This section shows a configuration example for the network illustrated in Figure 1.
The following CLI excerpt shows the configuration required on PE4 for services 2000 (VPRN), BD-2003 and BD-2004 (ordinary BDs) and BD-2002 (SBD).
vprn 2000 name "tenant-2k" customer 1 create
route-distinguisher auto-rd
interface "bd-2003" create
address 10.41.0.1/24
vpls "bd-2003"
exit
exit
interface "bd-2004" create
address 10.42.0.1/24
vpls "bd-2004"
exit
exit
interface "bd-2002" create
vpls "bd-2002"
evpn-tunnel supplementary-broadcast-domain <------
exit
exit
igmp <------
interface "bd-2003" <------
no shutdown
exit
interface "bd-2004" <------
no shutdown
exit
no shutdown
exit
pim <------
interface "bd-2002" <------
multicast-senders always <------
exit
apply-to all <------
no shutdown
exit
no shutdown
exit
As shown in the previous configuration commands, the VPRN must be configured as follows.
The SBD interface in the VPRN must be configured as evpn-tunnel supplementary-broadcast-domain so that the OISM forwarding mode is enabled.
IGMP must be enabled on the ordinary BD (R-VPLS) interfaces so that the PEs can process the received IGMP messages from the receivers.
Even though the protocol itself is not used, PIM is enabled in the VPRN on all the IRB interfaces so that the multicast source addresses can be resolved. Also, multicast-senders always must be enabled on the SBD interface; this is because the SBD interface is unnumbered (it does not have an IP address associated) and the multicast traffic source RPF-check would discard the multicast traffic arriving at the SBD interface unless the system is informed that legal multicast traffic may be expected on the SBD. The multicast-senders always command is allows the system to process multicast on the unnumbered SBD interface.
Besides the VPRN, BD-2003, BD-2004 and BD-2002 (SBD) must be configured as follows.
vpls 2003 name "bd-2003" customer 1 create
allow-ip-int-bind
forward-ipv4-multicast-to-ip-int <------
exit
bgp
exit
bgp-evpn
evi 2003
mpls bgp 1
ingress-replication-bum-label
auto-bind-tunnel
resolution any
exit
no shutdown
exit
exit
igmp-snooping <------
no shutdown <------
exit
sap 1/1/1:2003 create
igmp-snooping
mrouter-port
exit
no shutdown
exit
no shutdown
exit
vpls 2004 name "bd-2004" customer 1 create
allow-ip-int-bind
forward-ipv4-multicast-to-ip-int <------
exit
bgp
exit
bgp-evpn
evi 2004
mpls bgp 1
ingress-replication-bum-label
auto-bind-tunnel
resolution any
exit
no shutdown
exit
exit
igmp-snooping <------
no shutdown <------
exit
sap 1/1/1:2004 create
igmp-snooping
fast-leave
exit
no shutdown
exit
no shutdown
exit
vpls 2002 name "bd-2002" customer 1 create
allow-ip-int-bind
forward-ipv4-multicast-to-ip-int <------
exit
bgp
exit
bgp-evpn
no mac-advertisement
ip-route-advertisement
sel-mcast-advertisement <------
evi 2002
mpls bgp 1
auto-bind-tunnel
resolution any
exit
no shutdown
exit
exit
igmp-snooping <------
no shutdown <------
exit
no shutdown
exit
As shown in the previous configuration commands, igmp-snooping no shutdown must be configured in ordinary and SBD R-VPLS services so that IGMP messages or SMET routes are processed by the IGMP module. Also, the command forward-ipv4-multicast-to-ip-int allows the system to forward multicast traffic from the R-VPLS to the VPRN interface.
Finally, bgp-evpn>sel-mcast-advertisement must be enabled on the SBD R-VPLS, so that the SBD aggregates the multicast state for all the ordinary BDs and advertises the corresponding SMET routes with the SBD route-target. In OISM mode, the SMET route is only advertised from the SBD R-VPLS and not from the other ordinary BD R-VPLSes.
PE2 and PE3 are configured with the VPRN (2000), ordinary BD (BD-2001) and SBD (BD-2002) as above. In addition, PE2 and PE3 are attached to ES-1 where a receiver is connected. Multicast state synchronization through BGP Multicast Synch routes is automatically enabled in R-VPLS services in OISM mode and no additional configuration is needed:
/* Example of ES-1 configuration and MCS on PE3. Similar configuration is needed in
PE2.
bgp-evpn
ethernet-segment "ES-1" virtual create
esi 01:00:00:00:00:00:01:00:00:00
service-carving
mode manual
manual
preference non-revertive create
value 30
exit
exit
exit
multi-homing single-active
lag 1
dot1q
q-tag-range 2001
exit
no shutdown
exit
When the previous configuration is executed in the three nodes, the EVPN routes are exchanged. BD2003 in PE4 receives IMET routes from the remote SBD PEs and creates "SBD" destinations to PE2 and PE3. Those SBD destinations are used to forward multicast traffic to PE2 and PE3, following the OISM forwarding procedures described in OISM Forwarding Plane. The following command shows an example of IMET route (flagged as SBD route working on OISM mode) and SMET route received on PE4 from PE2.
/* IMET route received from PE2 on PE4.
*A:PE-4# show router bgp routes evpn incl-mcast community target:64500:2002 hunt
<snip>
-------------------------------------------------------------------------------
RIB In Entries
-------------------------------------------------------------------------------
Nexthop : 192.0.2.2
From : 192.0.2.2
Res. Nexthop : 192.168.24.1
Local Pref. : 100 Interface Name : int-PE-4-PE-2
<snip>
Community : target:64500:2002
mcast-flags:SBD/NO-MEG/NO-PEG/OISM/NO-MLD-Proxy/NO-IGMP-Proxy <---
bgp-tunnel-encap:MPLS
<snip>
EVPN type : INCL-MCAST
Tag : 0
Originator IP : 192.0.2.2 <------
Route Dist. : 192.0.2.2:2002
<snip>
-------------------------------------------------------------------------------
PMSI Tunnel Attributes :
Tunnel-type : Ingress Replication
Flags : Type: RNVE(0) BM: 0 U: 0 Leaf: not required
MPLS Label : LABEL 524241
Tunnel-Endpoint: 192.0.2.2
-------------------------------------------------------------------------------
/* SMET route from PE2 received on PE4.
*A:PE-4# show router bgp routes evpn smet community target:64500:2002 hunt
<snip>
-------------------------------------------------------------------------------
RIB In Entries
-------------------------------------------------------------------------------
Nexthop : 192.0.2.2
From : 192.0.2.2
Res. Nexthop : 192.168.24.1
Local Pref. : 100 Interface Name : int-PE-4-PE-2
<snip>
Community : target:64500:2002 bgp-tunnel-encap:MPLS
<snip>
EVPN type : SMET
Tag : 0
Src IP : 0.0.0.0 <------
Grp IP : 239.0.0.4 <------
Originator IP : 192.0.2.2 <------
Route Dist. : 192.0.2.2:2002
<snip>
When PE4 receives the IMET routes from PE2 and PE3 SBDs, it identifies the routes as SBD routes in OISM mode, and PE4 creates special EVPN destinations on the BD-2003 service that are used to forward the multicast traffic. The SBD destinations are shown as Sup BCast Domain in the show command output.
*A:PE-4# show service id 2003 evpn-mpls
===============================================================================
BGP EVPN-MPLS Dest
===============================================================================
TEP Address Egr Label Num. MACs Mcast Last Change
Transport:Tnl Sup BCast Domain <---
-------------------------------------------------------------------------------
192.0.2.2 524241 0 m 11/26/2019 10:38:04
ldp:65537 Yes <------
192.0.2.3 524253 0 m 11/26/2019 10:38:28
ldp:65539 Yes <------
-------------------------------------------------------------------------------
Number of entries : 2
-------------------------------------------------------------------------------
Based on the reception of the SMET routes from PE2 and PE3, PE4 adds the SBD EVPN destinations to its MFIB on BD-2003.
*A:PE-4# show service id 2003 igmp-snooping base
===============================================================================
IGMP Snooping Base info for service 2003
===============================================================================
Admin State : Up
Querier : 10.41.0.1 on rvpls bd-2003
SBD service : 2002
-------------------------------------------------------------------------------
Port Oper MRtr Pim Send Max Max Max MVR Num
Id Stat Port Port Qrys Grps Srcs Grp From-VPLS Grps
Srcs
-------------------------------------------------------------------------------
sap:1/1/1:2003 Up Yes No No None None None Local 0
rvpls Up Yes No N/A N/A N/A N/A N/A N/A
sbd-mpls:192.0.2.2:524241 Up No No N/A N/A N/A N/A N/A 1 <------
sbd-mpls:192.0.2.3:524253 Up No No N/A N/A N/A N/A N/A 1 <------
===============================================================================
*A:PE-4# show service id 2003 igmp-snooping statistics
===============================================================================
IGMP Snooping Statistics for service 2003
===============================================================================
Message Type Received Transmitted Forwarded
-------------------------------------------------------------------------------
<snip>
EVPN SMET Routes 2 0 N/A <------
-------------------------------------------------------------------------------
*A:PE-4# show service id 2003 mfib
<snip>
-------------------------------------------------------------------------------
* * sap:1/1/1:2003 Local Fwd
* 239.0.0.4 sap:1/1/1:2003 Local Fwd
sbd-eMpls:192.0.2.2:524241 Local Fwd
sbd-eMpls:192.0.2.3:524253 Local Fwd
PE2 and PE3 also creates regular destinations and SBD destinations based on the reception of IMET routes. As an example, the show service id 2001 evpn-mpls command shows the destinations created by PE3 in the ordinary BD-2001.
*A:PE-3# show service id 2001 evpn-mpls
===============================================================================
BGP EVPN-MPLS Dest
===============================================================================
TEP Address Egr Label Num. MACs Mcast Last Change
Transport:Tnl Sup BCast Domain <------
-------------------------------------------------------------------------------
192.0.2.2 524241 0 m 11/26/2019 10:38:28
ldp:65538 Yes <------
192.0.2.2 524242 0 bum 11/26/2019 10:38:28
ldp:65538 No
192.0.2.2 524243 1 none 11/26/2019 10:38:28
ldp:65538 No
192.0.2.4 524245 0 m 11/26/2019 10:38:28
ldp:65537 Yes <------
-------------------------------------------------------------------------------
Number of entries : 4
-------------------------------------------------------------------------------
===============================================================================
In case of an SBD destination and a non-SBD destination to the same PE (PE2), IGMP only uses the non-SBD one in the MFIB. The non-SBD destination always has priority over the SBD destination. This can be seen in the show service id igmp-snooping base command in PE3, where the SBD destination to PE2 is down as long as the non-SBD destination is up.
*A:PE-3# show service id 2001 igmp-snooping base
===============================================================================
IGMP Snooping Base info for service 2001
===============================================================================
Admin State : Up
Querier : 10.0.0.3 on rvpls bd-2001
SBD service : 2002
-------------------------------------------------------------------------------
Port Oper MRtr Pim Send Max Max Max MVR Num
Id Stat Port Port Qrys Grps Srcs Grp From-VPLS Grps
Srcs
-------------------------------------------------------------------------------
sap:lag-1:2001 Down No No No None None None Local 1
rvpls Up Yes No N/A N/A N/A N/A N/A N/A
sbd-mpls:192.0.2.2:524241 Down No No N/A N/A N/A N/A N/A 0 <------
mpls:192.0.2.2:524242 Up No No N/A N/A N/A N/A N/A 1 <------
sbd-mpls:192.0.2.4:524245 Up No No N/A N/A N/A N/A N/A 0
===============================================================================
*A:PE-3# show service id 2001 mfib
===============================================================================
Multicast FIB, Service 2001
===============================================================================
Source Address Group Address Port Id Svc Id Fwd
Blk
-------------------------------------------------------------------------------
* 239.0.0.4 sap:lag-1:2001 Local Fwd
eMpls:192.0.2.2:524242 Local Fwd <---
Finally, to check the Layer 3 IIF and OIF entries on the VPRN services, enter the show router id pim group detail command. As an example, the command is executed in PE2:
*A:PE-2# show router 2000 pim group detail
===============================================================================
PIM Source Group ipv4
===============================================================================
Group Address : 239.0.0.4
Source Address : *
<snip>
===============================================================================
PIM Source Group ipv4
===============================================================================
Group Address : 239.0.0.4
Source Address : 10.41.0.41
<snip>
Up Time : 0d 00:13:20 Resolved By : rtable-u
Up JP State : Joined Up JP Expiry : 0d 00:00:00
Up JP Rpt : Pruned Up JP Rpt Override : 0d 00:00:00
Rpf Neighbor : 10.41.0.41
Incoming Intf : bd-2002
Outgoing Intf List : bd-2001
Curr Fwding Rate : 0.000 kbps
Forwarded Packets : 1000 Discarded Packets : 0
Forwarded Octets : 84000 RPF Mismatches : 0
Spt threshold : 0 kbps ECMP opt threshold : 7
Admin bandwidth : 1 kbps
-------------------------------------------------------------------------------
Groups : 2
===============================================================================