Frame relay service can be configured on the following ports:
16-port T1/E1 ASAP Adapter card on DS1 or E1 ports
32-port T1/E1 ASAP Adapter card on DS1 or E1 ports
4-port DS3/E3 Adapter card on clear channel DS3 or E3 ports, or on DS3 ports channelized to DS1 or E1 down to DS0
12-port Serial Data Interface card on V.35 or X.21 serial ports
Frame relay ports can be configured in access mode to support:
Fpipes on:
16-port T1/E1 ASAP Adapter card on DS1 or E1 ports
32-port T1/E1 ASAP Adapter card on DS1 or E1 ports
4-port DS3/E3 Adapter card on clear channel DS3 or E3 ports, or on DS3 ports channelized to DS1 or E1 down to DS0
12-port Serial Data Interface card on V.35 or X.21 serial ports
Ipipes on:
16-port T1/E1 ASAP Adapter card on DS1 or E1 ports
32-port T1/E1 ASAP Adapter card on DS1 or E1 ports
4-port DS3/E3 Adapter card on clear channel DS3 or E3 ports only
12-port Serial Data Interface card on V.35 or X.21 serial ports
The encap-type must be set to frame-relay. The settings for the frame relay port can be modified by using the parameters under the frame-relay command hierarchy as shown in the following examples. The settings apply to frame relay ports used for Fpipe SAPs and interworking Ipipe SAPs. See the 7705 SAR Services Guide for more information about frame relay VLL (Fpipe) services and IP interworking VLL (Ipipe) services.
Use the following CLI syntax to configure a frame relay access port on a 16-port T1/E1 ASAP Adapter card or a 32-port T1/E1 ASAP Adapter card.
port port-id
tdm
e1
channel-group channel-group-id
encap-type {atm|bcp-null|bcp-dot1q|ipcp| ppp-auto|frame-relay|wan-mirror|cisco-hdlc|cem|hdlc}
frame-relay
lmi-type {ansi | itu | none | rev1}
mode {dce | dte | bidir}
n393dce count
n393dte count
n391dte intervals
n392dce threshold
n392dte threshold
t391dte keepalive
t392dce keepalive
mode access
no shutdown
exit
no shutdown
exit
exit
no shutdown
Use the config port info detail command to display port configuration information:
*A:NOK-A>config>port# info detail
----------------------------------------------
description "DS1/E1"
tdm
e1
shutdown
framing g704
no loopback
clock-source node-timed
no signal-mode
report-alarm ais los
no report-alarm oof rai looped ber-sd ber-sf
no hold-time
ssm
shutdown
ssm-bit 8
no tx-dus
channel-group 1
shutdown
description "E1"
mode access
encap-type frame-relay
no mtu
network
queue-policy "default"
exit
timeslots 2-32
crc 16
frame-relay
lmi-type ansi
mode dte
n393dce 4
n393dte 4
n391dte 6
n392dce 3
n392dte 3
t391dte 10
t392dce 15
exit
exit
exit
line-impedance 120
exit
no shutdown
----------------------------------------------
*A:NOK-A>config>port#
Use the following CLI syntax to configure frame relay parameters for TDM DS3/E3 ports.
port port-id
tdm
ds3
encap-type {atm |bcp-null | bcp-dot1q | ipcp | ppp-auto | frame-relay | wan-mirror | cem}
mode {access | network}
frame-relay
lmi-type {ansi | itu | none | rev1}
mode {dce | dte | bidir}
n393dce count
n393dte count
n391dte intervals
n392dce threshold
n392dte threshold
t391dte keepalive
t392dce keepalive
no shutdown
exit
no shutdown
exit
exit
no shutdown
e3
encap-type {atm | bcp-null | bcp-dot1q | ipcp | ppp-auto | frame-relay | wan-mirror | cem}
mode {access | network}
frame-relay
lmi-type {ansi | itu | none | rev1}
mode {dce | dte | bidir}
n393dce count
n393dte count
n391dte intervals
n392dce threshold
n392dte threshold
t391dte keepalive
t392dce keepalive
no shutdown
exit
no shutdown
exit
exit
no shutdown
Use the following CLI syntax to configure frame relay parameters for V.35 serial ports. X.21 ports at super-rate speeds are also supported.
port port-id
serial
v35
channel-group channel-group-id
encap-type {cem | frame-relay | ipcp | hdlc | cisco-hdlc}
mode access
frame-relay
lmi-type {ansi | itu | none | rev1}
mode {dce | dte | bidir}
n393dce count
n393dte count
n391dte intervals
n392dce threshold
n392dte threshold
t391dte keepalive
t392dce keepalive
no shutdown
exit
no shutdown
exit
exit
no shutdown