Configuring Ethernet Port Parameters

Use the following CLI syntax to configure Ethernet network and access port parameters. For more information about the dot1x command, see Configuring 802.1x Authentication Port Parameters. For more information about the mac-auth and mac-auth-wait commands, see Configuring MAC Authentication Port Parameters.

When an Ethernet port is configured in WAN mode (xgig wan command), users can change specific SONET/SDH parameters to reflect the SONET/SDH requirements for the port. For more information, see Configuring SONET/SDH Parameters on an Ethernet XGIG WAN Port.

CLI Syntax:

config# port port-id 
ethernet
    access 
        egress
            unshaped-sap-cir cir-rate
    autonegotiate limited
    cfm-loopback priority {low | high | dot1p} [match-vlan {vlan-range | none}]
    crc-monitor
        sd-threshold threshold [multiplier multiplier]
        no sd-threshold
        sf-threshold threshold [multiplier multiplier]
        no sf-threshold
        window-size seconds
        no window-size
    dot1q-etype 0x0600..0xffff 
    dot1x 
        [no] mac-auth
        mac-auth-wait seconds
        no mac-auth-wait
        [no] max-auth-req max-auth-request
        [no] port-control {auto | force-auth | force-unauth} 
        [no] quiet-period seconds 
        [no] radius-plcy name 
        [no] re-auth-period seconds 
        [no] re-authentication 
        [no] server-timeout seconds 
        [no] supplicant-timeout seconds 
        [no] transmit-period seconds 
    down-when-looped 
        [no] keep-alive timer 
        [no] retry-timeout timer 
        [no] shutdown
        [no] use-broadcast-address 
    duplex {full|half}
    efm-oam
        [no] accept-remote-loopback
        hold-time time-value
        [no] ignore-efm-state
        mode {active | passive}
        [no] shutdown
        transmit-interval interval [multiplier multiplier]
        [no]tunneling
    egress-rate sub-rate [include-fcs] [allow-eth-bn-rate-changes] [hold-time hold-time]
    encap-type {dot1q|null|qinq}
    hold-time hold-time [up hold-time-up | down 
    hold-time-down]
    ingress-rate ingress-rate cbs {size [bytes | kilobytes] | default} 
    no ingress-rate
        src-pause
        no src-pause
    lacp-tunnel
    lldp
        dest-mac
    loopback {line | internal} {timer {0 | 30..86400} | persistent} [swap-src-dst-mac] 
    no loopback
    mac ieee-address
    mode {access | network | hybrid} 
    mtu mtu-bytes
    network
        accounting-policy policy-id
        [no] collect-stats 
        queue-policy name
        scheduler-mode {profile | 4-priority | 16-priority}
    phy-tx-clock {auto-pref-master | auto-pref-slave | slave | master} 
    no phy-tx-clock
    poe {plus} 
    no poe
    ptp-asymmetry nano-seconds 
    no ptp-asymmetry 
    qinq-etype 0x0600..0xffff 
    report-alarm [signal-fail] [remote] [local] [no-frame-lock] [high-ber]
    speed {10|100|1000}
    ssm
        code-type {sonet | sdh}
        [no] shutdown
        [no] tx-dus
    vlan-filter filter-id
    no vlan-filter 
    xgig {lan | wan}
    xor-mode {rj45 | sfp}