AS Aggr IP-Address State
------------------------------------------------------------------------------
------------------------------------------------------------------------------
No. of Aggregates: 0
-----------------------------------------------------------
*A:ALA-12#| Label | Definition |
|---|---|
|
Prefix |
Displays the destination address of the aggregate route in dotted-decimal notation. |
|
Summary |
Specifies whether the aggregate or more specific components are advertised. |
|
AS Set |
Displays an aggregate where the path advertised for the route consists of all elements contained in all paths that are being summarized. |
|
Aggr AS |
Displays the aggregator path attribute to the aggregate route. |
|
Aggr IP-Address |
The IP address of the aggregated route. |
|
State |
The operational state of the aggregated route. |
|
No. of Aggregates |
The total number of aggregated routes. |
arp [ip-address | ip-int-name | mac ieee-mac-addr]
show>router
Supported on all 7210 SAS platforms as described in this document
This command displays the router ARP table sorted by IP address.
If no command line options are specified, all ARP entries are displayed.
Displays only ARP entries associated with the specified IP address.
Displays only ARP entries associated with the specified IP interface name.
Displays only ARP entries associated with the specified MAC address.
The following output is an example of router ARP table information, and Table: Output fields: ARP table describes the output fields.
Sample output*A:ALA-12# show router 3 arp
===============================================================================
ARP Table (Service: 3)
===============================================================================
IP Address MAC Address Expiry Type Interface
-------------------------------------------------------------------------------
10.10.10.103 04:67:ff:00:00:01 00h00m00s Oth system
10.10.4.3 00:00:00:00:00:00 00h00m00s Oth ALA-1-2
10.10.5.3 00:00:00:00:00:00 00h00m00s Oth ALA-1-3
10.10.7.3 00:00:00:00:00:00 00h00m00s Oth ALA-1-5
10.10.0.16 00:00:00:00:00:00 00h00m00s Oth bozo
10.10.3.3 00:00:00:00:00:00 00h00m00s Oth gizmo
10.10.2.3 00:00:00:00:00:00 00h00m00s Oth hobo
10.10.1.17 00:00:00:00:00:00 00h00m00s Oth int-cflowd
10.0.0.92 00:00:00:00:00:00 04h00m00s Dyn to-104
10.0.0.103 04:67:01:01:00:01 00h00m00s Oth[I] to-104
10.0.0.104 04:68:01:01:00:01 03h59m49s Dyn[I] to-104
10.10.36.2 00:00:00:00:00:00 00h00m00s Oth tuesday
192.168.2.98 00:03:47:c8:b4:86 00h14m37s Dyn[I] management
192.168.2.103 00:03:47:dc:98:1d 00h00m00s Oth[I] management
-------------------------------------------------------------------------------
No. of ARP Entries: 14
===============================================================================
*A:ALA-12#
*A:ALA-12# show router 3 arp 10.10.0.3
===============================================================================
ARP Table
===============================================================================
IP Address MAC Address Expiry Type Interface
-------------------------------------------------------------------------------
10.10.0.3 04:5d:ff:00:00:00 00:00:00 Oth system
===============================================================================
*A:ALA-12#
*A:ALA-12# show router 3 arp to-ser1
===============================================================================
ARP Table
===============================================================================
IP Address MAC Address Expiry Type Interface
-------------------------------------------------------------------------------
10.10.13.1 04:5b:01:01:00:02 03:53:09 Dyn to-ser1
===============================================================================
*A:ALA-12#| Label | Description |
|---|---|
|
IP Address |
The IP address of the ARP entry. |
|
MAC Address |
The MAC address of the ARP entry. |
|
Expiry |
The age of the ARP entry. |
|
Type |
Dyn The ARP entry is a dynamic ARP entry. |
|
Inv The ARP entry is an inactive static ARP entry (invalid). |
|
|
Oth The ARP entry is a local or system ARP entry. |
|
|
Sta The ARP entry is an active static ARP entry. |
|
|
Interface |
The IP interface name associated with the ARP entry. |
|
No. of ARP Entries |
The number of ARP entries displayed in the list. |
damping [ip-prefix/mask | ip-address] [detail]
damping [damp-type] [detail]
show>router>bgp
Supported on all 7210 SAS platforms as described in this document
This command displays BGP routes with have been dampened because of route flapping. This command can be entered with or without a route parameter.
Include the detail keyword to display more information.
When only the command is entered (without any parameters included except detail), all dampened routes are listed.
When a parameter is specified, the matching route or routes are listed.
When a decayed, history, or suppressed keyword is specified, only those types of dampened routes are listed.
Displays damping information for the specified IP prefix and mask length.
Displays the damping entry for the best match route for the specified IP address.
Displays the damping type for the specified IP address.
Displays damping entries that are decayed but are not suppressed.
Displays damping entries that are withdrawn but have history.
Displays damping entries suppressed because of route damping.
Displays detailed information.
The following output is an example of BGP damping, and Table: Output fields: BGP damping describes the output fields.
Sample output*A:ALA-12# show router 3 bgp damping
==============================================================================
BGP Router ID : 10.0.0.14 AS : 65206 Local AS : 65206
==============================================================================
Legend -
Status codes : u - used, s - suppressed, h - history, d - decayed, * - valid
Origin codes : i - IGP, e - EGP, ? - incomplete, - best
==============================================================================
BGP Damped Routes
==============================================================================
Flag Network From Reuse AS-Path
------------------------------------------------------------------------------
ud*i 10.149.7.0/24 10.0.28.1 00h00m00s 60203 65001 19855 3356
1239 22406
si 19.155.6.0/23 10.0.28.1 00h43m41s 60203 65001 19855 3356
2914 7459
si 10.155.8.0/22 10.0.28.1 00h38m31s 60203 65001 19855 3356
2914 7459
si 10.155.12.0/22 10.0.28.1 00h35m41s 60203 65001 19855 3356
2914 7459
si 10.155.22.0/23 10.0.28.1 00h35m41s 60203 65001 19855 3356
2914 7459
si 10.155.24.0/22 10.0.28.1 00h35m41s 60203 65001 19855 3356
2914 7459
si 10.155.28.0/22 10.0.28.1 00h34m31s 60203 65001 19855 3356
2914 7459
si 10.155.40.0/21 10.0.28.1 00h28m24s 60203 65001 19855 3356
7911 7459
si 10.155.48.0/20 10.0.28.1 00h28m24s 60203 65001 19855 3356
7911 7459
ud*i 10.8.140.0/24 10.0.28.1 00h00m00s 60203 65001 19855 3356
4637 17447
ud*i 10.8.141.0/24 10.0.28.1 00h00m00s 60203 65001 19855 3356
4637 17447
ud*i 10.9.0.0/18 10.0.28.1 00h00m00s 60203 65001 19855 3356
3561 9658 6163
. . .
ud*i 10.213.184.0/23 10.0.28.1 00h00m00s 60203 65001 19855 3356
6774 6774 9154
------------------------------------------------------------------------------
*A:ALA-12#
*A:ALA-12# show router 3 bgp damping detail
==============================================================================
BGP Router ID : 10.0.0.14 AS : 65206 Local AS : 65206
==============================================================================
Legend -
Status codes : u - used, s - suppressed, h - history, d - decayed, * -
valid
Origin codes : i - IGP, e - EGP, ? - incomplete, - best
==============================================================================
BGP Damped Routes
==============================================================================
------------------------------------------------------------------------------
Network : 10.149.7.0/24
------------------------------------------------------------------------------
Network : 10.149.7.0/24 Peer : 10.0.28.1
NextHop : 10.0.28.1 Reuse time : 00h00m00s
Peer AS : 60203 Peer Router-Id : 32.32.27.203
Local Pref : none
Age : 00h22m09s Last update : 02d00h58m
FOM Present : 738 FOM Last upd. : 2039
Number of Flaps : 2 Flags : ud*i
Path : 60203 65001 19855 3356 1239 22406
Applied Policy : default-damping-profile
------------------------------------------------------------------------------
Network : 10.142.48.0/20
------------------------------------------------------------------------------
Network : 10.142.48.0/20 Peer : 10.0.28.1
NextHop : 10.0.28.1 Reuse time : 00h00m00s
Peer AS : 60203 Peer Router-Id : 32.32.27.203
Local Pref : none
Age : 00h00m38s Last update : 02d01h20m
FOM Present : 2011 FOM Last upd. : 2023
Number of Flaps : 2 Flags : ud*i
Path : 60203 65001 19855 3356 3561 5551 1889
Applied Policy : default-damping-profile
------------------------------------------------------------------------------
Network : 10.200.128.0/19
------------------------------------------------------------------------------
Network : 10.200.128.0/19 Peer : 10.0.28.1
NextHop : 10.0.28.1 Reuse time : 00h00m00s
Peer AS : 60203 Peer Router-Id : 32.32.27.203
Local Pref : none
Age : 00h00m38s Last update : 02d01h20m
FOM Present : 2011 FOM Last upd. : 2023
Number of Flaps : 2 Flags : ud*i
Path : 60203 65001 19855 1299 702 1889
Applied Policy : default-damping-profile
------------------------------------------------------------------------------
Network : 10.203.192.0/18
-------------------------------------------------------------------------------
Network : 10.203.192.0/18 Peer : 10.0.28.1
NextHop : 10.0.28.1 Reuse time : 00h00m00s
Peer AS : 60203 Peer Router-Id : 32.32.27.203
Local Pref : none
Age : 00h00m07s Last update : 02d01h20m
FOM Present : 1018 FOM Last upd. : 1024
Number of Flaps : 1 Flags : ud*i
Path : 60203 65001 19855 1299 702 1889
Applied Policy : default-damping-profile
------------------------------------------------------------------------------
*A:ALA-12#
*A:ALA-12# show router 3 bgp damping 10.203.192.0/18 detail
==============================================================================
BGP Router ID : 10.0.0.14 AS : 65206 Local AS : 65206
==============================================================================
Legend -
Status codes : u - used, s - suppressed, h - history, d - decayed, * - valid
Origin codes : i - IGP, e - EGP, ? - incomplete, - best
==============================================================================
BGP Damped Routes 10.203.192.0/18
==============================================================================
Network : 10.203.192.0/18
------------------------------------------------------------------------------
Network : 10.203.192.0/18 Peer : 10.0.28.1
NextHop : 10.0.28.1 Reuse time : 00h00m00s
Peer AS : 60203 Peer Router-Id : 32.32.27.203
Local Pref : none
Age : 00h00m42s Last update : 02d01h20m
FOM Present : 2003 FOM Last upd. : 2025
Number of Flaps : 2 Flags : ud*i
Path : 60203 65001 19855 3356 702 1889
Applied Policy : default-damping-profile
------------------------------------------------------------------------------
Paths : 1
==============================================================================
*A:ALA-12#
*A:ALA-12# show router 3 bgp damping suppressed detail
==============================================================================
BGP Router ID : 10.0.0.14 AS : 65206 Local AS : 65206
==============================================================================
Legend -
Status codes : u - used, s - suppressed, h - history, d - decayed, * - valid
Origin codes : i - IGP, e - EGP, ? - incomplete, - best
==============================================================================
BGP Damped Routes (Suppressed)
==============================================================================
Network : 10.142.48.0/20
------------------------------------------------------------------------------
Network : 10.142.48.0/20 Peer : 10.0.28.1
NextHop : 10.0.28.1 Reuse time : 00h29m22s
Peer AS : 60203 Peer Router-Id : 32.32.27.203
Local Pref : none
Age : 00h01m28s Last update : 02d01h20m
FOM Present : 2936 FOM Last upd. : 3001
Number of Flaps : 3 Flags : si
Path : 60203 65001 19855 3356 702 1889
Applied Policy : default-damping-profile
------------------------------------------------------------------------------
Network : 10.200.128.0/19
------------------------------------------------------------------------------
Network : 10.200.128.0/19 Peer : 10.0.28.1
NextHop : 10.0.28.1 Reuse time : 00h29m22s
Peer AS : 60203 Peer Router-Id : 32.32.27.203
Local Pref : none
Age : 00h01m28s Last update : 02d01h20m
FOM Present : 2936 FOM Last upd. : 3001
Number of Flaps : 3 Flags : si
Path : 60203 65001 19855 3356 702 1889
Applied Policy : default-damping-profile
------------------------------------------------------------------------------
Network : 10.203.240.0/20
------------------------------------------------------------------------------
Network : 10.203.240.0/20 Peer : 10.0.28.1
NextHop : 10.0.28.1 Reuse time : 00h29m22s
Peer AS : 60203 Peer Router-Id : 32.32.27.203
Local Pref : none
Age : 00h01m28s Last update : 02d01h20m
FOM Present : 2936 FOM Last upd. : 3001
Number of Flaps : 3 Flags : si
Path : 60203 65001 19855 3356 702 1889
Applied Policy : default-damping-profile
------------------------------------------------------------------------------
Network : 10.206.0.0/17
------------------------------------------------------------------------------
Network : 10.206.0.0/17 Peer : 10.0.28.1
NextHop : 10.0.28.1 Reuse time : 00h29m22s
Peer AS : 60203 Peer Router-Id : 32.32.27.203
Local Pref : none
Age : 00h01m28s Last update : 02d01h20m
FOM Present : 2936 FOM Last upd. : 3001
Number of Flaps : 3 Flags : si
Path : 60203 65001 19855 3356 702 1889
Applied Policy : default-damping-profile
------------------------------------------------------------------------------
*A:ALA-12#| Label | Description |
|---|---|
|
BGP Router ID |
The local BGP router ID. |
|
AS |
The configured AS number. |
|
Local AS |
The configured or inherited local AS for the specified peer group. If not configured, it is the same value as the AS. |
|
Network |
Route IP prefix and mask length for the route. |
|
Flags |
Legend: Status codes: u- used, s-suppressed, h-history, d-decayed, *-valid. If a * is not present, then the status is invalid. Origin codes: i-IGP, e-EGP, ?-incomplete, >-best |
|
Network |
The IP prefix and mask length for the route. |
|
From |
The originator ID path attribute value. |
|
Reuse time |
The time when a suppressed route can be used again. |
|
AS Path |
The BGP AS path for the route. |
|
Peer |
The router ID of the advertising router. |
|
NextHop |
BGP next hop for the route. |
|
Peer AS |
The AS number of the advertising router. |
|
Peer Router-Id |
The router ID of the advertising router. |
|
Local Pref |
BGP local preference path attribute for the route. |
|
Age |
The time elapsed after the service was enabled. |
|
Last update |
The time when BGP was updated last in second/minute/hour (SS:MM:HH) format. |
|
FOM Present |
The current Figure of Merit (FOM) value. |
|
Number of Flaps |
The number of flaps in the neighbor connection. |
|
Reuse time |
The time when the route can be reused. |
|
Path |
The BGP AS path for the route. |
|
Applied Policy |
The applied route policy name. |
group [name] [detail]
show>router>bgp
Supported on all 7210 SAS platforms as described in this document
This command displays group information for a BGP peer group. This command can be entered with or without parameters.
When this command is entered without a group name, information about all peer groups displays.
When the command is issued with a specific group name, only information pertaining to that specific peer group is displayed.
The ‟State” field displays the BGP group operational state. Other valid states are the following:
Up
BGP global process is configured and running.
Down
BGP global process is administratively shutdown and not running.
Disabled
BGP global process is operationally disabled. The process must be restarted by the operator.
Displays information for the BGP group specified.
Displays detailed information.
The following output is an example of BGP peer group information, and Table: Output fields: BGP group describes the output fields.
Sample output*A:ALA-12# show router 3 bgp group
===============================================================================
BGP Groups
===============================================================================
Group : To_AS_40000
-------------------------------------------------------------------------------
Description : Not Available
Group Type : No Type State : Up
Peer AS : 40000 Local AS : 65206
Local Address : n/a Loop Detect : Ignore
Export Policy : direct2bgp
Hold Time : 90 Keep Alive : 30
Cluster Id : None Client Reflect : Enabled
NLRI : Unicast Preference : 170
List of Peers
- 10.0.0.1 : To_Jukebox
- 10.0.0.12 : Not Available
- 10.0.0.13 : Not Available
- 10.0.0.14 : To_ALA-1
- 10.0.0.15 : To_H-215
Total Peers : 5 Established : 2
===============================================================================
*A:ALA-12#| Label | Description |
|---|---|
|
Group |
BGP group name. |
|
Group Type |
No Type Peer type not configured. |
|
External Peer type configured as external BGP peers. |
|
|
Internal Peer type configured as internal BGP peers. |
|
|
State |
Disabled The BGP peer group has been operationally disabled. |
|
Down The BGP peer group is operationally inactive. |
|
|
Up The BGP peer group is operationally active. |
|
|
Peer AS |
The configured or inherited peer AS for the specified peer group. |
|
Local AS |
The configured or inherited local AS for the specified peer group. |
|
Local Address |
The configured or inherited local address for originating peering for the specified peer group. |
|
Loop Detect |
The configured or inherited loop detect setting for the specified peer group. |
|
Connect Retry |
The configured or inherited connect retry timer value. |
|
Authentication |
|
|
None No authentication is configured. |
|
|
MD5 MD5 authentication is configured. |
|
|
Local Pref |
The configured or inherited local preference value. |
|
MED Out |
The configured or inherited MED value assigned to advertised routes without a MED attribute. |
|
Min Route Advt. |
The minimum amount of time that must pass between route updates for the same IP prefix. |
|
Min AS Originate |
The minimum amount of time that must pass between updates for a route originated by the local router. |
|
Multihop |
The maximum number of router hops a BGP connection can traverse. |
|
Multipath |
The configured or inherited multipath value, determining the maximum number of ECMP routes BGP can advertise to the RTM. |
|
Prefix Limit |
No Limit No route limit assigned to the BGP peer group. |
|
1 to 4294967295 The maximum number of routes BGP can learn from a peer. |
|
|
Passive |
Disabled BGP attempts to establish BGP connections with neighbors in the specified peer group. |
|
Enabled BGP does not actively attempt to establish BGP connections with neighbors in the specified peer group. |
|
|
Next Hop Self |
Disabled BGP is not configured to send only its own IP address as the BGP next hop in route updates to neighbors in the peer group. |
|
Enabled BGP sends only its own IP address as the BGP nexthop in route updates to neighbors in the specified peer group. |
|
|
Aggregator ID 0 |
Disabled BGP is not configured to set the aggregator ID to 0.0.0.0 in all originated route aggregates sent to the neighbor in the peer group. |
|
Enabled BGP is configured to set the aggregator ID to 0.0.0.0 in all originated route aggregates sent to the neighbor in the peer group. |
|
|
Remove Private |
Disabled BGP does not remove all private AS numbers from the AS path attribute in updates sent to the neighbor in the peer group. |
|
Enabled BGP removes all private AS numbers from the AS path attribute in updates sent to the neighbor in the peer group. |
|
|
Damping |
Disabled The peer group is configured not to dampen route flaps. |
|
Enabled The peer group is configured to dampen route flaps. |
|
|
Export Policy |
The configured export policies for the peer group. |
|
Import Policy |
The configured import policies for the peer group. |
|
Hold Time |
The configured hold time setting. |
|
Keep Alive |
The configured keepalive setting. |
|
Cluster Id |
None No cluster ID has been configured. |
|
Client Reflect |
Disabled The BGP route reflector does not reflect routes to this neighbor. |
|
Enabled The BGP route reflector is configured to reflect routes to this neighbor. |
|
|
NLRI |
The type of NLRI information that the specified peer group can accept. |
|
Unicast IPv4 unicast routing information can be carried. |
|
|
Preference |
The configured route preference value for the peer group. |
|
List of Peers |
A list of BGP peers configured under the peer group. |
|
Total Peers |
The total number of peers configured under the peer group. |
|
Established |
The total number of peers that are in an established state. |
neighbor [ip-address [[family family] filter1]]
neighbor [as-number [[family family] filter2]]
show>router>bgp
Supported on all 7210 SAS platforms as described in this document
This command displays BGP neighbor information. This command can be entered with or without parameters. When this command is issued without parameters, information about all BGP peers displays.
When the command is issued with a specific IP address or ASN, only information for that specific peer or peers with the same AS is displayed.
When either received-routes or advertised-routes is specified, the routes received from or sent to the specified peer is listed (see second output example). This information is not available by SNMP.
When either history or suppressed is specified, the routes learned from those peers that either have a history or are suppressed (respectively) are listed.
The ‟State” field displays the BGP peer protocol state. In additional to the standard protocol states, this field can also display the ‟Disabled” operational state, which indicates the peer is operationally disabled and must be restarted by the operator.
Displays the BGP neighbor with the specified IP address.
Specifies the type of routing information to be distributed by the BGP instance.
Specifies route criteria.
Specifies route criteria.
The following outputs are examples of BGP neighbor information, and the associated tables describe the output fields.
Sample output*A:ALA-12# show router 3 bgp neighbor
===============================================================================
BGP Neighbor
===============================================================================
-------------------------------------------------------------------------------
Peer : 10.0.0.15 Group : To_AS_40000
-------------------------------------------------------------------------------
Peer AS : 65205
Peer Address : 10.0.0.15 Peer Port : 0
Local AS : 65206
Local Address : 10.0.0.16 Local Port : 0
Peer Type : External
State : Active Last State : Connect
Last Event : openFail
Last Error : Hold Timer Expire
Hold Time : 90 Keep Alive : 30
Active Hold Time : 0 Active Keep Alive: 0
Cluster Id : None
Preference : 170 Num of Flaps : 0
Recd. Prefixes : 0 Active Prefixes : 0
Recd. Paths : 0 Suppressed Paths : 0
Input Queue : 0 Output Queue : 0
i/p Messages : 0 o/p Messages : 0
i/p Octets : 0 o/p Octets : 0
i/p Updates : 0 o/p Updates : 0
Export Policy : direct2bgp
===============================================================================
*A:ALA-12#
*A:ALA-12# show router 3 bgp neighbor detail
===============================================================================
BGP Neighbor (detail)
===============================================================================
-------------------------------------------------------------------------------
Peer : 10.0.0.15 Group : To_AS_40000
-------------------------------------------------------------------------------
Peer AS : 65205
Peer Address : 10.0.0.15 Peer Port : 0
Local AS : 65206
Local Address : 10.0.0.16 Local Port : 0
Peer Type : External
State : Active Last State : Connect
Last Event : openFail
Last Error : Hold Timer Expire
Connect Retry : 20 Local Pref. : 100
Min Route Advt. : 30 Min AS Orig. : 15
Multipath : 1 Multihop : 5
Damping : Disabled Loop Detect : Ignore
MED Out : No MED Out Authentication : None
Next Hop Self : Disabled AggregatorID Zero: Disabled
Remove Private : Disabled Passive : Disabled
Prefix Limit : No Limit
Hold Time : 90 Keep Alive : 30
Active Hold Time : 0 Active Keep Alive: 0
Cluster Id : None Client Reflect : Enabled
Preference : 170 Num of Flaps : 0
Recd. Prefixes : 0 Active Prefixes : 0
Recd. Paths : 0 Suppressed Paths : 0
Input Queue : 0 Output Queue : 0
i/p Messages : 0 o/p Messages : 0
i/p Octets : 0 o/p Octets : 0
i/p Updates : 0 o/p Updates : 0
Export Policy : direct2bgp
===============================================================================
*A:ALA-12#| Label | Description |
|---|---|
|
Peer |
The IP address of the configured BGP peer. |
|
Group |
The BGP peer group to which this peer is assigned. |
|
Peer AS |
The configured or inherited peer AS for the peer group. |
|
Peer Address |
The configured address for the BGP peer. |
|
Peer Port |
The TCP port number used on the far-end system. |
|
Local AS |
The configured or inherited local AS for the peer group. |
|
Local Address |
The configured or inherited local address for originating peering for the peer group. |
|
Local Port |
The TCP port number used on the local system. |
|
Peer Type |
External Peer type configured as external BGP peers. |
|
Internal Peer type configured as internal BGP peers. |
|
|
State |
Idle The BGP peer is not accepting connections. |
|
Active BGP is listening for and accepting TCP connections from this peer. |
|
|
Connect BGP is attempting to establish a TCP connection from this peer. |
|
|
Open Sent BGP has sent an OPEN message to the peer and is waiting for an OPEN message from the peer. |
|
|
Open Confirm BGP has received a valid OPEN message from the peer and is awaiting a KEEPALIVE or NOTIFICATION. |
|
|
Established BGP has successfully established a peering and is exchanging routing information. |
|
|
Last State |
Idle The BGP peer is not accepting connections. |
|
Active BGP is listening for and accepting TCP connections from this peer. |
|
|
Connect BGP is attempting to establish a TCP connection with this peer. |
|
|
Connect BGP is attempting to establish a TCP connections from this peer. |
|
|
Open Sent BGP has sent an OPEN message to the peer and is waiting for an OPEN message from the peer. |
|
|
Open Confirm BGP has received a valid OPEN message from the peer and is awaiting a KEEPALIVE or NOTIFICATION. |
|
|
Open Confirm BGP has received a valid OPEN message from the peer and is awaiting a KEEPALIVE or NOTIFICATION. |
|
|
Last Event |
start BGP has initialized the BGP neighbor. |
|
stop BGP has disabled the BGP neighbor. |
|
|
open BGP transport connection opened. |
|
|
close BGP transport connection closed. |
|
|
openFail BGP transport connection failed to open. |
|
|
error BGP transport connection error. |
|
|
connectRetry Connect retry timer expired. |
|
|
holdTime Hold time timer expired. |
|
|
keepAlive Keepalive timer expired. |
|
|
recvOpen Receive an OPEN message. |
|
|
revKeepalive Receive an KEEPALIVE message. |
|
|
recvUpdate Receive an UPDATE message. |
|
|
recvNotify Receive an NOTIFICATION message. |
|
|
None No events have occurred. |
|
|
Last Error |
Displays the last BGP error and sub-code to occur on the BGP neighbor. |
|
Connect Retry |
The configured or inherited connect retry timer value. |
|
Local Pref. |
The configured or inherited local preference value. |
|
Min Route Advt. |
The minimum amount of time that must pass between route updates for the same IP prefix. |
|
Min AS Originate |
The minimum amount of time that must pass between updates for a route originated by the local router. |
|
Multihop |
The maximum number of router hops a BGP connection can traverse. |
|
Multipath |
The configured or inherited multipath value, determining the maximum number of ECMP routes BGP can advertise to the RTM. |
|
Damping |
Disabled BGP neighbor is configured not to dampen route flaps. |
|
Enabled BGP neighbor is configured to dampen route flaps. |
|
|
Loop Detect |
Ignore The BGP neighbor is configured to ignore routes with an AS loop. |
|
Drop The BGP neighbor is configured to drop the BGP peering if an AS loop is detected. |
|
|
Off AS loop detection is disabled for the neighbor. |
|
|
MED Out |
The configured or inherited MED value assigned to advertised routes without a MED attribute. |
|
Authentication |
None No authentication is configured. |
|
MD5 MD5 authentication is configured. |
|
|
Next Hop Self |
Disabled BGP is not configured to send only its own IP address as the BGP next hop in route updates to the specified neighbor. |
|
Enabled BGP sends only its own IP address as the BGP next-hop in route updates to the neighbor. |
|
|
AggregatorID Zero |
Disabled The BGP Neighbor is not configured to set the aggregator ID to 0.0.0.0 in all originated route aggregates. |
|
Enabled The BGP Neighbor is configured to set the aggregator ID to 0.0.0.0 in all originated route aggregates. |
|
|
Remove Private |
Disabled BGP does not remove all private AS numbers from the AS path attribute, in updates sent to the specified neighbor. |
|
Enabled BGP removes all private AS numbers from the AS path attribute, in updates sent to the specified neighbor. |
|
|
Passive |
Disabled BGP actively attempts to establish a BGP connection with the specified neighbor. |
|
Enabled BGP does not actively attempt to establish a BGP connection with the specified neighbor. |
|
|
Prefix Limit |
No Limit No route limit assigned to the BGP peer group. |
|
1 to 4294967295 The maximum number of routes BGP can learn from a peer. |
|
|
Hold Time |
The configured hold time setting. |
|
Keep Alive |
The configured keepalive setting. |
|
Active Hold Time |
The negotiated hold time, if the BGP neighbor is in an established state. |
|
Active Keep Alive |
The negotiated keepalive time, if the BGP neighbor is in an established state. |
|
Cluster Id |
The configured route reflector cluster ID. None No cluster ID has been configured |
|
Client Reflect |
Disabled The BGP route reflector is configured not to reflect routes to this neighbor. |
|
Enabled The BGP route reflector is configured to reflect routes to this neighbor. |
|
|
Preference |
The configured route preference value for the peer group. |
|
Num of Flaps |
The number of flaps in the neighbor connection. |
|
Recd. Prefixes |
The number of routes received from the BGP neighbor. |
|
Active Prefixes |
The number of routes received from the BGP neighbor and active in the forwarding table. |
|
Recd. Paths |
The number of unique sets of path attributes received from the BGP neighbor. |
|
Suppressed Paths |
The number of unique sets of path attributes received from the BGP neighbor and suppressed because of route damping. |
|
Input Queue |
The number of BGP messages to be processed. |
|
Output Queue |
The number of BGP messages to be transmitted. |
|
i/p Messages |
Total number of packets received from the BGP neighbor. |
|
o/p Messages |
Total number of packets sent to the BGP neighbor. |
|
i/p Octets |
Total number of octets received from the BGP neighbor. |
|
o/p Octets |
Total number of octets sent to the BGP neighbor. |
|
i/p Updates |
Total number of BGP updates received from the BGP neighbor. |
|
o/p Updates |
Total number of BGP updates sent to the BGP neighbor. |
|
Export Policy |
The configured export policies for the peer group. |
|
Import Policy |
The configured import policies for the peer group. |
*A:ALA-12# show router 3 bgp neighbor 10.0.0.16 received-routes
==============================================================================
BGP Router ID : 10.0.0.16 AS : 65206 Local AS : 65206
===============================================================================
Legend -
Status codes : u - used, s - suppressed, h - history, d - decayed, * - valid
Origin codes : i - IGP, e - EGP, ? - incomplete, > - best
===============================================================================
BGP Neighbor
===============================================================================
Flag Network Nexthop LocalPref MED As-Path
-------------------------------------------------------------------------------
? 10.0.0.16/32 10.0.0.16 100 none No As-Path
? 10.0.6.0/24 10.0.0.16 100 none No As-Path
? 10.0.8.0/24 10.0.0.16 100 none No As-Path
? 10.0.12.0/24 10.0.0.16 100 none No As-Path
? 10.0.13.0/24 10.0.0.16 100 none No As-Path
? 10.0.204.0/24 10.0.0.16 100 none No As-Path
===============================================================================
*A:ALA-12#
| Label | Description |
|---|---|
|
BGP Router ID |
The local BGP router ID. |
|
AS |
The configured AS number. |
|
Local AS |
The configured local AS setting. If not configured, it is the same value as the AS. |
|
Flag |
u used |
|
s suppressed |
|
|
h history |
|
|
d decayed |
|
|
* valid |
|
|
i igp |
|
|
? incomplete |
|
|
> best |
|
|
Network |
Route IP prefix and mask length for the route. |
|
Next Hop |
BGP next hop for the route. |
|
LocalPref |
BGP local preference path attribute for the route. |
|
MED |
BGP Multi-Exit Discriminator (MED) path attribute for the route. |
|
AS Path |
The BGP AS path for the route. |
*A:7210SAS>show>service>id# show service id 1 base
===============================================================================
Service Basic Information
===============================================================================
Service Id : 1 Vpn Id : 0
Service Type : VPRN
Name : (Not Specified)
Description : Default Description For VPRN ID 1
Customer Id : 1
Last Status Change: 01/08/2000 22:57:35
Last Mgmt Change : 01/08/2000 22:57:35
Admin State : Up Oper State : Up
Route Dist. : 100:1 VPRN Type : regular
AS Number : 100 Router Id : 1.1.1.1
ECMP : Enabled ECMP Max Routes : 1
Max IPv4 Routes : No Limit Auto Bind : MPLS
Max IPv6 Routes : No Limit
Ignore NH Metric : Disabled
Hash Label : Disabled
Vrf Target : target:200:1
Vrf Import : None
Vrf Export : None
MVPN Vrf Target : None
MVPN Vrf Import : None
MVPN Vrf Export : None
Label mode : vrf
BGP VPN Backup : ipv4 ipv6
SAP Count : 1 SDP Bind Count : 3
-------------------------------------------------------------------------------
Service Access & Destination Points
-------------------------------------------------------------------------------
Identifier Type AdmMTU OprMTU Adm Opr
-------------------------------------------------------------------------------
sap:1/1/2:1 q-tag 9212 9212 Up Up
sdp:1002:1 S(2.2.2.2) Spok 0 9186 Up Up
sdp:1003:1 S(3.3.3.3) Spok 0 9186 Up Up
sdp:1004:1 S(4.4.4.4) Spok 0 9186 Up Up
===============================================================================
*A:7210SAS>show>service>id# *A:7210SAS# show router bgp neighbor 2.2.2.2
===============================================================================
BGP Neighbor
===============================================================================
-------------------------------------------------------------------------------
Peer : 2.2.2.2
Group : toPE
-------------------------------------------------------------------------------
Peer AS : 100 Peer Port : 50854
Peer Address : 10.2.2.2
Local AS : 100 Local Port : 179
Local Address : 10.1.1.1
Peer Type : Internal
State : Established Last State : Established
Last Event : recvKeepAlive
Last Error : Cease (Connection Collision Resolution)
Local Family : IPv4 VPN-IPv4 IPv6 VPN-IPv6
Remote Family : IPv4 VPN-IPv4 IPv6 VPN-IPv6
Hold Time : 90 Keep Alive : 30
Min Hold Time : 0
Active Hold Time : 90 Active Keep Alive : 30
Cluster Id : None
Preference : 170 Num of Update Flaps : 0
Recd. Paths : 0
IPv4 Recd. Prefixes : 0 IPv4 Active Prefixes : 0
IPv4 Suppressed Pfxs : 0 VPN-IPv4 Suppr. Pfxs : 0
VPN-IPv4 Recd. Pfxs : 0 VPN-IPv4 Active Pfxs : 0
Mc IPv4 Recd. Pfxs. : 0 Mc IPv4 Active Pfxs. : 0
Mc IPv4 Suppr. Pfxs : 0 IPv6 Suppressed Pfxs : 0
IPv6 Recd. Prefixes : 0 IPv6 Active Prefixes : 0
VPN-IPv6 Recd. Pfxs : 0 VPN-IPv6 Active Pfxs : 0
VPN-IPv6 Suppr. Pfxs : 0 L2-VPN Suppr. Pfxs : 0
L2-VPN Recd. Pfxs : 0 L2-VPN Active Pfxs : 0
MVPN-IPv4 Suppr. Pfxs: 0 MVPN-IPv4 Recd. Pfxs : 0
MVPN-IPv4 Active Pfxs: 0 MDT-SAFI Suppr. Pfxs : 0
MDT-SAFI Recd. Pfxs : 0 MDT-SAFI Active Pfxs : 0
FLOW-IPV4-SAFI Suppr*: 0 FLOW-IPV4-SAFI Recd.*: 0
FLOW-IPV4-SAFI Activ*: 0 Rte-Tgt Suppr. Pfxs : 0
Rte-Tgt Recd. Pfxs : 0 Rte-Tgt Active Pfxs : 0
Backup IPv4 Pfxs : 0 Backup IPv6 Pfxs : 0
Mc Vpn Ipv4 Recd. Pf*: 0 Mc Vpn Ipv4 Active P*: 0
Backup Vpn IPv4 Pfxs : 0 Backup Vpn IPv6 Pfxs : 0
Input Queue : 0 Output Queue : 0
i/p Messages : 9042 o/p Messages : 65
i/p Octets : 111 o/p Octets : 278
i/p Updates : 0 o/p Updates : 0
TTL Security : Disabled Min TTL Value : n/a
Graceful Restart : Disabled Stale Routes Time : n/a
Advertise Inactive : Disabled Peer Tracking : Disabled
Advertise Label : ipv4 ipv6
Auth key chain : n/a
Disable Cap Nego : Disabled Bfd Enabled : Enabled
Flowspec Validate : Disabled Default Route Tgt : Disabled
L2 VPN Cisco Interop : Disabled
Local Capability : RtRefresh MPBGP 4byte ASN
Remote Capability : RtRefresh MPBGP 4byte ASN
Local AddPath Capabi*: Send - VPN-IPv4 (1) VPN-IPv6 (4)
: Receive - VPN-IPv6
Remote AddPath Capab*: Send - VPN-IPv6
: Receive - VPN-IPv4 VPN-IPv6
Import Policy : None Specified / Inherited
Export Policy : P1
-------------------------------------------------------------------------------
Neighbors : 1
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:7210SAS# paths
show>router>bgp
Supported on all 7210 SAS platforms as described in this document
This command displays a summary of BGP path attributes.
The following output is an example of BGP path information, and Table: Output fields: BGP paths describes the output fields.
Sample output*A:ALA-12# show router 3 bgp paths
==============================================================================
BGP Router ID : 10.0.0.14 AS : 65206 Local AS : 65206
==============================================================================
BGP Paths
------------------------------------------------------------------------------
Path: 60203 65001 19855 3356 15412
------------------------------------------------------------------------------
Origin : IGP Next Hop : 10.0.28.1
MED : 60203 Local Preference : none
Refs : 4 ASes : 5
Segments : 1
Flags : EBGP-learned
Aggregator : 15412 62.216.140.1
------------------------------------------------------------------------------
Path: 60203 65001 19855 3356 1 1236 1236 1236 1236
------------------------------------------------------------------------------
Origin : IGP Next Hop : 10.0.28.1
MED : 60203 Local Preference : none
Refs : 2 ASes : 9
Segments : 1
Flags : EBGP-learned
------------------------------------------------------------------------------
*A:ALA-12# | Label | Description |
|---|---|
|
BGP Router ID |
The local BGP router ID. |
|
AS |
The configured autonomous system number. |
|
Local AS |
The configured local AS setting. If not configured, the value is the same as the AS. |
|
Path |
The AS path attribute. |
|
Origin |
EGP The NLRI is learned by an EGP protocol. |
|
IGP The NLRI is interior to the originating AS. |
|
|
INCOMPLETE NLRI was learned another way. |
|
|
Next Hop |
The advertised BGP next hop. |
|
MED |
The Multi-Exit Discriminator value. |
|
Local Preference |
The local preference value. |
|
Refs |
The number of routes using a specified set of path attributes. |
|
ASes |
The number of autonomous system numbers in the AS path attribute. |
|
Segments |
The number of segments in the AS path attribute. |
|
Flags |
eBGP-learned Path attributes learned by an eBGP peering. |
|
iBGP-Learned Path attributes learned by an iBGP peering. |
|
|
Aggregator |
The route aggregator ID. |
|
Community |
The BGP community attribute list. |
|
Originator ID |
The originator ID path attribute value. |
|
Cluster List |
The route reflector cluster list. |
routes [family family] [prefix [detail | longer]]
routes [family family] [prefix [hunt | brief]]
routes [family family] [community comm-id]
routes [family family] [aspath-regex reg-ex1]
routes [family family] [ipv6-prefix[/prefix-length] [detail | longer] | [hunt [brief]]]
show>router>bgp
Supported on all 7210 SAS platforms as described in this document
This command displays BGP route information.
When this command is issued without any parameters, the entire BGP routing table displays.
When this command is issued with an IP prefix/mask or IP address, the best match for the parameter displays.
Specifies the type of routing information to be distributed by the BGP instance.
Specifies the type of routing information to display.
Specifies route criteria.
Displays all routes with an AS path matching the specified regular expression reg-exp.
Displays all routes with the specified BGP community.
The following outputs are examples of BGP route information, and Table: Output fields: BGP routes describes the output fields.
Sample output*A:ALA-12>config>router>bgp# show router 3 bgp routes family ipv4
==============================================================================
BGP Router ID : 10.10.10.103 AS : 200 Local AS : 200
==============================================================================
Legend -
Status codes : u - used, s - suppressed, h - history, d - decayed, * - valid
Origin codes : i - IGP, e - EGP, ? - incomplete, > - best
==============================================================================
BGP Routes
==============================================================================
Flag Network Nexthop LocalPref MED
VPN Label As-Path
------------------------------------------------------------------------------
No Matching Entries Found
==============================================================================
*A:ALA-12>config>router>bgp#
A:SR-12# show router bgp routes 10.0.0.0/31 hunt
===============================================================================
BGP Router ID : 10.20.1.1 AS : 100Local AS : 100
===============================================================================
Legend -
Status codes : u - used, s - suppressed, h - history, d - decayed, * - valid
Origin codes : i - IGP, e - EGP, ? - incomplete, > - best
===============================================================================
BGP Routes
===============================================================================
RIB In Entries
-------------------------------------------------------------------------------
Network : 10.0.0.0/31
Nexthop : 10.20.1.2
Route Dist. : 10.20.1.2:1VPN Label: 131070
From : 10.20.1.2
Res. Nexthop : 10.10.1.2
Local Pref. : 100Interface Name: to-sr7
Aggregator AS : noneAggregator: none
Atomic Aggr. : Not AtomicMED: none
Community : target:10.20.1.2:1
Cluster : No Cluster Members
Originator Id : NonePeer Router Id: 10.20.1.2
Flags : Used Valid Best IGP
AS-Path : No As-Path
VPRN Imported : 1 2 10 12
-------------------------------------------------------------------------------
RIB Out Entries
-------------------------------------------------------------------------------
Routes : 1
===============================================================================
A:SR-12# | Label | Description |
|---|---|
|
BGP Router ID |
The local BGP router ID. |
|
AS |
The configured AS number. |
|
Local AS |
The configured local AS setting; if not configured, it is the same as the system AS. |
|
Network |
The IP prefix and mask length. |
|
Nexthop |
The BGP next hop. |
|
From |
The advertising BGP neighbor IP address. |
|
Res. Nexthop |
The resolved next hop. |
|
Local Pref. |
The local preference value. |
|
Flag |
u used |
|
s suppressed |
|
|
h history |
|
|
d decayed |
|
|
* valid |
|
|
i igp |
|
|
e egp |
|
|
? incomplete |
|
|
> best |
|
|
Aggregator AS |
The aggregator AS value. none No aggregator AS attributes are present. |
|
Aggregator |
The aggregator attribute value. none no Aggregator attributes are present. |
|
Atomic Aggr. |
Atomic The atomic aggregator flag is set. |
|
Not Atomic The atomic aggregator flag is not set. |
|
|
MED |
The MED metric value. none No MED metric is present. |
|
Community |
The BGP community attribute list. |
|
Cluster |
The route reflector cluster list. |
|
Originator Id |
The originator ID path attribute value. |
|
none The originator ID attribute is not present. |
|
|
Peer Router Id |
The router ID of the advertising router. |
|
AS-Path |
The BGP AS path attribute. |
|
VPRN Imported |
Displays the VPRNs where a particular BGP-VPN received route has been imported and installed. |
summary [all]
show>router>bgp
Supported on all 7210 SAS platforms as described in this document
This command displays a summary of BGP neighbor information.
If confederations are not configured, that portion of the output does not display.
The ‟State” field displays the global BGP operational state. The valid values are:
Up
BGP global process is configured and running.
Down
BGP global process is administratively shutdown and not running.
Disabled
BGP global process is operationally disabled. The process must be restarted by the operator.
For example, if a BGP peer is operationally disabled, the state in the summary table displays the state ‟Disabled”.
Displays BGP peers in all instances.
The following output is an example of summary BGP information, and Table: Output fields: BGP summary describes the output fields.
Sample output*A:ALA-12# show router 3 bgp summary
===============================================================================
BGP Router ID : 10.0.0.14 AS : 65206 Local AS : 65206
===============================================================================
BGP Admin State : Up BGP Oper State : Up
Confederation AS : 40000
Member Confederations : 65205 65206 65207 65208
Number of Peer Groups : 2 Number of Peers : 7
Total BGP Active Routes : 86689 Total BGP Routes : 116999
Total BGP Paths : 35860 Total Path Memory : 2749476
Total Supressed Routes : 0 Total History Routes : 0
Total Decayed Routes : 0
===============================================================================
BGP Summary
===============================================================================
Neighbor AS PktRcvd PktSent InQ OutQ Up/Down State|Recv/Actv/Sent
-------------------------------------------------------------------------------
10.0.0.1 65206 5 21849 0 0 00h01m29s 32/0/86683
10.0.0.12 65206 0 0 0 0 00h01m29s Active
10.0.0.13 65206 5 10545 0 50 00h01m29s 6/0/86683
10.0.0.15 65205 0 0 0 0 00h01m29s Active
10.0.0.16 65206 5 9636 0 50 00h01m29s 6/0/86683
10.0.27.1 2 0 0 0 0 00h01m29s Active
10.0.28.1 60203 22512 15 0 0 00h01m29s 116955/86689/9
===============================================================================
*A:ALA-12#
| Label | Description |
|---|---|
|
BGP Router ID |
The local BGP router ID. |
|
AS |
The configured autonomous system number. |
|
Local AS |
The configured local AS setting, if not configured it is the same as the system AS. |
|
BGP Admin State |
Down BGP is administratively disabled. |
|
Up BGP is administratively enabled. |
|
|
BGP Oper State |
Down BGP is operationally disabled. |
|
Up BGP is operationally enabled. |
|
|
Confederation AS |
The configured confederation AS. |
|
Member Confederations |
The configured members of the BGP confederation. |
|
Number of Peer Groups |
The total number of configured BGP peer groups. |
|
Number of Peers |
The total number of configured BGP peers. |
|
Total BGP Active Routes |
The total number of BGP routes used in the forwarding table. |
|
Total BGP Routes |
The total number of BGP routes learned from BGP peers. |
|
Total BGP Paths |
The total number of unique sets of BGP path attributes learned from BGP peers. |
|
Total Path Memory |
Total amount of memory used to store the path attributes. |
|
Total Suppressed Routes |
Total number of suppressed routes because of route damping. |
|
Total History Routes |
Total number of routes with history because of route damping. |
|
Total Decayed Routes |
Total number of decayed routes because of route damping. |
|
Neighbor |
BGP neighbor address. |
|
AS (Neighbor) |
BGP neighbor AS number. |
|
PktRcvd |
Total number of packets received from the BGP neighbor. |
|
PktSent |
Total number of packets sent to the BGP neighbor. |
|
InQ |
The number of BGP messages to be processed. |
|
OutQ |
The number of BGP messages to be transmitted. |
|
Up/Down |
The amount of time that the BGP neighbor has either been established or not established depending on its current state. |
|
State|Recv/Actv/Sent |
The BGP neighbor current state (if not established) or the number of received routes, active routes and sent routes (if established). |
interface [{[ip-address | ip-int-name] [detail]} | summary]
show>router
Supported on all 7210 SAS platforms as described in this document
This command displays the router IP interface table sorted by interface index.
Displays only the interface information associated with the specified IP address.
Displays only the interface information associated with the specified IP interface name.
Displays detailed IP interface information.
Displays summary IP interface information for the router.
The following outputs are examples of router interface information, and the associated tables describe the output fields.
Sample output — detailed, Table: Output fields: IP interface
Sample output — standard, Table: Output fields: IP interface standard
Sample output — summary, Table: Output fields: router IP interface summary
*A:ALA-12# show router 3 interface detail
==============================================================================
Interface Table
==============================================================================
Interface
------------------------------------------------------------------------------
If Name : to-ser1
Admin State : Up Oper State : Up
IP Addr/mask : 10.10.13.3/24 Address Type : Primary
IGP Inhibit : Disabled Broadcast Address: Host-ones
IP Addr/mask : 10.200.0.1/16 Address Type : Secondary
IGP Inhibit : Enabled Broadcast Address: Host-ones
------------------------------------------------------------------------------
Details
------------------------------------------------------------------------------
If Index : 2
Port Id : 1/1/2 If Type : Network
Egress Filter: none Ingress Filter : 100
QoS Policy : 1 SNTP Broadcast : False
MAC Address : 04:5d:01:01:00:02 Arp Timeout : 14400
ICMP Details
Redirects : Disabled
Unreachables : Number - 100 Time (seconds) - 10
TTL Expired : Number - 100 Time (seconds) - 10
==============================================================================
*A:ALA-12# | Label | Description |
|---|---|
|
If Name |
The IP interface name. |
|
Admin State |
Down — The IP interface is administratively disabled. Up — The IP interface is administratively enabled. |
|
Oper State |
Down — The IP interface is operationally disabled. Up — The IP interface is operationally disabled. |
|
IP Addr/mask |
The IP address and subnet mask length of the IP interface. Not Assigned — Indicates no IP address has been assigned to the IP interface. |
|
Address Type |
Primary — The IP address for the IP interface is the Primary address on the IP interface. Secondary — The IP address for the IP interface is a Secondary address on the IP interface. |
|
IGP Inhibit |
Disabled — The secondary IP address on the interface is recognized as a local interface by the IGP. Enabled — The secondary IP address on the interface is not recognized as a local interface by the IGP. |
|
Broadcast Address |
All-ones — The broadcast format on the IP interface is all ones. Host-ones — The broadcast format on the IP interface is host ones. |
|
If Index |
The interface index of the IP router interface. |
|
If Type |
Network — The IP interface is a network/core IP interface. Service — The IP interface is a service IP interface. |
|
Port Id |
The port ID of the IP interface. |
|
Egress Filter |
The egress IP filter policy ID associated with the IP interface. none — Indicates no egress filter policy is associated with the interface. |
|
Ingress Filter |
The ingress IP filter policy ID associated with the IP interface. none — Indicates no ingress filter policy is associated with the interface. |
|
QoS Policy |
The QoS policy ID associated with the IP interface. |
|
SNTP Broadcast |
False — Receipt of SNTP broadcasts on the IP interface is disabled. True — Receipt of SNTP broadcasts on the IP interface is enabled. |
|
MAC Address |
The MAC address of the IP interface. |
|
Arp Timeout |
The ARP timeout for the interface, in seconds, which is the time an ARP entry is maintained in the ARP cache without being refreshed. |
|
ICMP Mask Reply |
False — The IP interface does not reply to a received ICMP mask request. True — The IP interface replies to a received ICMP mask request. |
|
Redirects |
Specifies the maximum number of ICMP redirect messages the IP interface issues in a specific period of time (Time (seconds)). Disabled — Indicates the IP interface does not generate ICMP redirect messages. |
|
Unreachables |
Specifies the maximum number of ICMP destination unreachable messages the IP interface issues in a specific period of time. Disabled — Indicates the IP interface does not generate ICMP destination unreachable messages. |
|
TTL Expired |
The maximum number (Number) of ICMP TTL expired messages the IP interface issues in a specific period of time (Time (seconds)). Disabled — Indicates the IP interface does not generate ICMP TTL expired messages. |
*A:7210SAS>show>router interface i1 detail
===============================================================================
Interface Table (Router: Base)
===============================================================================
-------------------------------------------------------------------------------
Interface
-------------------------------------------------------------------------------
If Name : i1
Admin State : Up Oper (v4/v6) : Down/--
Protocols : None
IP Addr/mask : Not Assigned
-------------------------------------------------------------------------------
Details
-------------------------------------------------------------------------------
Description : (Not Specified)
If Index : 2 Virt. If Index : 2
Last Oper Chg: 03/07/2001 01:47:29 Global If Index : 127
Port Id : 1/1/1
TOS Marking : Trusted If Type : Network
Egress Filter: none Ingress Filter : none
Egr IPv6 Flt : none Ingr IPv6 Flt : none
SNTP B.Cast : False QoS Policy : 2
Queue-group : None
MAC Address : 00:25:ba:0d:27:32 Arp Timeout : 14400
IP Oper MTU : 9198
LdpSyncTimer : None Strip-Label : Disabled
uRPF Chk : disabled
uRPF Fail By*: 0 uRPF Chk Fail Pk*: 0
ICMP Details
Redirects : Number - 100 Time (seconds) - 10
Unreachables : Number - 100 Time (seconds) - 10
TTL Expired : Number - 100 Time (seconds) - 10
===============================================================================
Meter Statistics
===============================================================================
-------------------------------------------------------------------------------
Packets Octets
-------------------------------------------------------------------------------
Ingress Meter 1 (Unicast)
For. InProf : 0 0
For. OutProf : 0 0
Ingress Meter 9 (Multipoint)
For. InProf : 0 0
For. OutProf : 0 0
===============================================================================
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:7210SAS>show>router#| Label | Description |
|---|---|
|
Interface-Name |
The IP interface name. |
|
Type |
n/a — No IP address has been assigned to the IP interface, so the IP address type is not applicable. Pri — The IP address for the IP interface is the Primary address on the IP interface. Sec — The IP address for the IP interface is a secondary address on the IP interface. |
|
IP-Address |
The IP address and subnet mask length of the IP interface. n/a — Indicates no IP address has been assigned to the IP interface. |
|
Adm |
Down — The IP interface is administratively disabled. Up — The IP interface is administratively enabled. |
|
Opr |
Down — The IP interface is operationally disabled. Up — The IP interface is operationally enabled. |
|
Mode |
Network — The IP interface is a network/core IP interface. Service — The IP interface is a service IP interface. |
*A:ALA-12# show router 3 interface summary
===============================================================================
Router Summary (Interfaces)
===============================================================================
Instance Router Name Interfaces Admin-Up Oper-Up
-------------------------------------------------------------------------------
1 Base 7 7 5
===============================================================================
*A:ALA-12# | Label | Description |
|---|---|
|
Instance |
The router instance number. |
|
Router Name |
The name of the router instance. |
|
Interfaces |
The number of IP interfaces in the router instance. |
mvpn
show>router
Supported on all 7210 SAS platforms as described in this document
This command displays multicast VPN related information. The router instance must be specified.
The following output is an example of MVPN information, and Table: Output fields: MVPN describes the output fields.
Sample output*A:Dut-y# show router 10 mvpn
===============================================================================
MVPN 10 configuration data
===============================================================================
signaling : Bgp auto-discovery : Default
UMH Selection : Highest-Ip intersite-shared : Enabled
vrf-import : N/A
vrf-export : N/A
vrf-target : unicast
C-Mcast Import RT : target:16.16.16.16:3
ipmsi : ldp
i-pmsi P2MP AdmSt : Up
spmsi : ldp
s-pmsi P2MP AdmSt : Up
max-p2mp-spmsi : 251
data-delay-interval: 3 seconds
enable-asm-mdt : N/A
data-threshold : 224.0.0.0/4 --> 1 kbps
===============================================================================
*A:Dut-y# | Label | Description |
|---|---|
|
signaling |
Displays the signaling type. |
|
UMH Selection |
Displays the UMH selection method. |
|
vrf-import |
Displays the VRF import policy in use. |
|
vrf-export |
Displays the VRF export policy in use. |
|
vrf-target |
Displays the VRF target. |
|
C-Mcast Import RT |
Displays the c-multicast import router PE system address or loopback address. This address is common for all VPNs on the PE. |
|
ipmsi |
Displays the signaling protocol used to setup the I-PMSI tree transport tunnel. |
|
i-pmsi P2MP AdmSt |
Displays I-PMSI P2MP administrative state. |
|
spmsi |
Displays signaling protocol used to setup the S-PMSI tree transport tunnel. |
|
s-pmsi P2MP AdmSt |
Displays the S-PMSI P2MP administrative state. |
|
max-p2mp-spmsi |
Displays the maximum number of P2MP S-PMSIs. |
|
data-delay-interval |
Displays the interval, in seconds, before a PE router connected to the source switches traffic from the inclusive provider tunnel to the selective provider tunnel. |
|
enable-asm-mdt |
Displays whether ASM MDT is enabled. |
|
data-threshold |
Displays the data threshold. |
mvpn-list [type type] [auto-discovery auto-discovery] [signalling signalling] [group group]
show>router
Supported on all 7210 SAS platforms as described in this document
This command displays multicast VPN list-related information. The router instance must be specified.
Specifies the MVPN type.
Specifies the auto-discovery mode.
Specifies the signaling type.
Specifies the group address.
The following output is an example of multicast VPN list information, and Table: Output fields: MVPN list describes the output fields.
Sample output*A:Dut-y# show router mvpn-list
===============================================================================
MVPN List
===============================================================================
VprnID Sig A-D iPmsi/sPmsi GroupAddr/Lsp-Template (S,G)/(*,G)
-------------------------------------------------------------------------------
10 Bgp Default Mldp/Mldp N/A 512/0
20 Bgp Default Mldp/Mldp N/A 512/0
30 Bgp Default None/None N/A 0/0
-------------------------------------------------------------------------------
Total PIM I-PMSI tunnels : 0
Total RSVP I-PMSI tunnels : 0
Total MLDP I-PMSI tunnels : 2
Total PIM TX S-PMSI tunnels : 0
Total RSVP TX S-PMSI tunnels : 0
Total MLDP TX S-PMSI tunnels : 502
Total PIM RX S-PMSI tunnels : 0
Total RSVP RX S-PMSI tunnels : 0
Total MLDP RX S-PMSI tunnels : 0
Total (S,G) : 1024
Total (*,G) : 0
Total Mvpns : 3
Sig = Signal Pim-a = pim-asm Pim-s = pim-ssm A-D = Auto-Discovery
===============================================================================
*A:Dut-y# | Label | Description |
|---|---|
|
Total PIM I-PMSI tunnels |
Displays the total number of PIM I-PMSI tunnels. |
|
Total RSVP I-PMSI tunnels |
Displays the total number of RSVP I-PMSI tunnels. |
|
Total MLDP I-PMSI tunnels |
Displays the total number of MLDP I-PMSI tunnels. |
|
Total PIM TX I-PMSI tunnels |
Displays the total number of PIM I-PMSI transmit tunnels. |
|
Total RSVP TX I-PMSI tunnels |
Displays the total number of RSVP I-PMSI transmit tunnels. |
|
Total MLDP TX I-PMSI tunnels |
Displays the total number of MLDP I-PMSI transmit tunnels. |
|
Total PIM RX I-PMSI tunnels |
Displays the total number of PIM I-PMSI receive tunnels. |
|
Total RSVP RX I-PMSI tunnels |
Displays the total number of RSVP I-PMSI receive tunnels. |
|
Total MLDP RX I-PMSI tunnels |
Displays the total number of MLDP I-PMSI receive tunnels. |
|
Total (S,G) |
Displays the total number of (S,G) multicast groups. |
|
Total (*,G) |
Displays the total number of (*,G) multicast groups. |
|
Total Mvpns |
Displays the total number of MVPNs. |
route-table [ip-prefix [/mask] [longer] | [protocol protocol] | [summary]]
show>router
Supported on all 7210 SAS platforms as described in this document
This command displays the active routes in the routing table.
If no command line arguments are specified, all routes are displayed, sorted by prefix.
Displays routes only matching the specified ip-prefix and optional mask.
Displays routes matching the ip-prefix/mask and routes with longer masks.
Displays routes learned from the specified protocol.
Displays route table summary information.
The following output is an example of route table information, and Table: Output fields: route table describes the output fields.
Sample output*A:ALA-12# show router 3 route-table
==============================================================================
Route Table
==============================================================================
Dest Address Next Hop Type Protocol Age Metric Pref
------------------------------------------------------------------------------
10.10.0.1/32 10.10.13.1 Remote OSPF 65844 1001 10
10.10.0.2/32 10.10.13.1 Remote OSPF 65844 2001 10
10.10.0.3/32 0.0.0.0 Local Local 1329261 0 0
10.10.0.4/32 10.10.34.4 Remote OSPF 3523 1001 10
10.10.0.5/32 10.10.35.5 Remote OSPF 1084022 1001 10
10.10.12.0/24 10.10.13.1 Remote OSPF 65844 2000 10
10.10.13.0/24 0.0.0.0 Local Local 65859 0 0
10.10.15.0/24 10.10.13.1 Remote OSPF 58836 2000 10
10.10.24.0/24 10.10.34.4 Remote OSPF 3523 2000 10
10.10.25.0/24 10.10.35.5 Remote OSPF 399059 2000 10
10.10.34.0/24 0.0.0.0 Local Local 3543 0 0
10.10.35.0/24 0.0.0.0 Local Local 1329259 0 0
10.10.45.0/24 10.10.34.4 Remote OSPF 3523 2000 10
10.200.0.0/16 0.0.0.0 Local Local 4513 0 0
192.168.0.0/20 0.0.0.0 Local Local 1329264 0 0
192.168.254.0/24 0.0.0.0 Remote Static 11 1 5
------------------------------------------------------------------------------
*A:ALA-12#
*A:ALA-12# show router 3 route-table 10.10.0.4
===============================================================================
Route Table
==============================================================================
Dest Address Next Hop Type Protocol Age Metric Pref
------------------------------------------------------------------------------
10.10.0.4/32 10.10.34.4 Remote OSPF 3523 1001 10
------------------------------------------------------------------------------
*A:ALA-12#
*A:ALA-12# show router 3 route-table 10.10.0.4/32 longer
==============================================================================
Route Table
==============================================================================
Dest Address Next Hop Type Protocol Age Metric Pref
------------------------------------------------------------------------------
10.10.0.4/32 10.10.34.4 Remote OSPF 3523 1001 10
------------------------------------------------------------------------------
No. of Routes: 1
==============================================================================
+ : indicates that the route matches on a longer prefix
*A:ALA-12#
*A:ALA-12# show router 3 route-table protocol ospf
==============================================================================
Route Table
==============================================================================
Dest Address Next Hop Type Protocol Age Metric Pref
------------------------------------------------------------------------------
10.10.0.1/32 10.10.13.1 Remote OSPF 65844 1001 10
10.10.0.2/32 10.10.13.1 Remote OSPF 65844 2001 10
10.10.0.4/32 10.10.34.4 Remote OSPF 3523 1001 10
10.10.0.5/32 10.10.35.5 Remote OSPF 1084022 1001 10
10.10.12.0/24 10.10.13.1 Remote OSPF 65844 2000 10
10.10.15.0/24 10.10.13.1 Remote OSPF 58836 2000 10
10.10.24.0/24 10.10.34.4 Remote OSPF 3523 2000 10
10.10.25.0/24 10.10.35.5 Remote OSPF 399059 2000 10
10.10.45.0/24 10.10.34.4 Remote OSPF 3523 2000 10
-------------------------------------------------------------------------------
*A:ALA-12#
*A:ALA-12# show router 3 route-table summary
===============================================================================
Route Table Summary
===============================================================================
Active Available
-------------------------------------------------------------------------------
Static 1 1
Direct 6 6
BGP 0 0
OSPF 9 9
ISIS 0 0
RIP 0 0
Aggregate 0 0
-------------------------------------------------------------------------------
Total 15 15
===============================================================================
*A:ALA-12# | Label | Description |
|---|---|
|
Dest Address |
The route destination address and mask. |
|
Next Hop |
The next-hop IP address for the route destination. |
|
Type |
Local — The route is a local route. Remote — The route is a remote route. |
|
Protocol |
The protocol through which the route was learned. |
|
Age |
The age, in seconds, for the route. |
|
Metric |
The metric value for the route. |
|
Pref |
The preference value for the route. |
|
No. of Routes |
The number of routes displayed in the list. |
static-arp [ip-address | ip-int-name | mac ieee-mac-addr]
show>router
Supported on all 7210 SAS platforms as described in this document
This command displays the router static ARP table sorted by IP address.
If no options are present, all ARP entries are displayed.
Displays only static ARP entries associated with the specified IP address.
Displays only static ARP entries associated with the specified IP interface name.
Displays only static ARP entries associated with the specified MAC address.
The following output is an example of static ARP table information, and Table: Output fields: ARP table describes the output fields.
Sample output*A:ALA-12# show router 3 static-arp
==============================================================================
ARP Table
==============================================================================
IP Address MAC Address Age Type Interface
------------------------------------------------------------------------------
10.200.0.253 00:00:5a:40:00:01 00:00:00 Sta to-ser1
10.200.1.1 00:00:5a:01:00:33 00:00:00 Inv to-ser1a
------------------------------------------------------------------------------
No. of ARP Entries: 2
==============================================================================
*A:ALA-12#
*A:ALA-12# show router 3 static-arp 10.200.1.1
==============================================================================
ARP Table
==============================================================================
IP Address MAC Address Age Type Interface
------------------------------------------------------------------------------
10.200.1.1 00:00:5a:01:00:33 00:00:00 Inv to-ser1 a
===============================================================================
*A:ALA-12#
*A:ALA-12# show router 3 static-arp to-ser1
==============================================================================
ARP Table
==============================================================================
IP Address MAC Address Age Type Interface
------------------------------------------------------------------------------
10.200.0.253 00:00:5a:40:00:01 00:00:00 Sta to-ser1
===============================================================================
S*A:ALA-12#
*A:ALA-12# show router 3 static-arp mac 00:00:5a:40:00:01
==============================================================================
ARP Table
==============================================================================
IP Address MAC Address Age Type Interface
-------------------------------------------------------------------------------
10.200.0.253 00:00:5a:40:00:01 00:00:00 Sta to-ser1
==============================================================================
*A:ALA-12# | Label | Description |
|---|---|
|
IP Address |
The IP address of the static ARP entry. |
|
MAC Address |
The MAC address of the static ARP entry. |
|
Age |
The age of the ARP entry. Static ARPs always have 00:00:00 for the age. |
|
Type |
Inv — The ARP entry is an inactive static ARP entry (invalid). Sta — The ARP entry is an active static ARP entry. |
|
Interface |
The IP interface name associated with the ARP entry. |
|
No. of ARP Entries |
The number of ARP entries displayed in the list. |
static-route [ip-prefix /mask] | [preference preference] | [next-hop ip-addr | tag tag] [detail]
show>router
Supported on all 7210 SAS platforms as described in this document
This command displays the static entries in the routing table.
If no options are present, all static routes are displayed sorted by prefix.
Displays only static routes matching the specified ip-prefix and mask.
Displays only static routes with the specified route preference.
Displays only static routes with the specified next hop IP address.
Displays detailed information about the static route.
Displays the tag used to add a 32-bit integer tag to the static route. The tag is used in route policies to control distribution of the route into other protocols.
The following output is an example of static routing table entry information, and Table: Output fields: static route table describes the output fields.
Sample output*A:ALA-12# show router 3 static-route
==============================================================================
Route Table
==============================================================================
IP Addr/mask Pref Metric Type Nexthop Interface Active
------------------------------------------------------------------------------
192.168.250.0/24 5 1 ID 10.200.10.1 to-ser1 Y
192.168.252.0/24 5 1 NH 10.10.0.254 n/a N
192.168.253.0/24 5 1 NH to-ser1 n/a N
192.168.253.0/24 5 1 NH 10.10.0.254 n/a N
192.168.254.0/24 4 1 BH black-hole n/a Y
==============================================================================
*A:ALA-12#
*A:ALA-12# show router 3 static-route 192.168.250.0/24
==============================================================================
Route Table
==============================================================================
IP Addr/mask Pref Metric Type Nexthop Interface Active
------------------------------------------------------------------------------
192.168.250.0/24 5 1 ID 10.200.10.1 to-ser1 Y
==============================================================================
*A:ALA-12#
*A:ALA-12# show router 3 static-route preference 4
=============================================================================
Route Table
==============================================================================
IP Addr/mask Pref Metric Type Nexthop Interface Active
------------------------------------------------------------------------------
192.168.254.0/24 4 1 BH black-hole n/a Y
==============================================================================
*A:ALA-12#
*A:ALA-12# show router 3 static-route next-hop 10.10.0.254
==============================================================================
Route Table
==============================================================================
IP Addr/mask Pref Metric Type Nexthop Interface Active
------------------------------------------------------------------------------
192.168.253.0/24 5 1 NH 10.10.0.254 n/a N
=============================================================================
*A:ALA-12#
*A:Dut-B# show router static-route
===============================================================================
Static Route Table (Router: Base) Family: IPv4
===============================================================================
Prefix Tag Met Pref Type Act
Next Hop Interface
-------------------------------------------------------------------------------
10.2.3.4/32 0 1 5 NH Y
10.11.25.6
ip-10.11.25.5_base_to_cpe_static
10.11.15.0/24 0 1 5 NH Y
10.11.25.6
ip-10.11.25.5_base_to_cpe_static
-------------------------------------------------------------------------------
No. of Static Routes: 2
===============================================================================
*A:Dut-B# show router static-route detail
==============================================================================
Static Route Table (Router: Base) Family: IPv4
==============================================================================
Network : 10.2.3.4/32
Nexthop : 10.11.25.6
Type : Nexthop Nexthop Type : IP
Interface : ip-10.11.25.5_base_to_cpe_stat* Active : Y
Metric : 1 Preference : 5
Admin State : Up Tag : 0
BFD : disabled
CPE-check : enabled State : n/a
Target : 10.11.18.6
Interval : 1 Drop Count : 3
Log : N
CPE Host Up Time : 0d 00:00:02
CPE Echo Req Tx : 3 CPE Echo Reply Rx : 3
CPE Up Trans : 1 CPE Down Trans : 0
CPE TTL : 2
------------------------------------------------------------------------------
Network : 10.11.15.0/24
Nexthop : 10.11.25.6
Type : Nexthop Nexthop Type : IP
Interface : ip-10.11.25.5_base_to_cpe_stat* Active : Y
Metric : 1 Preference : 5
Admin State : Up Tag : 0
BFD : disabled
CPE-check : disabled
------------------------------------------------------------------------------
No. of Static Routes: 2
==============================================================================| Label | Description |
|---|---|
|
IP Addr/mask |
The static route destination address and mask. |
|
Pref |
The route preference value for the static route. |
|
Metric |
The route metric value for the static route. |
|
Type |
BH — The static route is a blackhole route. The next hop for this type of route is black hole. ID — The static route is an indirect route, where the next hop for this type of route is the non-directly connected next hop. NH — The route is a static route with a directly connected next hop. The next hop for this type of route is either the next-hop IP address or an egress IP interface name. |
|
Next Hop |
The next hop for the static route destination. |
|
Interface |
The egress IP interface name for the static route. n/a — indicates there is no current egress interface because the static route is inactive or a blackhole route. |
|
Active |
N — The static route is inactive; for example, the static route is disabled or the next hop IP interface is down. Y — The static route is active. |
|
No. of Routes |
The number of routes displayed in the list. |
tunnel-table [ip-address[/mask] [protocol protocol | sdp sdp-id]
tunnel-table [summary]
show>router
Supported on all 7210 SAS platforms as described in this document
This command displays tunnel table information.
When the auto-bind command is used when configuring a VPRN service, it means the MP-BGP NH resolution is referring to core routing instance for IP reachability. For a VPRN service, this object specifies the lookup to be used by the routing instance, if no SDP to the destination exists.
Displays the specified tunnel table destination IP address and mask.
Displays LDP protocol information.
Displays information pertaining to the specified SDP.
Displays summary tunnel table information.
The following output is an example of tunnel table information, and Table: Output fields: tunnel table describes the output fields.
Sample output*A:ALA-12>config>service# show router 3 tunnel-table summary
=============================================================================
Tunnel Table Summary (Router: Base)
=============================================================================
Active Available
------------------------------------------------------------------------------
LDP 1 1
SDP 1 1
==============================================================================
*A:ALA-12>config>service# | Label | Description |
|---|---|
|
Destination |
The route destination address and mask. |
|
Owner |
Specifies the tunnel owner. |
|
Encap |
Specifies the tunnel encapsulation type. |
|
Tunnel ID |
Specifies the tunnel (SDP) identifier. |
|
Pref |
Specifies the route preference for routes learned from the configured peers. |
|
Nexthop |
The next hop for the route destination. |
|
Metric |
The route metric value for the route. |