port [port-id] [statistics] [detail]
port port-id acr [detail]
port port-id associations
port port-id cisco-hdlc
port port-id description
port port-id dot1x [detail]
port port-id ethernet [efm-oam | detail]
port port-id frame-relay [detail | dlci dlci]
port port-id ima-link
port port-id ppp [detail]
port aps[-group-id][.channel]
port lcr[-group-id/port][.channel]
show
This command displays port or channel information.
If no command line options are specified, the show port command displays summary information for all ports on provisioned adapter cards, fixed platforms, and modules.
If the detail keyword is specified without any port-id, a detailed output of every port in the system is displayed whether the ports are configured or not. This is useful for gathering full reports or as an input into the ‟| match” filtering command to display a customized summary of fields.
If the port-id parameter only specifies a portion of a port identifier, a summary of all ports that start with that portion is displayed. For example, specifying a slot number and an MDA number displays a summary of all ports on that MDA. If no port-id is specified, a summary of all ports in the system is displayed.
If the port identifier specifies a unique port, information about that port is displayed. The specific information displayed depends on the type of port. Additional information is displayed if the detail keyword is included. In addition, information subsets can be displayed by using various keywords. For example, the dot1x keyword displays only the dot1x information for the port.
specifies the physical port ID
Syntax
port-id |
slot[/mda[/port]] or slot/mda/port[.channel] |
|
where: |
||
slot |
1 |
|
mda |
1 to 6 |
7705 SAR-8 Shelf V2 |
1 to 12 and X1 to X4 |
7705 SAR-18 |
|
1 (Ethernet), 2 (T1/E1), or 3 (module) |
7705 SAR-M |
|
1 (Ethernet), 2 (module position 1), or 3 (module position 2) |
7705 SAR-H |
|
1 (Ethernet), 2 (RS-232) |
7705 SAR-Hc |
|
1 (Ethernet) or 2 (T1/E1) |
7705 SAR-A |
|
1 (Ethernet) or 2 (GNSS RF) |
7705 SAR-Ax |
|
1 (Ethernet) |
7705 SAR-Wx (Ethernet-only variants and Ethernet and PoE+ variants) |
|
3 (GPS) |
7705 SAR-Wx (variants with GPS) |
|
1 (for T1/E1 ports) 2 (for Ethernet XOR RJ-45 ports 2/1A and 2/2A, Ethernet XOR SFP ports 2/1B and 2/2B, Ethernet ports 2/3 to 2/6, and 10GigE SFP+ port 2/7) 3 (for Ethernet XOR RJ-45 ports 3/1A and 3/2A, Ethernet XOR SFP ports 3/1B and 3/2B, Ethernet ports 3/3 to 3/6, and 10GigE SFP+ port 3/7) |
7705 SAR-X |
|
port |
1 to 2 |
2-port OC3/STM1 Channelized Adapter card |
1 to 2 physical ports, 1 virtual port (designated as ‟v-port” or port 3) |
2-port 10GigE (Ethernet) Adapter card 2-port 10GigE (Ethernet) module |
|
1 to 4 |
4-port OC3/STM1 Clear Channel Adapter card 4-port OC3/STM1 / 1-port OC12/STM4 Adapter card 4-port DS3/E3 Adapter card 4-port SAR-H Fast Ethernet module |
|
1 to 6 |
6-port E&M Adapter card 6-port FXS Adapter card 6-port Ethernet 10Gbps Adapter card 6-port SAR-M Ethernet module |
|
1 to 8 |
8-port Gigabit Ethernet Adapter card 8-port Voice & Teleprotection card 8-port C37.94 Teleprotection card 8-port FXO Adapter card Packet Microwave Adapter card |
|
1 to 10 |
10-port 1GigE/1-port 10GigE X-Adapter card (10-port 1GigE mode) |
|
1 |
10-port 1GigE/1-port 10GigE X-Adapter card (1-port 10GigE mode) |
|
1 |
GPS Receiver module (GPS RF port) GNSS Receiver card (GNSS RF port) |
|
1 to 12 |
12-port Serial Data Interface card |
|
1 to 16 |
16-port T1/E1 ASAP Adapter card |
|
1 to 32 |
32-port T1/E1 ASAP Adapter card |
|
1 to 7 (Ethernet), 1 to 16 (T1/E1), or 1 (module) |
7705 SAR-M |
|
1 to 8 (Ethernet) |
7705 SAR-H |
|
1 to 6 (Ethernet), 1 to 2 (RS-232) |
7705 SAR-Hc |
|
1 to 2 (RS-232 ports) |
4-port T1/E1 and RS-232 Combination module |
|
3 to 4 (T1/E1 ports) |
4-port T1/E1 and RS-232 Combination module |
|
1 to 12 (Ethernet) or 1 to 8 (T1/E1) |
7705 SAR-A |
|
1 to 12 (Ethernet) or 1 (GNSS RF) |
7705 SAR-Ax |
|
1 to 5 (Ethernet) (on the Ethernet-only variants and Ethernet and PoE+ variants) or 1 (for GPS) |
7705 SAR-Wx |
|
1 to 8 (T1/E1 ports), 1 or 2 (Ethernet XOR RJ-45/SFP ports), 3 to 6 (Ethernet ports), 7 (Ethernet SFP+ ports) |
7705 SAR-X |
|
channel |
ds1, e1, codir, or tpif |
for config>port>tdm information |
em, fxo, or fxs |
for config>port>voice information |
|
rs232, rs530, v35, or x21 |
for config>port>serial information |
|
1 to 24 (DS1) or 1 to 32 (E1) |
for config>port>tdm>channel-group information |
|
1 (E&M) |
for config>port>voice>em>channel-group information |
|
1 (DS0) |
for config>port>tdm>codir>channel-group, config>port>tdm>tpif>channel-group, config>port>voice>fxo>channel-group, and config>port>voice>fxs>channel-group information |
|
1 (RS-232, RS-530, V.35, or X.21) |
for config>port>serial>channel-group information |
displays only port counter summary information
displays only port counter detail information
displays ACR-capable port information
displays ACR-capable port detail information
displays cHDLC port information
displays port description strings
displays statistics and status information about 802.1x ports
displays statistics and status detail information about 802.1x ports
displays a list of current router interfaces to which the port is associated
displays PPP protocol information for the port
displays PPP protocol detail information for the port
displays Ethernet port information
displays EFM OAM information
displays Ethernet port detail information
displays port-level frame relay statistics
displays frame relay port information
displays circuit-level frame relay statistics
displays port-level IMA link information
specifying only the keyword displays all the ports in APS groups. Specifying the group ID displays information about the specified APS group.
specifying only the keyword displays all the ports in LCR groups. Specifying the group ID and port displays information about the port in the specified LCR group.
The following outputs are examples of port information:
General (Output Example, Table: General Port Field Descriptions )
Port Statistics (Output Example, Table: Port Statistics Field Descriptions )
Specific, Ethernet (Output Example, Table: Specific Port Field Descriptions (GigE Port with Optical SFP))
Specific, PoE Enabled (Output Example, Table: PoE Port Field Descriptions (Ethernet))
Specific, Serial (Output Example, Table: Specific Port Field Descriptions (Serial Port))
Specific, SONET/SDH (Output Example, Table: Specific Port Field Descriptions (SONET/SDH Port))
Specific, Voice E&M (Output Example, Table: Specific Port Field Descriptions (E&M Voice Port))
Specific, Voice FXO (Output Example, Table: Specific Port Field Descriptions (FXO Voice Port))
Specific, Voice FXS (Output Example, Table: Specific Port Field Descriptions (FXS Voice Port))
Specific, DS0 Voice Channel Group (Output Example, Table: Specific Port Field Descriptions (DS0 Voice Channel Group))
Detail, SONET/SDH (Output Example, Table: Port Detail Field Descriptions (SONET/SDH Port) )
Detail, Ethernet (Ethernet Output Example (access mode), Table: Port Detail Field Descriptions (Ethernet, Access Mode))
Detail, Ethernet (Ethernet Output Example (network mode), Table: Port Detail Field Descriptions (Ethernet, Network Mode))
Detail, 10G Ring Ethernet (Output Example, Table: Port Detail Field Descriptions (Ring Ethernet))
Detail, 2.5G Virtual Ethernet (Output Example, Table: Port Detail Field Descriptions (v-port))
Detail, TDM/DS1 (Output Example (DS1), Table: Port Detail Field Descriptions (TDM DS1/E1 Interface) )
Detail, TDM/E1 (Output Example (E1), Table: Port Detail Field Descriptions (TDM DS1/E1 Interface) )
Serial Channel (Output Example, Table: Port Serial Channel Field Descriptions)
Voice Channel, E&M (Output Example, Table: Port Voice Channel Field Descriptions)
Channel Group (Output Example, Table: Port Channel Group Field Descriptions )
Channelized DS3 (Output Example, Table: Port Channelized DS3 Field Descriptions )
Clear Channel DS3 (Output Example, Table: Port Clear Channel DS3 Field Descriptions )
ACR Detail (Output Example, Table: Port ACR Detail Field Descriptions)
dot1x (Output Example, Table: Port dot1x Field Descriptions )
Descriptions (Output Example, Table: Port Description Field Descriptions)
Associations (Output Example, Table: Port Associations Field Descriptions )
IMA Link (Output Example, Table: Port IMA Link Field Descriptions)
Frame Relay (Output Example, Table: Port Frame Relay Field Descriptions)
Frame Relay DLCI (Output Example, Table: Port Frame Relay DLCI Field Descriptions)
HDLC and cHDLC (Output Example, Table: Port Frame Relay DLCI Field Descriptions)
TDM Codir or TPIF (Output Example, Table: Port Field Descriptions (TDM Codirectional or TPIF))
GNSS (Output Example, Table: Port Field Descriptions (GNSS))
Specific APS Port ID (Output Example, Table: Port Field Descriptions (With APS ID) )
Specific LCR Port ID (Output Example, Table: Port Field Descriptions (With LCR Port ID) )
*A:NOK-1># show port 1/1
==============================================================================
Ports on Slot 1
==============================================================================
Port Admin Link Port Cfg Oper LAG/ Port Port Port SFP/XFP/
Id State State MTU MTU Bndl Mode Encp Type MDIMDX
------------------------------------------------------------------------------
1/1/1 Down No Ghost
1/1/2 Down No Ghost
1/1/2.1 Down No Ghost 1514 1514 - accs cem serial
1/1/3 Down No Ghost
1/1/4 Down No Ghost
1/1/4.1 Down No Ghost 1514 1514 - accs cem serial
1/1/5 Down No Ghost
1/1/6 Down No Ghost
1/1/7 Down No Ghost
1/1/8 Down No Ghost
1/1/9 Down No Ghost
1/1/10 Down No Ghost
1/1/11 Down No Ghost
1/1/12 Down No Ghost
==============================================================================
*A:NOK-1># show port 1/2
==============================================================================
Ports on Slot 1
==============================================================================
Port Admin Link Port Cfg Oper LAG/ Port Port Port SFP/XFP/
Id State State MTU MTU Bndl Mode Encp Type MDIMDX
------------------------------------------------------------------------------
1/2/1 Down No Ghost
1/2/1.sts3 Up No Ghost 1524 1524 - accs atm sonet
1/2/2 Up No Ghost
1/2/2.sts3 Down No Ghost 1572 1572 - netw pppa sonet
1/2/3 Down No Ghost
1/2/4 Down No Ghost
==============================================================================
*A:NOK-1>#
A:NOK-1># show port 1/3
==============================================================================
Ports on Slot 1
==============================================================================
Port Admin Link Port Cfg Oper LAG/ Port Port Port SFP/XFP/
Id State State MTU MTU Bndl Mode Encp Type MDIMDX
------------------------------------------------------------------------------
1/3/1 Down No Ghost
1/3/1.1 Down No Ghost 1514 1514 - accs cem tdm
1/3/2 Down No Ghost
1/3/2.1 Down No Ghost 1514 1514 - accs cem tdm
1/3/3 Down No Ghost
1/3/4 Down No Ghost
1/3/5 Down No Ghost
1/3/6 Down No Ghost
1/3/7 Down No Ghost
1/3/8 Down No Ghost
1/3/9 Down No Ghost
1/3/10 Down No Ghost
1/3/11 Down No Ghost
1/3/12 Down No Ghost
1/3/13 Down No Ghost
1/3/14 Down No Ghost
1/3/15 Down No Ghost
1/3/16 Down No Ghost
1/3/16.1 Down No Ghost 1572 1572 - netw unkn tdm
==============================================================================
Label |
Description |
---|---|
Port ID |
The port ID configured or displayed in the slot/mda/port format |
Admin State |
Up: the administrative state is up |
Down: the administrative state is down |
|
Link |
Yes: a physical link is present |
No: a physical link is not present |
|
Port State |
Up: the port is physically present and has a physical link |
Down: the port is physically present but does not have a link |
|
Ghost: the port is not physically present |
|
None: the port is in its initial creation state or about to be deleted |
|
Link Up: the port is physically present and has a physical link. When Link Up appears at the lowest level of a TDM tributary, it means the physical connection is active but the port is waiting before data traffic can flow. It is a waiting state and indicates that data traffic will not flow until it transitions to the Up state. |
|
Link Down: the port is physically present but does not have a link |
|
Cfg MTU |
The configured MTU |
Oper MTU |
The negotiated size of the largest packet that can be sent on the port or channel specified in octets |
LAG/Bndl |
The Link Aggregation Group (LAG) or multilink bundle to which a TDM port is assigned |
Port Mode |
network: the port is configured for transport network use |
access: the port is configured for service access |
|
hybrid: the port is configured for hybrid use (transport network and service access per VLAN) |
|
Port Encp |
The encapsulation type on the port |
Port Type |
The type of port or optics installed |
SFP/MDI MDX |
The SFP type on an Ethernet port (Ethernet, Fast Ethernet, or GigE) |
*A:NOK-1># show port 1/1 statistics detail
===============================================================================
Port Statistics on Slot 1
===============================================================================
Port Ingress Ingress Egress Egress
Id Packets Octets Packets Octets
-------------------------------------------------------------------------------
1/1/1 0 0 0 0
1/1/1.rs232 0 0 0 0
1/1/2 0 0 0 0
1/1/2.rs232 0 0 0 0
1/1/2.1 0 0 0 0
1/1/3 0 0 0 0
1/1/4 0 0 0 0
1/1/4.v35 0 0 0 0
1/1/4.1 0 0 0 0
1/1/5 0 0 0 0
1/1/6 0 0 0 0
1/1/7 0 0 0 0
1/1/8 0 0 0 0
1/1/9 0 0 0 0
1/1/10 0 0 0 0
1/1/11 0 0 0 0
1/1/12 0 0 0 0
===============================================================================
*A:NOK-1>#
*A:NOK-1># show port 1/2 statistics detail
===============================================================================
Port Statistics on Slot 1
===============================================================================
Port Ingress Ingress Egress Egress
Id Packets Octets Packets Octets
-------------------------------------------------------------------------------
1/2/1 0 0 0 0
1/2/1.sts3 0 0 0 0
1/2/2 0 0 0 0
1/2/2.sts3 0 0 0 0
1/2/3 0 0 0 0
1/2/4 0 0 0 0
===============================================================================
*A:NOK-1>#
*A:NOK-1># show port 1/5 statistics detail
===============================================================================
Port Statistics on Slot 1
===============================================================================
Port Ingress Ingress Egress Egress
Id Packets Octets Packets Octets
-------------------------------------------------------------------------------
1/5/1 0 0 0 0
1/5/2 0 0 0 0
1/5/3 0 0 0 0
1/5/4 0 0 0 0
1/5/5 0 0 0 0
1/5/6 0 0 0 0
1/5/7 0 0 0 0
1/5/8 0 0 0 0
===============================================================================
*A:NOK-1>#
Label |
Description |
---|---|
Port ID |
The port ID configured or displayed in the slot/mda/port format |
Ingress Packets |
The number of ingress packets coming into the port |
Ingress Octets |
The number of ingress octets coming into the port |
Egress Packets |
The number of egress packets transmitted from the port |
Egress Octets |
The number of egress octets transmitted from the port |
*A:ALU-1># show port 1/5/8
===============================================================================
Ethernet Interface
===============================================================================
Description : 10/100/Gig Ethernet SFP
Interface : 1/5/8 Oper Speed : 1 Gbps
Link-level : Ethernet Config Speed : 1 Gbps
Admin State : up Oper Duplex : full
Oper State : up Config Duplex : full
Physical Link : Yes MTU : 1514
Single Fiber Mode : No
IfIndex : 40108032 Hold time up : 0 seconds
Last State Change : 11/24/2009 13:05:41 Hold time down : 0 seconds
Last Cleared Time : N/A DDM Events : Enabled
Phys State Chng Cnt: 0
Configured Mode : hybrid Encap Type : 802.1q
Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100
Ing. Pool % Rate : 100 Egr. Pool % Rate : 100
Ing. Acc. Wt. : 50 Egr. Acc. Wt. : 50
Ing. Net. Wt. : 50 Egr. Net. Wt. : 50
Net. Egr. Queue Pol: default
Auto-negotiate : true MDI/MDX : unknown
Net. Egr. ShaperPol: 2
Acc. Egr. ShaperPol: 5
Net. Scheduler Mode: 16-priority
Config Phy-tx-clock: auto-pref-slave Oper Phy-tx-clock: N/A
SapEgr.Unshaped-Cir: 0 Kbps
SapEgr.Shaper Pol : default
NetEgr.Unshaped-Cir: 0 Kbps
Allow Eth-BN : True
BN Egr.Rate in use : 765000 Eth-BN hold time : 6
Egress Rate : Default Ingress Rate : n/a
Egr.Rate Incl.FCS : Disabled
Ingress CBS(bytes) : 130816 Src-pause : Disabled
LACP Tunnel : Disabled
Down-when-looped : Disabled Keep-alive : 10
Loop Detected : False Retry : 120
Use Broadcast Addr : False
Loopback : none Swap Mac Addr : Disabled
Loopback Time Left : unspecified
Cfm Loopback : Disabled
Sync. Status Msg. : Enabled Rx Quality Level : 0xf(dus)
PTP Asymmetry : 0 Edge Timestamp : Disable
Timestamp Capable : True
CRC Mon SD Thresh : Disabled CRC Mon Window : 10 seconds
CRC Mon SF Thresh : Disabled
Configured Address : 00:1a:f0:d4:09:de
Hardware Address : 00:1a:f0:d4:09:de
Cfg Alarm :
Alarm Status :
Transceiver Data
Transceiver Status : operational
Transceiver Type : SFP
Model Number : 3HE00027AAAA02 ALU IPUIAELDAB
TX Laser Wavelength: 850 nm Diag Capable : yes
Connector Code : LC Vendor OUI : 00:90:65
Manufacture date : 2009/07/09 Media : Ethernet
Serial Number : PFS3UTC
Part Number : FTRJ8519P2BNL-A5
Optical Compliance : GIGE-SX
Link Length support: 300m for 50u MMF; 150m for 62.5u MMF
SFP Sync-E Capable : yes
===============================================================================
Transceiver Digital Diagnostic Monitoring (DDM), Internally Calibrated
===============================================================================
Value High Alarm High Warn Low Warn Low Alarm
-------------------------------------------------------------------------------
Temperature (C) +27.1 +95.0 +90.0 -20.0 -25.0
Supply Voltage (V) 3.31 3.90 3.70 2.90 2.70
Tx Bias Current (mA) 6.3 17.0 14.0 2.0 1.0
Tx Output Power (dBm) -4.47 -2.00 -2.00 -11.02 -11.74
Rx Optical Power (avg dBm) -20.51 1.00 -1.00 -18.01! -20.00!
===============================================================================
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 11076096 11075584
Packets 86532 86529
Errors 0 0
Utilization (30 seconds) 0.00% 0.00%
===============================================================================
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Unicast Packets 0 1
Multicast Packets 86532 86528
Broadcast Packets 0 0
Discards 0 0
Unknown Proto Discards 0
===============================================================================
===============================================================================
Port Discard Statistics
===============================================================================
Input Output
Inv L2 Packets : 0
Inv IP Packets : 0
CSM Ingress Queues CSM Egress Queues
Hi : 0 Common : 0
Low : 0
Ftp : 0
===============================================================================
===============================================================================
Ethernet CFM Statistics
===============================================================================
Cfm LbmRx : 0
Cfm LbReplyTx : 0 Cfm LbmDropped : 0
Num Bn Rate Chng : 1 Last BnRateChng : 04/12/2017 21:20:53
Valid BnmRx : 2 Last Valid BnmRx : 04/12/2017 21:21:10
Invalid BnmRx : 0
BnmOutOfRangeBW : 0
===============================================================================
===============================================================================
Ethernet-like Medium Statistics
==============================================================================
Alignment Errors : 0 Sngl Collisions : 0
FCS Errors : 0 Mult Collisions : 0
SQE Test Errors : 0 Late Collisions : 0
CSE : 0 Excess Collisns : 0
Too long Frames : 0 Int MAC Tx Errs : 0
Symbol Errors : 0 Int MAC Rx Errs : 0
In Pause Frames : 0 Out Pause Frames : 0
===============================================================================
*A:ALU-1>#
Label |
Description |
---|---|
Ethernet Interface |
|
Description |
A text description of the port |
Interface |
The port ID displayed in the slot/mda/port format |
Link-level |
The type of link for which the port is configured |
Admin State |
up: the administrative state is up |
down: the administrative state is down |
|
Oper State |
up: the operating state is up |
down: the operating state is down |
|
Reason Down |
Indicates that the port has gone down due to Link Loss Forwarding |
Physical Link |
Yes: a physical link is present |
No: a physical link is not present |
|
Single Fiber Mode |
Yes: single fiber mode |
No: not single fiber mode |
|
IfIndex |
The interface's index number, which reflects its initialization sequence |
Last State Change |
The last time that the operational status of the port changed state |
Last Cleared Time |
The time since the last clear |
Phys State Chng Cnt |
The physical state change counter. This counter increments when a fully qualified (debounced) transition occurs at the physical layer of an Ethernet port, including the following transitions of the port state as displayed in the show port slot/mda/port output:
This counter does not increment for changes only in the link protocol states. That is, if the physical link is up, any transitions of the port state due to link protocols (for example, 802.3ah EFM OAM, LACP, 802.1ag) do not cause the counter to increment. The following port state transitions are examples of transitions that are not counted:
|
Configured Mode |
network: the port is configured for transport network use |
access: the port is configured for service access |
|
hybrid: the port is configured for hybrid use (transport network and service access per VLAN) |
|
Dot1Q Ethertype |
The Ethertype expected when the port's encapsulation type is dot1q |
QinQ Ethertype |
The Ethertype expected when the port's encapsulation type is qinq |
Ing. Pool % Rate |
The amount of ingress buffer space, expressed as a percentage of the available buffer space, that will be allocated to the port or channel for ingress buffering |
Net. Egr. Queue Pol |
default: the default policy is used |
network: the network egress queue policy is used |
|
Egr. Sched. Pol |
The egress scheduling policy |
Net. Egr. ShaperPol |
The network egress shaper policy ID |
Acc. Egr. ShaperPol |
The access egress shaper policy ID |
Net. Scheduler Mode |
The network scheduler mode |
Auto-negotiate |
true: the link attempts to automatically negotiate the link speed and duplex parameters |
false: the duplex and speed values are used for the link |
|
Config Phy-tx-clock |
The mode used to establish timing control of a 1000Base-T port. The options are:
|
Oper Phy-tx-clock |
The operational value of the MASTER-SLAVE relationship of the 1000Base-T physical layer transmit clock. The options are:
|
SapEgr.Shaper Pol |
The SAP egress shaper policy for the port |
SapEgr.Unshaped-Cir |
The CIR rate for the aggregate of all the unshaped 4-priority SAPs on the port |
NetEgr.Unshaped-Cir |
The CIR rate for the aggregate of all the unshaped VLANs on the port |
Allow Eth-BN |
Indicates whether Ethernet Bandwidth Notification (ETH-BN) is allowed on the port: True or False |
BN Egr.Rate in use |
The egress rate in use based on the request from the ETH-BN server MEP |
Eth-BN hold time |
The configured hold time (in seconds) between an egress rate change based on a received Bandwidth Notification Message (BNM) and the next change request that will be accepted |
Egress Rate |
The maximum amount of egress bandwidth (in kilobits per second) that this Ethernet interface can generate |
Egr.Rate Incl.FCS |
The configured state of egress rate FCS inclusion: enabled or disabled |
Ingress CBS (bytes) |
Indicates the ingress committed buffer space |
Src-pause |
A notification to slow down the transmission rate when it exceeds the bandwidth limit |
LACP Tunnel |
Indicates whether LACP packet tunneling is enabled |
Down-when-looped |
Enabled: The down-when-looped feature is enabled on the port |
Disabled: The down-when-looped feature is disabled on the port |
|
Keep-alive |
The time interval between keepalive PDUs transmitted toward the network during loop detection by the down-when-looped feature |
Loop Detected |
Indicates whether a loop is detected on the port |
Retry |
The minimum wait time before the port is re-enabled after it is brought down due to a loop detection |
Use Broadcast Addr |
Indicates whether the down-when-looped feature has been configured to compare the destination MAC address of received PDUs to the broadcast MAC address instead of the MAC address of the port |
Loopback |
The type of loopback configured on the port, either line, internal, or none |
Swap Mac Addr |
Indicates whether MAC address swapping is enabled |
Loopback Time Left |
The number of seconds left in a timed loopback If there is no loopback configured or the configured loopback is latched, the value is unspecified If configured loopback is persistent, the value persistent. |
Cfm Loopback |
Indicates whether the CFM loopback is enabled |
Sync. Status Msg. |
Indicates whether Synchronization Status Messaging is enabled on the port |
PTP Asymmetry |
Indicates whether PTP asymmetry is enabled |
Edge Timestamp |
Indicates whether the edge timestamp is enabled |
Timestamp Capable |
Indicates whether the port is timestamp-capable |
CRC Mon SD Thresh |
Indicates the CRC signal degrade threshold value (1 to 9), if enabled |
CRC Mon SF Thresh |
Indicates the CRC signal fail threshold value (1 to 9), if enabled |
CRC Mon Window |
Indicates the CRC window sampling size value (5 to 60) |
Rx Quality Level |
The Synchronization Status Messaging quality level value received on the port |
Code-Type |
The Synchronization Status Messaging quality level code type |
Tx Quality Level |
The Synchronization Status Messaging quality level value transmitted on the port |
Tx DUS/DNU |
Indicates whether the transmission of the QL-DUS/DNU value in synchronization status messages is enabled or disabled on the port |
Configured Address |
The base chassis Ethernet MAC address |
Hardware Address |
The interface hardware- or system-assigned MAC address at its protocol sublayer |
Cfg Alarm |
The type of alarms to be logged and reported for the Ethernet port |
Alarm Status |
The current alarm state |
Oper Speed |
The operating speed of the interface |
Config Speed |
The configured speed of the interface |
Oper Duplex |
full: the link is operating at full-duplex mode half: the link is operating at half-duplex mode |
Config Duplex |
full: the link is set at full-duplex mode half: the link is set at half-duplex mode |
MTU |
The size of the largest packet that can be sent/received on the Ethernet physical interface, specified in octets |
Hold time up |
The link-up dampening time in seconds |
Hold time down |
The link-down dampening time in seconds |
Encap Type |
null: ingress frames will not use any tags or labels to delineate a service |
dot1q: ingress frames carry 802.1Q tags, where each tag signifies a different service |
|
qinq: ingress frames carry two 802.1Q tags, where the outer tag is the service provider tag and the inner tag is the customer service tag |
|
Egr. Pool % Rate |
The amount of egress buffer space, expressed as a percentage of the available buffer space, that will be allocated to the port or channel for egress buffering |
MDI/MDX |
Ethernet type |
Transceiver Data |
The following information is provided for a configured transceiver (SFP):
|
Transceiver Digital Diagnostic Monitoring (DDM), Internally Calibrated |
|
SFP manufacturers specifications guidelines contained in specification SFF-8472, for the following:
For the above categories, the following values are shown:
If alarms/warnings are raised, there will be an "!" in the output |
|
Traffic Statistics |
|
Octets Input/Output |
The total number of octets received and transmitted on the port |
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Errors Input/Output |
For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol. For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors. |
Utilization Input/Output |
An average computed over the configured interval presented as a percentage of the maximum possible utilization on the Ethernet port. |
Port Statistics |
|
Unicast packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Multicast packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a unicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a unicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Broadcast packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a unicast or multicast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a unicast or multicast address at this sublayer, including those that were discarded or not sent. |
Discards Input/Output |
The number of inbound/outbound packets chosen to be discarded to possibly free up buffer space |
Unknown proto discards Input/Output |
For packet-oriented interfaces, the number of packets received via the interface that were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing, the number of transmission units received via the interface that were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0. Unknown proto discards do not show up in the packet counts. |
Port Discard Statistics |
|
Inv L2 Packets Input |
The number of invalid packets discarded due to an unknown Layer 2 ID |
Inv IP Packets Input |
The number of invalid IP packets discarded |
CSM Ingress Queues Input |
The number of incoming control packets discarded |
CSM Egress Queues Output |
The number of outgoing control packets discarded |
Ethernet CFM Statistics |
|
Cfm LbmRx |
The number of LBMs received |
Cfm LbReplyTx |
The number of LBRs transmitted |
Cfm LbmDropped |
The number of LBMs dropped |
Num Bn Rate Chng |
The number of times that the port egress rate is dynamically changed based on Bandwidth Notification (BN) messages Note: not every bandwidth change indicated by a BNM triggers a port egress rate change |
Last BnRateChng |
The time that the port egress rate was last changed based on a BNM |
Valid BnmRx |
The number of valid BN messages received |
Last Valid BnmRx |
The time that the last valid BNM was received |
Invalid BnmRx |
The number of invalid BN messages received |
BnmOutOfRangeBW |
The number of BN messages received with a requested bandwidth that was out of range |
Ethernet-like Medium Statistics |
|
Alignment Errors |
The total number of packets received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but that had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets |
FCS Errors |
The number of frames received that are an integral number of octets in length but do not pass the FCS check |
SQE Errors |
The number of times that the SQE TEST ERROR is received |
CSE |
The number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame |
Too long Frames |
The number of frames received that exceed the maximum permitted frame size |
Symbol Errors |
For an interface operating at 100 Mb/s, the number of times there was an invalid data symbol when a valid carrier was present |
In Pause Frames |
The number of IEEE 802.3x pause frames received for flow control; traffic is momentarily disrupted |
Sngl Collisions |
The number of frames that are involved in a single collision, and are subsequently transmitted successfully |
Mult Collisions |
The number of frames that are involved in more than one collision and are subsequently transmitted successfully |
Late Collisions |
The number of times that a collision is detected later than one slotTime into the transmission of a packet |
Excess Collisns |
The number of frames for which a transmission fails due to excessive collisions |
Int MAC Tx Errs |
The number of frames for which a transmission fails due to an internal MAC sublayer transmit error |
Int MAC Rx Errs |
The number of frames for which a reception fails due to an internal MAC sublayer receive error |
Out Pause Frames |
The number of IEEE 802.3x pause frames sent for flow control; traffic is momentarily disrupted |
*A:ALU-1># show port 1/1/7 detail
===============================================================================
Ethernet Interface
===============================================================================
Description : 10/100/Gig Ethernet TX
Interface : 1/1/7 Oper Speed : N/A
Link-level : Ethernet Config Speed : 1 Gbps
Admin State : down Oper Duplex : N/A
Oper State : down Config Duplex : full
Physical Link : No MTU : 1514
Single Fiber Mode : No
IfIndex : 44302336 Hold time up : 0 seconds
Last State Change : 04/14/2014 14:05:25 Hold time down : 0 seconds
Last Cleared Time : N/A
Configured Mode : access Encap Type : Null
Dot1Q Ethertype : 0x8100
Ing. Pool % Rate : 100 Egr. Pool % Rate : 100
Net. Egr. Queue Pol: default
Auto-negotiate : true MDI/MDX : unknown
Config Phy-tx-clock: auto-pref-slave Oper Phy-tx-clock: N/A
Allow Eth-BN : True
BN Egr.Rate in use : 765000 Eth-BN hold time : 6
Egress Rate : Default Ingress Rate : n/a
Down-when-looped : Disabled Keep-alive : 10
Loop Detected : False Retry : 120
Use Broadcast Addr : False
Loopback : none Swap Mac Addr : Disabled
Loopback Time Left : unspecified
Cfm Loopback : Disabled
PoE Mode : None PoE Detection : Searching
Poe Class : Class 0 PoE Fault Reason : none
PoE Maximum Power : None PoE Power In Use : 0.0 watts
Sync. Status Msg. : Disabled Rx Quality Level : N/A
PTP Asymmetry : 0 Edge Timestamp : Disable
Timestamp Capable : False
CRC Mon SD Thresh : Disabled CRC Mon Window : 10 seconds
CRC Mon SF Thresh : Disabled
Configured Address : 6c:be:e9:b1:af:1b
Hardware Address : 6c:be:e9:b1:af:1b
Cfg Alarm :
Alarm Status :
Transceiver Data
Transceiver Status : not-equipped
===============================================================================
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 10728 14236
Packets 102 156
Errors 0 0
Utilization (30 seconds) 0.00% 0.00%
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Unicast Packets 102 101
Multicast Packets 0 52
Broadcast Packets 0 3
Discards 0 0
Unknown Proto Discards 0
===============================================================================
===============================================================================
Port Discard Statistics
===============================================================================
Input Output
Inv L2 Packets : 0
Inv IP Packets : 0
CSM Ingress Queues CSM Egress Queues
Hi : 0 Common : 0
Medium : 0
Low : 0
===============================================================================
===============================================================================
Port Control Statistics
===============================================================================
-------------------------------------------------------------------------------
Ingress Queue CTL Packets Octets
Forwarded : 0 0
Dropped : 0 N/A
Egress Queue CTL Packets Octets
Forwarded : 0 0
Dropped : 0 N/A
===============================================================================
===============================================================================
Ethernet-like Medium Statistics
===============================================================================
Alignment Errors : 0 Sngl Collisions : 0
FCS Errors : 0 Mult Collisions : 0
SQE Test Errors : 0 Late Collisions : 0
CSE : 0 Excess Collisns : 0
Too long Frames : 0 Int MAC Tx Errs : 0
Symbol Errors : 0 Int MAC Rx Errs : 0
In Pause Frames : 0 Out Pause Frames : 0
===============================================================================
===============================================================================
Ethernet CFM Statistics
===============================================================================
Cfm LbmRx : 0
Cfm LbReplyTx : 0 Cfm LbmDropped : 0
Num Bn Rate Chng : 1 Last BnRateChng : 04/12/2017 21:20:53
Valid BnmRx : 2 Last Valid BnmRx : 04/12/2017 21:21:10
Invalid BnmRx : 0
BnmOutOfRangeBW : 0
===============================================================================
*A:ALU-1>#
Label |
Description |
---|---|
Ethernet Interface |
|
Description |
A text description of the port |
Interface |
The port ID displayed in the slot/mda/port format |
Oper Speed |
The operating speed of the interface |
Link-level |
Ethernet: the port is configured as Ethernet |
Config Speed |
The configured speed of the interface |
Admin State |
up: the port is administratively up |
down: the port is administratively down |
|
Oper Duplex |
The operating duplex mode of the interface |
Oper State |
up: the port is operationally up |
down: the port is operationally down |
|
Config Duplex |
full: the link is configured to full-duplex mode |
half: the link is configured to half-duplex mode |
|
Physical Link |
Yes: a physical link is present |
No: a physical link is not present |
|
MTU |
The size of the largest packet that can be sent/received on the Ethernet physical interface, specified in octets |
Single Fiber Mode |
Yes: single fiber mode |
No: not single fiber mode |
|
IfIndex |
The interface’s index number, which reflects its initialization sequence |
Hold time up |
The link-up dampening time in seconds. The port link dampening timer value that reduces the number of link transitions reported to upper layer protocols. |
Last State Change |
The last time that the operational status of the port changed state |
Hold time down |
The link-down dampening time in seconds. The down timer controls the dampening timer for link down transitions. |
Last Cleared Time |
The time since the last clear |
Configured Mode |
network: the port is configured for transport network use |
access: the port is configured for service access |
|
hybrid: the port is configured for hybrid use (transport network and service access per VLAN) |
|
Encap Type |
null: ingress frames will not use any tags or labels to delineate a service |
dot1q: ingress frames carry 802.1Q tags, where each tag signifies a different service |
|
qinq: ingress frames carry two 802.1Q tags, where the outer tag is the service provider tag and the inner tag is the customer service tag |
|
Dot1Q Ethertype |
The protocol carried in a dot1q Ethernet frame |
Ing. Pool % Rate |
The amount of ingress buffer space, expressed as a percentage of the available buffer space, that will be allocated to the port for ingress buffering |
Egr. Pool % Rate |
The amount of egress buffer space, expressed as a percentage of the available buffer space, that will be allocated to the port for egress buffering |
Net.Egr. Queue Pol. |
The number of the associated network egress queue QoS policy, or default if the default policy is used |
Auto-negotiate |
true: the link attempts to automatically negotiate the link speed and duplex parameters |
false: the duplex and speed values are used for the link |
|
MDI/MDX |
Indicates the Ethernet interface type |
Config Phy-tx-clock |
The mode used to establish timing control of a 1000Base-T port. The options are:
|
Oper Phy-tx-clock |
The operational value of the master-slave relationship of the 1000Base-T physical layer transmit clock. The options are:
|
Allow Eth-BN |
Indicates whether Ethernet Bandwidth Notification (ETH-BN) is allowed on the port: True or False |
BN Egr.Rate in use |
The egress rate in use based on the request from the ETH-BN server MEP |
Eth-BN hold time |
The configured hold time (in seconds) between an egress rate change based on a received Bandwidth Notification Message (BNM) and the next change request that will be accepted |
Egress Rate |
The maximum amount of egress bandwidth (in kilobits per second) that this Ethernet interface can generate |
Ingress Rate |
The maximum amount of ingress bandwidth (in kilobits per second) that this Ethernet interface can generate |
Down-when-looped |
Enabled: The down-when-looped feature is enabled on the port |
Disabled: The down-when-looped feature is disabled on the port |
|
Keep-alive |
The time interval between keepalive PDUs transmitted toward the network during loop detection by the down-when-looped feature |
Loop Detected |
Indicates whether a loop is detected on the port |
Retry |
The minimum wait time before the port is re-enabled after it is brought down due to a loop detection |
Use Broadcast Addr |
Indicates whether the down-when-looped feature has been configured to compare the destination MAC address of received PDUs to the broadcast MAC address instead of the MAC address of the port |
Loopback |
The type of loopback configured on the port, either line, internal, or none |
Swap Mac Addr. |
Indicates whether MAC address swapping is enabled |
Loopback Time Left |
The number of seconds left in a timed loopback If there is no loopback configured or the configured loopback is latched, the value is unspecified. If configured loopback is persistent, the value persistent |
Cfm Loopback |
Indicates whether the CFM loopback is enabled |
PoE Mode |
Indicates whether the port is using Poe, PoE+, or if the PoE function is turned off (disabled) |
PoE Detection |
Indicates the detection state of the PoE port |
PoE Class |
Displays the class of the PoE device connected to the port, as defined in IEEE 802.3af |
PoE Fault Reason |
Displays the reason the PoE port is down if a fault is detected |
PoE Maximum Power |
Indicates the maximum amount of PoE power configured and available on the port |
PoE Power in Use |
Indicates the amount of PoE power being used by the port |
Sync. Status Msg. |
Indicates whether Synchronization Status Messaging is enabled on the port |
Rx Quality Level |
The Synchronization Status Messaging quality level value received on the port |
PTP Asymmetry |
Indicates whether PTP asymmetry is enabled |
Edge Timestamp |
Indicates whether the edge timestamp is enabled |
Timestamp Capable |
Indicates whether the port is timestamp-capable |
CRC Mon SD Thresh |
Indicates the CRC signal degrade threshold value (1 to 9), if enabled |
CRC Mon SF Thresh |
Indicates the CRC signal fail threshold value (1 to 9), if enabled |
CRC Mon Window |
Indicates the CRC window sampling size value (1 to 10) |
Configured Address |
The base chassis Ethernet MAC address |
Hardware Address |
The interface hardware- or system-assigned MAC address at its protocol sublayer |
Cfg Alarm |
The type of alarms to be logged and reported for the port |
Alarm Status |
The current alarm state |
Traffic Statistics |
|
Octets Input/Output |
The total number of octets received and transmitted on the port |
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Errors Input/Output |
For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol. For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors. |
Utilization Input/Output |
An average computed over the configured interval presented as a percentage of the maximum possible utilization on the Ethernet port. |
Port Statistics |
|
Unicast Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Multicast Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a unicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a unicast or broadcast address at this sublayer, including those that were discarded or not sent |
Broadcast Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a unicast or multicast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a unicast or multicast address at this sublayer, including those that were discarded or not sent. |
Discards Input/Output |
The number of inbound/outbound packets chosen to be discarded to possibly free up buffer space |
Unknown Proto Discards Input/Output |
For packet-oriented interfaces, the number of packets received via the interface that were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing, the number of transmission units received via the interface that were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0. Unknown proto discards do not show up in the packet counts |
Port Discard Statistics |
|
Inv L2 Packets Input |
The number of invalid packets that are discarded due to an unknown Layer 2 ID |
Inv IP Packets Input |
The number of invalid IP packets that are discarded |
CSM Ingress Queues Input |
The number of incoming control packets discarded |
CSM Egress Queues Output |
The number of outgoing control packets discarded |
Port Control Statistics |
|
Ingress Queue CTL |
The number of forwarded packets and octets, and the number of dropped packets, for the ingress control queue. For access ports, this statistic applies only to Ethernet cards. For network ports, this statistic applies to all adapter cards. |
Egress Queue CTL |
The number of forwarded packets and octets, and the number of dropped packets, for the egress control queue. For access ports, this statistic applies only to Ethernet cards. For network ports, this statistic applies to all adapter cards. |
Ethernet-like Medium Statistics |
|
Alignment Errors |
The total number of packets received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but that had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets |
FCS Errors |
The number of frames received that are an integral number of octets in length but do not pass the FCS check |
SQE Errors |
The number of times that the SQE TEST ERROR is received |
CSE |
The number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame |
Too long Frames |
The number of frames received that exceed the maximum permitted frame size |
Symbol Errors |
For an interface operating at 100 Mb/s, the number of times there was an invalid data symbol when a valid carrier was present |
In Pause Frames |
The number of IEEE 802.3x pause frames received for flow control; traffic is momentarily disrupted |
Sngl Collisions |
The number of frames that are involved in a single collision, and are subsequently transmitted successfully |
Mult Collisions |
The number of frames that are involved in more than one collision and are subsequently transmitted successfully |
Late Collisions |
The number of times that a collision is detected later than one slotTime into the transmission of a packet |
Excess Collisns |
The number of frames for which a transmission fails due to excessive collisions |
Int MAC Tx Errs |
The number of frames for which a transmission fails due to an internal MAC sublayer transmit error |
Int MAC Rx Errs |
The number of frames for which a reception fails due to an internal MAC sublayer receive error |
Out Pause Frames |
The number of IEEE 802.3x pause frames sent for flow control; traffic is momentarily disrupted |
Ethernet CFM Statistics |
|
Cfm LbmRx |
The number of LBMs received |
Cfm LbReplyTx |
The number of LBRs transmitted |
Cfm LbmDropped |
The number of LBMs dropped |
Num Bn Rate Chng |
The number of times that the port egress rate is dynamically changed based on Bandwidth Notification (BN) messages Note: not every bandwidth change indicated by a BNM triggers a port egress rate change |
Last BnRateChng |
The time that the port egress rate was last changed based on a BNM |
Valid BnmRx |
The number of valid BN messages received |
Last Valid BnmRx |
The time that the last valid BNM was received |
Invalid BnmRx |
The number of invalid BN messages received |
BnmOutOfRangeBW |
The number of BN messages received with a requested bandwidth that was out of range |
*A:ALU-1># show port 1/1/1
===============================================================================
Serial RS-232 Physical Interface
===============================================================================
Description : RS-232/V.35/X.21
Interface : 1/1/1 Port IfIndex : 35684352
Admin Status : down Oper Status : down
Physical Link : No
Type : rs232
===============================================================================
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 0 0
Discards 0 0
Unknown Proto Discards 0
===============================================================================
*A:ALU-1>#
Label |
Description |
---|---|
Serial RS-232 Physical Interface |
|
Description |
A text description of the port |
Interface |
The port ID displayed in the slot/mda/port format |
Port IfIndex |
The interface’s index number, which reflects its initialization sequence |
Admin Status |
up: the administrative state is up |
down: the administrative state is down |
|
Oper Status |
up: the operational state is up |
down: the operational state is down |
|
Physical Link |
Yes: a physical link is present |
No: a physical link is not present |
|
Type |
The type of serial interface |
Port Statistics |
|
Packets input/output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Discards input/output |
The number of inbound/outbound packets chosen to be discarded to possibly free up buffer space |
Unknown proto discards input/output |
For packet-oriented interfaces, the number of packets received at the interface that were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing, the number of transmission units received at the interface that were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0. |
*A:ALU-1># show port 1/2/1
===============================================================================
SONET/SDH Interface
===============================================================================
Description : OC-3 SONET/SDH
Interface : 1/2/1 Speed : oc3
Admin Status : up Oper Status : up
Physical Link : Yes Loopback Mode : none
Single Fiber Mode : No
Ing. Pool % Rate : 100 Egr. Pool % Rate : 100
APS Group : none APS Role : none
Clock Source : node Framing : sonet
Last State Change : 11/24/2009 13:05:56 Port IfIndex : 46170112
Last Cleared Time : N/A DDM Events : Enabled
J0 String : 0x01 Section Trace Mode : byte
Rx S1 Byte : 0x00 (stu) Rx K1/K2 Byte : 0x00/0x00
Tx S1 Byte : 0x00 (stu) Tx DUS/DNU : Disabled
Rx J0 String (Hex) : 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Cfg Alarm : loc lrdi lb2er-sf slof slos
Alarm Status :
BER SD Threshold : 6 BER SF Threshold : 3
Hold time up : 500 milliseconds
Hold time down : 0 milliseconds
Transceiver Data
Transceiver Status : operational
Transceiver Type : SFP
Model Number : 3HE00034AAAA02 ALU IPUIAEXDAB
TX Laser Wavelength: 1310 nm Diag Capable : yes
Connector Code : LC Vendor OUI : 00:00:00
Manufacture date : 2009/04/25 Media : SONET/SDH
Serial Number : 1XX200083926037
Part Number : FTM3101CSL2iAL
Optical Compliance : OC3-SR-MM
Link Length support: 2000m for 50u MMF; 2000m for 62.5u MMF
SFP Sync-E Capable : n/a
===============================================================================
Transceiver Digital Diagnostic Monitoring (DDM), Externally Calibrated
===============================================================================
Value High Alarm High Warn Low Warn Low Alarm
-------------------------------------------------------------------------------
Temperature (C) +36.6 +100.0 +95.0 -35.0 -40.0
Supply Voltage (V) 3.28 3.80 3.63 2.97 2.70
Tx Bias Current (mA) 8.2 60.0 50.0 0.2 0.1
Tx Output Power (dBm) -15.44 -13.00 -14.00 -20.00 -21.02
Rx Optical Power (avg dBm) -16.14 -9.00 -10.00 -33.00 -35.22
===============================================================================
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 0 0
Discards 0 0
Unknown Proto Discards 0
===============================================================================
*A:ALU-1># show
Label |
Description |
---|---|
SONET/SDH interface |
|
Description |
A text description of the port |
Interface |
The port ID displayed in the slot/mda/port format |
Speed |
The speed of a SONET/SDH port |
Admin Status |
up: the administrative state is up |
down: the administrative state is down |
|
Oper Status |
up: the operational state is up |
down: the operational state is down |
|
Physical Link |
Yes: a physical link is present |
No: a physical link is not present |
|
Loopback Mode |
The loopback mode on the port |
Single Fiber Mode |
Yes: single fiber mode No: not single fiber mode |
Ing. Pool % Rate |
The amount of ingress buffer space, expressed as a percentage of the available buffer space, that will be allocated to the port for ingress buffering |
Egr. Pool % Rate |
The amount of egress buffer space, expressed as a percentage of the available buffer space, that will be allocated to the port for egress buffering |
APS group |
The automatic protection switching group |
APS role |
The automatic protection switching group role |
Clock Source |
node: the link uses the internal clock when transmitting data loop: the link recovers the clock from the received data stream |
Framing |
sonet: the port is configured for SONET framing sdh: the port is configured for SDH framing |
Last State Change |
The last time that the operational status of the port changed state |
Port IfIndex |
The interface’s index number, which reflects its initialization sequence |
Last Cleared Time |
The time since the last clear |
DDM Events |
Enabled: digital diagnostic monitoring events is enabled for the port Disabled: digital diagnostic monitoring events is disabled for the port |
J0 String |
The section trace value that is sent to the far-end port |
Section Trace Mode |
byte: the section trace in the SONET section header is set in bytes string: a text string is used to identify the SONET section header increment-z0: an incremental STM ID is configured instead of a static value |
Rx S1 Byte |
The synchronization status message value of the received SONET/SDH S1 byte |
Rx K1/K2 Byte |
The value of the received SONET/SDH K1/K2 byte |
Tx S1 Byte |
The synchronization status message value of the transmitted SONET/SDH S1 byte |
Tx DUS/DNU |
Indicates whether the transmission of the QL-DUS/DNU value in synchronization status messages is enabled or disabled on the port |
Rx J0 String (Hex) |
The hex value of the received J0 |
Cfg Alarm |
The type of alarms to be logged and reported for the SONET/SDH port |
Alarm Status |
The current alarm state |
BER SD Threshold |
The configured threshold for line signal degradation BER error rate, that when crossed determines the signal degradation and signal failure |
BER SF Threshold |
The configured threshold for line signal failure BER error rate, that when crossed determines the signal degradation and signal failure |
Hold time up |
The hold-timer value for link-up event dampening |
Hold time down |
The hold-timer value for link-down event dampening |
Transceiver Data |
The following information is provided for a configured transceiver (SFP):
|
Transceiver Digital Diagnostic Monitoring (DDM), Externally Calibrated |
|
SFP manufacturers specifications guidelines contained in specification SFF-8472, for the following:
For the above categories, the following values are shown:
If alarms/warnings are raised, an "!" is included in the output |
|
Port Statistics |
|
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Discards Input/Output |
The number of inbound/outbound packets chosen to be discarded to possibly free up buffer space |
Unknown proto discards Input/Output |
For packet-oriented interfaces, the number of packets received at the interface that were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing, the number of transmission units received at the interface that were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0. |
*A:ALU-1># show port 1/1/1
===============================================================================
Voice Physical Interface
===============================================================================
Description : E&M
Interface : 1/1/1 Port IfIndex : 41975808
Admin Status : up Oper Status : up
Physical Link : Yes
Type : em
TLP Rx : 0.0 Audio Wires : four-wires
TLP Tx : 0.0
===============================================================================
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 106012 105984
Discards 0 0
Unknown Proto Discards 0
===============================================================================
*A:ALU-1>#
Label |
Description |
---|---|
Voice Physical Interface |
|
Description |
A text description of the port |
Interface |
The port ID displayed in the slot/mda/port format |
Port IfIndex |
The interface's index number, which reflects its initialization sequence |
Admin Status |
up: the administrative state is up |
down: the administrative state is down |
|
Oper Status |
up: the operating state is up |
down: the operating state is down |
|
Physical Link |
Yes: a physical link is present |
No: a physical link is not present |
|
Type |
The type of voice interface |
TLP Rx |
The receive transmission level point value for the port |
Audio Wires |
Four-wire or two-wire (for E & M only) |
TLP Tx |
The transmit transmission level point value for the port |
Port Statistics |
|
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Discards Input/Output |
The number of inbound/outbound packets chosen to be discarded to possibly free up buffer space |
Unknown Proto Discards Input/Output |
For packet-oriented interfaces, the number of packets received at the interface that were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing, the number of transmission units received at the interface that were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0. |
*A:ALU-1># show port 1/1/5
===============================================================================
Voice Physical Interface
===============================================================================
Description : FXO
Interface : 1/1/5 Port IfIndex : 39878656
Admin Status : down Oper Status : down
Physical Link : no
Type : fxo Signaling Type : 3600ls
TLP Rx : 0.0 Line Balance : nominal
TLP Tx : 0.0
===============================================================================
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 0 0
Discards 0 0
Unknown Proto Discards 0
===============================================================================
*A:ALU-1>#
Label |
Description |
---|---|
Voice Physical Interface |
|
Description |
A text description of the port |
Interface |
The port ID displayed in the slot/mda/port format |
Port IfIndex |
The interface's index number, which reflects its initialization sequence |
Admin Status |
up: the administrative state is up |
down: the administrative state is down |
|
Oper Status |
up: the operating state is up |
down: the operating state is down |
|
Physical Link |
Yes: a physical link is present |
No: a physical link is not present |
|
Type |
The type of voice interface (fxo) |
Signaling Type |
The signaling type: Mu-law: 3600ls—loop start A-law: 1511profile1—1511 loop start 3600re—remote extension 1511sn137—1511 profile 137 |
TLP Rx |
The receive transmission level point value for the port |
Line Balance |
nominal or 800 |
TLP Tx |
The transmit transmission level point value for the port |
Port Statistics |
|
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Discards Input/Output |
The number of inbound/outbound packets chosen to be discarded to possibly free up buffer space |
Unknown Proto Discards Input/Output |
For packet-oriented interfaces, the number of packets received at the interface that were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing, the number of transmission units received at the interface that were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0. |
*A:ALU-1># show port 1/6/1
===============================================================================
Voice Physical Interface
===============================================================================
Description : FXO
Interface : 1/1/5 Port IfIndex : 39878656
Admin Status : down Oper Status : down
Physical Link : no
Type : fxs Signaling Type : 3600ls
TLP Rx : -3.0 Line Balance : nominal
TLP Tx : 0.0 Ring Generation : 16
===============================================================================
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 0 0
Discards 0 0
Unknown Proto Discards 0
===============================================================================
*A:ALU-1>#
Label |
Description |
---|---|
Voice Physical Interface |
|
Description |
A text description of the port |
Interface |
The port ID displayed in the slot/mda/port format |
Port IfIndex |
The interface's index number, which reflects its initialization sequence |
Admin Status |
up: the administrative state is up |
down: the administrative state is down |
|
Oper Status |
up: the operating state is up |
down: the operating state is down |
|
Physical Link |
Yes: a physical link is present |
No: a physical link is not present |
|
Type |
The type of voice interface (fxs) |
Signaling Type |
The signaling type: Mu-law: 3600ls—loop start 3600plar—private line automatic ringdown A-law: 1511plar—1511 private line automatic ringdown 3600plar—private line automatic ringdown 1511profile1—1511 loop start 3600re—remote extension 1511sn137—1511 profile 137 |
TLP Rx |
The receive transmission level point value for the port |
Line Balance |
nominal or 800 |
TLP Tx |
The transmit transmission level point value for the port |
Ring Generation |
The frequency of the generated ring signal |
Port Statistics |
|
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Discards Input/Output |
The number of inbound/outbound packets chosen to be discarded to possibly free up buffer space |
Unknown Proto Discards Input/Output |
For packet-oriented interfaces, the number of packets received at the interface that were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing, the number of transmission units received at the interface that were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0. |
*A:ALU-1># show port 1/6/1.1
===============================================================================
Voice DS0 Chan Group
===============================================================================
Description : DS0GRP
Interface : 1/6/1.1
Admin Status : down Oper Status : down
Last State Change : 01/31/2011 16:06:07 Chan-Grp IfIndex : 572555325
Configured Mode : access Encap Type : cem
Admin MTU : 1514 Oper MTU : 1514
Physical Link : No
===============================================================================
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 0 0
Packets 0 0
Errors 0 0
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 0 0
Discards 0 0
Unknown Proto Discards 0
===============================================================================
Label |
Description |
---|---|
Voice |
|
Description |
A text description of the port |
Interface |
The port ID displayed in the slot/mda/port format |
Admin Status |
up: the administrative state is up |
down: the administrative state is down |
|
Oper Status |
up: the operating state is up |
down: the operating state is down |
|
Chan-grp IfIndex |
The channel group’s index number, which reflects its initialization sequence |
Last State Change |
Date and time of last state change |
Configured Mode |
short, long, nominal or 800 |
Admin MTU |
The configured MTU |
Physical Link |
Yes: a physical link is present |
No: a physical link is not present |
|
Encap Type |
The transmit transmission level point value for the port |
Oper MTU |
The negotiated size of the largest packet that can be sent on the port or channel specified in octets |
Traffic Statistics |
|
Octets Input/Output |
The total number of octets received and transmitted on the port |
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Errors Input/Output |
For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol. For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors. |
Port Statistics |
|
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Discards Input/Output |
The number of inbound/outbound packets chosen to be discarded to possibly free up buffer space |
Unknown proto discards Input/Output |
For packet-oriented interfaces, the number of packets received at the interface that were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing, the number of transmission units received at the interface that were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0. |
*A:ALU-1># show port 1/2/2 detail
================================================================================
SONET/SDH Interface
===============================================================================
Description : OC-3 SONET/SDH
Interface : 1/2/2 Speed : oc3
Admin Status : up Oper Status : up
Physical Link : Yes Loopback Mode : none
Single Fiber Mode : No
Ing. Pool % Rate : 100 Egr. Pool % Rate : 100
APS Group : none APS Role : none
Clock Source : node Framing : sonet
Last State Change : 12/02/2009 11:14:23 Port IfIndex : 46170112
Last Cleared Time : N/A DDM Events : Enabled
J0 String : 0x01 Section Trace Mode : byte
Rx S1 Byte : 0x00 (stu) Rx K1/K2 Byte : 0x00/0x00
Tx S1 Byte : 0x00 (stu) Tx DUS/DNU : Disabled
Rx J0 String (Hex) : 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Cfg Alarm : loc lrdi lb2er-sf slof slos
Alarm Status :
BER SD Threshold : 6 BER SF Threshold : 3
Hold time up : 500 milliseconds
Hold time down : 0 milliseconds
Transceiver Data
Transceiver Status : operational
Transceiver Type : SFP
Model Number : 3HE00034AAAA02 ALU IPUIAEXDAB
TX Laser Wavelength: 1310 nm Diag Capable : yes
Connector Code : LC Vendor OUI : 00:00:00
Manufacture date : 2009/04/25 Media : SONET/SDH
Serial Number : 1XX200083926037
Part Number : FTM3101CSL2iAL
Optical Compliance : OC3-SR-MM
Link Length support: 2000m for 50u MMF; 2000m for 62.5u MMF
SFP Sync-E Capable : n/a
=========================
Sonet Section
=========================
ES-S : 2
SES-S : 1
SEFS-S : 0
CV-S : 65561
LOS : 0
LOC : 0
LOF : 0
OOF : 0
B1 Error : 0
=========================
===========================================
Sonet Line
===========================================
Far End
-------------------------------------------
ES-L : 2 3
SES-L : 1 3
UAS-L : 0 0
CV-L : 49425 0
AIS-L : 0
RDI-L : 1
B2 Error : 0
S1 Error : 0
M1 Error : 24834
===========================================
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 0 0
Discards 0 0
Unknown Proto Discards 0
===============================================================================
*A:ALU-1>#
Label |
Description |
---|---|
SONET/SDH interface |
|
Description |
A text description of the port |
Interface |
The port ID displayed in the slot/mda/port format |
Speed |
The speed of a SONET/SDH port |
Admin Status |
up: the administrative state is up |
down: the administrative state is down |
|
Oper Status |
up: the operational state is up |
down: the operational state is down |
|
Physical Link |
Yes: a physical link is present |
No: a physical link is not present |
|
Loopback Mode |
The loopback mode on the port |
Single Fiber Mode |
Yes: single fiber mode No: not single fiber mode |
Ing. Pool % Rate |
The amount of ingress buffer space, expressed as a percentage of the available buffer space, that will be allocated to the port for ingress buffering |
Egr. Pool % Rate |
The amount of egress buffer space, expressed as a percentage of the available buffer space, that will be allocated to the port for egress buffering |
Clock Source |
node: the link uses the internal clock when transmitting data loop: the link recovers the clock from the received data stream |
Framing |
sonet: the port is configured for SONET framing sdh: the port is configured for SDH framing |
Last State Change |
The last time that the operational status of the port changed state |
Port IfIndex |
The interface’s index number, which reflects its initialization sequence |
Last Cleared Time |
The time since the last clear |
DDM Events |
Enabled: digital diagnostic monitoring events is enabled for the port Disabled: digital diagnostic monitoring events is disabled for the port |
J0 String |
The section trace value that is sent to the far-end port |
Section Trace Mode |
byte: the section trace in the SONET section header is set in bytes string: a text string is used to identify the SONET section header increment-z0: an incremental STM ID is configured instead of a static value |
Rx S1 Byte |
The synchronization status message value of the received SONET/SDH S1 byte |
Rx K1/K2 Byte |
The value of the received SONET/SDH K1/K2 byte |
Tx S1 Byte |
The synchronization status message value of the transmitted SONET/SDH S1 byte |
Tx DUS/DNU |
Indicates whether the transmission of the QL-DUS/DNU value in synchronization status messages is enabled or disabled on the port |
Rx J0 String (Hex) |
The hex value of the received J0 |
Cfg Alarm |
The type of alarms to be logged and reported for the SONET/SDH port |
Alarm Status |
The current alarm state |
BER SD Threshold |
The configured threshold for line signal degradation BER error rate, that when crossed determines the signal degradation and signal failure |
BER SF Threshold |
The configured threshold for line signal failure BER error rate, that when crossed determines the signal degradation and signal failure |
Hold time up |
The hold-timer value for link-up event dampening |
Hold time down |
The hold-timer value for link-down event dampening |
Transceiver Data |
The following information is provided for a configured SFP:
|
Sonet Section |
|
ES-S |
The number of Errored Seconds errors |
SES-S |
The number of Severely Errored Seconds errors |
SEFS-S |
The number of Severely Errored Framing Seconds errors |
CV-S |
The number of Code Violations errors |
LOS |
The number of Loss of Signal errors |
LOC |
The number of Loss of Clock errors |
LOF |
The number of Loss of Frame errors |
OOF |
The number of Out of Frame errors |
B1 Error |
The number of B1 errors |
Sonet Line |
|
ES-L |
The number of Errored Seconds errors, at the near end and far end |
SES-L |
The number of Severely Errored Seconds errors, at the near end and far end |
UAS-L |
The number of Unavailable Seconds errors, at the near end and far end |
CV-L |
The number of Code Violations errors, at the near end and far end |
AIS-L |
The number of Alarm Indication Signal errors |
RDI-L |
The number of Remote Defect Indication errors |
B2 Error |
The number of B2 errors |
S1 Error |
The number of S1 errors |
M1 Error |
The number of M1 errors |
Port Statistics |
|
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Discards Input/Output |
The number of inbound/outbound packets chosen to be discarded to possibly free up buffer space |
Unknown proto discards Input/Output |
For packet-oriented interfaces, the number of packets received at the interface that were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing, the number of transmission units received at the interface that were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0. |
*A:ALU-1># show port 1/5/8 detail
===============================================================================
Ethernet Interface
===============================================================================
Description : 10/100/Gig Ethernet SFP
Interface : 1/5/8 Oper Speed : 1 Gbps
Link-level : Ethernet Config Speed : 1 Gbps
Admin State : up Oper Duplex : full
Oper State : up Config Duplex : full
Physical Link : Yes MTU : 1518
Single Fiber Mode : No
IfIndex : 44302336 Hold time up : 0 seconds
Last State Change : 10/04/2011 14:05:25 Hold time down : 0 seconds
Last Cleared Time : 10/04/2011 14:04:37 DDM Events : Enabled
Phys State Chng Cnt: 3
Configured Mode : access Encap Type : 802.1q
Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100
Ing. Pool % Rate : 100 Egr. Pool % Rate : 100
Net. Egr. Queue Pol: default
Auto-negotiate : true MDI/MDX : MDX
Net. Scheduler Mode: 16-priority
Config Phy-tx-clock: auto-pref-slave Oper Phy-tx-clock: slave
SapEgr.Unshaped-Cir: 0 Kbps
SapEgr.Shaper-Pol : EgrShprPolicy
NetEgr.Unshaped-Cir: 0 Kbps
Allow Eth-BN : True
BN Egr.Rate in use : 765000 Eth-BN hold time : 6
Egress Rate : 1111 Ingress Rate : n/a
Egr.Rate Incl.FCS : Disabled
Ingress CBS(bytes) : 130816 Src-pause : Disabled
LACP Tunnel : Disabled
Down-when-looped : Disabled Keep-alive : 10
Loop Detected : False Retry : 120
Use Broadcast Addr : False
Loopback : none Swap Mac Addr : Disabled
Loopback Time Left : unspecified
Cfm Loopback : Disabled
Sync. Status Msg. : Disabled Rx Quality Level : N/A
PTP Asymmetry : 0 Edge Timestamp : Disable
Timestamp Capable : False
Configured Address : 2001:db8::
Hardware Address : 2001:db8::
Cfg Alarm :
Alarm Status :
Transceiver Data
Transceiver Status : operational
Transceiver Type : SFP
Model Number : 3HE00062AAAA01 ALA IPUIAEHDAA
TX Laser Wavelength: 0 nm Diag Capable : no
Connector Code : Unknown Vendor OUI : 00:90:65
Manufacture date : 2010/01/15 Media : Ethernet
Serial Number : PH23PQS
Part Number : FCMJ-8521-3-A5
Optical Compliance : GIGE-T
Link Length support: 100m for copper
SFP Sync-E Capable : no
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 10728 14236
Packets 102 156
Errors 0 0
Utilization (30 seconds) 0.00% 0.00%
===============================================================================
Ethernet Statistics
===============================================================================
Broadcast Pckts : 3 Drop Events : 0
Multicast Pckts : 52 CRC/Align Errors : 0
Undersize Pckts : 0 Fragments : 0
Oversize Pckts : 0 Jabbers : 0
Collisions : 0
Octets : 24964
Packets : 258
Packets of 64 Octets : 54
Packets of 65 to 127 Octets : 204
Packets of 128 to 255 Octets : 0
Packets of 256 to 511 Octets : 0
Packets of 512 to 1023 Octets : 0
Packets of 1024 to 1518 Octets : 0
Packets of 1519 or more Octets : 0
===============================================================================
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Unicast Packets 102 101
Multicast Packets 0 52
Broadcast Packets 0 3
Discards 0 0
Unknown Proto Discards 0
===============================================================================
===============================================================================
Port Discard Statistics
===============================================================================
Input Output
Inv L2 Packets : 0 Port MTU Exceeded: 0
Inv MPLS Labels : 0
Inv IP Packets : 0
CSM Ingress Queues CSM Egress Queues
Hi : 0 Common : 0
Medium : 0
Low : 0
===============================================================================
===============================================================================
Port Control Statistics
===============================================================================
-------------------------------------------------------------------------------
Ingress Queue CTL Packets Octets
Forwarded : 102 13482
Dropped : 0 N/A
Egress Queue CTL Packets Octets
Forwarded : 56 3184
Dropped : 0 N/A
===============================================================================
===============================================================================
Ethernet CFM Statistics
===============================================================================
Cfm LbmRx : 0
Cfm LbReplyTx : 0 Cfm LbmDropped : 0
Num Bn Rate Chng : 1 Last BnRateChng : 04/12/2017 21:20:53
Valid BnmRx : 2 Last Valid BnmRx : 04/12/2017 21:21:10
Invalid BnmRx : 0
BnmOutOfRangeBW : 0
===============================================================================
===============================================================================
Ethernet-like Medium Statistics
===============================================================================
Alignment Errors : 0 Sngl Collisions : 0
FCS Errors : 0 Mult Collisions : 0
SQE Test Errors : 0 Late Collisions : 0
CSE : 0 Excess Collisns : 0
Too long Frames : 0 Int MAC Tx Errs : 0
Symbol Errors : 0 Int MAC Rx Errs : 0
In Pause Frames : 0 Out Pause Frames : 0
===============================================================================
Label |
Description |
---|---|
Ethernet Interface |
|
Description |
A text description of the port |
Interface |
The port ID displayed in the slot/mda/port format |
Oper Speed |
The operating speed of the interface |
Link-level |
Ethernet: the port is configured as Ethernet |
Config Speed |
The configured speed of the interface |
Admin State |
up: the port is administratively up |
down: the port is administratively down |
|
Oper Duplex |
The operating duplex mode of the interface |
Oper State |
up: the port is operationally up |
down: the port is operationally down |
|
Config Duplex |
full: the link is configured to full-duplex mode |
half: the link is configured to half-duplex mode |
|
Physical Link |
Yes: a physical link is present |
No: a physical link is not present |
|
MTU |
The size of the largest packet that can be sent/received on the Ethernet physical interface, specified in octets |
IfIndex |
The interface’s index number, which reflects its initialization sequence |
Hold time up |
The link-up dampening time in seconds. The port link dampening timer value that reduces the number of link transitions reported to upper layer protocols. |
Last State Change |
The last time that the operational status of the port changed state |
Hold time down |
The link-down dampening time in seconds. The down timer controls the dampening timer for link down transitions. |
Phys State Chng Cnt |
The physical state change counter. This counter increments when a fully qualified (debounced) transition occurs at the physical layer of an Ethernet port, including the following transitions of the port state as displayed in the show port slot/mda/port output:
This counter does not increment for changes only in the link protocol states. That is, if the physical link is up, any transitions of the port state due to link protocols (for example, 802.3ah EFM OAM, LACP, 802.1ag) do not cause the counter to increment. The following port state transitions are examples of transitions that are not counted:
|
Configured Mode |
network: the port is configured for transport network use |
access: the port is configured for service access |
|
hybrid: the port is configured for hybrid use (transport network and service access per VLAN) |
|
Encap Type |
null: ingress frames will not use any tags or labels to delineate a service |
dot1q: ingress frames carry 802.1Q tags, where each tag signifies a different service |
|
qinq: ingress frames carry two 802.1Q tags, where the outer tag is the service provider tag and the inner tag is the customer service tag |
|
Dot1Q Ethertype |
The protocol carried in a dot1q Ethernet frame |
QinQ Ethertype |
The protocol carried in a qinq Ethernet frame |
Net. Egr. Queue Pol. |
The number of the associated network egress queue QoS policy, or default if the default policy is used |
Auto-negotiate |
true: the link attempts to automatically negotiate the link speed and duplex parameters |
false: the duplex and speed values are used for the link |
|
Net. Scheduler Mode |
The network scheduler mode |
SapEgr.Unshaped-Cir |
The CIR rate for the aggregate of all the unshaped 4-priority SAPs on the port |
SapEgr.Shaper-Pol |
The access egress shaper policy ID |
NetEgr.Unshaped-Cir |
The CIR rate for the aggregate of all the unshaped VLANs on the port |
NetEgr. Shaper-Pol |
The network egress shaper policy ID |
Allow Eth-BN |
Indicates whether Ethernet Bandwidth Notification (ETH-BN) is allowed on the port: True or False |
BN Egr.Rate in use |
The egress rate in use based on the request from the ETH-BN server MEP |
Eth-BN hold time |
The configured hold time (in seconds) between an egress rate change based on a received Bandwidth Notification Message (BNM) and the next change request that will be accepted |
Egress Rate |
The maximum amount of egress bandwidth (in kilobits per second) that this Ethernet interface can generate |
Ingress Rate |
The maximum amount of ingress bandwidth (in kilobits per second) that this Ethernet interface can generate |
Egr.Rate Incl.FCS |
The configured state of egress rate FCS inclusion: enabled or disabled |
LACP Tunnel |
Indicates whether LACP packet tunneling is enabled |
Down-when-looped |
Enabled: The down-when-looped feature is enabled on the port |
Disabled: The down-when-looped feature is disabled on the port |
|
Keep-alive |
The time interval between keepalive PDUs transmitted toward the network during loop detection by the down-when-looped feature |
Loop Detected |
Indicates whether a loop is detected on the port |
Retry |
The minimum wait time before the port is re-enabled after it is brought down due to a loop detection |
Use Broadcast Addr |
Indicates whether the down-when-looped feature has been configured to compare the destination MAC address of received PDUs to the broadcast MAC address instead of the MAC address of the port |
Loopback |
The type of loopback configured on the port, either line, internal, or none |
Swap Mac Addr. |
Indicates whether MAC address swapping is enabled |
Loopback Time Left |
The number of seconds left in a timed loopback If there is no loopback configured or the configured loopback is latched, the value is unspecified. If configured loopback is persistent, the value persistent |
Cfm Loopback |
Indicates whether the CFM loopback is enabled |
Sync. Status Msg. |
Indicates whether Synchronization Status Messaging is enabled on the port |
Rx Quality Level |
The Synchronization Status Messaging quality level value received on the port |
Code-Type |
The Synchronization Status Messaging quality level code type, either SONET or SDH |
Tx Quality Level |
The Synchronization Status Messaging quality level value transmitted on the port |
Tx DUS/DNU |
Indicates whether the transmission of the QL-DUS/DNU value in synchronization status messages is enabled or disabled on the port |
Configured Address |
The base chassis Ethernet MAC address |
Hardware Address |
The interface hardware- or system-assigned MAC address at its protocol sublayer |
Cfg Alarm |
The type of alarms to be logged and reported for the port |
Alarm Status |
The current alarm state |
Transceiver Data |
The following information is provided for a configured transceiver (SFP):
|
Transceiver Digital Diagnostic Monitoring (DDM), Externally Calibrated |
|
SFP manufacturers specifications guidelines contained in specification SFF-8472, for the following:
For the above categories, the following values are shown:
If alarms/warnings are raised, there will be an "!" in the output |
|
Traffic Statistics |
|
Octets Input/Output |
The total number of octets received and transmitted on the port |
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Errors Input/Output |
For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol. For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors. |
Utilization Input/Output |
An average computed over the configured interval presented as a percentage of the maximum possible utilization on the Ethernet port. |
Ethernet Statistics |
|
Broadcast Pckts |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a unicast or multicast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a unicast or multicast address at this sublayer, including those that were discarded or not sent. |
Multicast Pckts |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a unicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a unicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Undersize Pckts |
The total number of packets received that were shorter than 64 octets (excluding framing bits, but including FCS octets) but were otherwise well formed |
Oversize Pckts |
The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets) but were otherwise well formed |
Collisions |
The best estimate of the total number of collisions on this Ethernet segment |
Drop Events |
The total number of times that packets were detected as being dropped due to a lack of resources (not necessarily the total number of packets dropped) |
CRC/Align Errors |
The total number of packets received that were between 64 and 1518 octets (excluding framing bits but including FCS octets) that had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error) |
Fragments |
The total number of packets received that were shorter than 64 octets (excluding framing bits but including FCS octets) that had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error) |
Jabbers |
The total number of packets received that were longer than 1518 octets (excluding framing bits but including FCS octets) that had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error) |
Octets |
Total number of octets received |
Packets |
Number of packets received, broken down by size |
Port Statistics |
|
Unicast Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Multicast Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a unicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a unicast or broadcast address at this sublayer, including those that were discarded or not sent |
Broadcast Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a unicast or multicast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a unicast or multicast address at this sublayer, including those that were discarded or not sent. |
Discards Input/Output |
The number of inbound/outbound packets chosen to be discarded to possibly free up buffer space |
Unknown Proto Discards Input/Output |
For packet-oriented interfaces, the number of packets received via the interface that were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing, the number of transmission units received via the interface that were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0. Unknown proto discards do not show up in the packet counts |
Port Discard Statistics |
|
Inv L2 Packets Input |
The number of invalid packets that are discarded due to an unknown Layer 2 ID |
Port MTU Exceeded |
Indicates that the port MTU has been exceeded |
Inv MPLS Labels |
The number of MPLS labels discarded |
Inv IP Packets Input |
The number of invalid IP packets that are discarded |
H. Policed Packets |
The number of packets that are discarded due to hard policing |
CSM Ingress Queues Input |
The number of incoming control packets discarded |
CSM Egress Queues Output |
The number of outgoing control packets discarded |
Port Control Statistics |
|
Ingress Queue CTL |
The number of forwarded packets and octets, and the number of dropped packets, for the ingress control queue. For access ports, this statistic applies only to Ethernet cards. For network ports, this statistic applies to all adapter cards. |
Egress Queue CTL |
The number of forwarded packets and octets, and the number of dropped packets, for the egress control queue. For access ports, this statistic applies only to Ethernet cards. For network ports, this statistic applies to all adapter cards. |
Ethernet CFM Statistics |
|
Cfm LbmRx |
The number of LBMs received |
Cfm LbReplyTx |
The number of LBRs transmitted |
Cfm LbmDropped |
The number of LBMs dropped |
Num Bn Rate Chng |
The number of times that the port egress rate is dynamically changed based on Bandwidth Notification (BN) messages Note: not every bandwidth change indicated by a BNM triggers a port egress rate change |
Last BnRateChng |
The time that the port egress rate was last changed based on a BNM |
Valid BnmRx |
The number of valid BN messages received |
Last Valid BnmRx |
The time that the last valid BNM was received |
Invalid BnmRx |
The number of invalid BN messages received |
BnmOutOfRangeBW |
The number of BN messages received with a requested bandwidth that was out of range |
Ethernet-like Medium Statistics |
|
Alignment Errors |
The total number of packets received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but that had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets |
FCS Errors |
The number of frames received that are an integral number of octets in length but do not pass the FCS check |
SQE Errors |
The number of times that the SQE TEST ERROR is received |
CSE |
The number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame |
Too long Frames |
The number of frames received that exceed the maximum permitted frame size |
Symbol Errors |
For an interface operating at 100 Mb/s, the number of times there was an invalid data symbol when a valid carrier was present |
In Pause Frames |
The number of IEEE 802.3x pause frames received for flow control; traffic is momentarily disrupted |
Sngl Collisions |
The number of frames that are involved in a single collision, and are subsequently transmitted successfully |
Mult Collisions |
The number of frames that are involved in more than one collision and are subsequently transmitted successfully |
Late Collisions |
The number of times that a collision is detected later than one slotTime into the transmission of a packet |
Excess Collisns |
The number of frames for which a transmission fails due to excessive collisions |
Int MAC Tx Errs |
The number of frames for which a transmission fails due to an internal MAC sublayer transmit error |
Int MAC Rx Errs |
The number of frames for which a reception fails due to an internal MAC sublayer receive error |
Out Pause Frames |
The number of IEEE 802.3x pause frames sent for flow control; traffic is momentarily disrupted |
The 7705 SAR counts both Ethernet packets with errors and valid Ethernet packets under Ethernet port statistics. For each received errored packet, both aggregate Ethernet statistics and the errored Ethernet statistics are incremented.
The show>port output for an Ethernet port in network mode is similar to the access mode output (see Ethernet Output Example (access mode)) with the addition of a section for queue statistics. The output example below shows only the queue statistics fields.
*A:ALU-1># show port 1/1/1 detail
===============================================================================
Ethernet Interface
===============================================================================
.....
===============================================================================
Queue Statistics
===============================================================================
-------------------------------------------------------------------------------
Ingress Queue 1 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 4626 6939000
Out Profile forwarded : 2425 3637500
Out Profile dropped : 0 0
Ingress Queue 2 Packets Octets
In Profile forwarded : 2022 3033000
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 3 Packets Octets
In Profile forwarded : 2024 3036000
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 4 Packets Octets
In Profile forwarded : 2404 3606000
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 5 Packets Octets
In Profile forwarded : 2396 3594000
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 6 Packets Octets
In Profile forwarded : 2342 3513000
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 7 Packets Octets
In Profile forwarded : 2306 3459000
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 8 Packets Octets
In Profile forwarded : 2301 3451500
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 9 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 10 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 11 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 12 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 13 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 14 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 15 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 16 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue CTL Packets Octets
Forwarded : 0 0
Dropped : 0 N/A
Unshaped Egress Queue 1 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 129084 193109664
Out Profile dropped : 0 0
Unshaped Egress Queue 2 Packets Octets
In Profile forwarded : 128674 192496304
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Unshaped Egress Queue 3 Packets Octets
In Profile forwarded : 128685 192512760
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Unshaped Egress Queue 4 Packets Octets
In Profile forwarded : 154389 230965944
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Unshaped Egress Queue 5 Packets Octets
In Profile forwarded : 154372 230940512
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Unshaped Egress Queue 6 Packets Octets
In Profile forwarded : 154306 230841776
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Unshaped Egress Queue 7 Packets Octets
In Profile forwarded : 154265 230780440
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Unshaped Egress Queue 8 Packets Octets
In Profile forwarded : 154261 230774456
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Total Egress from all Shaped and Unshaped Queues
Packets Octets
In Profile forwarded : 1028952 1539312192
In Profile dropped : 0 0
Out Profile forwarded : 129084 193109664
Out Profile dropped : 0 0
Egress Queue CTL Packets Octets
Forwarded : 16 1024
Dropped : 0 N/A
===============================================================================
See Table: Port Detail Field Descriptions (Ethernet, Access Mode) for field descriptions common to both access and network mode outputs.
Label |
Description |
---|---|
Queue Statistics |
|
Ingress Queue |
For the specified ingress queue, the number of packets and octets that are:
|
Unshaped Egress Queue |
For the specified unshaped egress queue, the of number packets and octets that are:
|
Total Egress from all Shaped and Unshaped Queues |
For all shaped and unshaped queues, the total number of egress packets and octets that are:
|
Egress Queue CTL |
The number of forwarded packets and octets, and the number of dropped packets, for the egress control queue. |
sar18# show port 1/11/1 detail
========================================================================
Ethernet Interface
========================================================================
Description : 10-Gig Bridged Ethernet
Interface : 1/11/1 Oper Speed : 10 Gbps
Link-level : Ethernet Config Speed : N/A
Admin State : up Oper Duplex : full
Oper State : up Config Duplex : N/A
Physical Link : Yes MTU : 9728
Single Fiber Mode : No
IfIndex : 39878656 Hold time up : 0 seconds
Last State Change : 11/03/2012 21:30:51 Hold time down : 0 seconds
Last Cleared Time : N/A DDM Events : Enabled
Configured Mode : network Encap Type : Null&dot1q
Dot1Q Ethertype : 0x8100 VLAN Filter : 2
Ing. Pool % Rate : 100 Egr. Pool % Rate : 100
Net. Egr. Queue Pol: default
Net. Scheduler Mode: 16-priority
Auto-negotiate : N/A MDI/MDX : N/A
Config Phy-tx-clock: not-applicable Oper Phy-tx-clock: N/A
Egress Rate : Default Ingress Rate : Default
Ingress CBS(bytes) : 130816 Src-pause : N/A
LACP Tunnel : N/A
Down-when-looped : N/A Keep-alive : N/A
Loop Detected : N/A Retry : N/A
Use Broadcast Addr : N/A
Loopback : none Swap Mac Addr : Disabled
Loopback Time Left : unspecified
Cfm Loopback : dot1p
Cfm Loopback Vlan : 10-15,20,47
Sync. Status Msg. : Disabled Rx Quality Level : N/A
PTP Asymmetry : N/A Edge Timestamp : Disable
Timestamp Capable : False
Configured Address :
Hardware Address :
Cfg Alarm : remote local
Alarm Status :
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 0 0
Packets 0 0
Errors 0 0
Utilization (30 seconds) 0.00% 0.00%
===============================================================================
===============================================================================
Ethernet Statistics
===============================================================================
Broadcast Pckts : 0 Drop Events : 0
Multicast Pckts : 0 CRC/Align Errors : 0
Undersize Pckts : 0 Fragments : 0
Oversize Pckts : 0 Jabbers : 0
Collisions : 0
Octets : 0
Packets : 0
Packets of 64 Octets : 0
Packets of 65 to 127 Octets : 0
Packets of 128 to 255 Octets : 0
Packets of 256 to 511 Octets : 0
Packets of 512 to 1023 Octets : 0
Packets of 1024 to 1518 Octets : 0
Packets of 1519 or more Octets : 0
===============================================================================
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Unicast Packets 0 0
Multicast Packets 0 0
Broadcast Packets 0 0
Discards 0 0
Unknown Proto Discards 0
===============================================================================
===============================================================================
Ethernet-like Medium Statistics
===============================================================================
Alignment Errors : 0 Sngl Collisions : 0
FCS Errors : 0 Mult Collisions : 0
SQE Test Errors : 0 Late Collisions : 0
CSE : 0 Excess Collisns : 0
Too long Frames : 0 Int MAC Tx Errs : 0
Symbol Errors : 0 Int MAC Rx Errs : 0
In Pause Frames : 0 Out Pause Frames : 0
===============================================================================
===============================================================================
===============================================================================
Ethernet CFM Loopback Statistics N/A
===============================================================================
Queue Statistics
===============================================================================
-------------------------------------------------------------------------------
Egress Queue 1 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
===============================================================================
*A:7705custDoc:Sar18#
Label |
Description |
---|---|
Ethernet Interface |
|
Description |
A text description of the port |
Interface |
The port ID displayed in the slot/mda/port format |
Oper Speed |
The operating speed of the interface |
Link-level |
Ethernet: the port is configured as Ethernet |
Config Speed |
The configured speed of the interface |
Admin State |
up: the port is administratively up |
down: the port is administratively down |
|
Oper Duplex |
The operating duplex mode of the interface |
Oper State |
up: the port is operationally up |
down: the port is operationally down |
|
Config Duplex |
full: the link is configured to full-duplex mode |
half: the link is configured to half-duplex mode |
|
Physical Link |
Yes: a physical link is present |
No: a physical link is not present |
|
MTU |
The size of the largest packet that can be sent/received on the Ethernet physical interface, specified in octets |
Single Fiber Mode |
Yes: single fiber mode |
No: not single fiber mode |
|
IfIndex |
The interface’s index number, which reflects its initialization sequence |
Hold time up |
The link-up dampening time in seconds The port link dampening timer value that reduces the number of link transitions reported to upper layer protocols |
Last State Change |
The last time that the operational status of the port changed state |
Hold time down |
The link-down dampening time in seconds. The down timer controls the dampening timer for link down transitions. |
Last Cleared Time |
The time since the last clear |
DDM Events |
Enabled: digital diagnostic monitoring events is enabled for the port |
Disabled: digital diagnostic monitoring events is disabled for the port |
|
Configured Mode |
network: the port is configured for transport network use |
access: the port is configured for service access |
|
Encap Type |
null: ingress frames will not use any tags or labels to delineate a service |
dot1q: ingress frames carry 802.1Q tags, where each tag signifies a different service |
|
null&dot1q: applies only to port 1 and port 2 on the 2-port 10GigE (Ethernet) Adapter card and 2-port 10GigE (Ethernet) module. The encapsulation type for these ports is not user-configurable. |
|
Dot1Q Ethertype |
The protocol carried in a dot1q Ethernet frame |
VLAN Filter |
The filter ID of the VLAN filter |
Ing. Pool % Rate |
The amount of ingress buffer space, expressed as a percentage of the available buffer space, that will be allocated to the port for ingress buffering |
Egr. Pool % Rate |
The amount of egress buffer space, expressed as a percentage of the available buffer space, that will be allocated to the port for egress buffering |
Net. Egr. Queue Pol. |
The number of the associated network egress queue QoS policy, or default if the default policy is used |
Net. Scheduler Mode |
The mode for servicing CoS queues; 16-priority scheduling is the only supported value |
Auto-negotiate |
true: the link attempts to automatically negotiate the link speed and duplex parameters |
false: the duplex and speed values are used for the link |
|
MDI/MDX |
Ethernet type |
Config Phy-tx-clock |
The mode used to establish timing control of a 1000Base-T port. The options are:
|
Oper Phy-tx-clock |
The operational value of the master-slave relationship of the 1000Base-T physical layer transmit clock. The options are:
|
Egress Rate |
The maximum amount of egress bandwidth (in kilobits per second) that this Ethernet interface can generate |
Ingress Rate |
The maximum amount of ingress bandwidth (in kilobits per second) that this Ethernet interface can generate |
Ingress CBS (bytes) |
Indicates the ingress committed buffer space |
Src-pause |
A notification to slow down the transmission rate when it exceeds the bandwidth limit |
LACP Tunnel |
Indicates whether LACP packet tunneling is enabled |
Down-when-looped |
Enabled: The down-when-looped feature is enabled on the port |
Disabled: The down-when-looped feature is disabled on the port |
|
Keep-alive |
The time interval between keepalive PDUs transmitted toward the network during loop detection by the down-when-looped feature |
Loop Detected |
Indicates whether a loop is detected on the port |
Retry |
The minimum wait time before the port is re-enabled after it is brought down due to a loop detection |
Use Broadcast Addr |
Indicates whether the down-when-looped feature has been configured to compare the destination MAC address of received PDUs to the broadcast MAC address instead of the MAC address of the port |
Loopback |
The type of loopback configured on the port, either line, internal, or none |
Swap Mac Addr. |
Indicates whether MAC address swapping is enabled |
Loopback Time Left |
The number of seconds left in a timed loopback If there is no loopback configured or the configured loopback is latched, the value is unspecified. If configured loopback is persistent, the value persistent |
Cfm Loopback |
Indicates whether the CFM loopback is high priority, low priority, dot1p, or disabled |
Cfm Loopback Vlan |
Indicates the VLAN IDs for VLANs that have a CFM loopback enabled |
Sync. Status Msg. |
Indicates whether Synchronization Status Messaging is enabled on the port |
Rx Quality Level |
The Synchronization Status Messaging quality level value received on the port |
PTP Asymmetry |
Indicates whether PTP asymmetry is enabled |
Edge Timestamp |
Indicates whether the edge timestamp is enabled |
Timestamp Capable |
Indicates whether the port is timestamp-capable |
Code-Type |
The Synchronization Status Messaging quality level code type, either SONET or SDH |
Configured Address |
The base chassis Ethernet MAC address |
Hardware Address |
The interface hardware- or system-assigned MAC address at its protocol sublayer |
Cfg Alarm |
The type of alarms to be logged and reported for the port |
Alarm Status |
The current alarm state |
Traffic Statistics |
|
Octets Input/Output |
The total number of octets received and transmitted on the port |
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Errors Input/Output |
For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol. For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors. |
Utilization Input/Output |
An average computed over the configured interval presented as a percentage of the maximum possible utilization on the Ethernet port. |
Ethernet Statistics |
|
Broadcast Pckts |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a unicast or multicast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a unicast or multicast address at this sublayer, including those that were discarded or not sent. |
Multicast Pckts |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a unicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a unicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Undersize Pckts |
The total number of packets received that were shorter than 64 octets (excluding framing bits, but including FCS octets) but were otherwise well formed |
Oversize Pckts |
The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets) but were otherwise well formed |
Collisions |
The best estimate of the total number of collisions on this Ethernet segment |
Drop Events |
The total number of times that packets were detected as being dropped due to a lack of resources (not necessarily the total number of packets dropped) |
CRC/Align Errors |
The total number of packets received that were between 64 and 1518 octets (excluding framing bits but including FCS octets) that had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error) |
Fragments |
The total number of packets received that were shorter than 64 octets (excluding framing bits but including FCS octets) that had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error) |
Jabbers |
The total number of packets received that were longer than 1518 octets (excluding framing bits but including FCS octets) that had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error) |
Octets |
Total number of octets received |
Packets |
Number of packets received, broken down by size |
Port Statistics |
|
Unicast Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Multicast Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a unicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a unicast or broadcast address at this sublayer, including those that were discarded or not sent |
Broadcast Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a unicast or multicast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a unicast or multicast address at this sublayer, including those that were discarded or not sent. |
Discards Input/Output |
The number of inbound/outbound packets chosen to be discarded to possibly free up buffer space |
Unknown Proto Discards Input/Output |
For packet-oriented interfaces, the number of packets received via the interface that were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing, the number of transmission units received via the interface that were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0. Unknown proto discards do not show up in the packet counts |
Ethernet-like Medium Statistics |
|
Alignment Errors |
The total number of packets received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but that had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets |
FCS Errors |
The number of frames received that are an integral number of octets in length but do not pass the FCS check |
SQE Errors |
The number of times that the SQE TEST ERROR is received |
CSE |
The number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame |
Too long Frames |
The number of frames received that exceed the maximum permitted frame size |
Symbol Errors |
For an interface operating at 100 Mb/s, the number of times there was an invalid data symbol when a valid carrier was present |
In Pause Frames |
The number of IEEE 802.3x pause frames received for flow control; traffic is momentarily disrupted |
Sngl Collisions |
The number of frames that are involved in a single collision, and are subsequently transmitted successfully |
Mult Collisions |
The number of frames that are involved in more than one collision and are subsequently transmitted successfully |
Late Collisions |
The number of times that a collision is detected later than one slotTime into the transmission of a packet |
Excess Collisns |
The number of frames for which a transmission fails due to excessive collisions |
Int MAC Tx Errs |
The number of frames for which a transmission fails due to an internal MAC sublayer transmit error |
Int MAC Rx Errs |
The number of frames for which a reception fails due to an internal MAC sublayer receive error |
Out Pause Frames |
The number of IEEE 802.3x pause frames sent for flow control; traffic is momentarily disrupted |
Ethernet CFM Loopback Statistics N/A |
|
Queue Statistics |
|
Egress Queue |
In Profile forwarded/dropped |
Out Profile forwarded/dropped |
sar18# show port 1/11/v-port detail
========================================================================
Ethernet Interface
========================================================================
Description : 2.5G Virtual Ethernet Port
Interface : 1/11/v-port Oper Speed : 2.50 Gbps
Link-level : Ethernet Config Speed : N/A
Admin State : up Oper Duplex : N/A
Oper State : up Config Duplex : N/A
Physical Link : Yes MTU : 1572
Single Fiber Mode : No
IfIndex : 39944192 Hold time up : N/A
Last State Change : 11/03/2012 21:30:51 Hold time down : N/A
Last Cleared Time : N/A
Configured Mode : network Encap Type : null
Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100
Ing. Pool % Rate : 100 Egr. Pool % Rate : 100
Net. Egr. Queue Pol: r.nw.q4
Net. Scheduler Mode: 16-priority
Auto-negotiate : N/A MDI/MDX : N/A
Config Phy-tx-clock: not-applicable Oper Phy-tx-clock: N/A
Allow Eth-BN : True
BN Egr.Rate in use : 765000 Eth-BN hold time : 6
Egress Rate : Default Ingress Rate : Default
Ingress CBS(bytes) : 130816 Src-pause : Disabled
LACP Tunnel : N/A
Down-when-looped : Disabled Keep-alive : 10
Loop Detected : False Retry : 120
Use Broadcast Addr : False
Loopback : none Swap Mac Addr : Disabled
Loopback Time Left : unspecified
Cfm Loopback : Disabled
Sync. Status Msg. : Disabled Rx Quality Level : N/A
PTP Asymmetry : N/A Edge Timestamp : Disable
Timestamp Capable : False
CRC Mon SD Thresh : Disabled CRC Mon Window : 10 seconds
CRC Mon SF Thresh : Disabled
Configured Address :
Hardware Address :
Cfg Alarm : N/A
Alarm Status : N/A
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 0 0
Packets 0 0
Errors 0 0
Utilization (30 seconds) 0.00% 0.00%
===============================================================================
===============================================================================
Ethernet Statistics
===============================================================================
Broadcast Pckts : 0 Drop Events : 0
Multicast Pckts : 0 CRC/Align Errors : 0
Undersize Pckts : 0 Fragments : 0
Oversize Pckts : 0 Jabbers : 0
Collisions : 0
Octets : 0
Packets : 0
Packets of 64 Octets : 0
Packets of 65 to 127 Octets : 0
Packets of 128 to 255 Octets : 0
Packets of 256 to 511 Octets : 0
Packets of 512 to 1023 Octets : 0
Packets of 1024 to 1518 Octets : 0
Packets of 1519 or more Octets : 0
===============================================================================
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Unicast Packets 0 0
Multicast Packets 0 0
Broadcast Packets 0 0
Discards 0 0
Unknown Proto Discards 0
===============================================================================
===============================================================================
Port Discard Statistics
===============================================================================
Input Output
Inv L2 Packets : 0 Port MTU Exceeded: 0
Inv MPLS Labels : 0
Inv IP Packets : 0
H.Policed Packets: 0
CSM Ingress Queues CSM Egress Queues
Hi : 0 Common : 0
Medium : 0
Low : 0
===============================================================================
===============================================================================
Ethernet-like Medium Statistics
===============================================================================
Alignment Errors : 0 Sngl Collisions : 0
FCS Errors : 0 Mult Collisions : 0
SQE Test Errors : 0 Late Collisions : 0
CSE : 0 Excess Collisns : 0
Too long Frames : 0 Int MAC Tx Errs : 0
Symbol Errors : 0 Int MAC Rx Errs : 0
In Pause Frames : 0 Out Pause Frames : 0
===============================================================================
===============================================================================
Ethernet CFM Statistics
===============================================================================
Cfm LbmRx : 0
Cfm LbReplyTx : 0 Cfm LbmDropped : 0
Num Bn Rate Chng : 1 Last BnRateChng : 04/12/2017 21:20:53
Valid BnmRx : 2 Last Valid BnmRx : 04/12/2017 21:21:10
Invalid BnmRx : 0
BnmOutOfRangeBW : 0
===============================================================================
===============================================================================
Queue Statistics
===============================================================================
-------------------------------------------------------------------------------
Add-drop Port Queue 1 Packets Octets
In Profile forwarded : 8700493441110376715 8700493580567332216
In Profile dropped : 243616594368814244 2209638931652
Out Profile forwarded : 12884901891 8700494542739924144
Out Profile dropped : 143944465151581384 284544364229582056
Ingress Queue 1 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue 9 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Ingress Queue CTL Packets Octets
Forwarded : 0 0
Dropped : 0 N/A
Egress Queue 1 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out Profile forwarded : 0 0
Out Profile dropped : 0 0
Egress Queue CTL Packets Octets
Forwarded : 0 0
Dropped : 0 N/A
===============================================================================
Label |
Description |
---|---|
Ethernet Interface |
|
Description |
A text description of the port |
Interface |
The port ID displayed in the slot/mda/port format |
Oper Speed |
The operating speed of the interface |
Link-level |
Ethernet: the port is configured as Ethernet |
Config Speed |
The configured speed of the interface |
Admin State |
up: the port is administratively up |
down: the port is administratively down |
|
Oper Duplex |
The operating duplex mode of the interface |
Oper State |
up: the port is operationally up |
down: the port is operationally down |
|
Config Duplex |
full: the link is configured to full-duplex mode |
half: the link is configured to half-duplex mode |
|
Physical Link |
Yes: a physical link is present |
No: a physical link is not present |
|
MTU |
The size of the largest packet that can be sent/received on the Ethernet physical interface, specified in octets |
Single Fiber Mode |
Yes: single fiber mode |
No: not single fiber mode |
|
IfIndex |
The interface’s index number, which reflects its initialization sequence |
Hold time up |
The link-up dampening time in seconds The port link dampening timer value that reduces the number of link transitions reported to upper layer protocols |
Last State Change |
The last time that the operational status of the port changed state |
Hold time down |
The link-down dampening time in seconds. The down timer controls the dampening timer for link down transitions. |
Configured Mode |
network: the port is configured for transport network use |
access: the port is configured for service access |
|
Encap Type |
null: ingress frames will not use any tags or labels to delineate a service |
dot1q: ingress frames carry 802.1Q tags, where each tag signifies a different service |
|
null&dot1q: applies only to port 1 and port 2 on the 2-port 10GigE (Ethernet) Adapter card and 2-port 10GigE (Ethernet) module. The encapsulation type for these ports is not user-configurable. |
|
Dot1Q Ethertype |
The protocol carried in a dot1q Ethernet frame |
QinQ Ethertype |
The protocol carried in a QinQ Ethernet frame |
Ing. Pool % Rate |
The amount of ingress buffer space, expressed as a percentage of the available buffer space, that will be allocated to the port for ingress buffering |
Egr. Pool % Rate |
The amount of egress buffer space, expressed as a percentage of the available buffer space, that will be allocated to the port for egress buffering |
Net. Egr. Queue Pol. |
The number of the associated network egress queue QoS policy, or default if the default policy is used |
Auto-negotiate |
true: the link attempts to automatically negotiate the link speed and duplex parameters |
false: the duplex and speed values are used for the link |
|
Net. Scheduler Mode |
The mode for servicing CoS queues; 16-priority scheduling is the only supported value |
MDI/MDX |
Ethernet type |
Config Phy-tx-clock |
The mode used to establish timing control of a 1000Base-T port. The options are:
|
Oper Phy-tx-clock |
The operational value of the master-slave relationship of the 1000Base-T physical layer transmit clock. The options are:
|
Allow Eth-BN |
Indicates whether Ethernet Bandwidth Notification (ETH-BN) is allowed on the port: True or False |
BN Egr.Rate in use |
The egress rate in use based on the request from the ETH-BN server MEP |
Eth-BN hold time |
The configured hold time (in seconds) between an egress rate change based on a received Bandwidth Notification Message (BNM) and the next change request that will be accepted |
Egress Rate |
The maximum amount of egress bandwidth (in kilobits per second) that this Ethernet interface can generate |
Ingress Rate |
The maximum amount of ingress bandwidth (in kilobits per second) that this Ethernet interface can generate |
Ingress CBS (bytes) |
Indicates the ingress committed buffer space |
Src-pause |
A notification to slow down the transmission rate when it exceeds the bandwidth limit |
LACP Tunnel |
Indicates whether LACP packet tunneling is enabled |
Down-when-looped |
Enabled: The down-when-looped feature is enabled on the port |
Disabled: The down-when-looped feature is disabled on the port |
|
Keep-alive |
The time interval between keepalive PDUs transmitted toward the network during loop detection by the down-when-looped feature |
Loop Detected |
Indicates whether a loop is detected on the port |
Retry |
The minimum wait time before the port is re-enabled after it is brought down due to a loop detection |
Use Broadcast Addr |
Indicates whether the down-when-looped feature has been configured to compare the destination MAC address of received PDUs to the broadcast MAC address instead of the MAC address of the port |
Loopback |
The type of loopback configured on the port, either line, internal, or none |
Swap Mac Addr. |
Indicates whether MAC address swapping is enabled |
Loopback Time Left |
The number of seconds left in a timed loopback If there is no loopback configured or the configured loopback is latched, the value is unspecified. If configured loopback is persistent, the value persistent |
Cfm Loopback |
Indicates whether the CFM loopback is high priority, low priority, dot1p, or disabled |
Sync. Status Msg. |
Indicates whether Synchronization Status Messaging is enabled on the port |
Rx Quality Level |
The Synchronization Status Messaging quality level value received on the port |
PTP Asymmetry |
Indicates whether PTP asymmetry is enabled |
Edge Timestamp |
Indicates whether the edge timestamp is enabled |
Timestamp Capable |
Indicates whether the port is timestamp-capable |
CRC Mon SD Thresh |
Indicates the CRC signal degrade threshold value (1 to 9), if enabled |
CRC Mon SF Thresh |
Indicates the CRC signal fail threshold value (1 to 9), if enabled |
CRC Mon Window |
Indicates the CRC window sampling size value (5 to 60) |
Configured Address |
The base chassis Ethernet MAC address |
Hardware Address |
The interface hardware- or system-assigned MAC address at its protocol sublayer |
Cfg Alarm |
The type of alarms to be logged and reported for the port |
Alarm Status |
The current alarm state |
Traffic Statistics |
|
Octets Input/Output |
The total number of octets received and transmitted on the port |
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Errors Input/Output |
For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol. For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors. |
Utilization Input/Output |
An average computed over the configured interval presented as a percentage of the maximum possible utilization on the Ethernet port. |
Ethernet Statistics |
|
Broadcast Pckts |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a unicast or multicast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a unicast or multicast address at this sublayer, including those that were discarded or not sent. |
Multicast Pckts |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a unicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a unicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Undersize Pckts |
The total number of packets received that were shorter than 64 octets (excluding framing bits, but including FCS octets) but were otherwise well formed |
Oversize Pckts |
The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets) but were otherwise well formed |
Collisions |
The best estimate of the total number of collisions on this Ethernet segment |
Drop Events |
The total number of times that packets were detected as being dropped due to a lack of resources (not necessarily the total number of packets dropped) |
CRC/Align Errors |
The total number of packets received that were between 64 and 1518 octets (excluding framing bits but including FCS octets) that had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error) |
Fragments |
The total number of packets received that were shorter than 64 octets (excluding framing bits but including FCS octets) that had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error) |
Jabbers |
The total number of packets received that were longer than 1518 octets (excluding framing bits but including FCS octets) that had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error) |
Octets |
Total number of octets received |
Packets |
Number of packets received |
Packets of n Octets |
Number of packets received, broken down by size |
Port Statistics |
|
Unicast Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Multicast Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a unicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a unicast or broadcast address at this sublayer, including those that were discarded or not sent |
Broadcast Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a unicast or multicast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a unicast or multicast address at this sublayer, including those that were discarded or not sent. |
Discards Input/Output |
The number of inbound/outbound packets chosen to be discarded to possibly free up buffer space |
Unknown Proto Discards Input/Output |
For packet-oriented interfaces, the number of packets received via the interface that were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing, the number of transmission units received via the interface that were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0. Unknown proto discards do not show up in the packet counts |
Port Discard Statistics |
|
Inv L2 Packets Input |
The number of invalid packets that are discarded due to an unknown Layer 2 ID |
Port MTU Exceeded Output |
Indicates that the port MTU has been exceeded |
Inv MPLS Labels Input |
The number of MPLS labels discarded |
Inv IP Packets Input |
The number of invalid IP packets that are discarded |
H. Policed Packets Input |
The number of packets that are discarded due to hard policing |
CSM Ingress Queues Input |
The number of incoming control packets discarded |
CSM Egress Queues Output |
The number of outgoing control packets discarded |
Ethernet-like Medium Statistics |
|
Alignment Errors |
The total number of packets received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but that had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets |
FCS Errors |
The number of frames received that are an integral number of octets in length but do not pass the FCS check |
SQE Errors |
The number of times that the SQE TEST ERROR is received |
CSE |
The number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame |
Too long Frames |
The number of frames received that exceed the maximum permitted frame size |
Symbol Errors |
For an interface operating at 100 Mb/s, the number of times there was an invalid data symbol when a valid carrier was present |
In Pause Frames |
The number of IEEE 802.3x pause frames received for flow control; traffic is momentarily disrupted |
Sngl Collisions |
The number of frames that are involved in a single collision, and are subsequently transmitted successfully |
Mult Collisions |
The number of frames that are involved in more than one collision and are subsequently transmitted successfully |
Late Collisions |
The number of times that a collision is detected later than one slotTime into the transmission of a packet |
Excess Collisns |
The number of frames for which a transmission fails due to excessive collisions |
Int MAC Tx Errs |
The number of frames for which a transmission fails due to an internal MAC sublayer transmit error |
Int MAC Rx Errs |
The number of frames for which a reception fails due to an internal MAC sublayer receive error |
Out Pause Frames |
The number of IEEE 802.3x pause frames sent for flow control; traffic is momentarily disrupted |
Ethernet CFM Statistics |
|
Cfm LbmRx |
The number of LBMs received |
Cfm LbReplyTx |
The number of LBRs transmitted |
Cfm LbmDropped |
The number of LBMs dropped |
Num Bn Rate Chng |
The number of times that the port egress rate is dynamically changed based on Bandwidth Notification (BN) messages Note: not every bandwidth change indicated by a BNM triggers a port egress rate change |
Last BnRateChng |
The time that the port egress rate was last changed based on a BNM |
Valid BnmRx |
The number of valid BN messages received |
Last Valid BnmRx |
The time that the last valid BNM was received |
Invalid BnmRx |
The number of invalid BN messages received |
BnmOutOfRangeBW |
The number of BN messages received with a requested bandwidth that was out of range |
Queue Statistics |
|
Add-drop Port Queue |
In Profile forwarded/dropped |
Out Profile forwarded/dropped |
|
Ingress Queue |
In Profile forwarded/dropped |
Out Profile forwarded/dropped |
|
Ingress Queue CTL |
The number of forwarded packets and octets, and the number of dropped packets, for the ingress control queue. For access ports, this statistic applies only to Ethernet cards. For network ports, this statistic applies to all adapter cards. |
Egress Queue |
In Profile forwarded/dropped |
Out Profile forwarded/dropped |
|
Egress Queue CTL |
The number of forwarded packets and octets, and the number of dropped packets, for the egress control queue. For access ports, this statistic applies only to Ethernet cards. For network ports, this statistic applies to all adapter cards. |
*A:7705:Dut-C>config>port# show port 1/3/25.ds1 detail
===============================================================================
TDM DS1 Interface
===============================================================================
Description : DS1
Interface : 1/3/25.ds1
Type : ds1 Framing : esf
Admin Status : up Oper Status : up
Physical Link : yes Clock Source : node-timed
Signal Mode : none
Last State Change : 03/04/2022 15:34:41 Channel IfIndex : 577536025
Loopback : none Invert Data : false
Remote Loop respond: false In Remote Loop : false
Load-balance-algo : Default Egr. Sched. Pol : N/A
Cfg Alarm : ais los
Alarm Status :
BER SD Threshold : N/A BER SF Threshold : N/A
Hold time up : 0 milliseconds
Hold time down : 0 milliseconds
Sync. Status Msg. : Enabled Tx DUS/DNU : Disabled
Rx Quality Level : 0x04(stu) Tx Quality Level : 0x08(st3)
===============================================================================
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 0 0
Packets 0 0
Errors 0 0
============================
DS1/E1 Line
============================
----------------------------
ES 0
SES 0
SEFS 0
UAS 0
CSS 0
PCV 0
LES 0
BES 0
LCV : 0
==========================
Transmit:
FE-LOF : 0
AIS : 0
Receive:
FE-LOF : 0
AIS : 0
LOS : 0
LOF : 0
Looped : 0
==========================
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 0 0
Discards 0 0
Unknown Proto Discards 0
===============================================================================
Output Example (E1)
*A:ALU-1>config# show port 1/3/1.e1 detail
===============================================================================
TDM E1 Interface
===============================================================================
Description : E1
Interface : 1/3/1.e1
Type : e1 Framing : g704
Admin Status : down Oper Status : down
Physical Link : no Clock Source : node-timed
Clock Sync State : normal
Signal Mode : cas
Last State Change : 10/30/2008 14:40:26 Channel IfIndex : 576749569
Loopback : none
Remote Loop respond: N/A In Remote Loop : N/A
Load-balance-algo : default Egr. Sched. Pol : N/A
Cfg Alarm : ais los ber-sd ber sf
Alarm Status :
BER SD Threshold : 10 BER SF Threshold: 10
Hold time up : 0 milliseconds
Hold time down : 0 milliseconds
Sync. Status Msg. : Enabled Tx DUS/DNU : Disabled
Ssm-bit : 6
Rx Quality Level : 0x02(prc) Tx Quality Level : 0x02(prc)
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 0 0
Packets 0 0
Errors 0 0
===========================
DS1/E1 Line
===========================
---------------------------
ES 0
SES 0
SEFS 0
UAS 0
CSS 0
PCV 0
LES 0
BES 0
LCV : 0
=========================
Transmit:
FE-LOF : 0
AIS : 0
Receive:
FE-LOF : 0
AIS : 0
LOS : 0
LOF : 0
Looped : 0
=========================
===============================================================================
DS1/E1 CAS Signalling Bits
===============================================================================
Rx Tx Rx Tx
Timeslot ABCD ABCD Timeslot ABCD ABCD
-------------------------------------------------------------------------------
1 n/a n/a 13 n/a n/a
2 n/a n/a 14 n/a n/a
3 n/a n/a 15 n/a n/a
4 n/a n/a 16 n/a n/a
5 n/a n/a 17 n/a n/a
6 n/a n/a 18 n/a n/a
7 n/a n/a 19 n/a n/a
8 n/a n/a 20 n/a n/a
9 n/a n/a 21 n/a n/a
10 n/a n/a 22 n/a n/a
11 n/a n/a 23 n/a n/a
12 n/a n/a 24 n/a n/a
===============================================================================
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 0 0
Discards 0 0
Unknown Proto Discards 0
===============================================================================
Label |
Description |
---|---|
TDM DS1/E1 Interface |
|
Description |
A text description of the port |
Interface |
The port ID displayed in the slot/mda/port format |
Type |
The type of interface |
Framing |
The DS1/E1 framing to be used for the port If SSM is enabled, framing is always esf for DS1 and g704 for E1 |
Admin Status |
up: the port is administratively up |
down: the port is administratively down |
|
Oper Status |
up: the port is operationally up |
down: the port is operationally down |
|
Physical Link |
yes: a physical link is present |
no: a physical link is not present |
|
Clock Source |
loop-timed: the link recovers the clock from the received data stream node-timed: the link uses the internal clock when transmitting data adaptive: clocking is derived from the incoming pseudowire packets differential: clocking is derived from a common clock compared to differential clock recovery data in the RTP header in the TDM PW overhead |
Signal Mode |
The port signaling mode |
Last State Change |
The last time that the operational status of the port changed state |
Channel IfIndex |
The channel interface index number |
Loopback |
The port loopback mode |
Remote Loop respond |
The DS1/E1 channel response to remote loopbacks |
In Remote Loop |
Indicates whether incoming remote loopback is enabled |
Load-balance-algo |
The load balance algorithm used on the port |
Egr. Sched. Pol |
The egress scheduling policy |
Cfg Alarm |
The type of alarms to be logged and reported for the port |
Alarm Status |
The current alarm state |
BER SD Threshold |
The configured value of the BER SD threshold |
BER SF Threshold |
The configured value of the BER SF threshold |
Hold time up |
The hold-timer value for link-up event dampening |
Hold time down |
The hold-timer value for link-down event dampening |
Sync. Status Msg. |
The setting of SSM: enabled or disabled |
Tx DUS/DNU |
The setting of tx-dus: enabled or disabled |
Ssm-bit |
The Sa bit that carries the quality level value on E1 interfaces: Sa4 to Sa8 |
Rx Quality Level |
The SSM QL value received on the interface |
Tx Quality Level |
The SSM QL value transmitted on the interface |
Clock Sync State |
The current state of the clock recovery function |
Traffic Statistics |
|
Octets Input/Output |
The total number of octets received and transmitted on the port |
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Errors Input/Output |
For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol. For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors. |
DS1/E1 Line |
The DS1/E1 Line statistics |
ES |
The number of Errored Seconds errors |
SES |
The number of Severely Errored Seconds errors |
SEFS |
The number of Severely Errored Framing Seconds errors |
UAS |
The number of Unavailable Seconds errors |
CSS |
The number of Controlled Slip Seconds errors |
PCV |
The number of Path Code Violations errors |
LES |
The number of Line Errored Seconds errors |
BES |
The number of Bursty Errored Seconds alarms |
LCV |
The number of Line Code Violations errors |
Transmit |
The transmit statistics: FE-LOF: the number of far-end loss of frame errors AIS: the number of alarm indication signal errors |
Receive |
The receive statistics: FE-LOF: the number of far-end loss of frame errors AIS: the number of alarm indication signal errors LOS: the number of loss of signal errors LOF: the number of loss of frame errors |
Looped |
The number of looped packet errors |
DS1/E1 CAS Signalling Bits |
The CAS signaling bit information |
Timeslot |
The timeslot number (1 to 24 for DS1, 2 to 32 for E1) |
Rx ABCD |
The signaling bits received in the timeslot, where each signaling bit is represented by a 1 (set) or a 0 (not set), and 0000 represents a timeslot that is in use but not receiving any signaling bits (for example, 1000 means that the A bit is set); ‟n/a” indicates timeslots not in use |
Tx ABCD |
The signaling bits transmitted from the timeslot, where each signaling bit is represented by a 1 (set) or a 0 (not set), and 0000 represents a timeslot that is in use but not transmitting any signaling bits (for example, 1000 means that the A bit is set); ‟n/a” indicates timeslots not in use |
Port Statistics |
|
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a unicast, multicast, or broadcast address at this sublayer |
Discards Input/Output |
The number of inbound/outbound packets chosen to be discarded to possibly free up buffer space |
Unknown Proto Discards Input/Output |
For packet-oriented interfaces, the number of packets received via the interface that were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing, the number of transmission units received via the interface that were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0. Unknown proto discards do not show up in the packet counts. |
*A:ALU-1># show port 1/2/1.v35
===============================================================================
Serial RS-232 Interface
===============================================================================
Description : V35
Interface : 1/2/1.v35
Type : v35
Admin Status : up Oper Status : up
Physical Link : yes Clock Source : slave
Device Mode : synchronous Speed : 64k
Character Length : N/A Parity : N/A
Stop Bits : N/A
Device Gender : dte Duplex : full
Last State Change : 02/13/2015 21:03:47 Channel IfIndex : 574652417
Loopback : none
Hold time up : 0 milliseconds
Hold time down : 0 milliseconds
Cfg Alarm :
Alarm Status :
===============================================================================
=============================================
Serial Control Leads
=============================================
Inputs Cfg Netw Line Mon
---------------------------------------------
dtr-dsr [DSR] : high 1 1 off
rts-dcd [DCD] : high 1 0 off
alb-cts [CTS] : high 1 1 off
Outputs Cfg Netw Line
---------------------------------------------
dsr-dtr [DTR] : high 1 1
dcd-rts [RTS] : high 1 1
cts-alb [ALB] : high 1 1
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 39022208 39022016
Packets 609722 609719
Errors 0 0
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 609722 609719
Discards 0 0
Unknown Proto Discards 0
===============================================================================
*A:ALU-1># show port 1/2/7.x21
===============================================================================
Serial RS-232 Interface
===============================================================================
Description : X21
Interface : 1/2/7.x21
Type : x21
Admin Status : up Oper Status : up
Physical Link : yes Clock Source : slave
Device Mode : synchronous Speed : 64k
Character Length : N/A Parity : N/A
Stop Bits : N/A
Device Gender : dte Duplex : full
Data Position : N/A S-Bit Signaling : N/A
Last State Change : 02/13/2015 21:03:50 Channel IfIndex : 574849031
Loopback : none
Hold time up : 0 milliseconds
Hold time down : 0 milliseconds
Cfg Alarm :
Alarm Status :
===============================================================================
=============================================
Serial Control Leads
=============================================
Inputs Cfg Netw Line Mon
---------------------------------------------
c-i [I] : high 1 1 off
Outputs Cfg Netw Line
---------------------------------------------
i-c [C] : high 1 1
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 39403456 39403264
Packets 615679 615676
Errors 0 0
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 615679 615676
Discards 0 0
Unknown Proto Discards 0
===============================================================================
*A:ALU-1># show port 1/2/4.rs232
===============================================================================
Serial RS-232 Interface
===============================================================================
Description : RS232
Interface : 1/2/4.rs232
Type : rs232
Admin Status : up Oper Status : up
Physical Link : yes Clock Source : slave
Device Mode : synchronous Speed : 9600
Character Length : N/A Parity : N/A
Stop Bits : N/A Multi-Drop : disabled
Device Gender : dce Duplex : full
Data Position : F0-B5 S-Bit Signaling : on
Last State Change : 02/13/2015 21:04:16 Channel IfIndex : 574750724
Loopback : none
Hold time up : 0 milliseconds
Hold time down : 0 milliseconds
Cfg Alarm : hcmOof hcmRai
Alarm Status :
===============================================================================
=============================================
Serial Control Leads
=============================================
Inputs Cfg Netw Line Mon
---------------------------------------------
dtr-dsr [DTR] : high 1 1 off
rts-dcd [RTS] : high 1 1 off
alb-cts [ALB] : high 1 0 off
rdl-ri [RDL] : high 1 0 off
Outputs Cfg Netw Line
---------------------------------------------
dsr-dtr [DSR] : high 1 1
dcd-rts [DCD] : high 1 1
cts-alb [CTS] : high 1 1
ri-rdl [RI] : high 1 1
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 17935808 17932416
Packets 280247 280194
Errors 0 0
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 280247 280194
Discards 0 0
Unknown Proto Discards 0
===============================================================================
The following output is an example of raw socket statistics.
*A:ALU-1># show port 1/12/6.1
===============================================================================
Serial Socket
===============================================================================
Description : SOCKET
Interface : 1/12/6.1
Admin Status : up Oper Status : up
Last State Change : 01/24/2017 15:21:05 Socket IfIndex : 595787809
Configured mode : access Encap Type : raw
Physical Link : yes
EOP Length : 511 Squelch Delay : Disabled
EOP Idle Timeout : 5000 Unsquelch Delay : Disabled
EOP Special Char : Disabled Inter-Session Delay : 10
Squelch Status : off
===============================================================================
=============================================================
Socket Statistics
=============================================================
Count
-------------------------------------------------------------
Characters received 4088
Characters transmitted 4088
End of packet idle timeout 0
End of packet length 8
End of packet special character 0
Ingress forwarded packets 8
Egress forwarded packets 8
Ingress dropped packets 0
Egress dropped packets 0
Squelch activated 0
=============================================================
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 4088 4088
Packets 8 8
Errors 0 0
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 8 8
Discards 0 0
Unknown Proto Discards 0
===============================================================================
Label |
Description |
---|---|
Serial RS-232 Interface |
|
Description |
The description of the port |
Interface |
The port ID displayed in the slot/mda/port.channel format |
Type |
The type of serial interface |
Admin Status |
up: the administrative state is up down: the administrative state is down |
Oper Status |
up: the operational state is up down: the operational state is down |
Physical Link |
yes: a physical link is present no: a physical link is not present |
Clock Source |
The source of the transmit clock: On the 12-port Serial Data Interface card, version 2: slave On the 12-port Serial Data Interface card, version 3:
|
Device Mode |
The operational mode of the device, either synchronous (the device transmits data continuously based on timing) or asynchronous (the device transmits data one character at a time) Asynchronous mode is supported only on channels with subrate speeds of 38 400 b/s or less RS-232, RS-530, and X.21 channels support synchronous and asynchronous modes (RS-530 channels are only supported on the 12-port Serial Data Interface card, version 3) V.35 channels support synchronous mode only |
Speed |
The speed of the interface |
Character Length |
The number of data bits used to transmit a character; for asynchronous devices only |
Parity |
The parity bit in a character; for asynchronous devices only |
Stop Bits |
The number of stop bits used signify the end of a character; for asynchronous devices only |
Multi-Drop |
The MDDB mode; supported on RS-232 and X.21 synchronous or asynchronous links, and on RS-530 asynchronous links (RS-530 links are only supported on the 12-port Serial Data Interface card, version 3): disabled: MDDB mode is off slave: device operates as an MDDB slave device master: device operates as an MDDB master device |
Device Gender |
The gender of the device: dce: the device is performing the role of the data communications equipment dte: the device is performing the role of the data terminal equipment |
Duplex |
The duplex mode: half: single transmission path (supported only if multidrop data bridge is enabled in slave mode) full: two independent transmission paths, one in each direction |
Data Position |
The HCM data start position; applies to RS-232, RS-530, and X.21 interfaces only (RS-530 interfaces are only supported on the 12-port Serial Data Interface card, version 3) |
S-Bit-Signaling |
Indicates whether S-bit signaling is turned on or off; applies to RS-232, RS-530, and X.21 interfaces only (RS-530 interfaces are only supported on the 12-port Serial Data Interface card, version 3) |
Last State Change |
The last time the operational status of the port changed state |
Channel IfIndex |
The channel group index number |
Loopback |
The loopback mode for the port or channel: bidir-b: bidirectional loopback B takes place on the control card (CSM) side of the adapter card and is closer to the system (not supported on the 12-port Serial Data Interface card, version 3) bidir-e: bidirectional loopback E takes place on the data device side of the adapter card and is closer to the line none: there is no loopback done at the associated port or channel |
Hold time up |
The hold-timer value for link-up event dampening |
Hold time down |
The hold-timer value for link-down event dampening |
Cfg Alarm |
The HCM alarms to be reported for RS-232, RS-530, or X.21 interfaces (RS-530 interfaces are only supported on the 12-port Serial Data Interface card, version 3): hcmOof: local HCM out-of-frame errors are raised and cleared hcmRai: HCM remote alarm indication events are raised and cleared |
Alarm Status |
The current alarm status |
Serial Control Leads (the input and output leads, which carry control signals) |
|
Inputs |
The input control leads |
dtr-dsr |
The Data Terminal Ready/Data Set Ready input control lead (applicable only for RS-232, RS-530, and V.35 interfaces; RS-530 interfaces are only supported on the 12-port Serial Data Interface card, version 3) |
rts-dcd |
The Request To Send/Data Carrier Detect input control lead (applicable only for RS-232, RS-530, and V.35 interfaces; RS-530 interfaces are only supported on the 12-port Serial Data Interface card, version 3) |
ll-tm |
The Local Loopback/Test Mode input control lead (only supported on RS-530 interfaces on the 12-port Serial Data Interface card, version 3) |
rl-cts |
The Remote Loopback/Clear To Send input control lead (only supported on RS-530 interfaces on the 12-port Serial Data Interface card, version 3) |
alb-cts |
The Analog Loopback/Clear To Send input control lead (applicable only for RS-232 and V.35 interfaces) Not supported on the 4-port T1/E1 and RS-232 Combination module |
rdl-ri |
The Remote Digital Loopback/Ring Indicator input control lead (applicable only for RS-232 interfaces) Not supported on the 4-port T1/E1 and RS-232 Combination module |
c-i |
The Control/Indication input control lead (applicable only for X.21 interfaces) |
Cfg |
The configuration of the input signaling leads:
|
Outputs |
The output control leads |
dsr-dtr |
The Data Set Ready/Data Terminal Ready output control lead (applicable only for RS-232, RS-530, and V.35 interfaces; RS-530 interfaces are only supported on the 12-port Serial Data Interface card, version 3) Not supported on the 4-port T1/E1 and RS-232 Combination module |
dcd-rts |
The Data Carrier Detect/Request To Send output control lead (applicable only for RS-232, RS-530, and V.35 interfaces; RS-530 interfaces are only supported on the 12-port Serial Data Interface card, version 3) |
cts-alb |
The Clear To Send/Analog Loopback output control lead (applicable only for RS-232 and V.35 interfaces) |
ri-rdl |
The Ring Indicator/Remote Digital Loopback output control lead (applicable only for RS-232 interfaces) |
cts-rl |
The Clear To Send/Remote Loopback output control lead (only supported on RS-530 interfaces on the 12-port Serial Data Interface card, version 3) |
tm-ll |
The Test Mode/Local Loopback output control lead (only supported on RS-530 interfaces on the 12-port Serial Data Interface card, version 3) |
i-c |
The Indication/Control output control lead (applicable only for X.21 interfaces) |
Cfg |
The configuration of the output signaling leads:
|
Netw |
The value that indicates the current states of the input and output control leads. These values are transported over the network; therefore, are referred to as network-side values:
|
Line |
The value that indicates the current signal levels of the input and output control leads connected to the attached CPE. These values are signaled over the (physical) line; therefore, are referred to as line-side values:
|
Mon |
Indicates whether monitoring is enabled (on) or disabled (off) for the control lead; applies to input control leads only |
Traffic Statistics |
|
Octets Input/Output |
The total number of octets received and transmitted on the port |
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Errors Input/Output |
For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol. For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors. |
Port Statistics |
|
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Discards Input/Output |
The number of inbound/outbound packets chosen to be discarded to possibly free up buffer space |
Unknown Proto Discards Input/Output |
For packet-oriented interfaces, the number of packets received at the interface that were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing, the number of transmission units received at the interface that were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0. |
Serial Socket |
|
Description |
The configured port type |
Interface |
The interface ID displayed in the format slot/mda/port.channel |
Admin Status |
The administrative status of the port, either up or down |
Oper status |
The operational status of the port, either up or down |
Last State Change |
The last time the operational status of the channel changed state |
Socket IfIndex |
The socket index number |
Configured mode |
The port mode (serial raw sockets support access mode only) |
Encap Type |
The encapsulation type of the port (serial raw sockets support encapsulation type raw only) |
Physical Link |
Indicates whether a physical link is present |
EOP Length |
The number of characters (in bytes) that trigger sending an IP transport packet when end of packet is declared |
Squelch Delay |
Indicates whether squelch delay is enabled or disabled |
EOP Idle Timeout |
The limit, in milliseconds, that a queued packet can remain idle before an end of packet is declare |
Unsquelch Delay |
Indicates whether unsquelch delay is enabled or disabled |
EOP Special Char |
Indicates whether the sending of a special character that declares end of packet is enabled or disabled |
Inter-Session Delay |
The time delay, in milliseconds, between transmission of a session’s data over a serial port and the transmission of the next queued session’s data |
Squelch Status |
Indicates whether squelch is enabled (on) or disabled (off) |
Socket Statistics |
|
Characters received |
The number of data characters received |
Characters transmitted |
The number of data characters sent |
End of packet idle timeout |
The number of times that end of packet has been declared due to an EOP idle timeout |
End of packet length |
The number of times that an IP transport packet was sent due to the EOP packet length being exceeded |
End of packet special character |
The number of times that end of packet has been declared due to an EOP special character being sent |
Ingress forwarded packets |
The number of ingress forwarded packets |
Egress forwarded packets |
The number of egress forwarded packets |
Ingress dropped packets |
The number of ingress dropped packets |
Egress dropped packets |
The number of egress dropped packets |
Squelch activated |
The number of times that squelch was activated |
*A:ALU-1># show port 1/1/1.em detail
===============================================================================
Voice Interface
===============================================================================
Description : EM
Interface : 1/1/1.em
Type : em
Admin Status : up Oper Status : up
Physical Link : yes Clock Source : node-timed
Signaling Mode : em Signal Mode : cas
Fault Signaling : idle
Idle Code : 13 (0b1101) Seized Code : 5 (0b0101)
Last State Change : 01/08/2010 14:23:28 Channel IfIndex : 578846721
Loopback : none
===============================================================================
===============================================================================
Voice E&M Signaling Leads
===============================================================================
Inputs Cfg Scans Outputs Cfg Drives
-------------------------------------------------------------------------------
m : end-to-end 0 e : end-to-end 0
===============================================================================
===============================================================================
Voice Signalling Bits
===============================================================================
Rx Tx
DS0 ABCD ABCD
-------------------------------------------------------------------------------
1 1101 1101
===============================================================================
===================================================
Voice Call Usage Statistics (state: idle)
===================================================
Accumulated
---------------------------------------------------
I/C Call Count 0
I/C Call Count, Ans 0
I/C Call Time 0
I/C Call Time, Ans 0
O/G Call Count 0
O/G Call Count, Ans 0
O/G Call Time 0
O/G Call Time, Ans 0
Out Of Service Time 10
Idle Time 39
Total Call Count 0
Total Call Time 0
===================================================
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 388432 388256
Packets 24277 24266
Errors 0 0
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 30868 30857
Discards 0 0
Unknown Proto Discards 0
===============================================================================
Label |
Description |
---|---|
Voice Interface |
|
Description |
The description of the port |
Interface |
The port ID displayed in the slot/mda/port.channel format |
Type |
The type of voice interface |
Admin Status |
up: the administrative state is up |
down: the administrative state is down |
|
Oper Status |
up: the operational state is up |
down: the operational state is down |
|
Physical Link |
yes: a physical link is present |
no: a physical link is not present |
|
Clock Source |
node-timed: the link uses the internal clock when transmitting data |
Signaling Mode |
The signaling mode used by the interface, either em or transmission-only |
Signal Mode |
The network signaling transport scheme, either cas for em signaling or none for transmission-only signaling |
Fault Signaling |
The type of fault signaling used by the channel, either idle or seized |
Idle Code |
The ABCD signaling code to be transmitted when the channel is configured to transmit idle fault signaling |
Seized Code |
The ABCD signaling code to be transmitted when the channel is configured to transmit seized fault signaling |
Last State Change |
The last time the operational status of the channel changed state |
Channel IfIndex |
The channel index number |
Loopback |
The loopback mode for the channel: internal-analog, internal-digital, or none |
Voice E&M Signaling Leads |
|
Inputs |
The type of input signaling lead (M-lead), shown only if the signaling mode is E&M |
Cfg |
The configuration of the input signaling lead: |
high: (the input signaling lead is assumed on) |
|
low: (the input signaling lead is assumed off) |
|
end-to-end: (the input signaling lead follows that of the remote end) |
|
Scans |
The current scanned value of the input lead, which can either be 0 (idle) or 1 (seized) |
Outputs |
The type of output lead (E-lead), shown only if the signaling mode is E&M |
Cfg |
The configuration of the output signaling lead: |
high: (the output signaling lead is forced on) |
|
low: (the output signaling lead is forced off) |
|
end-to-end: (the output signaling lead follows that of the remote end) |
|
Drives |
The current value set on the output lead, which can either be 0 (idle) or 1 (seized) |
Voice Signalling Bits |
|
DS0 |
The number of DS0 voice signaling bits |
Rx ABCD |
The signaling bits received from the network side |
Tx ABCD |
The signaling bits transmitted to the network side |
Voice Call Usage Statistics |
|
State |
The state of the channel (non-forwarding, out-of-service, idle, incoming, or outgoing), and voice call usage statistics. Non-forwarding means that the channel is inshutdown mode or has no SAP configured; incoming means that the call was received by the channel; outgoing means that the call was originated by the channel |
Accumulated |
The total accumulated statistics since the last time the statistics were cleared |
I/C Call Count |
The number of incoming calls |
I/C Call Count, Ans |
The number of incoming calls that were answered |
I/C Call Time |
The total duration (in seconds) of all incoming calls |
I/C Call Time, Ans |
The total duration (in seconds) of all incoming calls that were answered |
O/G Call Count |
The number of outgoing calls |
O/G Call Count, Ans |
The number of outgoing calls that were answered |
O/G Call Time |
The total duration (in seconds) of all outgoing calls |
O/G Call Time, Ans |
The total duration (in seconds) of all outgoing calls that were answered |
Out-Of-Service Time |
The time (in seconds) for which the circuit had alarms raised against the service. The only valid statistics for transmission-only mode are Out-Of-Service Time and Idle Time. |
Idle Time |
The total duration the circuit was in an idle state (that is, on-hook). The only valid statistics for transmission-only mode are Out-Of-Service Time and Idle Time. When the system is in transmission-only mode and in a forwarding state, there is no signaling. To show that the system is active (that is, not in an out-of-service state), the ‟Idle Time” counter is incremented. This is a design intent. |
Total Call Count |
The sum of I/C Call Count and O/G Call Count |
Total Call Time |
The sum of I/C Call Time and O/G Call Time |
Traffic Statistics |
|
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Errors Input/Output |
For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol. For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors. |
Port Statistics |
|
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Discards Input/Output |
The number of inbound/outbound packets chosen to be discarded to possibly free up buffer space |
Unknown Proto Discards Input/Output |
For packet-oriented interfaces, the number of packets received at the interface that were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing, the number of transmission units received at the interface that were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0. |
*A:ALU-1># show port 1/4/1.5
===============================================================================
TDM DS0 Chan Group
===============================================================================
Description : DS0GRP
Interface : 1/4/1.5
TimeSlots :
Speed : 64 CRC : 16
Admin Status : down Oper Status : down
BER SF Link Down : disabled
Last State Change : 06/22/2009 12:29:42 Chan-Grp IfIndex : 578846785
Loopback : line
Configured mode : access Encap Type : atm
Admin MTU : 1524 Oper MTU : 1524
Scramble : true
Physical Link : Yes Bundle Number : none
Idle Cycle Flags : n/a Load-balance-algo : n/a
Payload Fill Type : n/a Payload Pattern : n/a
Signal Fill Type : n/a Signal Pattern : n/a
Ing. Pool % Rate : 100 Egr. Pool % Rate : 100
Egr. Sched. Pol : n/a
===============================================================================
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 0 0
Packets 0 0
Errors 0 0
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 0 0
Discards 0 0
Unknown Proto Discards 0
===============================================================================
*A:ALU-1#
*A:ALU-1># show port 1/1/2.1
===============================================================================
Serial DS0 Chan Group
===============================================================================
Description : DS0GRP
Interface : 1/1/2.1
TimeSlots : 1
Admin Status : down Oper Status : down
Last State Change : 06/28/2009 15:32:14 Chan-Grp IfIndex : 572588095
Configured Mode : access Encap Type : cem
Admin MTU : 1514 Oper MTU : 1514
Physical Link : No Bundle Number : none
Idle Cycle Flags : n/a
Payload Fill Type : all-ones Payload Pattern : n/a
===============================================================================
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 0 0
Packets 0 0
Errors 0 0
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 0 0
Discards 0 0
Unknown Proto Discards 0
===============================================================================
*A:ALU-1#
*A:ALU-1># show port 1/1/1.1
===============================================================================
Voice DS0 Chan Group
===============================================================================
Description : DS0GRP
Interface : 1/1/1.1
Admin Status : up Oper Status : up
Last State Change : 01/08/2010 14:23:29 Chan-Grp IfIndex : 578846781
Configured Mode : access Encap Type : cem
Admin MTU : 1514 Oper MTU : 1514
Physical Link : Yes
===============================================================================
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 611744 611584
Packets 38234 38224
Errors 0 0
===============================================================================
Port Statistics
==============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 38234 38224
Discards 0 0
Unknown Proto Discards 0
===============================================================================
*A:ALU-1#
A:ALU-1# show port 1/2/2.1.1
===============================================================================
TDM DS1 Interface
===============================================================================
Description : DS1
Interface : 1/2/2.1.1
Type : ds1 Framing : esf
Admin Status : up Oper Status : down
Physical Link : no Clock Source : node-timed
Last State Change : 01/26/2009 15:35:50 Channel IfIndex : 574685991
Loopback : none
Remote Loop respond: false In Remote Loop : false
Load-balance-algo : default Egr. Sched. Pol : N/A
Cfg Alarm : ais los
Alarm Status :
Hold time up : 0 milliseconds
Hold time down : 0 milliseconds
===============================================================================
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 0 0
Packets 0 0
Errors 0 0
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 0 0
Discards 0 0
Unknown Proto Discards 0
===============================================================================
Label |
Description |
---|---|
Description |
A text description of the port |
Interface |
The port ID displayed in the format slot/mda/port.channel-group-id |
Timeslots |
The number of timeslots that are part of this channel group |
Speed |
The speed of the interface |
CRC |
The checksum used for the channel group (16 or 32) |
Admin Status |
Up: the port is administratively up |
Down: the port is administratively down |
|
BER SF Link Down |
Indicates whether BER SF Link Down is enabled |
Oper Status |
Up: the port is operationally up |
Down: the port is operationally down |
|
Remote Loop respond |
Indicates whether the channel will respond to requests for remote loopbacks |
Cfg Alarm |
Indicates the alarms configured |
Last State Change |
The last time the operational status of the port changed state |
Chan Grp IfIndex |
The channel group index number |
Channel IfIndex |
The channel interface index number |
Loopback |
The type of loopback configured on the channel group: line, internal, or none |
Configured Mode |
network: the port is configured for transport network use |
access: the port is configured for service access |
|
Encap Type |
The encapsulation type for the channel group (atm, cem, ipcp, ppp-auto, hdlc, or cisco-hdlc) |
Admin MTU |
The configured MTU |
Oper MTU |
The negotiated size of the largest packet that can be sent on the port or channel specified in octets |
Scramble |
Indicates whether payload scrambling is enabled on channel groups (only applicable if encap type is atm) |
Hold time up |
The hold-timer value for link-up event dampening |
Hold time down |
The hold-timer value for link-down event dampening |
Physical Link |
Yes: a physical link is present |
No: a physical link is not present |
|
Bundle Number |
The number assigned to the multilink bundle |
Idle Cycle Flags |
The value transmitted by the DS0, DS1, or E1 interface during idle cycles |
Clock Source |
loop-timed: the link recovers the clock from the received data stream node-timed: the link uses the internal clock when transmitting data adaptive: clocking is derived from the incoming pseudowire packets |
Payload Fill Type |
The payload type to be transmitted when the circuit emulation service is not operational or temporarily experiences underrun conditions (only valid for CESoPSN services) |
Payload Pattern |
The user-defined pattern transmitted if the payload fill type is pattern |
Signal Fill Type |
The signaling type to be transmitted when the circuit emulation service is not operational or temporarily experiences underrun conditions (only valid for CESoPSN with CAS) |
Signal Pattern |
The user-defined pattern transmitted if the payload fill type is pattern |
Traffic Statistics |
|
Octets Input/Output |
The total number of octets received and transmitted on the port |
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Errors Input/Output |
For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol. For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors. |
Port Statistics |
|
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Discards Input/Output |
The number of inbound/outbound packets chosen to be discarded to possibly free up buffer space |
Unknown proto discards Input/Output |
For packet-oriented interfaces, the number of packets received via the interface that were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing, the number of transmission units received via the interface that were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0. For ATM, this field displays cells discarded on an invalid vpi/vci. Unknown proto discards do not show up in the packet counts. |
A:ALU-1# show port 1/4/1.ds3
===============================================================================
TDM Interface
===============================================================================
Description : DS3
Interface : 1/4/1.ds3
Type : ds3 Framing : m23
Admin Status : up Oper Status : up
Physical Link : No Clock Source : node-timed
Last State Change : 10/02/2009 19:21:59 Port IfIndex : 578846721
Configured mode : access Encap Type : atm
Admin MTU : 1524 Oper MTU : 1524
Scramble : true
Ing. Pool % Rate : 100 Egr. Pool % Rate : 100
Egr. Sched. Pol : N/A
CRC : 32 Channelized : DS1
Idle Cycle Flags : n/a Loopback : line
FEAC Loop Respond : Disabled In FEAC Loop : No
BERT Duration : N/A BERT Pattern : none
BERT Synched : 00h00m00s Err Insertion Rate : 0
BERT Errors : 0 BERT Status : idle
BERT Total Bits : N/A
Cfg Alarm : ais los
Alarm Status :
Subrate CSU Mode : none Subrate Step : 0
MDL Transmit : none
-------------------------------------------------------------------------------
Local MDL Information
-------------------------------------------------------------------------------
EIC : LIC :
FIC : Unit :
PFI :
Idle Signal Port :
Test Signal Gen :
-------------------------------------------------------------------------------
Far End MDL Information
-------------------------------------------------------------------------------
EIC : LIC :
FIC : Unit :
PFI :
Idle Signal Port :
Test Signal Gen :
===============================================================================
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 0 0
Packets 0 0
Errors 0 0
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 0 0
Discards 0 0
Unknown Proto Discards 0
===============================================================================
Label |
Description |
---|---|
Description |
A text description of the port |
Interface |
The port ID displayed in the format slot/mda/port.channel-group-id |
Type |
The type of interface |
Timeslots |
The number of timeslots that are part of this channel group |
Speed |
The speed of the interface |
CRC |
The checksum used for the channel group (16 or 32) |
Admin Status |
Up: the port is administratively up |
Down: the port is administratively down |
|
Oper Status |
Up: the port is operationally up |
Down: the port is operationally down |
|
Last State Change |
The last time the operational status of the port changed state |
Chan Grp IfIndex |
The channel group index number |
Configured Mode |
network: the port is configured for transport network use |
access: the port is configured for service access |
|
Encap Type |
The encapsulation type for the channel group (atm, cem, ipcp, ppp-auto) |
Admin MTU |
The configured MTU |
Oper MTU |
The negotiated size of the largest packet that can be sent on the port or channel specified in octets |
Scramble |
Indicates whether payload scrambling is enabled on channel groups (only applicable if encap type is atm) |
CRC |
Indicates the precision of the cyclic redundancy check: 16 — a 16-bit CRC calculation 32 — a 32-bit CRC calculation; 32-bit CRC increases the error detection ability, but it also adds some performance overhead |
Physical Link |
Yes: a physical link is present |
No: a physical link is not present |
|
Idle Cycle Flags |
The value transmitted by the DS0, DS1, or E1 interface during idle cycles |
FEAC Loop Respond |
Indicates whether the associated DS3 interface can respond to remote loop signals |
Cfg Alarm |
The alarms that have alarm reporting enabled |
Alarm Status |
The current alarm state (for example, stray, malformed, packet loss, overrun, underrun, remote packet loss, remote fault, or remote RDI) |
Framing |
The DS3 framing mode |
Clock Source |
loop-timed: the link recovers the clock from the received data stream node-timed: the link uses the internal clock when transmitting data adaptive: clocking is derived from the incoming pseudowire packets |
Port IfIndex |
The interface’s index number, which reflects its initialization sequence |
oper MTU |
The negotiated size of the largest packet that can be sent on the port or channel specified in octets |
Channelized |
The level of channelization on the port |
Loopback |
The port loopback mode |
In FEAC Loop |
The remote loopback state |
Local MDL Information |
The MDL strings sent by the near end |
Far End MDL Information |
The MDL strings received from the far end |
Traffic Statistics |
|
Octets Input/Output |
The total number of octets received and transmitted on the port |
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Errors Input/Output |
For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol. For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors. |
Port Statistics |
|
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Discards Input/Output |
The number of inbound/outbound packets chosen to be discarded to possibly free up buffer space |
Unknown proto discards Input/Output |
For packet-oriented interfaces, the number of packets received via the interface that were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing, the number of transmission units received via the interface that were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0. For ATM, this field displays cells discarded on an invalid vpi/vci. Unknown proto discards do not show up in the packet counts. |
A:ALU-1# show port 1/4/1
===============================================================================
TDM DS3 Physical Interface
===============================================================================
Description : DS3/E3
Interface : 1/4/1 Port IfIndex : 41975808
Admin Status : down Oper Status : down
Physical Link : No
Type : ds3 Buildout : short
Hardware Address : 2001:db8::
===============================================================================
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 0 0
Discards 0 0
Unknown Proto Discards 0
===============================================================================
Label |
Description |
---|---|
Description |
A text description of the port |
Interface |
The port ID displayed in the format slot/mda/port |
Port IfIndex |
The interface’s index number, which reflects its initialization sequence |
Admin Status |
Up: the port is administratively up |
Down: the port is administratively down |
|
Oper Status |
Up: the port is operationally up |
Down: the port is operationally down |
|
Physical Link |
Yes: a physical link is present |
No: a physical link is not present |
|
Type |
The type of interface |
Buildout |
The line buildout (cable length) for the DS3 physical interface |
Hardware Address |
The port’s hardware address |
Port Statistics |
|
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Discards Input/Output |
The number of inbound/outbound packets chosen to be discarded to possibly free up buffer space |
Unknown proto discards Input/Output |
For packet-oriented interfaces, the number of packets received via the interface that were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing, the number of transmission units received via the interface that were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0. For ATM, this field displays cells discarded on an invalid vpi/vci. Unknown proto discards do not show up in the packet counts. |
*A:ALU-1># show port 1/4/1.e1 acr detail
=======================================================================
Adaptive Clock Recovery (ACR) Configuration
=======================================================================
Clock Master PW : 1/4/1.1
Clock Sync State : normal
-----------------------------------------------------------------------
CEM SAP Configuration Information
-----------------------------------------------------------------------
Endpoint Type : NxDS0 Bit-rate : 16
Payload Size : 32 Jitter Buffer : 5
Use RTP Header : No Differential : No
Timestamp Freq : 0 CAS Framing : No CAS
Effective PDVT : +/-2.500 ms
Cfg Alarm : stray malformed pktloss overrun underrun
Alarm Status :
-----------------------------------------------------------------------
CEM SAP Statistics
-----------------------------------------------------------------------
Packets Seconds Events
Egress Stats
Forwarded : 32993106
Dropped : 0
Missing : 0
Reordered Forwarded : 0
Underrun : 8058 0
Overrun : 0 0
Misordered Dropped : 0
Malformed Dropped : 0
LBit Dropped : 0
Error : 3
Severely Error : 2
Unavailable : 0
Failure Count : 1
Jitter Buffer Depth : 0
Ingress Stats
Forwarded : 32995595
Dropped : 0
=======================================================================
=======================================================================
Adaptive Clock Recovery (ACR)
- Internal Digital Phase Locked Loop (DPLL) Statistics
=======================================================================
frequency frequency phase phase
offset offset error error
mean stddev mean stddev
time (ppb) (ppb) (ns) (ns)
-----------------------------------------------------------------------
10/08/2008 11:27:11 220 1 273 94
10/08/2008 11:26:11 217 1 240 120
10/08/2008 11:25:11 214 1 79 157
10/08/2008 11:24:11 214 1 -15 102
10/08/2008 11:23:11 214 1 82 117
10/08/2008 11:22:11 213 1 12 113
10/08/2008 11:21:11 213 1 -64 119
10/08/2008 11:20:11 213 1 -66 126
10/08/2008 11:19:11 214 1 -41 117
10/08/2008 11:18:11 215 1 72 125
10/08/2008 11:17:11 214 1 -34 95
10/08/2008 11:16:11 214 1 -28 115
10/08/2008 11:15:11 215 1 30 89
10/08/2008 11:14:11 214 1 12 95
10/08/2008 11:13:11 214 1 19 144
-----------------------------------------------------------------------
Current
24 Hour
(137 min) 214 19
=======================================================================
=======================================================================
ACR State Statistics
=======================================================================
Algorithm State Counts
normal : 4121
Phase-tracking : 3
Freq-tracking : 0
Holdover : 0
Free-run : 8
Events
ACR Calc Out of Range : 0
Prolonged ACR Failure : 1
Excessive Packet Loss : 0
Excessive Phase Shift : 0
=======================================================================
Label |
Description |
---|---|
Adaptive Clock Recovery (ACR) Configuration |
|
Clock Master PW |
The SAP being used by the port for recovering the clock |
Clock Sync State |
The current state of the ACR adaptive algorithm |
CEM SAP Configuration Information |
|
Endpoint Type |
The type of endpoint |
Bit-rate |
The number of DS0s or timeslots in the channel group |
Payload Size |
The number of octets contained in the payload of a TDM PW packet when the packet is transmitted |
Jitter Buffer |
The size of the receive jitter buffer, expressed in milliseconds |
Use RTP Header |
Indicates whether RTP headers are used in CES packets (Yes or No) |
CAS Framing |
The type of CAS framing |
Effective PDVT |
The peak-to-peak packet delay variation (PDV) used by the circuit emulation service Since the operating system may adjust the jitter buffer setting in order to ensure no packet loss, the configured jitter buffer value may not be the value used by the system. The effective PDVT provides an indication that the PDV has been adjusted by the operating system. |
Cfg Alarm |
The alarms that have alarm reporting enabled |
Alarm Status |
The current alarm state (for example, stray, malformed, packet loss, overrun, underrun, remote packet loss, remote fault, or remote RDI) |
Internal Digital Phase Locked Loop (DPLL) Statistics |
|
ACR DPLL Statistics |
frequency offset mean: the ACR frequency offset mean for the previous 15 sets of 60-s intervals |
frequency offset stddev: the ACR frequency offset standard deviation for the previous 15 sets of 60-s intervals |
|
phase error mean: the ACR input phase error mean and output DCO mean for the previous 15 sets of 60-s intervals |
|
phase error stddev: the ACR input phase error standard deviation and output DCO standard deviation for the previous 15 sets of 60-s intervals |
|
ACR State Statistics |
|
Algorithm State Counts |
normal: the number of 2-s intervals the ACR algorithm was in the normal state |
Phase-tracking: the number of 2-s intervals the ACR algorithm was in the phase-tracking state |
|
Freq-tracking: the number of 2-s intervals the ACR algorithm was in the frequency tracking state |
|
Holdover: the number of 2-s intervals the ACR algorithm was in the holdover state |
|
Free-run: the number of 2-s intervals the ACR algorithm was in the free-run state |
|
Events |
ACR Calc Out of Range: the number of times the ACR algorithm was internally reset |
Prolonged ACR failure: the number of times the ACR algorithm was in the phase-tracking or holdover state for an extended period of time |
|
Excessive Packet Loss: increments every 2-second interval that ACR is in the phase-tracking state and the tolerated packet loss threshold is exceeded |
|
Excessive Phase Shift: increments each time the ACR algorithm transitions to the phase-tracking state from normal as a result of a phase shift above the tolerated shift level |
*A:ALU-1# show port dot1x 1/5/2 detail
===============================================================================
802.1x Port Status
===============================================================================
Port control : force-auth
Port status : authorized
Authenticator PAE state : force-auth
Backend state : initialize
Reauth enabled : yes Reauth period : 3500
Max auth requests : 2 Transmit period : 30
Supplicant timeout : 30 Server timeout : 30
Quiet period : 60
Radius-plcy : N/A
===============================================================================
802.1x Session Statistics
===============================================================================
authentication method : remote-radius
last session id : PAC-02A10000-8A61E689
last session time : 0497d02h
last session username : N/A
last session term cause : N/A
user tx octets : 0 user tx frames : 0
user rx octets : 0 user rx frames : 0
===============================================================================
802.1x Authentication Statistics
===============================================================================
tx frames : 0 rx frames : 0
tx req/id frames : 0 rx resp/id frames : 0
tx request frames : 0 rx response frames : 0
rx start frames : 0 rx logoff frames : 0
rx unknown frame type : 0 rx bad eap length : 0
rx last version : 0 rx last source mac :
===============================================================================
802.1x Authentication Diagnostics
===============================================================================
Enters Connecting : 0
EapLogoffs While Connecting : 0
Success While Authenticating : 0
Timeouts While Authenticating : 0
Failures While Authenticating : 0
Reauths While Authenticating : 0
EapStarts While Authenticating : 0
EapLogoffs While Authenticating : 0
Reauths While Authenticated : 0
EapStarts While Authenticated : 0
EapLogoffs While Authenticated : 0
Backend Responses : 0
Backend Access Challenges : 0
Backend Requests To Supplicant : 0
Backend Non Nak Responses : 0
Backend Auth Successes : 0
Backend Auth Failures : 0
===============================================================================
*A:ALU-1>#
Label |
Description |
---|---|
802.1x Port Status |
|
Port control |
auto: the 802.1x authentication mode is configured as automatic. The port starts in an unauthorized state and stays in that state until the first supplicant is authenticated successfully. |
force-auth: 802.1 authentication is disabled and the port is automatically authorized |
|
force-unauth: the port will always remain in the unauthorized state |
|
Port status |
authorized: the 802.1 port is authorized |
unauthorized: the 802.1 port is unauthorized |
|
Authenticator PAE state |
auto: the authenticator is set to the unauthorized state |
force-auth: the authenticator is set to the authorized state |
|
force-unauth: the authenticator is set to the unauthorized state |
|
Backend state |
request: the backend authentication machine is in the request state |
response: the backend authentication machine is in the response state |
|
success: the backend authentication machine is in the success state |
|
fail: the backend authentication machine is in the fail state |
|
timeout: the backend authentication machine is in the timeout state |
|
idle: the backend authentication machine is in the idle state |
|
initialize: the backend authentication machine is in the initialize state |
|
Reauth enabled |
Indicates whether reauthentication is enabled |
Max auth requests |
The maximum number of authentication requests the 7705 SAR sends to the RADIUS server before declaring the port unauthorized |
Supplicant timeout |
The number of seconds the 7705 SAR waits for a client to respond to an EAPOL message before considering the 802.1x authentication to have failed |
Quiet period |
The period, in seconds, between two authentication sessions during which no EAPOL frames are sent by the 7705 SAR |
Radius-plcy |
The name of the RADIUS policy used for 802.1x authentication |
Reauth period |
The delay, in seconds, before the 7705 SAR attempts reauthentication |
Transmit period |
The time, in seconds, that the 7705 SAR waits before sending a new EAPOL message |
Server timeout |
The time, in seconds, that the 7705 SAR waits for the RADIUS server to respond to the access request message before resending the request message the number of times specified by the max-auth-req command |
802.1x Session Statistics |
|
authentication method |
remote-radius: the authentication method used to establish the session |
last session id |
A unique identifier for the session, in the form of a printable ASCII string of at least three characters |
last session time |
The duration of the session in seconds |
last session username |
The username representing the identity of the supplicant PAE |
last session term cause |
The reason for the session termination: supplicantLogoff: the supplicant logged off |
portFailure: there was a port failure |
|
supplicantRestart: the supplicant state machine reinitialized |
|
reauthFailed: the reauthentication attempt failed |
|
authControlForceUnauth: the authentication mode was changed to always force unauthorized after being authorized |
|
portReInit: the port was reinitialized |
|
portAdminDisabled: the port was administratively disabled |
|
notTerminatedYet: the session has not been terminated |
|
user tx octets |
The number of octets transmitted in user data frames on this port during the session |
user rx octets |
The number of octets received in user data frames on this port during the session |
user tx frames |
The number of user data frames transmitted on this port during the session |
user rx frames |
The number of user data frames received on this port during the session |
802.1x Authentication Statistics |
|
tx frames |
The number of EAPOL frames of any type that have been transmitted by this authenticator |
tx req/id frames |
The number of EAP-Request/ID frames that have been transmitted by this authenticator |
tx request frames |
The number of EAP request frames (other than Request/ID frames) that have been transmitted by this authenticator |
rx start frames |
The number of EAPOL-Start frames that have been received by this authenticator |
rx unknown frame type |
The number of EAPOL frames that have been received by this authenticator in which the frame type is not recognized |
rx last version |
The protocol version number carried in the most recently received EAPOL frame |
rx frames |
The number of valid EAPOL frames of any type that have been received by this authenticator |
rx resp/id frames |
The number of EAP-Response/ID frames that have been received by this authenticator |
rx response frames |
The number of valid EAP response frames (other than Resp/ID frames) that have been received by this authenticator |
rx logoff frames |
The number of EAP-Logoff frames that have been received by this authenticator |
rx bad eap length |
The number of EAPOL frames that have been received by this authenticator in which the packet body length field is invalid |
rx last source mac |
The source MAC address carried in the most recently received EAPOL frame |
802.1x Authentication Diagnostics |
|
Enters Connecting |
Counts the number of times that the state machine transitions to the CONNECTING state from any other state |
EapLogoffs While Connecting |
Counts the number of times that the state machine transitions from CONNECTING to DISCONNECTED as a result of receiving an EAPOL-logoff message |
Success While Authenticating |
Counts the number of times that the state machine transitions from AUTHENTICATING to AUTHENTICATED, as a result of the backend authentication state machine indicating successful authentication of the supplicant (authSuccess = TRUE) |
Timeouts While Authenticating |
Counts the number of times that the state machine transitions from AUTHENTICATING to ABORTING, as a result of the backend authentication state machine indicating authentication timeout (authTimeout = TRUE) |
Failures While Authenticating |
Counts the number of times that the state machine transitions from AUTHENTICATING to HELD, as a result of the backend authentication state machine indicating authentication failure (authFail = TRUE) |
Reauths While Authenticating |
Counts the number of times that the state machine transitions from AUTHENTICATING to ABORTING, as a result of a reauthentication request (reAuthenticate = TRUE) |
EapStarts While Authenticating |
Counts the number of times that the state machine transitions from AUTHENTICATING to ABORTING, as a result of an EAPOL-Start message being received from the supplicant |
EapLogoffs While Authenticating |
Counts the number of times that the state machine transitions from AUTHENTICATING to ABORTING, as a result of an EAPOL-Logoff message being received from the supplicant |
Reauths While Authenticated |
Counts the number of times that the state machine transitions from AUTHENTICATED to CONNECTING, as a result of a reauthentication request (reAuthenticate = TRUE) |
EapStarts While Authenticated |
Counts the number of times that the state machine transitions from AUTHENTICATED to CONNECTING, as a result of an EAPOL-Start message being received from the supplicant |
EapLogoffs While Authenticated |
Counts the number of times that the state machine transitions from AUTHENTICATED to DISCONNECTED, as a result of an EAPOL-Logoff message being received from the supplicant |
Backend Responses |
Counts the number of times that the state machine sends an initial Access-Request packet to the authentication server (that is, executes sendRespToServer on entry to the RESPONSE state) Indicates that the authenticator attempted communication with the authentication server |
Backend Access Challenges |
Counts the number of times that the state machine receives an initial Access-Challenge packet from the authentication server (that is, aReq becomes TRUE, causing an exit from the RESPONSE state) Indicates that the authentication server has communication with the authenticator |
Backend Requests To Supplicant |
Counts the number of times that the state machine sends an EAP-Request packet (other than an Identity, Notification, Failure, or Success message) to the supplicant (that is, executes txReq on entry to the REQUEST state) Indicates that the authenticator chose an EAP-method |
Backend Non Nak Responses |
Counts the number of times that the state machine receives a response from the supplicant to an initial EAP-Request, and the response is something other than EAP-NAK (that is, rxResp becomes TRUE, causing the state machine to transition from REQUEST to RESPONSE, and the response is not an EAP-NAK) Indicates that the supplicant can respond to the authenticator's chosen EAP-method |
Backend Auth Successes |
Counts the number of times that the state machine receives an EAP-Success message from the authentication server (that is, aSuccess becomes TRUE, causing a transition from RESPONSE to SUCCESS) Indicates that the supplicant has successfully authenticated to the authentication server |
Backend Auth Failures |
Counts the number of times that the state machine receives an EAP-Failure message from the authentication server (that is, aFail becomes TRUE, causing a transition from RESPONSE to FAIL) Indicates that the supplicant has not authenticated to the authentication server |
*A:ALU-1># show port 1/4/1 description
===============================================================================
Port Descriptions on Slot 1
===============================================================================
Port Id Description
-------------------------------------------------------------------------------
1/4/1 DS3/E3
===============================================================================
*A:ALU-1>
Label |
Description |
---|---|
Port Id |
The port identifier |
Description |
A text description of the port |
*A:ALU-1># show port 1/5/1 associations
==============================================================================
Interface Table
==============================================================================
Router/ServiceId Name Encap Val
------------------------------------------------------------------------------
Router: Base if1000 1000
Router: Base if2000 2000
------------------------------------------------------------------------------
Interfaces
==============================================================================
*A:ALU-1>
Label |
Description |
---|---|
Router/ServiceId |
The service identifier |
Name |
The name of the IP interface |
Encap Val |
The dot1q, null, or qinq encapsulation value on the port for this IP interface |
*A:ALU-1># show port 1/2/1.1 ima-link
===============================================================================
State Information
===============================================================================
Transmit Link Identifier: 0
Receive Link Identifier : 0
Near Rx Failure State : IMA Link Failure
Far End Rx Failure State: IMA Link Failure
Near End Tx State : Unusable - No given reason
Near End Rx State : Unusable - No given reason
Far End Tx State : Unusable - No given reason
Far End Rx State : Unusable - No given reason
Link Test State : Disabled
Rx Test Pattern : 0
===============================================================================
TC Sublayer Information
===============================================================================
TC Alarm State : LCD Failure Number OCD Events : 0
HEC Errors (Dropped) : 0 HEC Errors (Fixed) : 0
===============================================================================
Statistical Information
===============================================================================
Num Violations : 0 Num OIF Anomalies : 0
NE Severely Err. Seconds: 0 FE Severely Err. Seconds: 0
NE Unavail. Seconds : 0 FE Unavail. Seconds : 0
NE Tx Unused Seconds : 0 FE Tx Unused Seconds : 0
NE Rx Unused Seconds : 0 FE Rx Unused Seconds : 0
NE Tx Num Failures : 0 NE Rx Num Failures : 0
FE Tx Num Failures : 0 FE Rx Num Failures : 0
Tx ICP Cell count : 0 Rx ICP Cell count : 0
Error ICP Cells Total : 0 Rx Lost ICP Cells Total : 0
Relative Link Delay : 0
===============================================================================
*A:ALU-1#
Label |
Description |
---|---|
State Information |
|
Transmit Link Identifier |
The identifier of the IMA link used to transmit data |
Receive Link Identifier |
The identifier of the IMA link used to receive data |
Near Rx Failure State |
The failure state of the near-end receive link |
Far End Rx Failure State |
The failure state of the far-end receive link |
Near End Tx State |
The state of the near-end transmit link |
Near End Rx State |
The state of the near-end receive link |
Far End Tx State |
The state of the far-end transmit link |
Far End Rx State |
The state of the far-end receive link |
Link Test State |
The state of the link test procedure: Enabled or Disabled |
Rx Test Pattern |
The received test pattern in an IMA link loopback operation (0 to 255) |
TC Sublayer Information |
|
TC Alarm State |
The alarm state for the traffic class of the IMA link |
HEC Errors (Dropped) |
The number of HEC errors resulting in dropped packets |
Number OCD Events |
The number of OCD events |
HEC Errors (Fixed) |
The number of HEC errors fixed |
Statistical Information |
|
Num Violations |
The number of violations (path, line, code, and length) |
NE Severely Err. Seconds |
The number of near-end severely errored seconds |
NE Unavail. Seconds |
The number of seconds that the near end has been unavailable |
NE Tx Unused Seconds |
The number of seconds that the near-end transmit link has been unused |
NE Rx Unused Seconds |
The number of seconds that the near-end receive link has been unused |
NE Tx Num Failures |
The number of near-end transmit link failures |
FE Tx Num Failures |
The number of far-end transmit link failures |
Tx ICP Cell count |
The number of ICP cells transmitted on the IMA link |
Error ICP Cells Total |
The total number of errored ICP cells on the IMA link |
Relative Link Delay |
The time delay, in seconds, between detection of a link activation/deactivation condition and acting upon it (going in/out of the Rx failure state on a link) |
Num OIF Anomalies |
The number of OIF anomalies for the IMA link |
FE Severely Err. Seconds |
The number of far-end severely errored seconds |
FE Unavail. Seconds |
The number of seconds that the far end has been unavailable |
FE Tx Unused Seconds |
The number of seconds that the far-end transmit link has been unused |
FE Rx Unused Seconds |
The number of seconds that the far end receive link has been unused |
NE Rx Num Failures |
The number of near-end receive link failures |
FE Rx Num Failures |
The number of far-end receive link failures |
Rx ICP Cell count |
The number of ICP cells received on the IMA link |
Rx Lost ICP Cells Total |
The total number of lost ICP cells received on the IMA link |
*A:ALU-1># show port 1/4/1.5 ppp
===============================================================================
PPP Protocols for 1/4/1.5
===============================================================================
Protocol State Last Change Restart Count Last Cleared
-------------------------------------------------------------------------------
lcp initial 10/12/2007 20:15:54 0 10/12/2007 20:15:54
ipcp initial 10/12/2007 20:15:54 0 10/12/2007 20:15:54
mplscp initial 10/12/2007 20:15:54 0 10/12/2007 20:15:54
bcp initial 10/12/2007 20:15:54 0 10/12/2007 20:15:54
osicp initial 10/12/2007 20:15:54 0 10/12/2007 20:15:54
ipv6cp initial 10/12/2007 20:15:54 0 10/12/2007 20:15:54
===============================================================================
===============================================================================
PPP Statistics
===============================================================================
Local Mac address : 2001:db8:: Remote Mac address :
Local Magic Number : 0x0 Remote Magic Number: 0x0
Local address : 10.0.0.0 Remote address : 10.0.0.0
Line Monitor Method: keepalive
Keepalive statistics
Request interval : 10 Threshold exceeded : 0
Drop Count : 3 In packets : 0
Time to link drop : 00h00m30s Out packets : 0
Last cleared time : 10/12/2007 20:15:54
===============================================================================
*A:ALU-1>#
Label |
Description |
---|---|
Protocol |
The applicable protocols for the specified port |
State |
The current status of a PPP link. Values are initial, starting, closed, stopped, closing, stopping, requestSent, ackReceived, ackSent, opened. |
Last Change |
The last time the PPP link state changed |
Restart Count |
The number of times that this Control Protocol has reached the open state |
PPP Statistics |
|
Last Cleared |
The date and time the restart count was set to zero |
Local Mac address |
The MAC address assigned to the local end of the PPP link |
Remote Mac address |
The Ethernet MAC address sent by the remote end of the PPP link |
Local Magic Number |
The local magic number to be sent to the peer. The magic number provides a method to detect loopbacks. If the value of the local magic number is the same as the value of the remote magic number, then it is possible that the link might be looped back. If the two magic numbers do not match, the link is not looped back. |
Remote Magic Number |
The magic number sent by the peer. If the value of the remote magic number is the same as the value of the local magic number, then it is possible that the link might be looped back. If the two magic numbers do not match, the link is not looped back. |
Local Address |
The IP address at the local end of the link |
Remote Address |
The IP address at the remote end of the link |
Line Monitor Method |
The type of line monitoring packets being sent and received on this PPP link |
Request Interval |
The time interval in seconds at which keepalive requests are issued |
Threshold exceeded |
The number of times that the drop count was reached |
Drop Count |
The number of keepalive or LQR messages that were missed before the line was brought down |
In packets |
The number of echo-reply packets received |
Time to link drop |
The time remaining before the link will be declared dropped if a keepalive echo reply packet is not received |
Out packets |
The number of echo-request packets sent |
Last cleared time |
The time since the last clear |
*A:ALU-1># show port cem
=============================================================================
Ports on Slot 1
=============================================================================
Port Admin Link Port Clock Master Clock
Id State State Src Port Id State
-----------------------------------------------------------------------------
1/9/1.1.2 Up No Down differential 1/9/1.1.2.1 hold-over
1/9/1.1.3 Up No Down node-timed
1/9/1.1.4 Up No Down node-timed
...
-----------------------------------------------------------------------------
Label |
Description |
---|---|
Port Id |
The port ID, in the slot/mda/port format |
Admin State |
The administrative state of the interface connection |
Link |
Indicates whether the link is active |
Port State |
The state level of the port |
Clock Src |
The clock source |
Master Port Id |
The master port ID |
Clock State |
The clock state |
*A:ALU-1# show port 1/2/32.1 frame-relay
=============================================================================
Frame Relay Info for 1/2/32.1
===============================================================================
Mode : dce LMI Type : itu
FR Interface Status : fault
N391 DTE : 6 N392 DCE : 3
N392 DTE : 3 N393 DCE : 4
N393 DTE : 4 T392 DCE : 15
T391 DTE : 10
FRF-12 : Disabled
Link Identifier : N/A
Tx Status Enquiry : 1097 Rx Status Enquiry : 0
Rx Status Messages : 0 Tx Status Messages : 0
Status Message Timeouts : 1096 Status Enquiry Timeouts : 0
Discarded Messages : 0 Inv. RxSeqNum Messages : 0
===============================================================================
===============================================================================
frame-relay statistics for port "1/2/32.1"
===============================================================================
Received Transmitted
-------------------------------------------------------------------------------
Frames 0 0
Octets 0 0
DEFrames 0 0
DEOctets 0 0
FECNFrames 0 0
BECNFrames 0 0
Invalid Dlci 0 -
Last Invalid Dlci - -
Crc Errors 0 -
Alignment Errors 0 -
Length Violations 0 -
Illegal Header 0 -
Underruns Errors - 0
Other Errors 0 0
===============================================================================
Label |
Description |
---|---|
Frame Relay Info for port identifier |
|
Mode |
The frame relay mode:
|
LMI Type |
The LMI type:
|
FR Interface Status |
The status of the frame relay interface as determined by the performance of the DLCMI. If no DLCMI is running, the frame relay interface will stay in the running state indefinitely. |
N391 DTE |
The DTE full status polling interval for the frame relay LMI. The number specifies the frequency at which inquiries expect a full status report. |
N392 DCE |
The DCE error threshold for the frame relay LMI. The threshold specifies the number of errors needed to bring down a link. |
N392 DTE |
The DTE error threshold for the frame relay LMI. The threshold specifies the number of errors needed to bring down a link. |
N393 DCE |
The DCE monitored event count for the frame relay LMI |
N393 DTE |
The DTE monitored event count for the frame relay LMI |
T392 DCE |
The DCE keepalive timer for the frame relay LMI. The number specifies the interval at which the DCE checks for keepalive responses from the DTE. |
T391 DTE |
The DTE keepalive timer for the frame relay LMI. The number specifies the interval at which the DTE sends a keepalive response request to the DCE. |
FRF-12 |
Not supported |
Link Identifier |
The link associated with the frame relay port |
Tx Status Enquiry |
The number of status enquiries sent |
Rx Status Enquiry |
The number of status enquiries received |
Rx Status Messages |
The number of status messages received |
Tx Status Messages |
The number of status messages sent |
Status Message Timeouts |
The number of status message timeouts |
Status Enquiry Timeouts |
The number of status enquiry timeouts |
Discard Messages |
The number of status enquiry messages discarded due to errors |
Inv. RxSeqNum Messages |
The number of LMI messages received with an invalid sequence number |
frame-relay statistics for port port-identifier (input and output values) |
|
Frames |
The number of frames received or transmitted |
Octets |
The number of octets received or transmitted |
DEFrames |
The number of packets received or transmitted with the DE bit set |
DEOctets |
The number of octets received or transmitted with the discard eligibility (DE) bit set |
FECNFrames |
The number of frames received or transmitted with the forward explicit congestion notification bit set |
BECNFrames |
The number of frames received or transmitted with the backward explicit congestion notification bit set |
Invalid Dlci |
The number of invalid DLCIs |
Last Invalid Dlci |
The last time when an invalid DLCI was detected |
Crc Errors |
The number of cyclical redundancy check errors |
Alignment Errors |
The total number of packets received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but that had either a bad frame check sequence with an integral number of octets (FCS error) or a bad FCS with a non-integral number of octets |
Length Violations |
The number of packet length violations |
Illegal Header |
The number of header configuration errors |
Underruns Errors |
The number of frames that were unsuccessfully transmitted because transmission was not fast enough to maintain synchronization |
Other Errors |
The number of other unspecified errors |
*A:ALU-1# show port 1/2/32.1 frame-relay dlci 16
===============================================================================
Frame Relay Info for 1/2/32.1
===============================================================================
Mode : dte LMI Type : ansi
FR Interface Status : fault
N391 DTE : 6 N392 DCE : 3
N392 DTE : 3 N393 DCE : 4
N393 DTE : 4 T392 DCE : 15
T391 DTE : 10
FRF-12 : Disabled
Link Identifier : N/A
Tx Status Enquiry : 0 Rx Status Enquiry : 0
Rx Status Messages : 0 Tx Status Messages : 0
Status Message Timeouts : 0 Status Enquiry Timeouts : 0
Discarded Messages : 0 Inv. RxSeqNum Messages : 0
===============================================================================
=================================================
Frame Relay PVCs
=================================================
Dlci State Type Creation Time
-------------------------------------------------
16 Inactive Static 07/11/2011 15:27:27
-------------------------------------------------
PVCs: 1
=================================================
===============================================================================
frame-relay statistics for port "1/2/32.1" dlci "16"
===============================================================================
Input Output
-------------------------------------------------------------------------------
Frames 1077 2920112
Octets 0 4294967295
FECNs 32 3247074
BECNs 4294967295 1837088656
DE Frames 3621691 68756528
DE Octets 1990621688 1
Discards 1893384560 2920112
Crc Discard 2 -
Aborts 56295902 -
Other Discard 1837088656 -
===============================================================================
*A:ALU-1#
Label |
Description |
---|---|
Frame Relay Info for port-identifier |
|
— |
|
Frame Relay PVCs |
|
Dlci |
The specified DLCI |
State |
The port state |
Type |
The port type |
Creation Time |
The time at which the port was created |
PVCs |
The number of PVCs |
frame-relay statistics for port port-identifier (input and output values) |
|
Frames |
The number of frames received or transmitted |
Octets |
The number of octets received or transmitted |
DE Frames |
The number of packets received or transmitted with the DE bit set |
DE Octets |
The number of octets received or transmitted with the discard eligibility bit set |
Crc Discard |
The number of cyclical redundancy check discards |
Aborts |
The number of aborts |
Other Discard |
The number of other discards |
*A:7705:Dut-C#show port 1/10/9.1 detail
===============================================================================
TDM DS0 Chan Group
===============================================================================
Description : DS0GRP
Interface : 1/10/9.1
TimeSlots : 2-32
Speed : 64 CRC : 16
Admin Status : up Oper Status : up
Last State Change : 07/12/2011 08:17:15 Chan-Grp IfIndex : 591691837
Configured mode : access Encap Type : hdlc
Admin MTU : 1514 Oper MTU : 1514
Scramble : false
Physical Link : yes Bundle Number : none
Idle Cycle Flags : flags Load-balance-algo : n/a
Payload Fill Type : n/a Payload Pattern : N/A
Signal Fill Type : n/a Signal Pattern : N/A
Ing. Pool % Rate : 100 Egr. Pool % Rate : 100
Egr. Sched. Pol : N/A
===============================================================================
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 304520 301852
Packets 3310 3281
Errors 0 0
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 3310 3281
Discards 0 0
Unknown Proto Discards 0
===============================================================================
*A:7705:Dut-C# configure port 1/10/9
*A:7705:Dut-C# show port detail 1/5/1.1
===============================================================================
TDM DS0 Chan Group
===============================================================================
Description : DS0GRP
Interface : 1/5/1.1
TimeSlots : 2-32
Speed : 64 CRC : 16
Admin Status : up Oper Status : up
Last State Change : 07/12/2011 08:17:18 Chan-Grp IfIndex : 580943933
Configured mode : access Encap Type : cisco-hdlc
Admin MTU : 1514 Oper MTU : 1514
Scramble : false
Physical Link : yes Bundle Number : none
Idle Cycle Flags : flags Load-balance-algo : n/a
Payload Fill Type : n/a Payload Pattern : N/A
Signal Fill Type : n/a Signal Pattern : N/A
Ing. Pool % Rate : 100 Egr. Pool % Rate : 100
Egr. Sched. Pol : N/A
===============================================================================
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 301852 304520
Packets 3281 3310
Errors 0 0
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 3281 3310
Discards 0 0
Unknown Proto Discards 0
===============================================================================
*A:7705:Dut-C# configure port 1/10/9
*A:7705:Dut-C# config>port>serial>x21>channel-group# show port 1/3/1.1
===============================================================================
Serial DS0 Chan Group
===============================================================================
Description : DS0GRP
Interface : 1/3/1.1
CRC : 16
Admin Status : down Oper Status : down
Last State Change : 01/27/2012 14:32:01 Chan-Grp IfIndex : 576749629
Configured Mode : access Encap Type : cisco-hdlc
Admin MTU : 1514 Oper MTU : 1514
Physical Link : No Bundle Number : none
Idle Cycle Flags : flags
Payload Fill Type : n/a Payload Pattern : n/a
===============================================================================
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 118222 30008
Packets 1640 1364
Errors 0 0
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 1640 1364
Discards 0 0
Unknown Proto Discards 0
===============================================================================
*A:7705:Dut-C# config>port>serial>x21>channel-group# show port 1/3/8
===============================================================================
Serial RS-232 Physical Interface
===============================================================================
Description : ozgur
Interface : 1/3/8 Port IfIndex : 40108032
Admin Status : up Oper Status : up
Physical Link : Yes
Type : v35
===============================================================================
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 0 0
Discards 0 0
Unknown Proto Discards 0
===============================================================================
*A:7705:Dut-C# config>port>serial>x21>channel-group#
*A:7705:Dut-C# config>port>serial>x21>channel-group# show port 1/3/8.1 detail
===============================================================================
Serial DS0 Chan Group
===============================================================================
Description : DS0GRP
Interface : 1/3/8.1
CRC : 32
Admin Status : up Oper Status : up
Last State Change : 01/27/2012 10:37:44 Chan-Grp IfIndex : 576979019
Configured Mode : access Encap Type : hdlc
Admin MTU : 1514 Oper MTU : 1514
Physical Link : Yes Bundle Number : none
Idle Cycle Flags : flags
Payload Fill Type : n/a Payload Pattern : n/a
===============================================================================
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 0 0
Packets 0 0
Errors 0 0
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 0 0
Discards 0 0
Unknown Proto Discards 0
===============================================================================
*A:7705:Dut-C# config>port>serial>x21>channel-group#
Output Example
*A:ALU-1># show port 1/1/3
===============================================================================
TDM Data Physical Interface
===============================================================================
Description : G.703 64kbps Codirectional
Interface : 1/1/3 Port IfIndex : 39878656
Admin Status : down Oper Status : down
Physical Link : No
Type : codir
===============================================================================
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 0 0
Discards 0 0
Unknown Proto Discards 0
===============================================================================
*A:ALU-1># show port 1/2/3.codir detail
===============================================================================
TDM Data Interface
===============================================================================
Description : CODIR
Interface : 1/2/3.codir
Type : codir
Admin Status : down Oper Status : down
Physical Link : no Clock Source : node-timed
Timing 8khz : Disabled
Last State Change : 05/27/2013 12:42:10 Channel IfIndex : 574717955
Loopback : none
Cfg Alarm : ais los
Alarm Status : los
===============================================================================
===============================================================================
Traffic Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Octets 0 0
Packets 0 0
Errors 0 0
============================
Codir Line
============================
Receive:
Data-slip : 0
============================
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 0 0
Discards 0 0
Unknown Proto Discards 0
===============================================================================
*A:ALU-1>#
Label |
Description |
---|---|
TDM Data Physical Interface TDM Data Interface |
|
Description |
A text description of the port |
Interface |
The port ID displayed in the slot/mda/port format |
Port IfIndex |
The port interface's index number, which reflects its initialization sequence |
Admin Status |
up: the administrative state is up |
down: the administrative state is down |
|
Oper Status |
up: the operating state is up |
down: the operating state is down |
|
Physical Link |
yes: there is no alarm condition for the link |
no: there is an outstanding alarm condition for the link |
|
Type |
The type of interface: codirectional or TPIF |
Clock Source |
loop-timed: the link recovers the clock from the received data stream node-timed: the link uses the internal clock when transmitting data adaptive: clocking is derived from the incoming pseudowire packets differential: clocking is derived from a common clock compared to differential clock recovery data in the RTP header in the TDM PW overhead |
Timing 8khz |
Indicates whether 8-kb/s timing on a codirectional interface is enabled or disabled |
Last State Change |
The last time the operational status of the port changed state |
Channel IfIndex |
The channel interface index number |
Loopback |
The loopback mode for the channel: internal-analog, internal-digital, or none |
Cfg Alarm |
The type of alarms to be logged and reported for the port |
Alarm Status |
The current alarm state |
Traffic Statistics |
|
Octets Input/Output |
The total number of octets received and transmitted on the port |
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Errors Input/Output |
For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol. For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors. |
Codir Line |
|
Data-slip: |
In a plesiochronous timing system, the number of data slips that have occurred in the receive direction |
Port Statistics |
|
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a multicast or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Discards Input/Output |
The number of inbound/outbound packets chosen to be discarded to possibly free up buffer space |
Unknown Proto Discards Input/Output |
For packet-oriented interfaces, the number of packets received at the interface that were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing, the number of transmission units received at the interface that were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0. |
*A:ALU-1># show port 1/3/1
===============================================================================
GNSS Physical Interface
===============================================================================
Description : GNSS Rx
Interface : 1/3/1 Port IfIndex : 39878656
Admin Status : up Oper Status : up
Physical Link : Yes
Type : gps
Ant. Cable Delay : 0 Elev. Mask Angle : 10
Antenna Status : ok Visible Satellites : 9
Sync Status : locked Used Satellites : 7
Receiver Status : Position Hold
Time : 2014/04/23 18:47:38 Latitude : +45.34811
UTC Offset : 17 Longitude : -75.92142
Altitude (m MSL) : 90
===============================================================================
Label |
Description |
---|---|
Description |
Specifies the GNSS RF port description |
Interface |
Specifies the card, MDA, and port number of the GNSS RF port |
Admin Status |
up: the port is administratively up down: the port is administratively down |
Physical Link |
yes: an operational GNSS antenna is detected no: an operational GNSS antenna is not detected |
Type |
Specifies the type of satellite navigation system used |
Ant. Cable Delay |
Specifies the amount of time, in nanoseconds, compensated for signal delay due to cable length |
Antenna Status |
ok: valid antenna connection under-current: open condition. Previously, an under-current status caused the port operational status to be down. Currently, the port remains operationally up in the event that any GNSS splitters used do not provide a load. over-current: short circuit, or maximum power limits for the receiver have been exceeded no-bias voltage: antenna power disabled |
Sync Status |
locked: GNSS time is within alarm limits (1 μs) not locked: GNSS time is outside of the alarm limits and/or there is an insufficient number of tracked satellites |
Receiver Status |
Acquiring Satellites: GNSS receiver is attempting to track satellite Position Hold: GNSS receiver position is determined and GNSS receiver is no longer solving for position 2D Fix: GNSS receiver is attempting to get a 2D fix on a satellite 3D Fix: GNSS receiver is attempting to get a 3D fix on a satellite Unknown: default state on power-up Communication Lost: occurs after 30 s of no Channel/Data/Status messages from the GNSS receiver Communication Established: occurs after a successful re-establishment of communication following a Communication Lost status Self-Test Failed: occurs after a GNSS receiver startup failure |
Time |
Specifies the GNSS system date and time |
UTC Offset |
Specifies the difference between GNSS time and UTC time UTC time = GNSS time – UTC offset |
Port IfIndex |
Specifies the GNSS interface index number, which reflects its initialization sequence |
Oper Status |
up: the port is operationally up (communication with the GNSS receiver is established, the self-test has passed, and the antenna status is OK) down: the port is operationally down (any of the up conditions have not been met) |
Elev. Mask Angle |
Specifies the configured elevation angle below which satellites are ignored. The default elevation mask angle is 10°. |
Visible Satellites |
Specifies the number of satellites that the GNSS receiver should see at the current time. This number can be 0 if the GNSS receiver has not yet downloaded an almanac, even if Used Satellites is more than 0. Five or more satellites must be in view of the GNSS receiver antenna at all times when the receiver is in the process of obtaining a position fix, and these satellites must be above the configured elevation mask angle. |
Used Satellites |
Specifies the number of tracked satellites |
Latitude |
Specifies the latitude of the GNSS antenna |
Longitude |
Specifies the longitude of the GNSS antenna |
Altitude (m MSL) |
Specifies the altitude of the GNSS antenna above mean sea level, in meters |
*A:Sar8 Dut-A>show# port aps
===============================================================================
Ports on APS Groups
===============================================================================
Port Admin Link Port Cfg Oper LAG/ Port Port Port C/QS/S/XFP/
Id State State MTU MTU Bndl Mode Encp Type MDIMDX
-------------------------------------------------------------------------------
aps-1 Down No Ghost
===============================================================================
*A:Sar8 Dut-A>show#
Label |
Description |
---|---|
Port Id |
The port ID configured or displayed in the aps-id format |
Admin State |
Up: the administrative state is up |
Down: the administrative state is down |
|
Link |
Yes: a physical link is present |
No: a physical link is not present |
|
Port State |
Up: the port is physically present and has a physical link |
Down: the port is physically present but does not have a link |
|
Ghost: the port is not physically present |
|
None: the port is in its initial creation state or about to be deleted |
|
Link Up: the port is physically present and has a physical link. When Link Up appears at the lowest level of a TDM tributary, it means the physical connection is active but the port is waiting before data traffic can flow. It is a waiting state and indicates that data traffic will not flow until it transitions to the Up state. |
|
Link Down: the port is physically present but does not have a link |
|
Cfg MTU |
The configured MTU |
Oper MTU |
The negotiated size of the largest packet that can be sent on the port or channel specified in octets |
LAG/Bndl |
The Link Aggregation Group (LAG) or multilink bundle to which a TDM port is assigned |
Port Mode |
network: the port is configured for transport network use |
access: the port is configured for service access |
|
hybrid: the port is configured for hybrid use (transport network and service access per VLAN) |
|
Port Encp |
The encapsulation type on the port |
Port Type |
The type of port or optics installed |
C/QS/S/XFP/MDIMDX |
The SFP type on the port |
*A:Sar8 Dut-A>show# port aps-1
===============================================================================
SONET/SDH Interface
===============================================================================
Description : APS Group
Interface : aps-1 Speed : oc3
Admin Status : down Oper Status : down
Physical Link : No Loopback Mode : none
Single Fiber Mode : No
Clock Source : node Framing : sonet
Last State Change : 01/09/2019 20:50:16 Port IfIndex : 1358987264
Configured Address : d6:64:ff:00:02:49
Hardware Address : d6:64:ff:00:02:49
Last Cleared Time : 01/24/2019 21:33:06
J0 String : 0x01 Section Trace Mode : byte
Rx S1 Byte : 0x00 (stu) Rx K1/K2 Byte : 0x00/0x00
Tx S1 Byte : 0x00 (stu) Tx DUS/DNU : Disabled
Rx J0 String (Hex) : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Cfg Alarm : loc lrdi lb2er-sf slof slos
Alarm Status :
BER SD Threshold : 6 BER SF Threshold : 3
Hold time up : 500 milliseconds Reset On Path Down : Disabled
Hold time down : 200 milliseconds
Transceiver Data
Transceiver Status : not-equipped
Hardware Address : d6:64:ff:00:02:49
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 0 0
Discards 0 0
Unknown Proto Discards 0
===============================================================================
Label |
Description |
---|---|
SONET/SDH Interface |
|
Description |
A description of the port |
Interface |
The APS interface name (the APS group port) |
Speed |
The speed of the SONET/SDH port |
Admin Status |
Specifies whether the APS circuit is administratively up or down |
Oper Status |
Specifies whether the APS circuit is operationally up or down |
Physical Link |
Specifies whether or not a physical link is present |
Loopback Mode |
The loopback mode of the port |
Single Fiber Mode |
Specifies whether the port is operating in single-fiber mode |
Clock Source |
node: the link uses the internal clock when transmitting data loop: the link recovers the clock from the received data stream |
Framing |
sonet: the port is configured for SONET framing sdh: the port is configured for SDH framing |
Last State Change |
The last time that the operational status of the port changed state |
Port IfIndex |
The interface index number, which reflects its initialization sequence |
Configured Address |
The base chassis SONET/SDH MAC address |
Hardware Address |
The interface hardware- or system-assigned MAC address at its protocol sublayer |
Last Cleared Time |
The time since the last clear |
J0 String |
The section trace value that is sent to the far-end port |
Section Trace Mode |
byte: the section trace in the SONET section header is set in bytes string: a text string is used to identify the SONET section header increment-z0: an incremental STM ID is configured instead of a static value |
Rx S1 Byte |
The value of the SONET/SDH S1 byte received on the interface |
Rx K1/K2 Byte |
The value of the SONET/SDH K1/K2 byte received on the interface |
Tx S1 Byte |
The value of the SONET/SDH S1 byte transmitted on the interface |
Tx DUS/DNU |
Indicates whether the transmission of the QL-DUS/DNU value in synchronization status messages is enabled or disabled on the port |
Rx J0 String (Hex) |
The hexadecimal value of the received J0 |
Cfg Alarm |
The types of alarms to be logged and reported for the SONET/SDH port |
Alarm Status |
The current alarm state |
BER SD Threshold |
The configured threshold for line signal degradation BER error rate, that when crossed determines the signal degradation and signal failure |
BER SF Threshold |
The configured threshold for line signal failure BER error rate, that when crossed determines the signal degradation and signal failure |
Hold time up |
The link-up dampening time in seconds |
Reset On Path Down |
Specifies whether or not the port will be reset when the path transitions to the operationally down state |
Hold time down |
The link-down dampening time in seconds |
Transceiver Data |
The following information is provided for a configured SFP:
|
Transceiver Status |
The status of the transceiver |
Hardware Address |
The port hardware address |
Port Statistics |
|
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a unicast, multicast, or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Discards Input/Output |
The number of inbound/outbound packets chosen to be discarded to possibly free up buffer space |
Unknown Proto Discards Input/Output |
For packet-oriented interfaces, the number of packets received via the interface that were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing, the number of transmission units received via the interface that were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0. Unknown proto discards do not show up in the packet counts. |
*A:Sar8 Dut-A>show# port lcr
===============================================================================
Ports on LCR Groups
===============================================================================
Port Admin Link Port Cfg Oper LAG/ Port Port Port C/QS/S/XFP/
Id State State MTU MTU Bndl Mode Encp Type MDIMDX
-------------------------------------------------------------------------------
lcr-1/1 Down No Ghost
lcr-1/2 Down No Ghost
lcr-1/3 Down No Ghost
lcr-1/4 Down No Ghost
lcr-1/5 Down No Ghost
lcr-1/6 Down No Ghost
lcr-1/7 Down No Ghost
lcr-1/8 Down No Ghost
lcr-1/9 Down No Ghost
lcr-1/10 Down No Ghost
lcr-1/11 Down No Ghost
lcr-1/12 Down No Ghost
lcr-1/13 Down No Ghost
lcr-1/14 Down No Ghost
lcr-1/15 Down No Ghost
lcr-1/16 Down No Ghost
lcr-5/1 Down No Ghost
lcr-5/2 Down No Ghost
lcr-5/3 Down No Ghost
===============================================================================
Label |
Description |
---|---|
Port Id |
The port ID configured or displayed in the slot/mda/port format |
Admin State |
Up: the administrative state is up |
Down: the administrative state is down |
|
Link |
Yes: a physical link is present |
No: a physical link is not present |
|
Port State |
Up: the port is physically present and has a physical link |
Down: the port is physically present but does not have a link |
|
Ghost: the port is not physically present |
|
None: the port is in its initial creation state or about to be deleted |
|
Link Up: the port is physically present and has a physical link When Link Up appears at the lowest level of a TDM tributary, it means the physical connection is active but the port is waiting before data traffic can flow. It is a waiting state and indicates that data traffic will not flow until it transitions to the Up state. |
|
Link Down: the port is physically present but does not have a link |
|
Cfg MTU |
The configured MTU |
Oper MTU |
The negotiated size of the largest packet that can be sent on the port or channel specified in octets |
LAG/Bndl |
The Link Aggregation Group (LAG) or multilink bundle to which a TDM port is assigned |
Port Mode |
network: the port is configured for transport network use |
access: the port is configured for service access |
|
hybrid: the port is configured for hybrid use (transport network and service access per VLAN) |
|
Port Encp |
The encapsulation type on the port |
Port Type |
The type of port or optics installed |
C/QS/S/XFP/MDIMDX |
The SFP type on the port |
*A:Sar8 Dut-A>show# port lcr-1/1
===============================================================================
TDM DS1 Physical Interface
===============================================================================
Description : APS Group
Interface : lcr-1/1 Port IfIndex : 1367343104
Admin Status : down Oper Status : down
Physical Link : No
Line Impedance : 100
Line Encoding : b8zs
Type : ds1 Buildout : short
Length : 133
Hardware Address :
===============================================================================
===============================================================================
Port Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
Packets 0 0
Discards 0 0
Unknown Proto Discards 0
===============================================================================
Label |
Description |
---|---|
TDM DS1 Physical Interface |
|
Description |
A text description of the LCR port |
Interface |
The LCR port ID displayed in the lcr-group-id/port[.channel] format |
Port Ifindex |
The interface index number, which reflects its initialization sequence |
Admin Status |
up: the LCR port is administratively up |
down: the LCR port is administratively down |
|
Oper Status |
up: the LCR port is operationally up |
down: the LCR port is operationally down |
|
Physical Link |
yes: a physical link is present |
no: a physical link is not present |
|
Line Impedance |
The line impedance configured for the port |
Line Encoding |
The line encoding configured for the physical DS1 (T1) port |
Type |
The type of interface |
Buildout |
The line buildout (cable length) configured for physical DS1 ports on the 16-port T1/E1 ASAP Adapter card or 32-port T1/E1 ASAP Adapter card |
Length |
The line length configured for the physical DS1 port on the 16-port T1/E1 ASAP Adapter card or 32-port T1/E1 ASAP Adapter card |
Hardware Address |
The port hardware address |
Port Statistics |
|
Packets Input/Output |
The number of packets, delivered by this sublayer to a higher (sub) layer, which were not addressed to a unicast, multicast, or broadcast address at this sublayer. The total number of packets that higher-level protocols requested be transmitted and which were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent. |
Discards Input/Output |
The number of inbound/outbound packets chosen to be discarded to possibly free up buffer space |
Unknown Proto DiscardsInput/Output |
For packet-oriented interfaces, the number of packets received via the interface that were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing, the number of transmission units received via the interface that were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0. Unknown proto discards do not show up in the packet counts. |
lldp [nearest-bridge | nearest-non-tpmr | nearest-customer] [remote-info] [detail]
show>port>ethernet
This command displays LLDP information.
displays nearest bridge information
displays nearest non-two-port MAC relay (TPMR) information
displays nearest customer information
displays remote information on the bridge MAC
displays detailed LLDP information
The following outputs are examples of LLDP information:
LLDP Detail (Output Example, Table: Port LLDP Detail Field Descriptions )
*A:ALU-1># show port 1/2/2 ethernet lldp
===============================================================================
Link Layer Discovery Protocol (LLDP) Port Information
===============================================================================
Port 1/2/2 Bridge nearest-bridge
-------------------------------------------------------------------------------
Admin State : txAndRx Notifications : Disabled
Tunnel Nearest Bridge : Disabled
Transmit TLVs : portDesc sysCap
PortID TLV Subtype : tx-local
Management Address Transmit Configuration:
Index 1 (system) : Enabled Address : 10.20.30.40
Index 2 (IPv6 system) : Disabled Address : ::
Port 1/2/2 Bridge nearest-non-tpmr
-------------------------------------------------------------------------------
Admin State : disabled Notifications : Disabled
Transmit TLVs : None
PortID TLV Subtype : tx-local
Management Address Transmit Configuration:
Index 1 (system) : Disabled Address : 10.20.30.40
Index 2 (IPv6 system) : Disabled Address : ::
Port 1/2/2 Bridge nearest-customer
-------------------------------------------------------------------------------
Admin State : disabled Notifications : Disabled
Transmit TLVs : None
PortID TLV Subtype : tx-local
Management Address Transmit Configuration:
Index 1 (system) : Disabled Address : 10.20.30.40
Index 2 (IPv6 system) : Disabled Address : ::
===============================================================================
*A:ALU-1>#
Label |
Description |
---|---|
Admin State |
The LLDP transmission/reception frame handling |
Notifications |
Indicates whether LLDP notifications are enabled |
Tunnel Nearest Bridge |
n/a |
Transmit TLVs |
The optional TLVs that are transmitted by this port |
PortID TLV Subtype |
Indicates the setting for the port ID subtype: tx-if-alias, tx-fi-name, or tx-local |
Management Address Transmit Configuration |
|
Index 1 (system) Index 2 (IPv6 system) |
Details of the management address configuration. The 7705 SAR can only be configured to send or not send the system address. Enabled: the management address TLV is included in LLDPDUs sent by the port Disabled: the management address TLV is not included in LLDPDUs sent by the port |
Address |
The address transmitted by the port when tx-mgmt-address command is enabled |
*A:ALU-1># show port 1/2/2 ethernet lldp nearest-bridge detail
===============================================================================
Link Layer Discovery Protocol (LLDP) Port Information
===============================================================================
Port 1/2/2 Bridge nearest-bridge
-------------------------------------------------------------------------------
Admin State : txAndRx Notifications : Disabled
Transmit TLVs : portDesc sysCap
Management Address Transmit Configuration:
Index 1 (system) : Enabled Address : 10.20.30.40
Port LLDP Stats:
Tx Frames : 13 Tx Length Err Frames : 0
Rx Frames : 0 Rx Frame Discard : 0
Rx Frame Errors : 0 Rx TLV Discard : 0
Rx TLV Unknown : 0 Rx Ageouts : 0
===============================================================================
*A:ALU-1>#
*A:ALU-1># show port 1/2/2 ethernet lldp nearest-bridge remote-info detail
===============================================================================
Link Layer Discovery Protocol (LLDP) Port Information
===============================================================================
Port 1/2/2 Bridge nearest-bridge Remote Peer Information
-------------------------------------------------------------------------------
Remote Peer Index 2 at timestamp 12/02/2014 16:08:14:
Supported Caps : bridge router
Enabled Caps : bridge router
Chassis Id Subtype : 4 (macAddress)
Chassis Id : ac:fa:ff:00:00:00
PortId Subtype : 1 (interfaceAlias)
Port Id : 37814272
Port Description : 2/1/2, 10/100 Gig Eth SFP, ‟remport1” (from ifDesc RFC2863)
System Name : n/a
System Description : n/a
Remote Peer Index 2 management addresses at time 12/02/2014 16:08:14:
No remote management addresses found
===============================================================================
*A:ALU-1>#
Label |
Description |
---|---|
Admin State |
The LLDP transmission/reception frame handling |
Notifications |
Indicates whether LLDP notifications are enabled |
Transmit TLVs |
The optional TLVs that are transmitted by this port |
Index 1 (system) |
Details of the management address configuration. The 7705 SAR can only be configured to send or not send the system address. Enabled: the management address TLV is included in LLDPDUs sent by the port Disabled: the management address TLV is not included in LLDPDUs sent by the port |
Enabled Address |
The address transmitted by the port when the management address TLV is included in LLDPDUs sent by the port |
Port LLDP Stats |
|
Tx Frames |
The number of LLDP frames transmitted |
Tx Length Err Frames |
The number of frames with LLDPDU length violations caused by too many TLVs selected by the network manager. The packets are sent containing the mandatory TLVs and the maximum number of optional TLVs that will fit in the LLDP frame. |
Rx Frames |
The number of LLDP frames received |
Rx Frame Discard |
The number of LLDP frames received by the LLDP agent that were discarded for any reason. This counter can provide an indication that LLDP header formatting problems may exist with the local LLDP agent in the sending system, or that LLDPDU validation problems may exist with the local LLDP agent in the receiving system. |
Rx Frame Errors |
The number of invalid LLDP frames received by the LLDP agent on the indicated port while the LLDP agent is enabled |
Rx TLV Discard |
The number of LLDP TLVs discarded for any reason by the LLDP agent on the indicated port |
Rx TLV Unknown |
The number of LLDP TLVs received that are not recognized by the LLDP agent |
Rx Ageouts |
The number of age-outs that have occurred on the port |
Supported Caps |
Describes the system capabilities supported by the remote peer |
Enabled Caps |
Describes the system capabilities enabled on the remote peer |
Chassis Id Subtype |
An integer value and text definition that indicates the basis for the chassis ID entity listed in the chassis ID field |
Chassis Id |
The chassis identifier of the chassis containing the Ethernet port that sent the LLDPDU |
PortId Subtype |
An integer value and text definition that indicates the basis for the port ID entity listed in the port ID field |
Port Id |
The port identifier of the Ethernet port that sent the LLDPDU |
Port Description |
Describes the port that sent the LLDPDU and indicates that the description is the ifDescr object text string from RFC 2863 - IF MIB |
System Name |
The name of the system that sent the LLDPDU |
System Description |
Describes the system that sent the LLDPDU |